CyberData | 011186 | Owner Manual | Cyberdata 011186 SIP Outdoor Intercom Owner manual

Cyberdata 011186 SIP Outdoor Intercom Owner manual
Installation Quick Reference
Connecting the V3 Intercom (Service Loop Routing)
Ground Cable Installation
Ground Lug
Route cable(s) inside of the
Route Cable(s) inside Gang Box to
Gang
Box Creates
to create
the
service loop.
Service
Loop
Network Cable Installation
Route
of theBox to
Routecable(s)
Cable(s) inside
inside Gang
Service
Loop loop.
Gang Box Creates
to create
the service
The IP Endpoint Company
Network Cable
(not provided)
Ground Cable
(not provided)
VoIP V3 Intercom
SIP Compliant
011186
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
Default Gatewaya
Nut (to Ground Lug
inside of the Gang Box
10.0.0.1
a. Default if there is not a DHCP server present.
Typical System Installation
Securing the V3 Intercom
Caution
GENERAL ALERT
Equipment Hazard: Do not use an electric or power
screwdriver to fasten the face plate and PCB assembly to the
gang box. To prevent over-torque damage to the gasket, do
not apply more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion, and
effectively void the manufacturer's warranty.
2-Gang Box
VoIP Intercom
Note: To mount the intercom, use methods
compliant with local electrical codes.
Note: More installation and mounting
information is illustrated in the V3 Intercom
Operations Guide.
*More installation and mounting
information is illustrated in the
Operations Guide.
802.3af Compliant Ethernet Switch
1
VoIP Intercom
2
3
4
5
6
VoIP Intercom
IP Phone
IP PBX Server
Getting Started
•
Torx Key
Download the Operations Guide PDF file, from the Documentation web page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercomv3/docs.html
•
Create a plan for the locations of your V3 Intercoms.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Torx Screws
Faceplate &
PCB Assembly
Parts
(1) V3 Intercom
Assembly
Contacting CyberData
(1) T-15H Torx Key
Optional Accessories
(for gooseneck mounting)
Optional Accessories
(1) Spacer for half-inch set conduit connector
(4) Carriage bolt nuts
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930471H
(4) Security Torx Screw
(4) Carriage bolts
(1) 531085B hole plug assembly
(4) Carriage bolt washers
Quick Reference
Quick Reference
930471H
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Features
RTFM Button
Dimensions (Front and Side View)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
SW1
Microphone
Hole
To announce the device’s current IP address:
Speaker
Drain Hole
Note
Call Button
To restore the device to factory default settings:
•
•
Press and release the RTFM button within a five
second window.
The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
Dimensions (Rear View and Mounting Holes)
Side Conduit Network Cable Entry Restrictions
Dimensions are in Inches [Millimeter]
*More installation and mounting
information is illustrated in the
V3 Intercom Operations Guide.
0.869 [22.07]
ø0.280 [ø7.11]
(4 Places)
1/2" Conduit
Connector
(Not Provided)
Hole Plug
Assembly
ø0.854 [ø21.69]
3.380
[85.85]
Spacer
1.690
[42.93]
1.690
[42.93]
3.380 [85.85]
0.869 [22.07]
Network
Cable In
Terminal Block Connections
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Wire (IN)
Terminal Block
can accept
3
4
16 AWG wire
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
*Contacts 1 and 2 on the J3 terminal block are only
for powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
1/2" Conduit
(Not Provided)
930471H
Rear Conduit Network Cable Entry Restrictions
With Shroud
Without Shroud
Spacer
Spacer
1/2" Conduit
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
1
6
J3 Terminal Block
Approx. 29/64'
[11.5mm] with
Optional Shroud On
Quick Reference
Quick Reference
1/2" Conduit
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
Network
Cable In
930471H
Approx. 3/8"
[9.5mm] without
Optional Shroud On
Network
Cable In
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising