CyberData | 011414 | Operations Guide | Cyberdata 011414 SIP h.264 Video Outdoor Intercom with Keypad Operations Guide

Cyberdata 011414 SIP h.264 Video Outdoor Intercom with Keypad Operations Guide
The IP Endpoint Company
SIP-enabled h.264 Video
Outdoor Intercom with
Keypad
Operations Guide
Part #011414
Document Part #931338D
for Firmware Version 1.1.0
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
Operations Guide 931338D
Part # 011414
COPYRIGHT NOTICE:
© 2017, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
CyberData Corporation
931338D
Operations Guide
Pictorial Alert Icons
GENERAL ALERT
General Alert
This pictorial alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
Ground
This pictorial alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
CyberData Corporation
931338D
Operations Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The SIP-enabled h.264 Video Outdoor Intercom with Keypad enclosure is not
rated for any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
CyberData Corporation
931338D
Operations Guide
Revision Information
Revision 931338D, which corresponds to firmware version 1.1.0, was released on July 18, 2017,
and has the following changes:
•
Updates Table 1-1, "Specifications" to add the following:
Storage Temperature
Storage Altitude
Browsers Supported
The following browsers have been tested against firmware version 1.1.0:
Operations Guide
•
Internet Explorer (version: 10)
•
Firefox (also called Mozilla Firefox) (version: 23.0.1 and 25.0)
•
Chrome (version: 29.0.1547.66 m)
•
Safari (version: 5.1.7)
931338D
CyberData Corporation
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................4
1.4 Supported Protocols .................................................................................................................5
1.5 Supported SIP Servers .............................................................................................................5
1.6 Specifications ...........................................................................................................................6
2.1 Parts List ..................................................................................................................................7
Chapter 2 Installing the SIP-enabled h.264 Video Outdoor Intercom with
Keypad
7
2.2 Intercom Components ..............................................................................................................8
2.2.1 Call Button and Indicator Light .......................................................................................9
2.2.2 Dialing from the Keypad .................................................................................................9
2.3 Intercom Setup .......................................................................................................................10
2.3.1 Mechanical Adjustment ................................................................................................10
2.3.2 Field of View .................................................................................................................13
2.3.3 Intercom Connections ..................................................................................................14
2.3.4 Using the On-Board Relay ...........................................................................................16
2.3.5 Wiring the Circuit ..........................................................................................................17
2.3.6 Intercom Connectors ....................................................................................................21
2.3.7 Activity and Link LEDs .................................................................................................25
2.3.8 RTFM Button ................................................................................................................26
2.3.9 Adjusting the Intercom Volume .....................................................................................28
2.3.10 Adjust the Volume ......................................................................................................28
2.4 Configure the Intercom Parameters ......................................................................................29
2.4.1 Factory Default Settings ...............................................................................................29
2.4.2 Intercom Web Page Navigation ....................................................................................30
2.4.3 Using the Toggle Help Button .......................................................................................31
2.4.4 Log in to the Configuration Home Page .......................................................................33
2.4.5 Configure the Device ....................................................................................................37
2.4.6 Configure the Button Parameters .................................................................................41
2.4.7 Configure the Video Parameters .................................................................................45
2.4.8 Configure the Network Parameters .............................................................................48
2.4.9 Configure the SIP Parameters .....................................................................................51
2.4.10 Configure the Multicast Parameters ...........................................................................55
2.4.11 Configure the Sensor Configuration Parameters ........................................................58
2.4.12 Configure the Audio Configuration Parameters ..........................................................62
2.4.13 Configure the Events Parameters ..............................................................................67
2.4.14 Configure the Door Strike Relay .................................................................................73
2.4.15 Configure the Autoprovisioning Parameters ...............................................................75
2.5 Upgrade the Firmware ............................................................................................................86
2.6 Reboot the Device ..................................................................................................................89
2.7 Command Interface ................................................................................................................90
2.7.1 Command Interface Post Commands ..........................................................................90
Appendix A Mounting the SIP-enabled h.264 Video Outdoor Intercom
with Keypad
93
A.1 Mount the Intercom ................................................................................................................93
A.2 Dimensions ............................................................................................................................94
A.3 Overview of Installation Types ................................................................................................96
A.4 Network Cable Entry Restrictions ..........................................................................................97
A.4.1 Rear Conduit Network Cable Entry Restrictions (without Shroud) ..............................97
A.4.2 Rear Conduit Network Cable Entry Restrictions (with Shroud) ...................................97
A.5 Service Loop Cable Routing ..................................................................................................98
Operations Guide
931338D
CyberData Corporation
ii
A.6 Securing the Intercom ............................................................................................................99
A.7 Additional Mounting Options ................................................................................................100
A.7.1 Rear Conduit Mounting Option (Not Provided) ..........................................................100
A.7.2 Concrete Wall Mounting Option (Not Provided) .........................................................101
A.7.3 Goose Neck Mounting Option (Not Provided) ............................................................102
Appendix B Setting up a TFTP Server
103
B.1 Set up a TFTP Server ..........................................................................................................103
B.1.1 In a LINUX Environment ............................................................................................103
B.1.2 In a Windows Environment .......................................................................................103
Appendix C Troubleshooting/Technical Support
104
C.1 Frequently Asked Questions (FAQ) ......................................................................................104
C.2 Documentation .....................................................................................................................104
C.3 Contact Information ..............................................................................................................105
C.4 Warranty and RMA Information ............................................................................................105
Index
Operations Guide
106
931338D
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the SIP-enabled h.264 Video Outdoor Intercom with Keypad, look for a model number
label similar to the one shown in Figure 1-1. Confirm the following:
•
The model number on the label should be 011414.
•
The serial number on the label should begin with 414.
Figure 1-1. Model Number Label
www.cyberdata.net
SIP-enabled H.264 Video Outdoor
Intercom With Keypad
011414A / 021495* / 021498D
414000001
CAN ICES-3 (A)/NMB-3(A)
V1.0.0
00:20:F7:03:83:CA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Serial number begins with 414
Model number
Operations Guide
931338D
CyberData Corporation
Product Overview 2
Typical System Installation
1.2 Typical System Installation
The following figures illustrate how the SIP-enabled h.264 Video Outdoor Intercom with Keypad can
be installed as part of a VoIP phone system.
Figure 1-2. Typical Installation
802.3af Compliant Ethernet Switch
Intercom
IP Phone
IP PBX Server
Figure 1-3. Installation with the Network Dual Door Strike Relay
802.3at Compliant Ethernet Switch
Door Strike
Door Strike
011375 Network Dual
Door Strike Relay 
(sold separately)*
Intercom
IP Phone
IP PBX Server
*See the Quick-Reference Placemat or Operations Guide
of the relevant door strike relay for connection specifics.
Operations Guide
931338D
CyberData Corporation
Product Overview 3
Typical System Installation
Figure 1-4. Installation with the Door Strike Relay Module
802.3af Compliant Ethernet Switch
Door Strike
011269 Door Strike Relay
Module (sold separately)*
Intercom
IP Phone
IP PBX Server
*See the Quick-Reference Placemat or Operations Guide
of the relevant door strike relay for connection specifics.
Operations Guide
931338D
CyberData Corporation
Product Overview 4
Product Features
1.3 Product Features
The SIP-enabled h.264 Video Outdoor Intercom with Keypad has the following features:
Operations Guide
•
Integrates with Network Dual Door Strike Relay Module (part# 011375) and Door Strike Relay
Module (part# 011269)
•
PoE 802.3af enabled (Powered-over-Ethernet)
•
SIP compliant
•
Adjustable camera angle
•
12-key keypad with backlight
•
Programmable speed dial
•
Full-duplex voice operation
•
Supports SRST (Survivable Remote Site Telephony) in a Cisco environment
•
Network web management
•
Network adjustable speaker volume and microphone sensitivity
•
Network downloadable firmware
•
Doubles as a paging speaker
•
Dry relay contact for auxiliary control (controls external power)
•
Door closure and tamper alert signal
•
Optional Weather Shroud for even greater weather protection
•
IP65 rated enclosure
•
Conformal coated PCBA
•
Optional Security Torx screws with driver kit
•
Downloadable alert, ringtones and callout messages
931338D
CyberData Corporation
Product Overview 5
Supported Protocols
1.4 Supported Protocols
The Intercom supports:
•
SIP
•
HTTP Web-based configuration
•
Provides an intuitive user interface for easy system configuration and verification of Intercom
operations.
•
DHCP Client
•
Dynamically assigns IP addresses in addition to the option to use static addressing.
•
TFTP Client
•
Facilitates hosting for the Autoprovisioning configuration file.
•
RTP
•
RTP/AVP - Audio Video Profile
•
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
Packet Time 20 ms
1.5 Supported SIP Servers
The following link contains information on how to configure the device for the supported SIP servers:
http://www.cyberdata.net/connecting-to-ip-pbx-servers/
Operations Guide
931338D
CyberData Corporation
Product Overview 6
Specifications
1.6 Specifications
Table 1-1. Specifications
Specifications
Ethernet I/F
10/100 Mbps
Protocol
SIP RFC 3261 Compatible
Power Input
PoE 802.3af compliant or +8 to +12VDC @ 1000mA Regulated Power Supplya
Speaker Output
2 Watts Peak Power
On-Board Relay
1A at 30 VDC
Operating Range
Temperature: -40o C to 55o C (-40o F to 131o F)
Humidity: 5-95%, non-condensing
Storage Temperature
-40o C to 70o C (-40o F to 158o F)
Storage Altitude
Up to 15,000 ft. (4573 m)
IP Rating
IP65
Audio Payload Types
G711, A-law and µ-law
Video Codec
H.264 Baseline
Camera Resolution
320 x 240
SIP Video Payload
Baseline profile @ 320x240
Video Lens Angle
72 degrees
Dimensionsb
7.480 in. [190 mm] Length
2.284 in. [58 mm] Width
5.118 in. [130 mm] Height
Weight
2.8 lbs. [1.27 kg]
Boxed Weight
4.0 lbs. [1.81 kg]
Weather Shroud is 1.2 lbs. [0.54 kg]
Part Number
011414
011215 Weather Shroud (sold separately)
a. Contacts 1 and 2 on the J3 terminal block are only for powering the device from a non-PoE 12VDC
power source as an alternative to Network PoE power. Use of these contacts for any other purpose will
damage the device and void the product warranty.
b. Dimensions are measured from the perspective of the product being upright with the front of the product
facing you.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 7
Parts List
2 Installing the SIP-enabled h.264 Video
Outdoor Intercom with Keypad
2.1 Parts List
Table 2-2 illustrates the parts for the SIP-enabled h.264 Video Outdoor Intercom with
Keypad.
Note
See Appendix A, "Mounting the SIP-enabled h.264 Video Outdoor Intercom
with Keypad" for physical mounting information.
Table 2-2. Parts List
Operations Guide
Quantity
Part Name
1
SIP-enabled h.264 Video Outdoor Intercom with
Keypad Assembly
1
Installation Quick Reference Guide
1
Mounting Accessory Kit
931338D
Illustration
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 8
Intercom Components
2.2 Intercom Components
Figure 2-1 shows the components of the Intercom.
Figure 2-1. Intercom Components
Speaker
Camera
Keypad
See Section 2.2.2, "Dialing from
the Keypad" for 
information about the functionality
of the keypad.
Call Button
See Section 2.2.1, "Call Button
and Indicator Light" for 
information about the functionality
of the Call Button.
Microphone Hole
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 9
Intercom Components
2.2.1 Call Button and Indicator Light
2.2.1.1 Indicator Light Function
•
Upon initial power or reset, the Call Button LED will illuminate.
•
During network setup the Call Button LED will blink 10 times per second until the device can find
a network address. This can take from 5 to 60 seconds.
•
When the software has finished initialization, the Call Button LED will blink twice.
•
When a call is established (not just ringing), the Call Button LED will blink.
•
On the Device Configuration Page, there is an option called Button and Keypad Lit when
Idle. This option sets the normal state for the indicator light. The indicator light will still blink
during initialization and calls.
•
The indicator light flashes briefly at the beginning of RTFM mode.
Figure 2-2. Call Button and Indicator Light
Call button and indicator light
2.2.2 Dialing from the Keypad
•
Operations Guide
See the Enable Telephone Operation setting in Section 2.4.6, "Configure the Button
Parameters".
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 10
Intercom Setup
2.3 Intercom Setup
2.3.1 Mechanical Adjustment
The SIP-enabled h.264 Video Outdoor Intercom with Keypad has a mechanical adjustment that
ships in the default position of 0 degrees horizontal (Figure 2-3), but it allows you to tilt it 15 degrees
down or 15 degrees up as shown in Figure 2-4 and Figure 2-5.
Figure 2-3. Mechanical Adjustment at 0 degrees horizontal
0 degrees
Camera
Screw used for adjustment
0 degrees
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 11
Intercom Setup
Figure 2-4. Mechanical Adjustment at +15 Degree Angle to - 15 Degree Angle
Stop
+/- 15 degrees
Camera
Screw used for adjustment
Stop
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 12
Intercom Setup
Figure 2-5. Mechanical Adjustment at +15 Degree Angle to - 15 Degree Angle
Stop
Screw used for adjustment
Camera
+/- 15 degrees
Stop
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 13
Intercom Setup
2.3.2 Field of View
Figure 2-6 shows the field of view of the SIP-enabled h.264 Video Outdoor Intercom with Keypad
when it is mounted at the recommended 48 to 52 inches above the ground.
Figure 2-6. Field of View
1.5m (4.92’)
1m (3.28’)
0.5m (1.64’)
2m (6.56')
73”
1.5m (4.92')
62”
57”
1m (3.28')
30”
0.5m (1.64')
Typical Height of Video Intercom
52” to center of camera
41”
5”
-15 degrees from horizontal
3’
0 degrees from horizontal
+15 degrees from horizontal
Operations Guide
2’
1’
20” (0.5m)
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 14
Intercom Setup
2.3.3 Intercom Connections
Figure 2-7 shows the pin connections on the terminal block. This terminal block can accept 
16 AWG gauge wire.
Note
As an alternative to using PoE power, you can supply +8 to +12VDC @ 1000mA Regulated
Power Supply into the terminal block.
Caution
GENERAL ALERT
Equipment Hazard: Contacts 1 and 2 on the terminal block are only for powering
the device from a non-PoE 12 VDC power source as an alternative to Network PoE
power. Use of these contacts for any other purpose will damage the device and void
the product warranty.
Figure 2-7. Intercom Connections
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
Terminal block can accept up to 16 AWG wire.
Tool required for terminal block screw:
Size #00 Phillip Drive Screwdriver
Wire(s) in
Tin Wire to 0.25 inch [6mm]
4
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for 
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 15
Intercom Setup
2.3.3.1 Remote Switch Connection
Wiring pins 7 and 8 of the terminal block to a switch will initiate a SIP call when the switch is closed.
The call will go to the extension specified as the dial out extension on the SIP page.
Figure 2-8. Remote Switch Connection
Wire(s) in
Tin Wire to 0.25 inch [6mm]
8 7
Terminal Block
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 16
Intercom Setup
2.3.4 Using the On-Board Relay
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: The relay contacts are dry and provided for a normally open
and momentarily closed configuration. Neither the alternate power input nor PoE
power can be used to drive a door strike.
GENERAL ALERT
Warning
Electrical Hazard: The relay does not support AC powered door strikes.
Any use of this relay beyond its normal operating range can cause damage to the
product and is not covered under our warranty policy.
GENERAL ALERT
The device has a built-in relay that can be activated by a web configurable DTMF string that can be
received from a VoIP phone supporting out of band (RFC2833) DTMF as well as a number of other
triggering events. See the Device Page on the web interface for relay settings.
This relay can be used to trigger low current devices like LED strobes and security camera input
signals as long as the load is not an inductive type and the relay is limited to a maximum of 
1 Amp @ 30 VDC. Inductive loads can cause excessive “hum” and can interfere with or damage the
unit’s electronics.
We highly recommend that inductive load and high current devices use our Network Dual Door
Strike Relay (CD# 011375) (see Section 2.3.5.2, "Network Dual Door Strike Relay Wiring Diagram
with External Power Source") or our Door Strike Intermediate Relay product (CD# 011269) (see
Section 2.3.5.4, "Door Strike Relay Module Wiring Diagram from Intercom").
This relay interface also has a general purpose input port that can be used to monitor an external
switch and generate an event.
For more information on the sensor options, see the Sensor Configuration Page on the web
interface.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 17
Intercom Setup
2.3.5 Wiring the Circuit
2.3.5.1 Devices Less than 1A at 30 VDC
If the power for the device is less than 1A at 30 VDC and is not an inductive load, then see
Figure 2-9 for the wiring diagram.
When configuring with an inductive load, please use an intermediary relay with a High PIV Ultrafast
Switching Diode. We recommend using the CyberData Networked Dual Door Strike Intermediate
Relay Module (CD# 011375) (see Section 2.3.5.2, "Network Dual Door Strike Relay Wiring Diagram
with External Power Source").
Figure 2-9. Devices Less than 1A at 30 VDC
Pin 3 - Relay Common
Pin 4 - Relay Normally Open Contact
Pin 5 - Sense Input
Pin 6 - Sense Ground
The terminal block can accept 16 AWG stranded wire.
LED Strobe Light
1
8
+
DC Source
Sense Input
1 A @ 30 VDC
Terminal Block of the CyberData Device
If you have questions about connecting door strikes or setting up the web configurable options,
please contact our support department at the following website:
http://support.cyberdata.net/
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 18
Intercom Setup
2.3.5.2 Network Dual Door Strike Relay Wiring Diagram with External Power Source
For wiring an electronic door strike to work over a network, we recommend the use of our external
Network Dual Door Strike Relay (CD# 011375).
This product provides an easier method of connecting standard door strikes as well as AC and
higher voltage devices. See Figure 2-10 and Figure 2-11 for the wiring diagrams.
Warning
Electrical Hazard: Hazardous voltages may be present. No user serviceable
part inside. Refer to qualified service personnel for connecting or servicing.
GENERAL ALERT
Figure 2-10. Network Dual Door Strike Relay Wiring Diagram with External Power Source
802.3af Compliant Ethernet Switch
CyberData
Device
+
The relay connection maximum wire
size is 12 gauge stranded wire.
+
AC Source 1
AC Source 2
Door Strike
DC Source 2 OR
Door Strike
DC Source 1 OR
*
*
See the Network Dual Door Strike Relay
Operations Guide for connection specifics.
Sense Input 1
See Section 2.4.15, "Configure the Autoprovisioning Parameters" for configuration options.
Aux Button1
Sense Input 2
Aux Button 2
*Caution
GENERAL ALERT
Equipment Hazard: The door strike must have an internal or external mov or
diode (for over voltage protection) when connecting directly to the module.
If you have questions about connecting door strikes or setting up the web configurable options,
please contact our support department at the following website:
http://support.cyberdata.net/
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 19
Intercom Setup
2.3.5.3 Network Dual Door Strike Relay Wiring Diagram Using PoE+
Figure 2-11. Network Dual Door Strike Relay Wiring Diagram Using PoE+
802.3at Compliant Ethernet Switch
CyberData
Device
Door Strike
Internal 12VDC
source (500 mA
maximum)
Door Strike
The relay connection maximum wire
size is 12 gauge stranded wire.
*
*
See the Network Dual Door Strike Relay 
Operations Guide for connection specifics.
See Section 2.4.15, "Configure the Autoprovisioning Parameters" for configuration options.
Sense Input 1
Aux Button1
Sense Input 2
Aux Button 2
*Caution
GENERAL ALERT
Equipment Hazard: The door strike must have an internal or external mov or
diode (for over voltage protection) when connecting directly to the module.
If you have questions about connecting door strikes or setting up the web configurable options,
please contact our support department at the following website:
http://support.cyberdata.net/
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 20
Intercom Setup
2.3.5.4 Door Strike Relay Module Wiring Diagram from Intercom
For wiring an electronic door strike, we recommend the use of our external Door Strike Relay Module
(CD# 011269).
This product provides an easier method of connecting standard door strikes as well as AC and
higher voltage devices. See Figure 2-12 for the wiring diagram.
Figure 2-12. Door Strike Relay Module Wiring Diagram from Intercom
1
The terminal block can accept 16 AWG stranded wire.
8
Terminal Block
See the Door Strike Relay Module Operations
Guide for connection specifics.
See Section 2.4.15, "Configure the Autoprovisioning Parameters" for configuration options.
+
DC Source
AC Source
OR
Door Lock
Sense Input
If you have questions about connecting door strikes or setting up the web configurable options,
please contact our support department at the following website:
http://support.cyberdata.net/
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 21
Intercom Setup
2.3.6 Intercom Connectors
See the following figures and tables to identify the connectors and functions of the Intercom.
Figure 2-13. Connector Locations
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 22
Intercom Setup
Table 2-3. Connector Functions
Operations Guide
Connector
Function
JCAM
Camera Interface
H_AEC
Echo Cancellation Interface
JBTN
Call Button LED Interface
JMIC
Microphone Interface
JMIC2
Second Microphone Interface — Not Used
JSPKR
Speaker Interface
JKPAD
Keypad Interface — Not Used
JY
Sensor Interface — Not Used
JP3
Audio Mute — Factory Use Only
JP4
Boot from mSD Card — Factory Use Only
JP7
EPROM Write Protect — Factory Use Only
JP10
Disables the intrusion sensor when installed.
J17
Sitara Card Interface — Factory Use Only
JBT1
Touch Button -1 Interface — Not Used
JBT2
Touch Button -2 Interface — Not Used
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 23
Intercom Setup
Figure 2-14. Connector Locations
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 24
Intercom Setup
Table 2-4. Connector Functions
Connector
Function
J1
PoE Network Connection (RJ-45 ethernet)
JP5
Reset jumpera
JX
Auxiliary Strobe Interface
Q8
Intrusion Detector
JAEC
AEC Configuration Interface — Factory Use Only
JIO
Terminal Block (see Figure 2-7)
JCON
Console Port — Factory Use Only
JSPI
Reserved — Factory Use Only
SW1
See Section 2.3.8, "RTFM Button"
a.Do not install a jumper. Momentary short to reset. Permanent installation of a jumper would
prevent the board from running all together.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 25
Intercom Setup
2.3.7 Activity and Link LEDs
2.3.7.1 Verifying the Network Connectivity and Data Rate
When you plug in the Ethernet cable or power supply to the Intercom, the following occurs:
•
The square, GREEN Link/Activity LED blinks when there is network activity (see Figure 2-15).
•
The square, AMBER 100Mb Link LED above the Ethernet port indicates that a 100Mb network
connection has been established (see Figure 2-15).
Figure 2-15. Activity and Link LED
Link/Activity
LED (GREEN)
100Mb Link
LED (AMBER)
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 26
Intercom Setup
2.3.8 RTFM Button
When the Intercom is operational and linked to the network, you can use the Reset Test Function
Management (RTFM) button (see SW1 in Figure 2-16) on the Intercom board to announce and
confirm the Intercom’s IP Address and test to see if the audio is working.
Note
You must do these tests prior to final assembly.
Figure 2-16. RTFM Button
RTFM Button (SW1)
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 27
Intercom Setup
2.3.8.1 Announcing the IP Address
To announce a device’s current IP address:
1. Press and release the RTFM button (see SW1 in Figure 2-17) within a five second window.
Note
The device will use DHCP to obtain the new IP address (DHCP-assigned address or default
to 10.10.10.10 if a DHCP server is not present).
Note
Pressing and holding the RTFM button for longer than five seconds will restore the device to
the factory default settings.
Figure 2-17. RTFM Button
RTFM Button (SW1)
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 28
Intercom Setup
2.3.8.2 Restoring the Factory Default Settings
When troubleshooting configuration problems, it is sometimes convenient to restore the device to a
known state.
Note
Each Intercom is delivered with factory set default values.
To restore the factory default settings:
1. Press and hold the RTFM button (see SW1 in Figure 2-18) for more than five seconds.
2. The device announces that it is restoring the factory default settings.
Note
The device will use DHCP to obtain the new IP address (DHCP-assigned address or default
to 10.10.10.10 if a DHCP server is not present).
Figure 2-18. RTFM Button
RTFM Button (SW1)
2.3.9 Adjusting the Intercom Volume
You can adjust the Intercom volume through the SIP Volume, Multicast Volume, Ring Volume, and
Sensor Volume settings on the Device Page.
2.3.10 Adjust the Volume
You can adjust the volume through the Device Page.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 29
Configure the Intercom Parameters
2.4 Configure the Intercom Parameters
To configure the Intercom online, use a standard web browser.
Configure each Intercom and verify its operation before you mount it. When you are ready to mount
an Intercom, refer to Appendix A, "Mounting the SIP-enabled h.264 Video Outdoor Intercom with
Keypad" for instructions.
2.4.1 Factory Default Settings
All Intercoms are initially configured with the following default IP settings:
When configuring more than one Intercom, attach the Intercoms to the network and configure one at
a time to avoid IP address conflicts.
Table 2-5. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 30
Configure the Intercom Parameters
2.4.2 Intercom Web Page Navigation
Table 2-6 shows the navigation buttons that you will see on every Intercom web page.
Table 2-6. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Buttons page.
Link to the Video page.
Link to the Network page.
Link to go to the SIP page.
Link to the Multicast page.
Link to the Sensor page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Door Strike Relay page.
Link to the Autoprovisioning page.
Link to the Firmware page.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 31
Configure the Intercom Parameters
2.4.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-19 and Figure 2-20.
Figure 2-19. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-20.
Figure 2-20. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
?
?
Toggle Help button
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 32
Configure the Intercom Parameters
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-21.
), and a short description of the web
Figure 2-21. Short Description Provided by the Help Feature
?
?
A short description
of the web page
item will appear
Question mark
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 33
Configure the Intercom Parameters
2.4.4 Log in to the Configuration Home Page
1. Open your browser to the Intercom IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Intercom.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following link:
http://www.cyberdata.net/assets/common/discovery.zip
Note
The Intercom ships in DHCP mode. To get to the Home page, use the discovery utility to
scan for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-22):
Web Access Username: admin
Web Access Password: admin
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 34
Configure the Intercom Parameters
Figure 2-22. Home Page
CyberData Keypad Intercom
414000001
v1.1.0
v1.1.0
v1.1.0
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 35
Configure the Intercom Parameters
3. On the Home page, review the setup details and navigation buttons described in Table 2-7.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-7. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
Partition 2
Contains a complete copy of bootable software.
Partition 3
Contains an alternate, complete copy of bootable software.
Booting From
Indicates the partition currently used for boot.
Allows the user to boot from the alternate partition.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
SIP Volume
Shows the current SIP volume level.
Multicast Volume
Shows the current Multicast volume level.
Ring Volume
Shows the current Ring volume level.
Sensor Volume
Shows the current Sensor volume level.
Microphone Gain
Shows the current microphone gain level.
SIP Mode
Shows the current status of the SIP mode.
Multicast Mode
Shows the current status of the Multicast mode.
Event Reporting
Shows the current status of the Event Reporting mode.
Nightringer
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Nightringer Server
Shows the current status of Nightringer Server.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 36
Configure the Intercom Parameters
Table 2-7. Home Page Overview (continued)
Web Page Item
Description
Import Settings
Use this button to select a configuration file to import.
After selecting a configuration file, click Import to import the
configuration from the selected file. Then, click Save and Reboot to
store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you will
see a question mark ( ) appear next to some of the web page items.
Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Note
Operations Guide
The user name and password will be saved immediately, but the user will not be prompted
to enter them until there is a reboot. It is advisable to restart the web browser after this
change.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 37
Configure the Intercom Parameters
2.4.5 Configure the Device
1. Click the Device menu button to open the Device page. See Figure 2-23.
Figure 2-23. Device Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 38
Configure the Intercom Parameters
2. On the Device page, you may enter values for the parameters indicated in Table 2-8.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-8. Device Page Parameters
Web Page Item
Description
Volume Settings (0-9)
SIP Volume
Set the speaker volume for a SIP call. A value of 0 will mute the speaker
during SIP calls.
Multicast Volume
Set the speaker volume for multicast audio streams. A value of 0 will mute
the speaker during multicasts.
Ring Volume
Set the ring volume for incoming calls. A value of 0 will mute the speaker
instead of playing the ring tone when Auto-Answer Incoming Calls is
disabled.
Sensor Volume
Set the speaker volume for playing sensor activated audio. A value of 0 will
mute the speaker during sensor activated audio.
Microphone Gain
Set the microphone gain level.
Clock Settings
NTP Server
Use this field to set the address (in IPv4 dotted decimal notation or as a
canonical name) for the NTP Server. This field can accept canonical
names of up to 64 characters in length.
Timezone
Enter the tz database string of your timezone.
Examples:
America/Los_Angeles
America/New_York
Europe/London
America/Toronto
See https://en.wikipedia.org/wiki/List_of_tz_database_time_zones for
a full list of valid strings.
Current Time
Displays the current time.
Relay Settings
Activate Relay with DTMF Code
Activates the relay when the DTMF Activation Code is entered on the
phone during a SIP call with the device. RFC2833 DTMF payload types
are supported.
Relay Pulse Code
DTMF code used to pulse the relay when entered on a phone during a SIP
call with the device. Relay will activate for Relay Pulse Duration seconds
then deactivate. Activate Relay with DTMF Code must be enabled. Enter
up to 25 digits (* and # are supported).
Relay Pulse Duration (in seconds)
The length of time (in seconds) during which the relay will be activated
when the DTMF Relay Activation Code is detected. Enter up to 5 digits.
Relay Activation Code
Activation code used to activate the relay when entered on a phone during
a SIP call with the device. Relay will be active indefinitely, or until the
DTMF Relay Deactivation code is entered. Activate Relay with DTMF
Code must be enabled. Enter up to 25 digits (* and # are supported).
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 39
Configure the Intercom Parameters
Table 2-8. Device Page Parameters (continued)
Web Page Item
Description
Relay Deactivation Code
Code used to deactivate the relay when entered on a phone during a SIP
call with the device. Activate Relay with DTMF Code must be enabled.
Enter up to 25 digits (* and # are supported).
Play tone during DTMF Activation
When selected, the device will play a tone out of the speaker upon DTMF
relay activation. The tone plays for the DTMF Activation Duration (in
seconds).
Activate Relay During Ring
When selected, the relay will be activated for as long as the device is
ringing. When Auto-Answer Incoming Calls is enabled, the device will not
ring and this option does nothing.
Activate Relay During Night Ring
When selected, the relay will be activated as long as the Nightringer
extension is ringing.
Activate Relay While Call Active
When selected, the relay will be activated as long as the SIP call is active.
Activate Relay on Button Press
When selected, the relay will be activated when the Call button is pressed.
Relay on Button Press Duration
The length of time (in seconds) during which the relay will be activated
when the Call button is pressed. Enter up to 5 digits. A Relay on Button
Press Duration value of 0 will pulse the relay once when the Call button is
pressed.
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Auto-Answer Incoming Calls
When selected, the device will automatically answer incoming calls. When
Auto-Answer Incoming Calls is disabled, the device will play a ring tone
(corresponds to Ring Tone on the Audiofiles page) out of the speaker until
someone presses the Call button to answer the call or the caller
disconnects before the call can be answered.
Button Lit When Idle
When selected, the Call button LED is illuminated while the device is idle
(a call is not in progress).
Button Brightness (0-255)
The desired Call button LED brightness level. Acceptable values are 0255, where 0 is the dimmest and 255 is the brightest. Enter up to three
digits.
Keypad Lit When Idle
When selected, the keypad is illuminated while the device is idle (a call is
not in progress).
Keypad Brightness (0-255)
The desired keypad brightness level. Acceptable values are 0-255, where
0 is the dimmest and 255 is the brightest. Enter up to three digits.
Play Ringback Tone
When selected, the device will play a ringback tone (corresponds to
Ringback Tone on the Audiofiles page) out of the speaker while placing an
outbound call. The Ringback Tone will play until the call is answered.
Enable Push to Talk
This option is for noisy environments. When enabled, the microphone will
be muted normally. When the Call button is pressed and held, it will
unmute the microphone and allow the operator to send audio back. Using
Push to Talk prevents the operator from terminating a call by pressing the
Call button. The call must be terminated by the phone user.
Enable DTMF Push to Talk
This option is for noisy environments. When enabled, in an active call, the
remote phone can force receive only audio (setting the mic gain to max
and muting the speaker) by pressing the * key.
Pressing the # key will force send only audio (setting the max speaker
volume and muting the mic). Pressing the 0 key will restore full duplex
operation with the normal microphone and speaker volume.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 40
Configure the Intercom Parameters
Table 2-8. Device Page Parameters (continued)
Web Page Item
Description
Prevent Call Termination
When this option is enabled, a call cannot be terminated using the call
button.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do not
recommend disabling HTTPS for security reasons.
Click on the Test Audio button to do an audio test. When the Test Audio
button is pressed, you will hear a voice message for testing the device
audio quality and volume.
Click on the Test Microphone button to do a microphone test. When the
Test Microphone button is pressed, the following occurs:
1. The device will immediately start recording 3 seconds of audio.
2. The device will beep (indicating the end of recording).
3. The device will play back the recorded audio.
Click on the Test Relay button to do a relay test.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Operations Guide
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
The SIP Volume, Multicast Volume, Ring Volume, and Sensor Volume settings do not
require a reboot for the changes to take effect.
Note
None of the Relay Settings require a reboot for the changes to take effect.
Note
The Disable HTTPS (NOT recommended) setting requires a reboot for the changes to take
effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 41
Configure the Intercom Parameters
2.4.6 Configure the Button Parameters
1. Click the Button Config button to open the Button Configuration page. See Figure 2-24.
Figure 2-24. Button Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 42
Configure the Intercom Parameters
2. On the Button Configuration page, you may enter values for the parameters indicated in
Table 2-9.
Table 2-9. Button Configuration Parameters
Web Page Item
Description
Dial Mode
Enable Telephone Operation
Dial extensions like a normal telephone. Pressing the call button will start a dial tone.
Pressing the call button in a call will cancel a call.
Enable Cellphone Operation
Enter your extension and press the call button to start the call. Press the call button again
to cancel the call.
Enable Speed Dial Operation
In speed dial mode every button can be configured to call a different extension when
pressed.
Enable Security Operation
Security mode allows the user to secure the local relay by requiring a code (up to 8 digits)
to be entered into the device's keypad. Security codes start with the pound key(#) and will
be recognized when the user stops pressing buttons or hits the pound key again.
Security Mode Settings
Security Code 0
Up to eight digits using characters 0 through 9 and *.
Security Code 1
Up to eight digits using characters 0 through 9 and *.
Security Code 2
Up to eight digits using characters 0 through 9 and *.
Security Code 3
Up to eight digits using characters 0 through 9 and *.
Security Code 4
Up to eight digits using characters 0 through 9 and *.
Security Code 5
Up to eight digits using characters 0 through 9 and *.
Security Code 6
Up to eight digits using characters 0 through 9 and *.
Security Code 7
Up to eight digits using characters 0 through 9 and *.
Security Code 8
Up to eight digits using characters 0 through 9 and *.
Security Code 9
Up to eight digits using characters 0 through 9 and *.
Relay Activation Code
Activation code used to activate the relay when entered on a phone during a SIP call with
the device. Relay will be active indefinitely, or until the DTMF Relay Deactivation code is
entered. Enter up to 25 digits (* and # are supported).
Relay Deactivation Code
Code used to deactivate the relay when entered on a phone during a SIP call with the
device. Enter up to 25 digits (* and # are supported).
Relay Activation Timeout
The time in seconds to activate the relay when a security code is entered. Up to five
numerical digits.
Play Tone While Relay Active
Play a tone when the relay is activated by a security code.
Allow Telephone Dialout
When enabled, the user will be able to use the call button to dial a pre-set extension,
specified on the web page.
Call Button
Dial this extension when the call button is pressed. Up to 64 characters.
ID
Type the desired Extension ID. Up to 64 characters.
Speed Dial Settings
Speed Dial Timeout
The amount of time you must hold the button before it calls the configured extension.
When this is set to 0 the phone will dial the configured extension as soon as the button is
released.
Keypad 1
Dial this extension when the 1 key is pressed.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 43
Configure the Intercom Parameters
Table 2-9. Button Configuration Parameters (continued)
Web Page Item
Description
Keypad 2
Dial this extension when the 2 key is pressed.
Keypad 3
Dial this extension when the 3 key is pressed.
Keypad 4
Dial this extension when the 4 key is pressed.
Keypad 5
Dial this extension when the 5 key is pressed.
Keypad 6
Dial this extension when the 6 key is pressed.
Keypad 7
Dial this extension when the 7 key is pressed.
Keypad 8
Dial this extension when the 8 key is pressed.
Keypad 9
Dial this extension when the 9 key is pressed.
Keypad 0
Dial this extension when the 0 key is pressed.
Keypad *
Dial this extension when the * key is pressed.
Keypad #
Dial this extension when the # key is pressed.
Call Button
Dial this extension when the call button is pressed.
Button Tones
Play Button Tones
Play a tone when the keypad buttons are pressed.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Start button to start a button test.
Click on the Toggle Help button to see a short description of some of the web page
items. First click on the Toggle Help button, and you will see a question mark ( ) appear
next to some of the web page items. Move the mouse pointer to hover over a question
mark to see a short description of a specific web page item.
Note
You must click on the Save button for the changes to take effect.
2.4.6.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the Button Configuration page, dial out extensions support the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-10. Examples of Dial-Out Extension Strings
Operations Guide
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 44
Configure the Intercom Parameters
Table 2-10. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
The maximum number of total characters in the dial-out field is 25.
2.4.6.2 Triggering a Dial Out Call or Security Code
You can instantly trigger a dial out call or security code by pressing the # key after dialing a number.
Table 2-11 shows the various actions that result from different keypad input.
Table 2-11. Triggering a Dial Out Call or Security Code
Allow Telephone Dialout Option Enabled (in security mode with default security settings)
Input
Resulting Action
Dialing 123 
The device will call extension 123 through the default SIP server.
(and waiting for several seconds)
Dialing #123 
The device will do nothing. The entry is an unrecognized security
(and waiting for several seconds) entry.
Dialing #1234560 
The device will activate the relay for Security Code 0 for 6 seconds.
(and waiting for several seconds)
Dialing #124560#
The device will instantly activate the relay for 6 seconds.
Dialing 123#
The device will instantly call extension 123 through the default SIP
server.
Allow Telephone Dialout Option Disabled (in security mode with default security settings)
Input
Resulting Action
Dialing 1234560 
The device will activate the relay for Security Code 0 for 6 seconds.
(and waiting for several seconds)
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 45
Configure the Intercom Parameters
2.4.7 Configure the Video Parameters
1. Click the Video menu button to open the Video page (Figure 2-26).
Figure 2-25. Video Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 46
Configure the Intercom Parameters
2. On the Video page, enter values for the parameters indicated in Table 2-13.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-12. Video Page Parameters
Web Page Item
Description
Brightness
The Brightness parameter brightens the entire image equally. Enter a
value between -64 and 64. The default value is 0.
Saturation
Saturation increases the separation between colors, and has a more
noticeable effect on vibrant colors, less on neutral colors, and no
effect on black and white images. Enter a value between 0 and 128.
The default value is 64.
Gamma
Gamma controls the image's grayscale. Increasing gamma can make
the image look brighter, because it increases the brightness of the
shadows and midtones without affecting the highlights. Enter a value
between 72 and 500. The default value is 100.
Power Line Frequency
The Power line Frequency option allows the user to select 50Hz,
60Hz, or disabled for the frequency of the power line. Adjust this
value if you're seeing flickering from fluorescent light sources. The
default value is 50Hz.
Backlight Compensation
Backlight Compensation allows the camera to adjust the exposure of
the entire image to properly expose the subject in the foreground, to
avoid silhouettes where there is a bright light source. Select 0, 1, or
2. The default value is 1.
White Balance Temperature Auto
White balance temperature auto allows the device to automatically
compensate for cast in lighting. Select "On" or "Off." The default
value is "On."
Contrast
Contrast is the separation between the darkest and brightest areas of
the image. Increasing contrast will make an image look more vibrant;
decreasing can make it look duller. Enter a value between 0 and 64.
The default value is 32.
Hue
Also referred to as "tint," hue affects the red/green balance of the
image. Enter a value between -40 and 40. The default value is 0.
Gain
Gain controls the amplification of the signal from the camera,
including background noise. Enter a value between 0 and 100. The
default value is 0.
Sharpness
Sharpness controls the contrast along and near the edges in the
image. Enter a value between 0 and 6. The default value is 3.
White Balance Temperature
White balance temperature compensates for cast in lighting, keeping
white and gray neutral. This setting is only applicable if "White
Balance Temperature Auto" is set to "off." Enter a value between
2800 and 6500. The default value is 4600.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 47
Configure the Intercom Parameters
Table 2-12. Video Page Parameters (continued)
Web Page Item
Description
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 48
Configure the Intercom Parameters
2.4.8 Configure the Network Parameters
1. Click the Network menu button to open the Network page (Figure 2-26).
Figure 2-26. Network Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 49
Configure the Intercom Parameters
2. On the Network page, enter values for the parameters indicated in Table 2-13.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-13. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking
the appropriate radio button. DHCP Addressing mode is enabled on
default and the device will attempt to resolve network addressing with
the local DHCP server upon boot. If DHCP Addressing fails, the
device will revert to the last known IP address or the factory default
address if no prior DHCP lease was established. See Section 2.4.1,
"Factory Default Settings" for factory default settings. Be sure to click
Save and Reboot to store changes when configuring a Static
address.
Hostname
This is the hostname provided by the DHCP server. See the
DHCP/DNS server documentation for more information. Enter up to
64 characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal
notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal
notation.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
VLAN Priority (0-7)
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of
0 may cause the VLAN ID tag to be ignored.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 50
Configure the Intercom Parameters
Table 2-13. Network Configuration Parameters (continued)
Web Page Item
Description
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 51
Configure the Intercom Parameters
2.4.9 Configure the SIP Parameters
1. Click on the SIP menu button to open the SIP page (Figure 2-27).
Figure 2-27. SIP Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 52
Configure the Intercom Parameters
2. On the SIP page, enter values for the parameters indicated in Table 2-14.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-14. SIP Configuration Parameters
Web Page Item
Description
SIP Settings
Enable SIP Operation
When enabled, the device will transmit, receive, and process SIP messages
according to the configured SIP settings below.
Primary SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a fully
qualified domain name. This parameter also becomes the host portion of the SIP-URI
for the device's extension on the primary SIP server. This field can accept entries of
up to 255 characters in length.
Primary SIP User ID
Specify the SIP User ID for the Primary SIP Server. This parameter becomes the user
portion of the SIP-URI for the device's extension on the primary SIP server. Enter up
to 64 alphanumeric characters.
Primary SIP Auth ID
Specify the Authenticate ID for the Primary SIP Server. This parameter is required for
SIP registration authentication. Enter up to 64 alphanumeric characters.
Primary SIP Auth Password
Specify the Authenticate Password for the Primary SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric characters.
Backup SIP Server 1
Enter the backup SIP server address as an IPv4 address in dotted decimal notation
or a fully qualified domain name. This parameter also becomes the host portion of the
SIP-URI for the device's extension on the backup SIP server. This field can accept
entries of up to 255 characters in length.
Backup SIP User ID 1
Specify the SIP User ID for the first backup SIP Server. This parameter becomes the
user portion of the SIP-URI for the device's extension on the first backup SIP server.
Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 1
Specify the Authenticate ID for the first backup SIP server. This parameter is required
for SIP registration authentication. Enter up to 64 alphanumeric characters.
Backup SIP Auth Password 1
Specify the Authenticate Password for the first backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric characters.
Backup SIP Server 2
Enter a second backup SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes the host
portion of the SIP-URI for the device's extension on the second backup SIP server.
This field can accept entries of up to 255 characters in length.
Backup SIP User ID 2
Specify the SIP User ID for the second backup SIP Server. This parameter becomes
the user portion of the SIP-URI for the device's extension on the second backup SIP
server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 2
Specify the Authenticate ID for the second backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric characters.
Backup SIP Auth Password 2
Specify the Authenticate Password for the second backup SIP server. This parameter
is required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the destination port
when sending SIP messages. The default Remote SIP Port is 5060. The supported
range is 0-65536. Enter up to 5 digits.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 53
Configure the Intercom Parameters
Table 2-14. SIP Configuration Parameters (continued)
Web Page Item
Description
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP messages.
The default Local SIP Port is 5060. The supported range is 0-65536. Enter up to 5
digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation or a
fully qualified domain name (FQDN). When an IP address is configured, the device
will send all SIP messages to this IP address. When an FQDN is configured, the
device will run DNS NAPTR, SRV, and A queries on the FQDN to resolve an IP
address to which it will send all SIP messages. This field can accept entries of up to
255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when sending
SIP messages to the outbound proxy. A value of 0 will default to 5060. The supported
range is 0-65536. Enter up to 5 digits.
Use Cisco SRST
When enabled, the backup servers are handled according to Cisco SRST (Survivable
Remote Site Telephony). It is required for use in clustered Cisco Unified
Communications Manager topologies.
Register with a SIP Server
When enabled, the device will attempt to register to the configured SIP Server(s) on
this page. To configure the device to send and receive point-to-point SIP calls, enable
SIP Operation and disable Register with a SIP Server (see Section 2.4.10,
"Configure the Multicast Parameters").
Disable rport Discovery
Disabling rport Discovery will prevent the device from including the public WAN IP
address and port number in the contact information that is sent to the remote SIP
servers. This will generally only need to be enabled when using an SBC or SIP ALG
in conjunction with a remote SIP server.
Unregister on Boot
When enabled, the device will send one registration with an expiry of 0 on boot.
Keep Alive Period
The minimum time in milliseconds between keep-alive packets sent for nat traversal.
A value of 0 will disable keep alive packets.
Nightringer Settings
SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a fully
qualified domain name. This parameter also becomes the host portion of the SIP-URI
for the device's Nightringer extension on the SIP server. This field can accept entries
of up to 255 characters in length.
SIP User ID
Specify the SIP User ID for the SIP server. This parameter becomes the user portion
of the SIP-URI for the device's Nightringer extension. Enter up to 64 alphanumeric
characters.
SIP Auth ID
Specify the Authenticate ID for the SIP Server. This parameter is required for SIP
registration authentication. Enter up to 64 alphanumeric characters.
SIP Auth Password
Specify the Authenticate Password for the SIP Server. This parameter is required for
SIP registration authentication. Enter up to 64 alphanumeric characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease time, also
known as the expiry. The supported range is 30-3600 seconds. Enter up to 4 digits.
Call Disconnection
Terminate Call After Delay
Automatically terminate an active call after a given delay in seconds. A value of 0 will
disable this function. Enter up to 8 digits.
RTP Settings
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 54
Configure the Intercom Parameters
Table 2-14. SIP Configuration Parameters (continued)
Web Page Item
Description
RTP Port (even)
Specify the port number used for the RTP stream after establishing a SIP call. This
port number must be an even number and defaults to 10500. The supported range is
0-65536. Enter up to 5 digits.
Jitter Buffer
Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid values are
50-1000.
Note: It may be necessary to adjust the jitter buffer on the device receiving the video.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web page
items. First click on the Toggle Help button, and you will see a question mark ( )
appear next to some of the web page items. Move the mouse pointer to hover over a
question mark to see a short description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
The Terminate Call After Delay setting does not require a reboot for the changes to take
effect.
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/connecting-to-ip-pbx-servers/
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 55
Configure the Intercom Parameters
2.4.10 Configure the Multicast Parameters
The Multicast Configuration page allows the device to join up to ten paging zones for receiving
ulaw/alaw encoded RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3. The device
supports simultaneous SIP and Multicast.
1. Click on the Multicast menu button to open the Multicast page. See Figure 2-28.
Figure 2-28. Multicast Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 56
Configure the Intercom Parameters
2. On the Multicast page, enter values for the parameters indicated in Table 2-15.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-15. Multicast Page Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Priority
Indicates the priority for the multicast group. Priority 9 is the highest (emergency
streams). 0 is the lowest (background music). SIP calls are considered priority 4.5.
See Section 2.4.10.1, "Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15 character limit).
Port
Enter the port number for this multicast group (5 character limit [range can be from
2000 to 65535]).
Note: The multicast ports have to be even values. The webpage will enforce this
restriction.
Name
Assign a descriptive name for this multicast group (25 character limit).
Buffer
Device will buffer up to four minutes of audio and then play back the recording after
the multicast stream finishes or after the buffer is full.
Beep
When selected, the device will play a beep before multicast audio is sent.
Relay
When selected, the device will activate a relay before multicast audio is sent.
Use this button to preview the strobe flashing behavior for the Multicast Strobe
Settings.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question mark
( ) appear next to some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web page item.
Operations Guide
Note
You must click on the Save button for the changes to take effect.
Note
Changing the Enable Multicast Operation, Address, Beep, or Relay settings require a
reboot for the changes to take effect.
Note
Enabling or disabling the strobe or changing any of the strobe options require you to click on
the Save button for the changes to take effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 57
Configure the Intercom Parameters
2.4.10.1 Assigning Priority
The device will prioritize simultaneous audio streams according to their priority in the list.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams, the volume is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 58
Configure the Intercom Parameters
2.4.11 Configure the Sensor Configuration Parameters
The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state.
There is an option on the Sensor page to trigger on an open or short condition on these pins. The
door sensor alarm will be activated when the Door Open Timeout parameter has been met.
The intrusion sensor is an optical sensor installed on the Intercom board and will be activated when
the Intercom is removed from the case.
Each sensor can trigger up to five different actions:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
•
Loop an audio file out of the Intercom speaker until the sensor is deactivated
•
Call an extension and establish two way audio
•
Call an extension and play a pre-recorded audio file
Note
Operations Guide
Calling a preset extension can be set up as a point-to-point call, but currently can't send
delayed DTMF tones.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 59
Configure the Intercom Parameters
1. Click Sensor menu button to open the Sensor page (Figure 2-29).
Figure 2-29. Sensor Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 60
Configure the Intercom Parameters
2. On the Sensor page, enter values for the parameters indicated in Table 2-16.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-16. Sensor Configuration Parameters
Web Page Item
Description
Door Sensor Settings
Door Sensor Normally Closed
Select the inactive state of the door sensor. The door sensor is also known as
the Sense Input on the device's terminal block.
Door Open Timeout (in seconds)
The time (in seconds) the device will wait before it performs an action when the
on-board door sensor is activated. The action(s) performed are based on the
configured Door Sensor Settings below. Enter up to 5 digits.
Flash Button LED
When selected, the Call button LED will flash until the on-board door sensor is
deactivated (roughly 10 times/second).
Activate Relay
When selected, the device's on-board relay will be activated until the on-board
door sensor is deactivated.
Play Audio Locally
When selected, the device will loop an audio file out of the speaker until the door
sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the on-board door sensor
is activated. Use the Dial Out Extension field below to specify the extension the
device will call.
Dial Out Extension
Specify the extension the device will call when the on-board door sensor is
activated. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls. Enter up to 64
alphanumeric characters.
Play recorded audio
When selected, the device will call the Dial Out Extension and play an audio file
to the phone answering the SIP call (corresponds to Door Ajar on the
Audiofiles page).
Repeat Sensor Message
The number of times to repeat the audio message through the local speaker or
to the remote endpoint. A value of 0 will repeat forever. Enter a value from 065536.
Intrusion Sensor Settings
Flash Button LED
When selected, the Call button LED will flash until the intrusion sensor is
deactivated (roughly 10 times/second).
Activate Relay
When selected, the device's on-board relay will be activated until the intrusion
sensor is deactivated.
Play Audio Locally
When selected, the device will loop an audio file out of the speaker until the
intrusion sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the intrusion sensor is
activated. Use the Dial Out Extension field below to specify the extension the
device will call.
Dial Out Extension
Specify the extension the device will call when the intrusion sensor is activated.
Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls. Enter up to 64
alphanumeric characters.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 61
Configure the Intercom Parameters
Table 2-16. Sensor Configuration Parameters (continued)
Web Page Item
Description
Play recorded audio
When selected, the device will call the Dial Out Extension and play an audio file
(corresponds to Intrusion Sensor Triggered on the Audiofiles page) to the
phone answering the SIP call when the intrusion sensor is activated.
Repeat Intrusion Message
The number of times to repeat the audio message through the local speaker or
to the remote endpoint. A value of 0 will repeat forever. Enter a value from 065536.
Use this button to preview the strobe flashing behavior for the Intrusion Sensor
Strobe Settings.
Click the Test Door Sensor button to test the door sensor.
Click the Test Intrusion Sensor button to test the Intrusion sensor.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question
mark ( ) appear next to some of the web page items. Move the mouse pointer
to hover over a question mark to see a short description of a specific web page
item.
Operations Guide
Note
You must click on the Save button for the changes to take effect.
Note
None of the Sensor Configuration Page settings require a reboot for the changes to take
effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 62
Configure the Intercom Parameters
2.4.12 Configure the Audio Configuration Parameters
The Audiofiles page is used to add custom audio to the board. User uploaded audio will take
precedence over the audio files shipped with the Intercom.
1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-30).
Figure 2-30. Audiofiles Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 63
Configure the Intercom Parameters
Figure 2-31. Audiofiles Configuration Page (continued)
2. On the Audiofiles page, enter values for the parameters indicated in Table 2-17.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-17. Audiofiles Configuration Parameters
Web Page Item
Description
Available Space
Shows the space available for the user to save custom audio files if they want to change the
message when the door or sensor is triggered.
0-9
The name of the audio configuration option is the same as the spoken audio that plays on the
board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Operations Guide
Corresponds to the spoken word “dot.” (24 character limit)
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 64
Configure the Intercom Parameters
Table 2-17. Audiofiles Configuration Parameters (continued)
Web Page Item
Description
Audiotest
Corresponds to the message “This is the CyberData IP speaker test message...” (24 character
limit)
Page tone
Corresponds to a simple tone used for beep on initialization and beep on page (24 character
limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Restoring default
Corresponds to the message “Restoring default” (24 character limit).
Ringback Tone
This is the ringback tone that plays when calling a remote extension 
(24 character limit).
Ring Tone
This is the tone that plays when set to ring when receiving a call 
(24 character limit).
Intrusion Sensor Triggered Corresponds to the message “Intrusion Sensor Triggered” (24 character limit).
Door Ajar
Corresponds to the message “Door Ajar” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the same audio file that is
selected for the Ring Tone parameter.
Click on the Browse button to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the file by
using the Browse button. The Save button will delete any pre-existing user-uploaded audio files.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 65
Configure the Intercom Parameters
2.4.12.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-32 through
Figure 2-34.
Figure 2-32. Audacity 1
Figure 2-33. Audacity 2
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 66
Configure the Intercom Parameters
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-34. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 67
Configure the Intercom Parameters
2.4.13 Configure the Events Parameters
The Events page specifies a remote server that can be used to receive HTTP POST events when
actions take place on the board.
1. Click on the Events menu button to open the Events page (Figure 2-35).
Figure 2-35. Event Configuration Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 68
Configure the Intercom Parameters
2. On the Events page, enter values for the parameters indicated in Table 2-18.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-18. Events Configuration Parameters
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote
server and port number whenever a certain action takes place.
Select an event type below to generate an HTTP POST event.
Events
Enable Button Events
When selected, the device will report Call button presses.
Enable Call Start Events
When selected, the device will report the start of a SIP call.
Enable Call Terminated Events
When selected, the device will report the end of a SIP call.
Enable Relay Activated Events
When selected, the device will report relay activation.
Enable Relay Deactivated Events
When selected, the device will report relay deactivation.
Enable Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call. A Ring Event will not be generated when AutoAnswer Incoming Calls is enabled on the Device page.
Enable Night Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call to the Nightringer extension. As a reminder, the
Nightringer extension always rings upon an incoming SIP call and it
is not possible to alter this behavior.
Enable Multicast Start Events
When selected, the device will report when the device starts playing
a multicast audio stream.
Enable Multicast Stop Events
When selected, the device will report when the device stops playing
a multicast audio stream.
Enable Power On Events
When selected, the device will report when it boots.
Enable Sensor Events
When selected, the device will report when the on-board sensor is
activated.
Enable Remote Relay Events
When selected, the device will report when the remote relay (DSR)
is activated.
Enable Security Events
When enabled, the device will report when the intrusion sensor is
activated.
Enable 60 Second Heartbeat
When enabled, the device will report a Heartbeat event every 60
seconds. SIP registration is not required to generate Heartbeat
events.
Check All
Click on Check All to select all of the events on the page.
Uncheck All
Click on Uncheck All to de-select all of the events on the page.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 69
Configure the Intercom Parameters
Table 2-18. Events Configuration Parameters(continued)
Web Page Item
Description
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 065536. Enter up to 5 digits.
Server URL
Generally, the destination URL is the name of the application that
receives the events and the string in the HTTP POST command. It
can be a script used to parse and process the HTTP POST events.
Enter up to 127 characters.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question mark
to see a short description of a specific web page item.
Operations Guide
Note
You must click on the Save button for the changes to take effect.
Note
Enabling Event Generation or changing an Event Server setting requires a reboot for the
changes to take effect.
Note
Selecting particular events, Check All, or Uncheck All does not require a reboot for the
changes to take effect.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 70
Configure the Intercom Parameters
2.4.13.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 71
Configure the Intercom Parameters
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 72
Configure the Intercom Parameters
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 73
Configure the Intercom Parameters
2.4.14 Configure the Door Strike Relay
The Door Strike Relay (DSR) is a network device designed to control an electronic door strike. The
DSR is meant to be used as a replacement for (or an addition to) the on-board relay. In addition to
being a drop-in 12 Amp relay, the DSR can monitor and record when the door is open or closed.
The DSR can be configured to trigger in the following ways: on the entry of a DTMF code, manually
through the web interface, or by using a Windows application.
This section describes operations for running firmware version 4.8 or later of the Dual Door Strike
Relay. If you have an older version of the firmware, then please contact CyberData Technical
Support. The version number appears in the Discovered Remote Relays section on the DSR page
(Figure 2-36).
1. Click on the DSR menu button to open the DSR page (Figure 2-36).
Figure 2-36. DSR Page (not associated with any DSRs)
CyberData Keypad Intercom
This is the default page when the
device is not associated with any
DSRs. Please see the Dual Door
Strike Relay Operations Guide for
more settings and options on the
DSR page when the device is
associated with a DSR.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 74
Configure the Intercom Parameters
2. On the DSR page, enter values for the parameters indicated in Table 2-19.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-19. DSR Configuration Parameters (not associated with any DSRs)
Web Page Item
Description
Remote Relay Settings
The settings in this section will activate an associated door strike relay. If a door
strike relay is not associated with the device, then you will only see the words Not
associated with any DSRs.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web page
items. First click on the Toggle Help button, and you will see a question mark ( )
appear next to some of the web page items. Move the mouse pointer to hover over a
question mark to see a short description of a specific web page item.
Discovered Remote Relays
The Discovered Remote Relays section lists all of the networked door strike relays
on the network. To associate your device with a door strike relay, click on the
Associate button. This action allows the user to configure the door strike relay. Keep
in mind that a device may only be associated with one door strike relay.
Product Type
Displays the product type of the remote relay.
IP Address
Displays the IP address of the remote relay.
MAC Address
Displays the MAC address of the remote relay.
Serial Number
Displays the serial number of the remote relay.
Name
Displays the name of the remote relay.
Version
Displays the version of the remote relay.
Use this button to search for and find any remote relays that are available on the
network.
Use this button to view the settings of a remote relay that has been “discovered” after
pressing the Discover button.
Use this button to associate the remote relay with the device. Only one relay may be
associated with a device.
Use this button to disassociate the remote relay from the device. Only one relay may
be associated with a device. This button is only available when a relay is associated
with a device.
Operations Guide
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
Associating a DSR does not require a reboot. However, you should reboot the device after
disassociating a DSR.
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 75
Configure the Intercom Parameters
2.4.15 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-37.
Figure 2-37. Autoprovisioning Page
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 76
Configure the Intercom Parameters
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 220.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-20. Autoprovisioning Configuration Parameters
Web Page Item
Description
Disable Autoprovisioning
Prevent the device from automatically trying to download a
configuration file. See Section 2.4.15.1, "Autoprovisioning" for
more information.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted
decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename.
The default autoprovisioning filename is in the format of
<mac address>.xml.
Supported filename extensions are .txt, and .xml. The current
filename is denoted by an asterisk at the bottom of the
Autoprovisioning Page. Enter up to 256 characters.
A file may have any name with an xml extension. If a file
name is entered, the device will look for the specified file
name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download
autoprovisioning files.
Username
The username used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Password
The password used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Autoprovisioning Autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before
checking for new autoprovisioning files. Enter up to 6 digits. A
value of 0 will disable this option.
Autoprovision at time (HHMMSS)
The time of day the device will check for a new
autoprovisioning file. The time must be 6 characters in length
and in HHMMSS format. An empty value will disable this
option.
Autoprovision when idle
(in minutes > 10)
The idle time (in minutes greater than 10) after which the
device will check for a new autoprovisioning file. Enter up to 6
digits. A value of 0 will disable this option.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a
specific web page item.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 77
Configure the Intercom Parameters
Table 2-20. Autoprovisioning Configuration Parameters (continued)
Web Page Item
Description
Press the Download Template button to create an
autoprovisioning file for the device. See Section 2.4.15.3,
"Download Template Button"
Autoprovisioning log
Note
The autoprovisioning log provides information about the latest
autoprovisioning attempt (i.e. dhcp options and server
accessed and files parsed or not found).
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.4.15.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.4.15.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-20). This file contains every configuration option that can
be set on the board.
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData VoIP Intercom</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 78
Configure the Intercom Parameters
<!-<!-<!--
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 79
Configure the Intercom Parameters
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-21. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 80
Configure the Intercom Parameters
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 81
Configure the Intercom Parameters
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 82
Configure the Intercom Parameters
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 83
Configure the Intercom Parameters
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio Configuration page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 84
Configure the Intercom Parameters
2.4.15.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 85
Configure the Intercom Parameters
2.4.15.3 Download Template Button
The Download Template button allows the user to generate, download, edit, and then store an
autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Download Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-38). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-38.
Figure 2-38. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 86
Upgrade the Firmware
2.5 Upgrade the Firmware
Note
CyberData strongly recommends that you do not upgrade the firmware when the device is
likely to be in use.
To upgrade the firmware of your device:
1. Download the latest firmware file from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011414/
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
•
Autoprovisioning template
3. Log in to the Home page as instructed in Section 2.4.4, "Log in to the Configuration Home
Page".
4. Click on the Firmware menu button to open the Firmware page (Figure 2-39).
Figure 2-39. Firmware Page
5. Click on the Browse button, and then navigate to the location of the firmware file.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 87
Upgrade the Firmware
6. Select the firmware file. This reveals the Upload button (Figure 2-40).
Figure 2-40. Upload Button
Upload button
Status Messages
Upload Post Processing bar
Upload Progress bar
7. Click on the Upload button. After selecting the Upload button, you will see the progress of the
upload in the Upload Progress bar.
8. When the upload is complete, you will see the words Upload finished under Status Messages.
9. At this point, you will see the progress of the upload’s post processing in the Upload Post
Processing bar.
Note
Do not reboot the device before the upgrading process is complete.
10. When the process is complete, you will see the words SWUPDATE Successful under Status
Messages.
11. The device will reboot automatically.
12. The Home page will display the version number of the firmware and indicate which boot
partition is active.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 88
Upgrade the Firmware
Table 2-22 shows the web page items on the Firmware page.
Table 2-22. Firmware Page Parameters
Web Page Item
Description
Use the Browse button to navigate to the location of the Intercom firmware file
that you want to upload.
Click on the Upload button to automatically upload the selected firmware and
reboot the system.
Note: This button only appears after the user has selected a firmware file.
Upload progress
Status bar indicates the progress in uploading the file.
Upload Post Processing
Status bar indicates the progress of the software installation.
Status Messages
Messages relevant to the firmware update process appear here.
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 89
Reboot the Device
2.6 Reboot the Device
To reboot the device, complete the following steps:
1. Log in to the Home page as instructed in Section 2.4.4, "Log in to the Configuration Home
Page".
2. Click on the Reboot button on the Home page (Figure 2-41). A normal restart will occur.
Figure 2-41. Home Page
CyberData Keypad Intercom
414000001
v1.1.0
v1.1.0
v1.1.0
Reboot
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 90
Reboot the Device
2.7 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-23 use the free unix utility, wget commands. However, any program that
can send HTTP POST commands to the device should work.
2.7.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-23. Command Interface Post Commands
Device Action
HTTP Post Commanda
Reboot
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=reboot"
Place call to extension (example: extension 600)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=call&extension=600"
Test Relay
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=test_relay"
Test Audio
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=test_audio"
Speak IP Address
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=speak_ip_address"
Test Mic
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=test_mic"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "0=Play"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "1=Play"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "2=Play"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "3=Play"
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "4=Play"
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 91
Reboot the Device
Table 2-23. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "5=Play"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "6=Play"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "7=Play"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "8=Play"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "9=Play"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "d=Play"
Play the Audio Test
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "audiotest=Play"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "pagetone=Play"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "youripaddressis=Play"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "rebooting=Play"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "restoringdefault=Play"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "ringback=Play"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "ringtone=Play"
Play the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "intrusionsensortriggered=Play"
Play the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "doorajar=Play"
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "nightring=Play"
Operations Guide
931338D
CyberData Corporation
Installing the SIP-enabled h.264 Video Outdoor Intercom with Keypad 92
Reboot the Device
Table 2-23. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Swap boot partitions
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=swap_boot_partition"
a.Type and enter all of each http POST command on one line.
Operations Guide
931338D
CyberData Corporation
93
Appendix A: Mounting the SIP-enabled
h.264 Video Outdoor Intercom with Keypad
A.1 Mount the Intercom
Before you mount the Intercom, make sure that you have received all the parts for each Intercom.
Refer to Table A-1. See Table A-2 and Table A-3 for optional accessories.
Table A-1. Mounting Components (Part of the Accessory Kit)
Quantity
Part Name
6
Accessory Kit Security Torx MS
1
Mounting Component Security Torx Key
Illustration
Table A-2. Optional Accessories (for gooseneck mounting)
Quantity
Part Name
3
Carriage bolt nuts
3
Carriage bolts
3
Carriage bolt washers
Illustration
Table A-3. Optional Accessories
Operations Guide
Quantity
Part Name
1
Spacer for Half-inch Set Screw Connector
1
531085B Hole Plug Assembly
931338D
Illustration
CyberData Corporation
94
Mount the Intercom
A.2 Dimensions
5.198 [132.03]
5.118 [130.00]
Figure A-1. Unit Dimensions—Front and Side View
7.480 [190.00]
2.386 [60.59]
Dimensions are in Inches [Millimeter]
Figure A-1. Unit Dimensions—Rear View with Mounting Hole Locations
3.740 [95.00]
ø0.280 [ø7.11]
(3 Places)
ø0.854 [ø21.69]
0.869 [22.07]
1.690 [42.93]
1.690
[42.93]
3.380 [85.85]
Dimensions are in Inches [Millimeter]
Operations Guide
931338D
CyberData Corporation
95
Mount the Intercom
Figure A-2. Shroud Dimensions and Mounting Hole Locations
7.638 [194.00]
4.254 [108.06]
ø0.854 [ø21.69]
2.564 [65.13]
ø0.280 [ø7.11]
(3 PLACES)
3.434 [87.23]
3.380 [85.85]
3.819 [97.00]
7.638 [194.00]
Operations Guide
Dimensions are in Inches [Millimeter]
931338D
CyberData Corporation
96
Overview of Installation Types
A.3 Overview of Installation Types
An overview of the installation types and the required components are provided in Table A-4.
Table A-4. Overview of Installation Types
Installation Type
What You Need
Outdoor, on surface
011414 Intercom only
Outdoor, on surface with shroud (increased resistance)
011414 Intercom
011215 Weather Shroud (sold separately)
Operations Guide
931338D
CyberData Corporation
97
Network Cable Entry Restrictions
A.4 Network Cable Entry Restrictions
A.4.1 Rear Conduit Network Cable Entry Restrictions (without Shroud)
See Figure A-3 for the rear conduit cable entry restrictions (without Shroud).
Figure A-3. Rear Conduit Network Cable Entry Restrictions—Without Shroud
Add Spacer Here
Network Cable,
1/2" Conduit &
1/2" Conduit Connector
are not provided.
A.4.2 Rear Conduit Network Cable Entry Restrictions (with Shroud)
See Figure A-4 for the rear conduit cable entry restrictions (with shroud).
Figure A-4. Rear Conduit Network Cable Entry Restrictions—With Shroud
Add Spacer Here
Network Cable,
1/2" Conduit &
1/2" Conduit Connector
are not provided.
Operations Guide
931338D
CyberData Corporation
98
Service Loop Cable Routing
A.5 Service Loop Cable Routing
Figure A-5 and Figure A-6 illustrate how to route the cables to the Intercom to create a service loop.
Figure A-5. Ground Cable Service Loop Routing
Route Cable inside
the Custom Enclosure to
Creates Service Loop
Ground Lug
Custom
Enclosure
Faceplate &
PCB Assembly
Ground Cable
is Not Provided
Nut to Ground Lug
Inside the Custom Enclosure
Faceplate Mounting
Screw (6x)
Figure A-6. Network Cable Service Loop Routing
Route Cable inside
the Custom Enclosure to
Creates Service Loop
Network Cable
is Not Provided
Custom
Enclosure
Faceplate &
PCB Assembly
Faceplate Mounting
Screw (6x)
Operations Guide
931338D
CyberData Corporation
99
Securing the Intercom
A.6 Securing the Intercom
Use the four Security Torx screws to secure the Intercom. See Figure A-7.
Figure A-7. Securing the Intercom
Note: To mount the intercom, use methods
compliant with local electrical codes.
Custom
Enclosure
Faceplate &
PCB Assembly
Torx Screws
Torx Key
Caution
GENERAL ALERT
Operations Guide
Equipment Hazard: Do not use an electric or power screwdriver to fasten the face
plate and PCB assembly to the gang box. To prevent over-torque damage to the
gasket, do not apply more than 10 inch-pounds force. Over-torquing will cause the
gasket to tear, risk moisture intrusion, and effectively void the manufacturer's
warranty.
931338D
CyberData Corporation
100
Additional Mounting Options
A.7 Additional Mounting Options
A.7.1 Rear Conduit Mounting Option (Not Provided)
Figure A-8 illustrates a rear conduit mounting option for the SIP-enabled h.264 Video Outdoor
Intercom with Keypad.
Figure A-8. Optional Rear Conduit Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
For 1/2" Conduit Mounting
with Optional Shroud
Remove Hole Plug
Assembly prior
for Shroud Installation
1/4" Carriage Bolt (3x)
Apply RTV
Silicone Sealant
Around Conduit Hole
Network Cable &
Ground Cable
are Not Provided
1/2" Set Screw
Connector & Conduit
are Not Provided
Spacer
(One Provided)
Custom
Enclosure
1/2" Conduit
Weather Shroud
(Sold Separate)
* 1/2" Conduit, Network Cable,
1/2" Set Screw Connector, Ground Wire &
RTV Sealant are Not Provided
Apply RTV
Silicone Sealant
Around Mounting Holes
Faceplate &
PCB Assembly
1/4" Washer & Nut (3x)
Faceplate Mounting
Screw (6x)
Operations Guide
931338D
CyberData Corporation
101
Additional Mounting Options
A.7.2 Concrete Wall Mounting Option (Not Provided)
Figure A-9 illustrates a concrete wall mounting option for the SIP-enabled h.264 Video Outdoor
Intercom with Keypad.
Figure A-9. Optional Concrete Wall Mounting
*
For Rear Conduit Mounting
with Optional Weather Shroud
Remove Hole Plug Assembly
then Rotate Custom Enclosure 180
Side Entry Hole on Top
**
**
Network Cable &
Ground Cable
are Not Provided
1/4" Concrete Screws &
Wall Anchors (3x)
(Not Provided)
*
Hole Plug
Assembly
Apply RTV
Silicone Sealant
Around Mounting Holes
*
Faceplate &
PCB Assembly
Custom
Enclosure
Side Entry
Nut to Ground Lug
Inside the
Custom Enclosure
Faceplate Mounting
Screw (6x)
1/2" Conduit &
1/2" Set Conduit Connector
are Not Provided
Note: To mount the intercom, use methods
compliant with local electrical codes.
Operations Guide
Fiber Washer
(One Included)
For 1/2" Conduit
Wall Mounting (Left) with / without
Optional Weather Shroud
Remove Hole Plug Assembly
from Side Entry then Install it
on to Rear to Cover Hole
Network Cable &
Ground Cable
931338D
CyberData Corporation
102
Additional Mounting Options
A.7.3 Goose Neck Mounting Option (Not Provided)
Figure A-10 illustrates a gooseneck mounting option for the SIP-enabled h.264 Video Outdoor
Intercom with Keypad.
Figure A-10. Optional Goose Neck Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
Apply RTV Silicone Sealant
Around Hole
For Gooseneck Mounting
with Optional Shroud
Remove Hole Plug
Assembly prior
for Shroud Installation
Gooseneck
1/4" Round Head
Carriage Bolt (3x)
Custom
Enclosure
Shroud (Optional)
(Sold Separate)
Washer (3x)
Gooseneck
[Cutaway View
to Show
Cable Routing]
Nut (3x)
Apply RTV
Silicone Sealant
Around Mounting Holes
* Gooseneck, Grounding Rod,
Clamp, Network Cable & Ground Cable,
RTV Sealant are Not Provided
Faceplate &
PCB Assembly
Ground Cable
Nut to Ground Lug
Inside the Custom Enclosure
Faceplate Mounting
Screw (6x)
Operations Guide
Network
Cable in
931338D
CyberData Corporation
103
Appendix B: Setting up a TFTP Server
B.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
B.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
http://www.cyberdata.net/assets/common/Solarwinds.zip
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
931338D
CyberData Corporation
104
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
To see a list of frequently asked questions for your product, click on the FAQs tab at the following
webpage:
http://www.cyberdata.net/voip/011414/
C.2 Documentation
The documentation for this product is released in an English language version only.
To download PDF copies of CyberData product documentation, click on the Downloads tab at the
following webpage:
http://www.cyberdata.net/voip/011414/
Operations Guide
931338D
CyberData Corporation
105
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601, Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Extension 333
C.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
Operations Guide
931338D
CyberData Corporation
106
Index
configuration
audio 62
default IP settings 29
door sensor 58
intrusion sensor 58
network 45, 48
SIP 51
using Web interface 29
configuration home page 33
configuration page
configurable parameters 38, 46, 49
contact information 105
contact information for CyberData 105
current network settings 49
CyberData contact information 105
Numerics
16 AWG gauge wire 14
A
activate relay (door sensor) 60
activate relay (intrusion sensor) 60
activity LED 25
address, configuration login 33
alternative power input 6
announcing a device’s IP address 27
audio configuration 62
night ring tone parameter 64
audio configuration page 62
audio encodings 5
audio files, user-created 65
autoprovision at time (HHMMSS) 76
autoprovision when idle (in minutes > 10) 76
autoprovisioning 77
download template button 77
autoprovisioning autoupdate (in minutes) 76
autoprovisioning configuration 75, 76
autoprovisioning filename 76
autoprovisioning server (IP Address) 76
D
default
gateway 29
intercom settings 106
IP address 29
subnet mask 29
username and password 29
web login username and password 33
default gateway 29, 49
default intercom settings 28
default IP settings 29
default login address 33
device configuration 37
device configuration parameters 76
the device configuration page 75
device configuration page 37, 41, 42
device configuration parameters 38
device configuration password
changing for web configuration access 37
DHCP Client 5
dial mode 42
dial out call 44
dial out extension (door sensor) 60
dial out extension (intrusion sensor) 60
dial out extension strings 43, 55
dimensions 6, 94
shroud dimensions and mounting hole locations 95
unit dimensions—front and side view 94
unit dimensions—rear view and mounting hole
locations 94
discovery utility program 33
DNS server 49
door sensor 58, 60
B
backup SIP server 1 52
backup SIP server 2 52
backup SIP servers, SIP server
backups 52
C
call button
indicator light 9
call termination 40
changing
the web access password 37
Cisco SRST 53
command interface 90
commands 90
concrete wall mounting option (not provided) 101
conduit mounting option (not provided) 100
configurable parameters 38, 46, 49, 52
Operations Guide
931338D
CyberData Corporation
107
activate relay 60
dial out extension 60
door open timeout 60
door sensor normally closed 60
flash button LED 60
play audio locally 60
download autoprovisioning template button 77
DTMF push to talk 39
DTMF tones 43
DTMF tones (using rfc2833) 43, 55
import settings 36
import/export settings 36
indicator light 9
installation, typical intercom system 2
intercom configuration
default IP settings 29
intercom configuration page
configurable parameters 52
intrusion sensor 58, 60
activate relay 60
dial out extension 60
flash button LED 60
play audio locally 60
IP address 29, 49
IP addressing
default
IP addressing setting 29
E
electric screwdriver 99
enable night ring events 68
enable security operation 42
ethernet I/F 6
event configuration
enable night ring events 68
expiration time for SIP server lease 53
export settings 36
J
J3 terminal block, 16 AWG gauge wire 14
F
K
factory default settings 28
fastening, gang box 99
firmware
where to get the latest firmware 86
flash button LED (door sensor) 60
flash button LED (intrusion sensor) 60
keypad configuration page 41
L
gang box, fastening 99
gasket, avoid over-torque damage 99
get autoprovisioning template 77
goose neck mounting option (not provided) 102
lease, SIP server expiration time 53
LED
green link LED 25
yellow activity LED 25
lengthy pages 57
link LED 25
Linux, setting up a TFTP server on 103
local SIP port 53
log in address 33
H
M
home page 33
http POST command 90
http web-based configuration 5
MGROUP
MGROUP Name 56
mounting 93
additional mounting options 100
concrete wall mounting option (not provided) 101
conduit mounting option (not provided) 100
goose neck mounting option (not provided) 102
illustration of intercom mounting process 93
mounting an intercom 93
G
I
identifying your product 1
Operations Guide
931338D
CyberData Corporation
108
mounting components (part of the accessory kit) 93
network cable entry restrictions 97
overview of installation types 96
rear conduit network cable entry restrictions (with
shroud) 97
rear conduit network cable entry restrictions (without
shroud) 97
securing the intercom 99
service loop cable routing 98
mounting components (part of the accessory kit) 93
multicast configuration 62
Multicast IP Address 56
N
navigation (web page) 30
navigation table 30
network cable entry restrictions 97
network configuration 45
network configuration of intercom 48
Network Setup 48
nightring tones 57
Nightringer 14, 85
nightringer settings 53
NTP server 38
R
rear conduit network cable entry restrictions (with
shroud) 97
rear conduit network cable entry restrictions (without
shroud) 97
reboot 88
remote SIP port 52
reset test function management button 26
resetting the IP address to the default 93
restoring factory default settings 28, 106
ringtones 57
lengthy pages 57
RJ-45 24
rport discovery setting, disabling 53
RTFM button 26
RTFM jumper 26, 27, 28
RTP/AVP 5
O
on-board relay 6, 16
overview of installation types 96
P
packet time 5
pages (lengthy) 57
part number 6
parts list 7
password
for SIP server login 52
login 33
restoring the default 29
payload types 6
play audio locally (door sensor) 60
play audio locally (intrusion sensor) 60
point-to-point configuration 55
port
local SIP 53
remote SIP 52
POST command 90
power input 6
alternative 6
Operations Guide
power screwdriver 99
priority
assigning 57
product
configuring 29
parts list 7
product features 4
product overview
product features 4
product specifications 6
supported protocols 5
supported SIP servers 5
typical system installation 2
product specifications 6
protocol 6
protocols supported 5
push to talk, DTMF 39
S
sales 105
securing the intercom 99
security code 44
security mode settings 42
sensor setup page 59, 73
sensor setup parameters 58
sensors 60
server address, SIP 52
service 105
service loop cable routing 98
setting up an intercom 10
settings, default 28
shroud dimensions and mounting hole locations 95
931338D
CyberData Corporation
109
SIP
VLAN Priority 49
VLAN tagging support 49
VLAN tags 49
volume
microphone gain 38
multicast volume 38
ring volume 38
sensor volume 38
SIP volume 38
enable SIP operation 52
local SIP port 53
user ID 52
SIP (session initiation protocol) 5
SIP configuration 51
SIP Server 52
SIP configuration parameters
outbound proxy 53
registration and expiration, SIP server lease 53
unregister on reboot 53
user ID, SIP 52
SIP registration 53
SIP remote SIP port 52
SIP server 52
password for login 52
SIP servers supported 5
unregister from 53
user ID for login 52
SIP volume 38
speaker output 6
SRST 53
subnet mask 29, 49
supported protocols 5
W
warranty policy at CyberData 105
web access password 29
web access username 29
web configuration log in address 33
web page
navigation 30
web page navigation 30
web-based intercom configuration 29
weight 6
wget, free unix utility 90
Windows, setting up a TFTP server on 103
wiring the circuit 17
devices less than 1A at 30 VDC 17
T
tech support 105
technical support, contact information 105
terminal block, 16 AWG gauge wire 14
TFTP server 5, 103
triggering a dial out call or security code 44
U
unit dimensions—front and side view 94
unit dimensions—rear view and mounting hole
locations 94
upgrading to firmware 6.x.x from 5.x.x 99
user ID
for SIP server login 52
username
changing for web configuration access 37
default for web configuration access 33
restoring the default 29
V
video parameters 45
video, field of view 13
VLAN ID 49
Operations Guide
931338D
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising