CyberData | 011477 | Owner Manual | Cyberdata ** NEW RELEASE ** 011477 SIP Outdoor Intercom with RFID Owner manual

Cyberdata ** NEW RELEASE ** 011477 SIP Outdoor Intercom with RFID Owner manual
Gooseneck Mounting
Installation Quick Reference
Apply RTV Silicone Sealant Around Mounting Holes and
Backside Perimeter of Backbox and Weather Shroud
Washer & Nut
J1
Carriage Bolt, Washer & Nut
(3 Sets Included)
The IP Endpoint Company
Cable & Wire
Create Service Loop
SIP Outdoor Intercom with RFID
Secure Access Control Endpoint
011477
to J1
Weather Shroud
(Sold Separately)
Parameter
Torx Key
Backbox
Apply RTV Silicone Sealant Around Mounting Holes and
Backside Perimeter of Backbox and Weather Shroud
1/4" Concrete
Wall Anchor
Faceplate Mounting
Torx Security Screw
Cable & Wire
Create Service Loop
SIP Outdoor Intercom
RFID Access Control Endpoint
J1
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
1/4"
Anchor Screw
Gooseneck
to J1
a
255.0.0.0
Default Gatewaya
Weather Shroud
(Sold Separately)
*
Factory Default Setting
10.0.0.1
a. Default if there is not a DHCP server present.
Torx Key
Network and Ground Wires in
Through Side Conduit Hole
Typical System Installation
Remove Hole Plug Assembly then
Install It onto Rear Conduit Hole
*
Faceplate Mounting
Torx Security Screw
*More installation and mounting
options are available in the
Operations Guide.
1/2" EMT
Compression
Connector
with
Sealing Locknut
(Sold Separately)
802.3af Compliant Ethernet Switch
Ground Wire
Network Cable
1/2" EMT
Conduit
*More installation and mounting information
is illustrated in the Operations Guide.
Endpoint
Endpoint
Endpoint
IP Phone
IP PBX Server
Getting Started
•
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011477
•
Create a plan for the locations of your devices.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
(1) Assembly
Contacting CyberData
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Accessory Kit
Optional Accessories
(1) 1/2-inch EMT
compression
connector with extra
sealing locknut
Carriage Bolt Bolts
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
931661A
(1) 531085* Hole
plug assembly
Mounting Component
Security Torx Key
Carriage Bolt Nuts
Accessory Kit Security Torx MS
Carriage Bolt Washers
Quick Reference
Quick Reference
931661A
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
Dimensions (Rear View and Mounting Holes)
Dimensions (Front and Side View)
7.008 [178.0]
3.380 [85.9]
Ground Lug Fits Size 8 Ring Terminal
Hex Nut Socket Size 5/16” or 8mm
Green LED
3.380 [85.9]
3.399 [86.3]
5.118 [130.0]
4.580 [116.3]
Conduit Hole Fits
1/2" EMT Compression Connector
Ø0.875 [Ø22]
5.118 [130.0]
Red LED Buzzer
RFID
Mounting Holes Fits
1/4" Screws
Ø0.280 [Ø7]
2.265 [57.5]
7.480 [190.0]
Dimensions are in Inches [Millimeter]
#6-32 Threads
Faceplate Mounting Holes
0.269 [6.8]
3.181 [80.8]
Terminal Block Connections
3.181 [80.8]
0.559 [14.2]
7.480 [190.0]
Dimensions are in Inches [Millimeter]; Projection: Third Angle.
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
Flange Flush Mount
Mounting Holes
Features
Side Conduit Hole
Ø0.875 [Ø22]
4
0.730 [18.5]
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
Wire (IN)
0.25"
Wall Mounting with Ground Cable and Network Cable Installation
1
J1
When the device is operational and linked to a
network, you can use the Reset Test Function
Management (RTFM) button (SW1 [see picture]) to restore the device to the factory
default settings.
To restore the device to factory default
settings:
•
The device will use DHCP to obtain
the new IP address (DHCP-assigned
address or default to 10.10.10.10 if a
DHCP server is not present).
Quick Reference
to J1
*
Network and Ground Wires in
Through Rear Conduit Hole
Weather Shroud
(Sold Separately)
Torx Key
1/4"
Anchor Screw
Backbox
Ground Wire
Network Cable
Backbox Mounting Holes Fits 1/4"
Concrete Anchor and Screw; Gound Lug Fits Size 8 Ring Terminal.
(All Mounting Hardwares and Cable Assemblies are Not Provided)
Faceplate Mounting
Torx Security Screw
Press and hold the RTFM button for
longer than five seconds.
Note
931661A
1/4" Concrete
Wall Anchor
Ground Wire to
Ground Lug
Terminal Block
can accept 16 AWG wire
SIP Outdoor Intercom
RFID Access Control Endpoint
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
https://www.cyberdata.net/products/011442
Apply RTV Silicone Sealant Around Mounting Holes and
Backside Perimeter of Backbox and Weather Shroud
RTFM Button
RTFM button (SW1)
Note: For flush mount installations, purchase the 011442 Flush
Mount Kit, 2x (sold separately). For more information, go to:
Note: To mount the device, use methods
compliant with local electrical codes.
Note: More installation and mounting information
is illustrated in the Operations Guide.
8
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
1.695 [43.1]
Caution
GENERAL ALERT
Quick Reference
Equipment Hazard: Do not use an electric or power screwdriver to fasten the face plate and PCB assembly to
the gang box. To prevent over-torque damage to the gasket, do not apply more than 10 inch-pounds force.
Over-torquing will cause the gasket to tear, risk moisture intrusion, and effectively void the manufacturer's
warranty.
931661A
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising