CyberData | 011211 | Quick Reference | Cyberdata 011211 SIP Indoor Intercom Quick Reference

Cyberdata 011211 SIP Indoor Intercom Quick Reference
Wall Mounting Options
Pre Drill Holes
(4 Places) on Wall
Installation Quick Reference
The IP Endpoint Company
Backplate
SIP Compliant
Cable
Slots
Closed
Pick One of Four Mounting Hole
for Ground Wire Connection
011211*, RAL 9003, Signal White
Wall
Cutout
Cable
Entry
Slot
VoIP V3 Indoor Intercom
*Replaces the 011111 number.
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Address
Network Cable &
Ground Wire
(Not Provided)
a
Web Access Username
admin
Web Access Password
admin
Subnet Mask
121001A
Screw
Accessory Kit
10.10.10.10
a
255.0.0.0
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
Getting Started
•
Mounting
Screw (3x)
Download the VoIP V3 Indoor Intercom Operations Guide PDF file from the following web page:
http://www.cyberdata.net/products/voip/digitalanalog/intercomindoorv3/docs.html
Gang Box Mounting Options
Wall Cutout
•
Create a plan for the locations of your Intercoms.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
(1) Intercom Assembly
Wall Cutout
(1) Wall Mounting Kit
(4) Sheet Metal Screw
(4) Plastic Ribbed Anchor
Cable
Slots
Closed
Backplate
(1) Gang Box Mounting Kit
(4) #6-32 FlatHead Countersunk
Machine Screw
Network Cable
(Not Provided)
Backplate accept
Single Gang Box
or Two Gang Box
Cable
Entry
Slot
Contacting CyberData
Ground Wire
(Not Provided)
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Ground Wire Connect to
Any Available Mounting Hole
Mounting
Screw (3x)
121002B
Screw Accessory Kit
Two Gang Box use four
Single Gang Box use two
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930502H
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Quick Reference
Quick Reference
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
930502H
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Cable Connections
RTFM Button
When the device is operational and linked to a network, you can
use the Reset Test Function Management (RTFM) button (SW1
[see picture]) to announce the device’s IP address or restore the
device to the factory
default settings.
SW1
To announce the device’s current IP address:
•
Press and release the RTFM button within a five second
window.
PCBA
021078D
Push-Button
to J2
Note
PCBA
Mounting
Screws
The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
•
Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
J2
Dimensions
J7
Back Plate
J6
Speaker to J7
Microphone
to J6
Mounting
Screws
4.53 [115.0]
Terminal Block Connections
4.53 [115.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
2.22 [56.3]
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Wire (IN)
Terminal Block
can accept
3
4
16 AWG wire
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
*Contacts 1 and 2 on the J3 terminal block are only
for powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
Maximum Recommended Wall Cutout Dimensions
0.25 [6.4]
Top Cable Entry Opening
0.25 [6.4]
1
6
J3 Terminal Block
Wall Cutout
0.25 [6.4]
0.25 [6.4]
Top Cable Entry Closed
Dimensions are in Inches [Millimeter]
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
930502H
Quick Reference
Quick Reference
930502H
© 2015, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising