CyberData | 011426 | Owner Manual | Cyberdata 011426 RFID/Keypad Secure Access Control Endpoint Owner manual

Cyberdata 011426 RFID/Keypad Secure Access Control Endpoint Owner manual
Installation Quick Reference
Connecting the Intercom (Service Loop Routing)
Ground Cable Installation
Network Cable Installation
Service Loop
1X Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
The IP Endpoint Company
Service Loop
Network
Cable
Ground
Wire
1X Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
Nut
011426
Gang Box
Gang Box
Ground Lug
Faceplate
Assembly
SIP RFID/Keypad Secure Access Control Endpoint
SIP Compliant
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Faceplate
Assembly
Typical System Installation
Securing the Intercom
*More installation and mounting
options are available in the
Operations Guide.
Caution
GENERAL ALERT
Equipment Hazard: Do not use an
electric or power screwdriver to fasten
the face plate and PCB assembly to
the gang box. To prevent over-torque
damage to the gasket, do not apply
more than 10 inch-pounds force.
Over-torquing will cause the gasket to
tear, risk moisture intrusion, and
effectively void the manufacturer's
warranty.
802.3af Compliant Ethernet Switch
1X Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
Endpoint
Endpoint
Endpoint
IP Phone
IP PBX Server
Getting Started
•
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011426
Note: To mount the device, use methods
compliant with local electrical codes.
Torx Key
Gang Box
Note: More installation and mounting
information is illustrated in the Operations
Guide.
Note: For flush mount installations, purchase the
011443 Flush Mount Kit, 1X (sold separately).
For more information, go to:
Faceplate
Assembly
•
Create a plan for the locations of your Intercoms.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
http://www.cyberdata.net/voip/011443/
(1) SIP RFID/
Keypad Secure
Access Control
Contacting CyberData
(1) T-15H Torx Key
Optional Accessories
(for gooseneck mounting)
Optional Accessories
(1) Spacer for half-inch set conduit connector
(4) Carriage bolt nuts
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
931419A
(4) Security Torx Screw
(4) Carriage bolts
(1) Hole plug assembly
(4) Carriage bolt washers
Quick Reference
Quick Reference
931419A
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Features
RTFM Button
Dimensions (Front and Side View)
Red LED
RTFM button (SW1)
4.000 [101.6]
5.118 [130.0]
5.198 [132.0] w/HOLE PLUG
Buzzer
Green LED
RFID
When the device is operational and linked to a
network, you can use the Reset Test Function
Management (RTFM) button (SW1 [see picture]) to restore the device to the factory
default settings.
To restore the device to factory default
settings:
• Press and hold the RTFM button for
longer than five seconds.
Note
Keypad
2.172 [55.2]
4.580 [116.3]
5.118 [130.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
The device will use DHCP to obtain
the new IP address (DHCP-assigned
address or default to 10.10.10.10 if a
DHCP server is not present).
Dimensions (Rear View and Mounting Holes)
Conduit Mounting (Side Entry)
5.1 [130]
4.6 [116]
4.0 [102]
*More installation and mounting
Hole Plug
information is illustrated in the
Assembly
Operations Guide.
Hole Plug [Washer]
#6-32
Threaded
ø0.3 [ø7]
(4 Places)
Gang Box
Assembly
[Nut]
Ground
Lug & Nut
3.4 [86]
Conduit
Hole
ø0.9 [ø22]
Conduit
Hole
ø0.9 [ø22]
1/2" Set Screw
Connector Nut
2.6 [65]
5.1 [129]
4.6 [116]
4.0 [102]
1/2" Set Screw
Connector Nut
Rotate Gang Box
for Desired Conduit
Exit Direction
Hole Plug
Assembly
[Hole Plug]
1/2" Set Screw
Connector
1/2" Conduit
3.4 [86]
DIMENSIONS ARE IN INCHES [MILLIMETER]
PROJECTION: THIRD ANGLE
Terminal Block Connections
1/2" Set Screw
Connector
Side View
Optional Gooseneck Mounting
4
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
Wire (IN)
0.25"
Hole Plug
Assembly
[Nut]
1
931419A
Hole Plug
Assembly
[Washer]
GOOSENECK
(NOT PROVIDED)
Gang Box
1/4" Round Head
Carriage Bolt (4x)
Weather Shroud
Part Number: 011188A
(SOLD SEPARATELY)
1X Faceplate
Mounting Screws
Flat Head Phillips or
Security Torx
8
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Fiber Washer
(As Spacer)
Fiber Washer
(As Spacer)
Gang Box
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
1/2" Conduit
0.7 [19]
GOOSENECK
[CUTAWAY VIEW
TO SHOW
CABLE ROUTING]
Hole Plug
Assembly
[Hole Plug]
(REMOVE HOLE PLUG ASSEMBLY
FROM 2-GANG BOX
BEFORE FASTEN IT TO SHROUD
AND/OR GOOSENECK; OR
CONDUIT HOLE WITH HOLE PLUG
FACING BOTTOM)
Nut for
Ground Lug
Faceplate
Assembly
Terminal Block
can accept 16 AWG wire
Quick Reference
1/4" Washer (4x)
1/4" Nut (4x)
Quick Reference
NETWORK &
GROUND CABLE
931419A
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising