CyberData | 011487 | Operations Guide | Cyberdata **NEW RELEASE** 011487 Multicast Wall Mount Speaker Operations Guide

Cyberdata **NEW RELEASE** 011487 Multicast Wall Mount Speaker Operations Guide
The IP Endpoint Company
Multicast Wall Mount
Speaker
Operations Guide
Part #011487
Document Part #931691B
for Firmware Version 1.1.1
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
SIP Speaker Operations Guide 931691B
Part # 011487
COPYRIGHT NOTICE:
© 2019, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
Operations Guide
931691B
CyberData Corporation
Revision Information
Revision 931691B, which corresponds to firmware version 1.1.1, was released on September 26,
2019, and has the following changes:
•
Updates Section 1.3, "Product Features"
•
Updates Table 1-1, "Product Specifications"
•
Updates Figure 2-16, "Multicast Page"
•
Updates Table 2-9, "Multicast Page Parameters"
Browsers Supported
The following browsers have been tested against firmware version 1.1.1:
Operations Guide
•
Internet Explorer (version: 11)
•
Firefox (also called Mozilla Firefox) (version: 62.0)
•
Chrome (version: 63.0.3239.132)
•
Safari (version: 12)
•
Microsoft Edge (version: 42.17134.1.0)
931691B
CyberData Corporation
Pictorial Alert Icons
GENERAL ALERT
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
Operations Guide
931691B
CyberData Corporation
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The Multicast Wall Mount Speaker enclosure is not rated for any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
Operations Guide
931691B
CyberData Corporation
Abbreviations and Terms
Operations Guide
Abbreviation or Term
Definition
A-law
A standard companding algorithm, used in European digital
communications systems to optimize, i.e., modify, the dynamic range of an
analog signal for digitizing.
AVP
Audio Video Profile
Cat 5
TIA/EIA-568-B Category 5
DHCP
Dynamic Host Configuration Protocol
LAN
Local Area Network
LED
Light Emitting Diode
Mbps
Megabits per Second.
NTP
Network Time Protocol
PBX
Private Branch Exchange
PoE
Power over Ethernet (as per IEEE 802.3af standard)
RTFM
Reset Test Function Management
SIP
Session Initiated Protocol
u-law
A companding algorithm, primarily used in the digital telecommunication
UC
Unified Communications
VoIP
Voice over Internet Protocol
931691B
CyberData Corporation
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical Configuration ................................................................................................................2
1.3 Product Features ......................................................................................................................3
1.4 Supported Protocols .................................................................................................................4
1.5 Product Specifications ..............................................................................................................5
1.6 Compliance ..............................................................................................................................6
1.6.1 CE Testing ......................................................................................................................6
1.6.2 FCC Statement ..............................................................................................................6
Chapter 2 Installing the Multicast Wall Mount Speaker
7
2.1 Parts List ..................................................................................................................................7
2.2 Device Configuration ................................................................................................................8
2.2.1 Connect Power to the Speaker ......................................................................................9
2.2.2 Confirm that the Speaker is Operational and Linked to the Network ..........................11
2.2.3 Confirm the IP Address and Test the Audio .................................................................12
2.2.4 How to Set the Factory Default Settings .......................................................................13
2.3.1 Factory Default Settings ...............................................................................................14
2.3.2 Multicast Wall Mount Speaker Web Page Navigation ..................................................15
2.3.3 Using the Toggle Help Button .......................................................................................16
2.3.4 Log in to the Configuration Home Page .......................................................................18
2.3.5 Configure the Device ....................................................................................................22
2.3.6 Configure the Network Parameters .............................................................................24
2.3.7 Configure the SSL Parameters ....................................................................................27
2.3.8 Configure the Multicast Parameters .............................................................................32
2.3.9 Configure the Audiofiles Page Parameters ...................................................................34
2.3.10 Configure the Events Parameters ..............................................................................38
2.3.11 Configure the Autoprovisioning Parameters ...............................................................43
2.4.1 Downloading the Firmware ...........................................................................................54
2.4.2 Reboot the Device ........................................................................................................57
2.5.1 Command Interface Post Commands ..........................................................................58
Appendix A Mounting the Speaker
60
A.1 Mounting ................................................................................................................................60
A.2 Dimensions ............................................................................................................................61
Appendix C Setting up a TFTP Server
62
C.1 Set up a TFTP Server ............................................................................................................62
C.1.1 Autoprovisioning requires a TFTP server for hosting the configuration file. .................62
C.1.2 In a LINUX Environment ..............................................................................................62
C.1.3 In a Windows Environment .........................................................................................62
Appendix C Troubleshooting/Technical Support
63
C.1 Frequently Asked Questions (FAQ) ........................................................................................63
C.2 Documentation .......................................................................................................................63
C.3 Contact Information ................................................................................................................64
C.4 Warranty and RMA Information ..............................................................................................64
Index
Operations Guide
65
931691B
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the Multicast Wall Mount Speaker, look for a model number label similar to the one shown 
in Figure 1-1. The model number on the label should be 011487.
Figure 1-1. Model Number Label
www.cyberdata.net
Multicast Wall Mount Speaker
011487* / 021538C
487000001
CAN ICES-3 (A)/NMB-3(A)
00:20:F7:03:83:CA
V 1.1.1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Model number
Operations Guide
Serial number begins with 487
931691B
CyberData Corporation
Product Overview 2
Typical Configuration
1.2 Typical Configuration
Figure 1-2 shows a typical configuration for the Multicast Wall Mount Speaker.
Figure 1-2. Typical Configuration
Operations Guide
931691B
CyberData Corporation
Product Overview 3
Product Features
1.3 Product Features
Operations Guide
•
Receives multicast messages
•
Supports audio prioritization for 10 multicast paging groups
•
Can receive pages directly from Poly phones as well as other devices that can send standard
multicast
•
Supports delayed pages with buffered multicast
•
Network-adjustable speaker volume
•
High efficiency speaker driver
•
Small footprint
•
TLS security for autoprovisioning and web-based configuration
•
802.11q VLAN tagging
•
Configurable event generation for device health and status monitoring
•
User upgradeable firmware via web interface or autoprovisioning
931691B
CyberData Corporation
Product Overview 4
Supported Protocols
1.4 Supported Protocols
The Multicast Wall Mount Speaker supports:
•
Multicast
•
HTTP Web-based configuration
Provides an intuitive user interface for easy system configuration and verification of speaker
operations.
•
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
•
HTTP TCP Post auto-updating event notification in XML format
•
TLS 1.2
•
TFTP Client
Facilitates hosting for the configuration file for Autoprovisioning.
•
Audio Encodings
PCMU (G.711 µ-law)
PCMA (G.711 a-law)
G.729
Operations Guide
931691B
CyberData Corporation
Product Overview 5
Product Specifications
1.5 Product Specifications
Table 1-1. Product Specifications
Category
Specification
Ethernet I/F
10/100 Mbps
Protocol
RTP
Power Input
PoE 802.3af
Audio Output
802.3af - SPL 98 dB @ 1 meter
Payload types
G.711 a-law, G.711µ-law, G.722 and G.729
Network Security
TLS/SSL 1.2
Operating Range
Temperature: -40o C to 55o C (-40o F to 131o F)
Humidity: 5-95%, non-condensing
Storage Temperature
-40o C to 70o C (-40o F to 158o F)
Storage Altitude
Up to 15,000 ft. (4573 m)
Dimensions
6.42 in. [163 mm] Length
5.39 in. [137 mm] Width
9.18 in. [233 mm] Height
Weight
3.8 lbs [1.72 kg]
Boxed Weight
4.4 lbs [1.96 kg]
Compliance
CE; EMC Directive - Class A EN 55032 & EN 55024, LV Safety Directive- EN 60950-1, RoHS
Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A, IEEE 802.3 Compliant
Warranty
2 Years Limited
Part number
011487
Operations Guide
931691B
CyberData Corporation
Product Overview 6
Compliance
1.6 Compliance
1.6.1 CE Testing
CE testing has been performed according to EN ISO/IEC 17050 for Emissions, Immunity, and Safety.
Note
You can download the Declaration of Conformity document from the Downloads tab of the
product’s webpage.
1.6.2 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Operations Guide
931691B
CyberData Corporation
2 Installing the Multicast Wall Mount
Speaker
2.1 Parts List
Table 2-1 illustrates the parts for each speaker and includes kits for the drop ceiling and drywall
mounting.
Note
The installation template for the Multicast Wall Mount Speaker is located on the Installation
Quick Reference Guide that is included in the packaging with each speaker.
Table 2-1. Parts
Quantity
Operations Guide
Part Name
Illustration
1
Multicast Wall Mount Speaker
Assembly
1
Installation Quick Reference Guide
931691B
CyberData Corporation
7
Installing the Multicast Wall Mount Speaker 8
Device Configuration
2.2 Device Configuration
Set up and configure each speaker before you mount it.
CyberData delivers each speaker with the following factory default values:
Table 2-2. Factory Network Default Settings—Default of Network
Parameter
Factory Default Setting
IP Addressing
DHCP
a
IP Address
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
Default
a
255.0.0.0
Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 9
Device Configuration
2.2.1 Connect Power to the Speaker
Figure 2-1 through Figure 2-2 illustrates how to connect power to the Multicast Wall Mount Speaker.
2.2.1.1 Multicast Wall Mount Speaker to a 802.3af Compliant PoE Switch
Figure 2-1 illustrates how to connect the Multicast Wall Mount Speaker to a 802.3af compliant PoE
switch via a Cat 5 Ethernet cable.
Figure 2-1. Multicast Wall Mount Speaker to a 802.3af Compliant PoE Switch
802.3af Compliant PoE Switch
Cat 5 Ethernet cable
Speaker
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 10
Device Configuration
2.2.1.2 Multicast Wall Mount Speaker (with PoE Injector) to a 802.3af Compliant PoE
Switch
In Figure 2-2, if a PoE switch is not available, you will need a PoE Injector, part #010867A (ordered
separately). A PoE Injector is a power supply solution for those who have a standard Non PoE
Switch.
Figure 2-2. Multicast Wall Mount Speaker (with PoE Injector) to a Non PoE Switch
Non PoE Switch
PoE Injector
Speaker
Cat 5 Ethernet cable
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 11
Device Configuration
2.2.2 Confirm that the Speaker is Operational and Linked to the Network
After connecting the speaker to the 802.3af compliant Ethernet hub, the LEDs on the speaker face
confirm that the speaker is operational and linked to the network.
Figure 2-3. Status and Activity LEDs
Network
100 Mb
(Yellow)
Speaker
Link/Activity
(Green)
2.2.2.1 Link/Activity LED
After supplying power to the speaker:
1. The green Link/Activity LED comes on immediately to show that there is a good network
connection, and then blinks to show network activity.
2. After about 23 seconds with a static IP address (or 27 seconds if the board is set to use DHCP),
the speaker should be ready.
Note
If the board is set to use DHCP and there is not a DHCP server available on the network, it
will try 12 times with a three second delay between tries and eventually fall back to the
programmed static IP address (by default 10.10.10.10). This process will take approximately
80 seconds.
2.2.2.2 100 Mb LED
•
Operations Guide
The yellow 100 Mb LED is illuminated when the network 100 Mb link to the speaker is
established.
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 12
Device Configuration
2.2.3 Confirm the IP Address and Test the Audio
2.2.3.1 Reset Test Function Management (RTFM) Button
When the speaker is operational and linked to the network, use the Reset Test Function
Management (RTFM) button (Figure 2-4) on the speaker face to announce and confirm the
speaker’s IP Address and test that the audio is working.
Figure 2-4. RTFM Button
RTFM button
To announce a speaker’s current IP address, use an instrument through the hole to press and
release the RTFM button within a five second window.
Operations Guide
Note
The speaker will use DHCP to obtain the new IP address (DHCP-assigned address or
default to 10.10.10.10 if a DHCP server is not present).
Note
Pressing and holding the RTFM button for longer than five seconds will restore the speaker
to the factory default settings.
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 13
Device Configuration
2.2.4 How to Set the Factory Default Settings
2.2.4.1 RTFM Button
When the speaker is operational and linked to the network, use the Reset Test Function
Management (RTFM) button (Figure 2-5) on the speaker face to set the factory default settings.
Figure 2-5. RTFM Button
RTFM button
To set the factory default settings:
1. Press and hold the RTFM button for more than five seconds.
2. The speaker announces that it is restoring the factory default settings.
Note
Operations Guide
The speaker will use DHCP to obtain the new IP address (DHCP-assigned address or
default to 10.10.10.10 if a DHCP server is not present).
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 14
Device Configuration
2.3 Configure the Multicast Wall Mount Speaker
Parameters
To configure the Multicast Wall Mount Speaker online, use a standard web browser.
Configure each Multicast Wall Mount Speaker and verify its operation before you mount it. When you
are ready to mount an Multicast Wall Mount Speaker, refer to Appendix A, "Mounting the Speaker"
for instructions.
2.3.1 Factory Default Settings
All Multicast Wall Mount Speakers are initially configured with the following default IP settings:
When configuring more than one Multicast Wall Mount Speaker, attach the Multicast Wall Mount
Speakers to the network and configure one at a time to avoid IP address conflicts.
Table 2-3. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 15
Device Configuration
2.3.2 Multicast Wall Mount Speaker Web Page Navigation
Table 2-4 shows the navigation buttons that you will see on every Multicast Wall Mount Speaker web
page.
Table 2-4. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Network page.
Link to the SSL page.
Link to the Multicast page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Autoprovisioning page.
Link to the Firmware page.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 16
Device Configuration
2.3.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-6 and Figure 2-7.
Figure 2-6. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-7.
Figure 2-7. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 17
Device Configuration
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-8.
), and a short description of the web
Figure 2-8. Short Description Provided by the Help Feature
Question mark
Operations Guide
931691B
A short description of the 
web page item will appear
CyberData Corporation
Installing the Multicast Wall Mount Speaker 18
Device Configuration
2.3.4 Log in to the Configuration Home Page
1. Open your browser to the Multicast Wall Mount Speaker IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Multicast Wall Mount Speaker.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
https://www.cyberdata.net/pages/discovery
Note
The device ships in DHCP mode. To get to the Home page, use the discovery utility to scan
for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-9):
Web Access Username: admin
Web Access Password: admin
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 19
Device Configuration
Figure 2-9. Home Page
487000001
v1.1.0
v1.1.0
v1.1.0
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 20
Device Configuration
3. On the Home page, review the setup details and navigation buttons described in Table 2-5.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-5. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
Partition 2
Contains a complete copy of bootable software.
Partition 3
Contains an alternate, complete copy of bootable software.
Booting From
Indicates the partition currently used for boot.
Allows the user to boot from the alternate partition.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Multicast Volume
Shows the current Multicast volume level.
Event Reporting
Shows the current status of the Event Reporting mode.
Import Settings
Use this button to select a configuration file to import.
After selecting a configuration file, click Import to import the
configuration from the selected file. Then, click Save and Reboot to
store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 21
Device Configuration
Table 2-5. Home Page Overview (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you will
see a question mark ( ) appear next to some of the web page items.
Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 22
Device Configuration
2.3.5 Configure the Device
1. Click the Device menu button to open the Device page. See Figure 2-10.
Figure 2-10. Device Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 23
Device Configuration
2. On the Device page, you may enter values for the parameters indicated in Table 2-6.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-6. Device Page Parameters
Web Page Item
Description
Volume Settings (0-9)
Multicast Volume
Set the speaker volume for multicast audio streams. A value of 0 will mute
the speaker during multicasts.
Note: You can change this setting without rebooting the device.
Clock Settings
Enable NTP
Sync device's local time with the specified NTP Server.
NTP Server
Use this field to set the address (in IPv4 dotted decimal notation or as a
canonical name) for the NTP Server. This field can accept canonical
names of up to 64 characters in length.
Timezone
Enter the tz database string of your timezone.
Examples:
America/Los_Angeles
America/New_York
Europe/London
America/Toronto
See https://en.wikipedia.org/wiki/List_of_tz_database_time_zones for
a full list of valid strings.
Current Time
Displays the current time.
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do not
recommend disabling HTTPS for security reasons.
Click on the Test Audio button to do an audio test. When the Test Audio
button is pressed, you will hear a voice message for testing the device
audio quality and volume.
Click the Save button to save your configuration settings.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 24
Device Configuration
2.3.6 Configure the Network Parameters
1. Click the Network menu button to open the Network page (Figure 2-11).
Figure 2-11. Network Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 25
Device Configuration
2. On the Network page, enter values for the parameters indicated in Table 2-7.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-7. Network Page Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking the
appropriate radio button. DHCP Addressing mode is enabled on default and
the device will attempt to resolve network addressing with the local DHCP
server upon boot. If DHCP Addressing fails, the device will revert to the last
known IP address or the factory default address if no prior DHCP lease was
established. See Section 2.3.1, "Factory Default Settings" for factory default
settings. Be sure to click Save and Reboot to store changes when configuring
a Static address.
Hostname
This is the hostname provided by the DHCP server. See the DHCP/DNS
server documentation for more information. Enter up to 64 characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal notation.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The switch port
connected to the device will need to be in “trunking mode” for the VLAN tags
to propagate.
VLAN Priority (0-7)
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of 0 may
cause the VLAN ID tag to be ignored.
Click the Save button to save your configuration settings.
Click on the Reboot button to reboot the system.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 26
Device Configuration
Table 2-7. Network Page Parameters (continued)
Web Page Item
Description
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question
mark ( ) appear next to some of the web page items. Move the mouse
pointer to hover over a question mark to see a short description of a specific
web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 27
Device Configuration
2.3.7 Configure the SSL Parameters
1. Click SSL menu button to open the SSL page (Figure 2-12).
Figure 2-12. SSL Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 28
Device Configuration
Figure 2-13. SSL Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 29
Device Configuration
2. On the SSL page, enter values for the parameters indicated in Table 2-8.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-8. SSL Page Parameters
Web Page Item
Description
Server CAs
Use this button to select a configuration file to import.
Click Browse to select a CA certificate to import. After selecting
a server certificate authority (CA), click Import CA Certificate to
import it to the list of trusted CAs. CAs are used to validate the
certificate presented by the server when establishing a TLS
connection.
Restore Defaults will restore the default list of registered CAs
and Remove All will remove all registered CAs.
Restore Defaults will restore the default list of registered CAs
and Remove All will remove all registered CAs.
Client Certificate
When doing mutual authentication this device will present a client
certificate with these parameters.
Client CA
Right click and Save Link As... to get the Cyberdata CA used to
sign this client certificate.
Test SSL Connection
Server
The ssl test server address as a fully qualified domain name or in
IPv4 dotted decimal notation.
Port
The ssl test server port. The supported range is 0-65536.
Use this button to test a TLS connection to a remote server. This
will attempt to make a socket connection to the configured test
server and port and report the success or failure. This can be
used to debug TLS connection issues.
List of Trusted CAs
Provides details of the certificate. After clicking on this button, the
Certificate Info Window appears. See Section 2.3.7.1,
"Certificate Info Window".
Removes this certificate from the list of trusted certificates. After
clicking on this button, the Remove Server Certificate Window
appears. See Section 2.3.7.2, "Remove Server Certificate
Window".
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 30
Device Configuration
2.3.7.1 Certificate Info Window
The Certificate Info Window provides details of the certificate. This window appears after clicking
on the Info button. See Figure 2-14.
Figure 2-14. Certificate Info Window
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 31
Device Configuration
2.3.7.2 Remove Server Certificate Window
The Remove Server Certificate Window will ask if the user wants to remove a certificate from the
list of trusted certificates. This window appears after clicking on the Remove button. See Figure 215.
Figure 2-15. Remove Server Certificate Window
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 32
Device Configuration
2.3.8 Configure the Multicast Parameters
The Multicast page allows the device to join up to ten paging zones for receiving ulaw/alaw encoded
RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3.
1. Click on the Multicast menu button to open the Multicast page. See Figure 2-16.
Figure 2-16. Multicast Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 33
Device Configuration
2. On the Multicast page, enter values for the parameters indicated in Table 2-9.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed..
Table 2-9. Multicast Page Parameters
Web Page Item
Description
Priority
Indicates the priority for the multicast group. Priority 9 is the highest (emergency
streams). 0 is the lowest (background music).
Address
Enter the multicast IP Address for this multicast group (15 character limit).
Port
Enter the port number for this multicast group (5 character limit [range can be from
2000 to 65535]).
Note: The multicast ports have to be even values. The webpage will enforce this
restriction.
Name
Assign a descriptive name for this multicast group (25 character limit).
Buffer
Device will buffer up to four minutes of audio (length varies with codec) and then
play back the recording after the multicast stream finishes or after the buffer is full.
Beep
When selected, the device will play a beep before multicast audio is sent.
Polycom Default Channel
When a default Polycom channel/group number is selected, the device will
subscribe to the default channel for one-way group pages. Group Numbers 1-25
are supported. Or, select Disabled to disable this channel.
Polycom Priority Channel
When a priority Polycom channel/group number is selected, the device will
subscribe to the priority channel for one-way group pages. Group Numbers 1-25
are supported. Or, select Disabled to disable this channel.
Polycom Emergency Channel
When an emergency Polycom channel/group number is selected, the device will
subscribe to the default channel for one-way group pages. Group Numbers 1-25
are supported. Or, select Disabled to disable this channel.
Click the Save button to save your configuration settings.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question mark
( ) appear next to some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web page item.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 34
Device Configuration
2.3.9 Configure the Audiofiles Page Parameters
The Audiofiles page is used to add custom audio to the board. User uploaded audio will take
precedence over the audio files shipped with the device.
1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-17).
Figure 2-17. Audiofiles Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 35
Device Configuration
2. On the Audiofiles page, enter values for the parameters indicated in Table 2-10.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-10. Audiofiles Page Parameters
Web Page Item
Description
Available Space
Shows the space available for the user to save custom audio files if they want to change the
message when the door or sensor is triggered.
Audio Files
0-9
The name of the audio configuration option is the same as the spoken audio that plays on
the board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
Dot
Corresponds to the spoken word “dot.” (24 character limit)
Audio Test
Corresponds to the message “This is the CyberData IP speaker test message...” (24
character limit)
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Restoring Default
Corresponds to the message “Restoring default” (24 character limit).
Click on the Browse button to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the
file by using the Browse button. The Save button will delete any pre-existing user-uploaded
audio files.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 36
Device Configuration
2.3.9.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-18 through
Figure 2-20.
Figure 2-18. Audacity 1
Figure 2-19. Audacity 2
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 37
Device Configuration
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-20. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 38
Device Configuration
2.3.10 Configure the Events Parameters
The Events page specifies a remote server that can be used to receive HTTP POST events when
actions take place on the board.
1. Click on the Events menu button to open the Events page (Figure 2-21).
Figure 2-21. Events Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 39
Device Configuration
2. On the Events page, enter values for the parameters indicated in Table 2-11.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-11. Events Page Parameters
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote
server and port number whenever a certain action takes place.
Select an event type below to generate an HTTP POST event.
Events
Enable Multicast Start Events
When selected, the device will report when the device starts playing
a multicast audio stream.
Enable Multicast Stop Events
When selected, the device will report when the device stops playing
a multicast audio stream.
Enable Power On Events
When selected, the device will report when it boots.
Enable 60 Second Heartbeat
When enabled, the device will report a Heartbeat event every 60
seconds. SIP registration is not required to generate Heartbeat
events.
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 065536. Enter up to 5 digits.
Server URL
Generally, the destination URL is the name of the application that
receives the events and the string in the HTTP POST command. It
can be a script used to parse and process the HTTP POST events.
Enter up to 127 characters.
Click the Save button to save your configuration settings.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question mark
to see a short description of a specific web page item.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 40
Device Configuration
2.3.10.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 41
Device Configuration
User-Agent: CyberData/1.1.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 42
Device Configuration
User-Agent: CyberData/1.1.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.1.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 43
Device Configuration
2.3.11 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-22.
Figure 2-22. Autoprovisioning Page
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 44
Device Configuration
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 212.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-12. Autoprovisioning Page Parameters
Web Page Item
Description
Enable Autoprovisioning
The device will automatically fetch a configuration file, also known as the
'autoprovisioning file', based on the configured settings below.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename. The default
autoprovisioning filename is in the format of <mac address>.xml.
Supported filename extensions are .txt, and .xml. The current filename is denoted
by an asterisk at the bottom of the Autoprovisioning Page. Enter up to 256
characters.
A file may have any name with an xml extension. If a file name is entered, the
device will look for the specified file name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download autoprovisioning files.
Verify Server Certificate
When using ssl to download autoprovisioning files, reject connections where the
server address doesn't match the server certificate's common name.
Username
The username used to authenticate with an autoprovisioning server. Leave this
field blank to disable authentication.
Password
The password used to authenticate with an autoprovisioning server. Leave this field
blank to disable authentication.
Autoprovisioning Autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before checking for new
autoprovisioning files. Enter up to 6 digits. A value of 0 will disable this option.
Autoprovision at time (HHMMSS)
The time of day the device will check for a new autoprovisioning file. The time must
be 6 characters in length and in HHMMSS format. An empty value will disable this
option.
Autoprovision when idle
(in minutes > 10)
The idle time (in minutes greater than 10) after which the device will check for a
new autoprovisioning file. Enter up to 6 digits. A value of 0 will disable this option.
Click the Save button to save your configuration settings.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question mark
( ) appear next to some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web page item.
Press the Download Template button to create an autoprovisioning file for the
device. See Section 2.3.11.3, "Download Template Button"
Autoprovisioning log
Operations Guide
The autoprovisioning log provides information about the latest autoprovisioning
attempt (i.e. dhcp options and server accessed and files parsed or not found).
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 45
Device Configuration
Note
You must click on the Save button for the changes to take effect.
2.3.11.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.3.11.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-12). This file contains every configuration option that can
be set on the board.
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData VoIP Device</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
<!-<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<!-<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<!-<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 46
Device Configuration
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 47
Device Configuration
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-13. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 48
Device Configuration
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 49
Device Configuration
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 50
Device Configuration
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 51
Device Configuration
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 52
Device Configuration
2.3.11.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 53
Device Configuration
2.3.11.3 Download Template Button
The Download Template button allows the user to generate, download, edit, and then store an
autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Download Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-23). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-23.
Figure 2-23. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 54
Device Configuration
2.4 Upgrade the Firmware and Reboot the Multicast Wall
Mount Speaker
2.4.1 Downloading the Firmware
To download the firmware to your computer:
1. Download the latest firmware file from the Downloads tab at the following webpage:
http://www.cyberdata.net/products/011487/
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the Multicast Wall Mount Speaker home page as instructed in Section 2.3.4, "Log in to
the Configuration Home Page".
4. Click on the Firmware menu button to open the Firmware page. See Figure 2-24.
Caution
GENERAL ALERT
Equipment Hazard: CyberData strongly recommends that you first reboot the
device before attempting to upgrade the firmware of the device. See Section 2.4.2,
"Reboot the Device".
Figure 2-24. Firmware Page
5. Click on the Browse button, and then navigate to the location of the firmware file.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 55
Device Configuration
6. Select the firmware file. This reveals the Upload button (Figure 2-25).
Figure 2-25. Upload Button
Upload button
Status Messages
Upload Post Processing bar
Upload Progress bar
7. Click on the Upload button. After selecting the Upload button, you will see the progress of the
upload in the Upload Progress bar.
8. When the upload is complete, you will see the words Upload finished under Status Messages.
9. At this point, you will see the progress of the upload’s post processing in the Upload Post
Processing bar.
Note
Do not reboot the device before the upgrading process is complete.
10. When the process is complete, you will see the words SWUPDATE Successful under Status
Messages.
11. The device will reboot automatically.
12. The Home page will display the version number of the firmware and indicate which boot
partition is active.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 56
Device Configuration
Table 2-14 shows the web page items on the Firmware page.
Table 2-14. Firmware Page Parameters
Web Page Item
Description
Use the Browse button to navigate to the location of the Intercom firmware file
that you want to upload.
Click on the Upload button to automatically upload the selected firmware and
reboot the system.
Note: This button only appears after the user has selected a firmware file.
Upload progress
Status bar indicates the progress in uploading the file.
Upload Post Processing
Status bar indicates the progress of the software installation.
Status Messages
Messages relevant to the firmware update process appear here.
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 57
Device Configuration
2.4.2 Reboot the Device
To reboot a Multicast Wall Mount Speaker, log in to the web page as instructed in Section 2.3.4, "Log
in to the Configuration Home Page".
1. Click on the Reboot button on the Home page (Figure 2-26). A normal restart will occur.
Figure 2-26. Home Page
487000001
v1.1.0
v1.1.0
v1.1.0
Reboot
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 58
Device Configuration
2.5 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-15 use the free unix utility, wget, but any program that can send http POST
commands to the device should work.
2.5.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-15. Command Interface Post Commands
Device Action
HTTP Post Commanda
Reboot
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=reboot"
Test Audio
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=test_audio"
Speak IP Address
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=speak_ip_address"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "0=Play"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "1=Play"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "2=Play"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "3=Play"
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "4=Play"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "5=Play"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "6=Play"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "7=Play"
Operations Guide
931691B
CyberData Corporation
Installing the Multicast Wall Mount Speaker 59
Device Configuration
Table 2-15. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "8=Play"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "9=Play"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "d=Play"
Play the Audio Test
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "audiotest=Play"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "pagetone=Play"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "youripaddressis=Play"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "rebooting=Play"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate "https://10.10.1.138/audiofiles/" --quiet -O
/dev/null --post-data "restoringdefault=Play"
Swap boot partitions
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null --no-check-certificate "https://10.10.1.154/command" -post-data "request=swap_boot_partition"
a.Type and enter all of each http POST command on one line.
Operations Guide
931691B
CyberData Corporation
Appendix A: Mounting the Speaker
A.1 Mounting
See Figure A-1 for instructions on how to mount the speaker.
Figure A-1. Mounting the Speaker
Swivel Mount
Range of Motion
Long
Bolt
Approx.
200°
Keyhole
Universal
Joint
Base
Mount
Long
Bolt
Short
Bolt
Operations Guide
Base
Mount
Approx.
200°
931691B
CyberData Corporation
60
61
Dimensions
A.2 Dimensions
Figure A-2 shows the dimensions for the Multicast Wall Mount Speaker.
Figure A-2. Dimensions
1.657 [42.1]
Ø0.175 [Ø4.4]
Keyhole Mounting
Ø0.340 [Ø8.6]
Swivel Mount
Mounting Bracket
9.178 [233.1]
6.419 [163.0]
Operations Guide
5.396 [137.0]
931691B
Dimensions are in Inches [Millimeter]
Keyhole Fits Size #6 / 4mm Screw
CyberData Corporation
62
Appendix C: Setting up a TFTP Server
C.1 Set up a TFTP Server
C.1.1 Autoprovisioning requires a TFTP server for hosting the configuration
file.
C.1.2 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
C.1.3 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
https://www.cyberdata.net/pages/solarwinds
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
931691B
CyberData Corporation
63
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
To see a list of frequently asked questions for your product, click on the FAQs tab at the following
webpage:
http://www.cyberdata.net/products/011487/
C.2 Documentation
The documentation for this product is released in an English language version only.
To download PDF copies of CyberData product documentation, click on the Downloads tab at the
following webpage:
http://www.cyberdata.net/products/011487/
Operations Guide
931691B
CyberData Corporation
64
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601, Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Extension 333
C.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
Operations Guide
931691B
CyberData Corporation
65
Index
username and password 8, 14
web login username and password 18
default gateway 8, 14, 25
default IP settings 14
default login address 18
device configuration 8, 22
device configuration parameters 44
the device configuration page 43
device configuration page 22
device configuration parameters 23
device configuration password
changing for web configuration access 22
dimensions 5
discovery utility program 18
DNS server 25
download autoprovisioning template button 44
A
address, configuration login 18
adjusting volume 13
announcing a speaker’s IP address 12, 13
audio configuration 34
audio configuration page 34
audio files, user-created 36
audio output 5
audio test 12, 13
autoprovision at time (HHMMSS) 44
autoprovision when idle (in minutes > 10) 44
autoprovisioning 44, 45
download template button 44
autoprovisioning autoupdate (in minutes) 44
autoprovisioning configuration 43, 44
autoprovisioning filename 44
autoprovisioning server (IP Address) 44
E
export settings 20
C
changing
the web access password 22
command interface 58
commands 58
configurable parameters 23, 25
configuration
audio 34
default IP settings 14
device 8
door sensor 27
intrusion sensor 27
network 24
configuration home page 18
configuration page
configurable parameters 23, 25
confirming IP address 12, 13
contact information 64
contact information for CyberData 64
current network settings 25
CyberData contact information 64
F
factory default settings
how to set 13
features 3
firmware
where to get the latest firmware 54
G
get autoprovisioning template 44
H
home page 18
http POST command 58
D
I
default
gateway 8, 14
IP address 8, 14
subnet mask 8, 14
Operations Guide
identifying your product 1
import settings 20
import/export settings 20
931691B
CyberData Corporation
66
IP address 8, 14, 25
IP addressing
default
IP addressing setting 8, 14
L
Linux, setting up a TFTP server on 62
log in address 18
M
MGROUP
MGROUP Name 33
multicast configuration 32, 34
Multicast IP Address 33
N
navigation (web page) 15
navigation table 15
network configuration 24
network link activity, verifying 11
Nightringer 53
NTP server 23
O
overview 1
P
password
login 18
restoring the default 8, 14
polycom default channel 33
polycom emergency channel 33
polycom priority channel 33
POST command 58
power, connecting to speaker 9
product
parts list 7
product features 3
product overview 1
product features 3
product specifications 5
product specifications 5
Operations Guide
931691B
CyberData Corporation
67
R
reboot 56, 57
Reset Test Function Management (RTFM) button 12, 13
restoring the factory default settings 13
RTFM button 12, 13
S
sales 64
sensor setup page 27
sensor setup parameters 27
service 64
subnet mask 8, 14, 25
T
tech support 64
technical support, contact information 64
testing audio 12, 13
TFTP server 62
U
username
changing for web configuration access 22
default for web configuration access 18
restoring the default 8, 14
V
verifying
network link and activity 11
power on to speaker 11
VLAN ID 25
VLAN Priority 25
VLAN tagging support 25
VLAN tags 25
volume
multicast volume 23
volume, adjusting 13
W
warranty policy at CyberData 64
web access password 8, 14
web access username 8, 14
Operations Guide
931691B
CyberData Corporation
68
web configuration log in address 18
web page
navigation 15
web page navigation 15
wget, free unix utility 58
Windows, setting up a TFTP server on 62
Operations Guide
931691B
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising