CyberData | 011394 | Quick Reference | Cyberdata 011394/011393 SIP Speaker Quick Reference

Cyberdata 011394/011393 SIP Speaker Quick Reference
Installation Quick Reference
The IP Endpoint Company
SIP Speaker
SIP Compliant
011393*, RAL 9002, Gray White
011394*, RAL 9003, Signal White
120°
*Replaces the 011098 and 011099 numbers.
VoIP Speaker
Mounting Template
Speaker Hole Diameter:
7.50 [190.5]
Screw Hole Diameter:
0.1875 [4.75]
Parameter
Factory Default Setting
IP Addressing
IP Address
DHCP
a
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
Dimensions are in inches [millimeter]
Typical System Installation
*More installation options are
illustrated in the Operations Guide.
Speaker
802.3af/at Compliant Ethernet Switch
Speaker
Clock Kit
IP Phone
IP PBX Server
Getting Started
•
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011393-011394
4.00 [101.6]
•
Create a plan for the locations of your SIP Speakers.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
(1) Speaker Assembly
(1) Template for Speaker
and Screw Holes*
(1) Drop Ceiling Mounting Kit
(3) #8 Nylon Thumb Nuts
(1) Drywall Mounting Kit
(3) Plastic Ribbed Anchors
(3) #8 Fender Washers
(3) #8 Sheet Metal Screws
* See the last page
of this document
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
931180E
Quick Reference
Quick Reference
(3) 8-32 x 1 1/4” Mounting
Screws
931180E
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
Dimensions and Connections
Mounting
Tools Required for Installation:
Dry Wall Mounting Kit
Plastic Ribberd Anchor (3x)
AUX POWER (+)
(+24VDC @ 1A)
#8 Nylon Thumb Nut (3x)
#8 Fender Washer (3x)
AUX SPEAKER (-)
AUX SPEAKER (+)
GND
LINE OUT (-)
LINE OUT (+)
AUX POWER (-)
RELAY COM
RELAY NO
+5V OUT
N/C
*Ceiling Tile or Dry Wall
*Ceiling Tile
or Dry Wall
*Optional
Mount
*Optional Reinforcement
Reinforcement Mount
P/N:
P/N:010991
010991A(sold
(Sold separately)
Seperately)
(1) Sheetrock saw or
(1) Drywall cutter
•
(1) #2 Phillips Screwdriver or
(1) #2 Phillips Screwdriver Hex Bit
To mount a speaker:
1. Use the TEMPLATE on the back of this
document to cut a hole in the wall or
ceiling, and prepare holes for the screws.
N/C
J10
•
J9
Template
2. Plug the Ethernet cable into the speaker
assembly. The yellow light verifies the
network connection.
CLASS II WIRING
9.000 [228.60]
9.000
[228.60]
DIMENSIONS ARE IN INCHES [MILLIMETER]
DIMENSIONS ARE IN INCHES [MILLIMETER]
3.140 [79.75]
3.140
[79.75]
Connecting Power
PoE Injector
(part #011124)
Non PoE Switch
3. For drop ceiling mounting, position the IP
SPEAKER ASSEMBLY in the ceiling so
that its screw holes align with those you
prepared.
Speaker
VoIPAssembly
V3 Speaker
Assembly
4. For drywall mounting, place the three
PLASTIC RIBBED ANCHORS in the
holes you prepared, and position the IP
SPEAKER ASSEMBLY over them,
aligning the screw holes in the assembly
with the anchors.
Dry Wall Mounting Kit
#6 Screw (3x)
802.3af/at Compliant Ethernet Switch
Ceiling Mounting Screw
#8-32x1 1/4" (3X)
5. For drop ceiling mounting*, use the three
8-32 x 1 1/4" MOUNTING SCREWS, #8
NYLON THUMB NUTS, and #8
FENDER WASHERS to secure the
speaker.
For drywall mounting, use the three #8
SHEET METAL SCREWS to secure the
speaker.
Features
* For weak ceiling tile, CyberData offers a
reinforcing mount (CyberData part
number 010991).
Network Link/Activity LED (yellow)
Speaker Status LED (green)
A solid light confirms that the speaker is operational.
Contacting CyberData
Speaker Volume
Corporate Headquarters
RTFM Switch
To broadcast a device’s current IP address, press and
release the RTFM switch within a five second window.
To restore a device’s factory default settings, press and
hold the RTFM switch for more than five seconds.
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
931180E
Quick Reference
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Quick Reference
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
931180E
© 2019, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising