Cyberdata 011216 SIP Office Ringer Quick Reference
Add to my manuals2 Pages
CyberData 011216 is a SIP Office Ringer designed for use in VoIP phone systems. It offers a range of features to enhance communication and productivity in office environments. With PoE (Power over Ethernet) capability, it eliminates the need for a separate power adapter, simplifying installation and reducing cable clutter. The device supports DHCP for automatic IP address assignment, making network configuration hassle-free. It also features a built-in RTFM (Reset Test Function Management) button for easy IP address announcement or factory reset.
advertisement
▼
Scroll to page 2
Wall Mounting Options Installation Quick Reference Pre Drill Holes (4 Places) on Wall The IP Endpoint Company Backplate Cable Slots Closed Pick One of Four Mounting Hole for Ground Wire Connection SIP Office Ringer SIP Compliant Wall Cutout 011216 Cable Entry Slot Parameter Network Cable & Ground Wire (Not Provided) Factory Default Setting IP Addressing DHCP a 121001A Screw Accessory Kit IP Address 10.10.10.10 Web Access Username admin Web Access Password admin a 255.0.0.0 Subnet Mask Mounting Screw (3x) a 10.0.0.1 Default Gateway a. Default if there is not a DHCP server present. Gang Box Mounting Options Typical System Installation *More installation and mounting options are available in the Operations Guide. 802.3af Compliant Ethernet Switch Cable Slots Closed Backplate SIP Office Ringer SIP Office Ringer Wall Cutout Network Cable (Not Provided) SIP Office Ringer IP Phone IP PBX Server Backplate accept Single Gang Box or Two Gang Box Cable Entry Slot Getting Started Wall Cutout • Ground Wire (Not Provided) https://www.cyberdata.net/products/011216 Ground Wire Connect to Any Available Mounting Hole Mounting Screw (3x) 121002B Screw Accessory Kit Single Gang Box use two Two Gang Box use four Contacting CyberData Phone: 831-373-2601 Fax: 831-373-4193 http://www.cyberdata.net/ © 2018, CyberData Corporation, ALL RIGHTS RESERVED • Create a plan for the locations of your Office Ringers. • WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes. • WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. • WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant. • WARNING: This enclosure is not rated for any AC voltages! Parts Corporate Headquarters CyberData Corporation 3 Justin Court Monterey, CA 93940, USA Download the Operations Guide PDF file, from the Downloads tab at the following webpage: (1) Office Ringer Assembly Sales: (831) 373-2601 ext. 334 Support: 831-373-2601 ext. 333 Support Website: http://support.cyberdata.net/ RMA Department: (831) 373-2601 ext. 136 RMA Email: [email protected] RMA Status: http://support.cyberdata.net/ Warranty Information: http://support.cyberdata.net/ 931558A (1) Wall Mounting Kit (1) Gang Box Mounting Kit (4) #6 x 1.25-inch Sheet Metal Screw Quick Reference Quick Reference (4) Plastic ribbed anchor 931558A (4) 6-32 x 0.5-inch flat undercut Phillips machine screw © 2018, CyberData Corporation, ALL RIGHTS RESERVED RTFM Button Dimensions RTFM button (SW1) When the device is operational and linked to a network, you can use the Reset Test Function Management (RTFM) button (SW1 [see picture]) to announce the device’s IP address or restore the device to the factory default settings. To announce the device’s current IP address: • Press and release the RTFM button within a five second window. Note The device will use DHCP to obtain the new IP address (DHCP-assigned address or default to 10.10.10.10 if a DHCP server is not present). 4.53 [115.0] To restore the device to factory default settings: • Press and hold the RTFM button for longer than five seconds until you hear the device announce that it is restoring the factory default settings. Terminal Block Connections Alternate Power Input: 1 = +8 to +12VDC @ 1000mA Regulated Power Supply* 2 = Power Ground* 2.14 [54.3] 3 4.53 [115.0] DIMENSIONS ARE IN INCHES [MILLIMETER] Dimensions for Wall Mounting and One / Two Gang Box Mounting * Ø0.188 [Ø4.8] Through Hole 82° Countersunk (6 Places) 0.910 [23.1] screwdriver for the terminal block screws Wire (IN) Tin Leads Approx. 1/4” or 6mm 4 Relay Contact: (1 A at 30 VDC for continuous loads) 3 = Relay Common 4 = Relay Normally Open Contact 5 = Sense Input 6 = Sense Ground 7 = Remote Switch "A" 8 = Remote Switch "B" 1 8 *Contacts 1 and 2 on the terminal block are only for powering the device from a non-PoE 12VDC power source as an alternative to Network PoE power. Use of these contacts for any other purpose will damage the device and void the product warranty. Ø0.189 [Ø4.8] Through Hole (4 Places) * Terminal Block can accept 16 AWG wire Plug in the Network Cable and Create Service Loop Two (2) Cable Entry Slot When Use in Conjunction with Auxiliary Strobe P/N: 011288A (Sold Separately) 3.400 [86.4] 2.895 [73.5] 3.280 [83.3] * Fits One/Two Gang Box Use a 3.17 mm (1/8-inch) flat blade Cut Hole for Cable Through Two (2) Cable Entry Slot Network Cable Create Service Loop Before Closing Mounting Screw (3x) Faceplate Assembly 3.150 [80.0] Network Connector 1.820 [46.2] 3.400 [86.4] Dimensions Are in Inch [Millimeter] One (1) Cable Entry Slot = Slot Open = Slot Close Backplate © 2018, CyberData Corporation, ALL RIGHTS RESERVED 931558A Quick Reference Quick Reference 931558A © 2018, CyberData Corporation, ALL RIGHTS RESERVED
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project