CyberData | 011404 | Owner Manual | Cyberdata 011404 SIP Loudspeaker Amplifier (AC-Powered) Owner manual

Cyberdata 011404 SIP Loudspeaker Amplifier (AC-Powered) Owner manual
Installation Quick Reference
Mounting the Enclosure
To mount the enclosure:
The IP Endpoint Company
1. Prepare holes for the screws.
2. Plug in the power adapter and use the
Power (PWR) LED to verify that the
power is on.
SIP Loudspeaker Amplifier
SIP Compliant
3. Plug the ethernet cable into the device.
The Link/Activity (Link/Act.) LED
verifies the network connection.
Factory Default Setting
IP Addressing
IP Address
4. For wall mounting, use the three
#8 x 1-1/4-inch Pan Head Phillips
Self-Tapping Screws.
Web Access Username
Web Access Password
Subnet Maska
Default Gateway
a. Default if there is not a DHCP server present.
Getting Started
Download the SIP Loudspeaker Amplifier Operations Guide PDF file from the Documents tab at the following webpage:
Create a plan for the locations of your paging amplifiers.
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
WARNING: The SIP Loudspeaker Amplifier enclosure is not rated for any AC voltages!
Wiring the 125V AC Plug
The green wire with the yellow stripe is a ground connection for electrostatic discharge (ESD) protection,
and should not be removed.
To wire the 125V AC plug, consult a licensed electrician and the local building codes in your area.
(1) Assembly
(1) Wall Mounting Kit
(3) #8 Plastic Anchors
(3) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
Contacting CyberData
(1) Enclosure
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website:
RMA Department: (831) 373-2601 ext. 136
RMA Email:
RMA Status:
Warranty Information:
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Additional Parts
(1) CAT 5e/CAT6 cable
Quick Reference
Quick Reference
(1) PoE Power Injector
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Dimensions and Mounting Template
RTFM Switch
6.281 [159.54]
Dimensions are in Inches [Millimeters]
To broadcast the device’s current IP address, press and hold the RTFM switch for a couple
of seconds and then release it.
To restore the factory defaults, complete the following steps:
1. Press and hold the RTFM switch until you hear the device announce the words,
“restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the factory default settings.
Speaker Volume
The Speed (SPD) LED illuminates AMBER for a 100Mb link
or is off for a 10MB link when the network link to the device is established.
SPD Link/Act.
Link/Activity (Link/Act.) LED (GREEN)
The GREEN Link/Activity (Link/Act.) LED blinks to indicate network traffic.
PWR Status
Status LED (GREEN)
The GREEN Status LED illuminates after supplying power to the device.
The Power (PWR) LED is GREEN in low power mode (802.3af)
and BLUE during high power mode (802.3at).
10.875 [276.23]
Dimensions are in Inches [Millimeters]
*See the Operations Guide for more information about the features in this section.
Cable Grommets (3 PLCS)
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Quick Reference
Quick Reference
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF