CyberData | 011405 | Quick Start Guide | Cyberdata 011405 SIP Loudspeaker Amplifier (PoE) Quick Start Guide

Cyberdata 011405 SIP Loudspeaker Amplifier (PoE) Quick Start Guide
The IP Endpoint Company
SIP Loudspeaker Amplifier (PoE)
Quick Start Guide
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operations Guide,
which is available in the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011405/
Note
You can also navigate to the Downloads tab by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
1 A OUR PRODUCTS
2
B VOIP PRODUCTS
3
011405 SIP LOUDSPEAKER
AMPLIFIER-PoE
SIP
4
Downloads
2.0 Select Power Source
IEEE 802.3af or 802.3at PoE Switch
IEEE 802.3af or 802.3at PoE Injector
Set PoE power type to Class 0 = 15.4W
CAT6 cable recommended—
for longer distances
OR
for high power PoE+ set Class 4 = 30W
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
Quick Start Guide
931235A
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of
the device during the initialization process. See the following figure:
Volume
Speed (SPD) LED
(AMBER) (100Mb)
Power (Pwr) LED
(BLUE/GREEN)
SPD Link/Act
PWR
Status
Link/Activity (Link/Act.) LED
(GREEN)
Status LED
(GREEN)
3.2. The Power (Pwr) LED is GREEN for 802.3af and is BLUE for 802.3at. The
GREEN Status LED and the GREEN Power (Pwr) LED come on
immediately. The Speed (SPD) LED illuminates AMBER for a 100Mb link or
is off for 10MB when the network link to the device is established. The Link/
Activity LED blinks to indicate network traffic.
After about 20 seconds, the GREEN Status LED will blink fast to indicate
that the device is acquiring an IP address and attempting to autoprovision.
It will turn off thereafter until the device has finished booting. When the
device has fully booted, the GREEN Status LED will turn on solid.
If there is no DHCP server available on the network, it will try 12 times for 60
seconds and eventually fall back to the programmed static IP address (by
default 10.10.10.10) or the previously used DHCP address if a prior lease
was established. This process will take approximately 80 seconds.
3.3. When the device has completed the initialization process, press and hold
the RTFM switch for 3 seconds to announce the IP address.
This concludes the power test. Go to Section 4.0, "Connecting to a Network
in a Test Environment".
Quick Start Guide
931235A
4.0 Connecting to a Network in a Test Environment
Note
The following connections are usually needed for this procedure:
•
Computer
•
PoE switch or injector
•
CyberData device
4.1. In a test environment, use a computer that is connected to the same switch
as a single CyberData device. Note the subnet of the test computer.
4.2. Use the CyberData Discovery Utility program to locate the device on the
network. You can download the Discovery Utility program from the following
link:
https://www.cyberdata.net/pages/discovery
4.3. Wait for initialization to complete before using the Discovery Utility program
to scan for a device. The device will show the current IP address, MAC
address, and serial number.
4.4. Select the device.
4.5. Click Launch Browser. If the IP address is in a reachable subnet from the
computer that you are using to access the device, the Discovery Utility
program should be able to launch a browser window pointing to the device’s
IP address.
4.6. Log on to the web interface by using the default username (admin) and
password (admin) to configure the device.
4.7. Perform an audio test by pressing the Test Audio button that is located at
the bottom of the Device Configuration page. If the audio test message is
clearly audible, then your CyberData device is functioning properly.
4.8. The device is now ready to be set for your desired network configuration.
You may search the Compatible IP-PBX Servers index for available
sample VoIP phone system configurations and set up guides at the following
website address:
https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers
Quick Start Guide
931235A
5.0 Contacting CyberData VoIP Technical Support
You are welcome to call CyberData VoIP Technical Support at 831-373-2601
x333. Business hours are 7:00 AM - 5:00 PM Pacific Time, Monday through
Friday.
We encourage you to access our Technical Support help desk at the following
address:
http://support.cyberdata.net/
Note
You can also access the Technical Support help desk by going to
www.CyberData.net and clicking on the SUPPORT menu.
The Technical Support help desk provides the options of accessing
documentation for your CyberData product, browsing the knowledge base, and
submitting a troubleshooting ticket.
Please be advised requests for Returned Materials Authorization (RMA) numbers
require an active VoIP Technical Support ticket number. A product will not be
accepted for return without an approved RMA number.
Quick Start Guide
931235A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising