CyberData | 011461 | Owner Manual | Cyberdata 011461 SIP Vandal Resistant Keypad Phone Owner manual

Cyberdata 011461 SIP Vandal Resistant Keypad Phone Owner manual
Installation
Installation Quick Reference
Follow all appropriate electrical codes and use only approved electrical fittings for the installation.
The IP Endpoint Company
1. Determine if power to operate the device will be provided via the Ethernet or if external power will be required. If external power is
required, install an Auxiliary Power Supply or the equivalent. See the Terminal Block Connections section.
SIP Vandal Resistant Keypad Phone
SIP Compliant
011461
2. Choose a wall location that is free of obstructions and permits space for conduit runs. See the Dimensions section.
3. Ensure mounting can support 12 lbs. (5.5 kg) and any additional foreseeable load.
4. Ensure that none of the electrical connection circuits are live.
Parameter
Factory Default Setting
IP Addressing
DHCP
6. Disconnect the faceplate harness.
IP Addressa
10.10.10.10
7. Use the template provided or the enclosure itself to locate and drill holes for mounting screws.
Web Access Username
admin
8. Bring the Ethernet cable into the enclosure through the conduit entrance and connect to the RJ45 socket. If a conduit hub is used,
ensure that it is grounded to the ground stud. See the Wiring section of the Operations Guide.
Web Access Password
admin
9. Connect external power if provided. See the Terminal Block Connections section.
Default Gatewaya
5. Open the door, remove the screws on the faceplate and remove the faceplate.
Note Be careful when removing the faceplate. The circuit board is on the faceplate.
Subnet Mask
10. Connect the on-board relay if utilized. See the Operations Guide for details.
a
255.0.0.0
10.0.0.1
a. Default if there is not a DHCP server present.
11. Reconnect the faceplate harness.
Typical System Installation
12. Ensure all connections are secure.
13. Determine that the device is properly connected by pressing the RESET switch to announce the IP address (see the Reset Test
Function Management (RESET) Switch section). LEDs on the RJ45 connector indicate network connection and activity. See the
Operations Guide for LED details.
*More installation and mounting
options are available in the
Operations Guide.
Generic PoE Switch
14. Replace the faceplate.
15. Set up and configure if changes are required to the default settings.
16. Test the unit by calling to and from another device, preferably a VoIP device. See the Operations Guide for LED details.
SIP Weatherproof Keypad Phone
IP PBX Server
Getting Started
•
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011461/
•
Create a plan for the locations of your SIP Weatherproof Keypad Phones.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
Contacting CyberData
(1) SIP Vandal Resistant Keypad Phone
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931478C
Quick Reference
Quick Reference
931478C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Reset Test Function Management (RESET) Switch
Dimensions
4.0” [102 mm]
6.0” [153 mm]
7.9” [200 mm]
15.4” [391 mm]
0.35” [ 9 mm]
8.0” [202 mm]
9.3” [237 mm]
Terminal Block Connections
Alternate Power Input:
1 = Normally Open Common
2 = Normally Open Contact
1
2
Relay Contact:
(0.5 A at 30 VDC for continuous loads)
3 = +24 VDC @ 1000mA
4 = Power Ground
5 = Ringer +
6 = Ringer -
When the device is operational and linked to the network, use the Reset Test Function Management (RESET)
switch on the board (see picture) to announce the device’s IP address and test that the audio is working. During
the IP address announcement, you will hear the IP address of your device through the handset receiver.
To announce the device’s current IP address:
*Contacts 3 and 4 on the terminal block are only for
powering the device from a non-PoE +24 VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
1. Press and hold for two seconds.
WIRE IN
Can accept wire range from
16 AWG to 24 AWG
2. Release the RESET switch (see SW1 in the figure above).
Note The device will use DHCP to obtain the new IP address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
Note Pressing and holding the RESET switch for longer than five seconds will restore the device to the factory
default settings.
Operation
To restore the device to factory default settings:
•
The user will hear a dial tone when the handset is lifted.
•
Adjust the receiver volume with the switch in the handset.
When troubleshooting configuration problems, it is sometimes convenient to restore the device to a known state.
Note Each device is delivered with factory set default values.
Note The Operation details are explained in the Operations Guide.
To restore the factory default settings:
1. Press and hold the RESET switch (see SW1 in the figure above) until the device announces it is restoring to
factory defaults (approximately 5 seconds).
2. Release the RESET switch.
Note The device will use DHCP to obtain the new IP address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931478C
Quick Reference
Quick Reference
931478C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Conduit Access Hole
Ø0.98 [Ø25]
Printing Instruction:
1) Select Paper Size to: 11 [279] x 17 [432]
2) Orientation to: Portrait
3) Page Scaling to: NONE
Dimensions are in Inches [Millimeter]
Ø0.35 [Ø9]
(4 Places)
Fits 5/16” or 8mm
Diameter Screw or
Stud Anchors
4.03 [102.4]
6.8 [173]
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931478C
Quick Reference
Quick Reference
931478C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
7.9 [201]
12.4 [315]
13.9 [353]
2.9600 [75.2]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising