CyberData | 011311 | Quick Reference | Cyberdata 011311 InformaCast® Enabled Office Ringer Quick Reference

Cyberdata 011311  InformaCast® Enabled Office Ringer Quick Reference
Wall Mounting Options
Pre Drill Holes
(4 Places) on Wall
Installation Quick Reference
Backplate
Cable
Slots
Closed
The IP Endpoint Company
Pick One of Four Mounting Hole
for Ground Wire Connection
Wall
Cutout
Cable
Entry
Slot
Singlewire InformaCast Office Ringer
011311
Parameter
Network Cable &
Ground Wire
(Not Provided)
Factory Default Setting
IP Addressing
DHCP
a
121001A
Screw
Accessory Kit
IP Address
10.10.10.10
Web Access Username
admin
Web Access Password
admin
a
255.0.0.0
Subnet Mask
Mounting
Screw (3x)
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
Gang Box Mounting Options
Typical System Installation
*More installation and mounting
options are available in the
Operations Guide.
Cable
Slots
Closed
Backplate
Office Ringer
Backplate accept
Single Gang Box
or Two Gang Box
Cable
Entry
Slot
Office Ringer
IP Phone
InformaCast Server
Getting Started
Wall Cutout
•
Ground Wire
(Not Provided)
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011311/
Ground Wire Connect to
Any Available Mounting Hole
Mounting
Screw (3x)
121002B
Screw Accessory Kit
Single Gang Box use two
Two Gang Box use four
Contacting CyberData
•
Create a plan for the locations of your Office Ringers.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
Corporate Headquarters
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Office Ringer
Wall Cutout
Network Cable
(Not Provided)
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
802.3af Compliant Ethernet Switch
(1) Office Ringer Assembly
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
930917C
(1) Wall Mounting Kit
(1) Gang Box Mounting Kit
(4) #6 x 1.25-inch
Sheet Metal Screw
Quick Reference
Quick Reference
(4) Plastic ribbed anchor
930917C
(4) 6-32 x 0.5-inch flat
undercut Phillips machine
screw
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Dimensions
RTFM Button
RTFM button (SW1)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
•
Press and release the RTFM button within a five
second window.
Note
4.53 [115.0]
The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
•
Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
Recommended Wall Cutout Dimensions
0.38 [9.5]
2.14 [54.3]
ø0.19 [ø4.8]
(4 Places)
4.53 [115.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
2.39 [60.8]
3.40 [86.4]
0.50 [12.8]
Terminal Block Connections
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
3
4
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
Wire (IN)
1
8
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
0.25"
930917C
2.65 [67.3]
3.40 [86.4]
DIMENSIONS ARE IN INCHES [MILLIMETER]
Terminal Block
can accept 16 AWG wire
Quick Reference
Quick Reference
930917C
© 2017, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising