CyberData | 011406 | Operations Guide | Cyberdata 011406 InformaCast® Enabled Loudspeaker Amplifier (AC-Powered) Operations Guide

Cyberdata 011406  InformaCast® Enabled  Loudspeaker Amplifier (AC-Powered) Operations Guide
The IP Endpoint Company
Singlewire InformaCast
Loudspeaker Amplifier
(AC-Powered) 
Operations Guide
Part #011406
Document Part #931281G
for Firmware Version 11.6.4
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
Singlewire InformaCast Loudspeaker Amplifier Operations Guide 931281G
Part # 011406
COPYRIGHT NOTICE:
© 2018, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part
of this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by
third parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may
be the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
Operations Guide
931281G
CyberData Corporation
Revision Information
Revision 931281G, which corresponds to firmware version 11.6.4, was released on October 25,
2018 and has the following changes:
•
Adds the following feature to Section 1.3, "Product Features":
•
Supports Singlewire InformaCast High Quality Audio
Browsers Supported
The following browsers have been tested against firmware version 6.5.0:
Operations Guide
•
Internet Explorer (version: 10)
•
Firefox (also called Mozilla Firefox) (version: 23.0.1 and 25.0)
•
Chrome (version: 29.0.1547.66 m)
•
Safari (version: 5.1.7)
931281G
CyberData Corporation
Pictorial Alert Icons
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
GENERAL ALERT
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
•
Operations Guide
The safety guidelines for the equipment in this manual do not purport to address all the safety
issues of the equipment. It is the responsibility of the user to establish appropriate safety,
ergonomic, and health practices and determine the applicability of regulatory limitations prior to
use. Potential safety hazards are identified in this manual through the use of words Danger,
Warning, and Caution, the specific hazard type, and pictorial alert icons.
931281G
CyberData Corporation
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The Singlewire InformaCast Loudspeaker Amplifier enclosure is not rated for
any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
Operations Guide
931281G
CyberData Corporation
Abbreviations and Terms
Operations Guide
Abbreviation or Term
Definition
A-law
A standard companding algorithm, used in European digital
communications systems to optimize, i.e., modify, the dynamic range of an
analog signal for digitizing.
AVP
Audio Video Profile
Cat 5
TIA/EIA-568-B Category 5
DHCP
Dynamic Host Configuration Protocol
LAN
Local Area Network
LED
Light Emitting Diode
Mbps
Megabits per Second.
NTP
Network Time Protocol
PBX
Private Branch Exchange
PoE
Power over Ethernet (as per IEEE 802.3af standard)
RTFM
Reset Test Function Management
SIP
Session Initiated Protocol
u-law
A companding algorithm, primarily used in the digital telecommunication
UC
Unified Communications
VoIP
Voice over Internet Protocol
931281G
CyberData Corporation
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................3
1.4 Supported Protocols .................................................................................................................4
1.5 Supported SIP Servers .............................................................................................................4
1.6 Specifications ...........................................................................................................................5
1.7 Typical Coverage ......................................................................................................................6
1.7.1 Intelligibility Outdoor Field Test .......................................................................................6
1.7.2 Typical Warehouse Paging Setup ...................................................................................7
1.8 Compliance ..............................................................................................................................8
1.8.1 CE Testing ......................................................................................................................8
1.8.2 FCC Statement ..............................................................................................................8
Chapter 2 Installing the Singlewire InformaCast Loudspeaker Amplifier 9
2.1 Parts List ..................................................................................................................................9
2.2 Singlewire InformaCast Loudspeaker Amplifier Setup ...........................................................11
2.2.1 Singlewire InformaCast Loudspeaker Amplifier Components ......................................12
2.2.2 Loudspeaker Amplifier NEMA Box Components ..........................................................13
2.2.3 Assembling the Cable Gland ........................................................................................14
2.2.4 Installing the Singlewire InformaCast Loudspeaker Amplifier ......................................15
2.2.5 Installing the Universal Receptacle ..............................................................................16
2.2.6 Connecting the Power Cord and Ground Wires ...........................................................17
2.2.7 Connecting the Ground Wire ........................................................................................18
2.2.8 Connecting the Speaker Wires .....................................................................................19
2.2.9 Terminating the Network Cable Connector ...................................................................20
2.2.10 Connecting the Singlewire InformaCast Loudspeaker Amplifier to the Power Injector 21
2.2.11 Connecting the Singlewire InformaCast Loudspeaker Amplifier ...............................22
2.2.12 Singlewire InformaCast Loudspeaker Amplifier System Installation and Connection
Options ...........................................................................................................................24
2.2.13 Strobe Connections Behind the Port Cover ...............................................................26
2.2.14 Connecting the Optional 011288 Auxiliary RGB Strobe .............................................27
2.2.15 Singlewire InformaCast Loudspeaker Amplifier Jumpers ...........................................28
2.2.16 Ethernet Connection ..................................................................................................28
2.2.17 Loudspeaker Type ......................................................................................................29
2.2.18 Cabling/Wiring ............................................................................................................29
2.2.19 Confirm Operation ......................................................................................................30
2.2.20 Confirm the IP Address and Test the Audio ...............................................................31
2.2.21 Adjust the Volume ......................................................................................................32
2.3.1 Factory Default Settings ...............................................................................................35
2.3.2 Singlewire InformaCast Loudspeaker Amplifier Web Page Navigation ........................36
2.3.3 Using the Toggle Help Button .......................................................................................37
2.3.4 Log in to the Configuration Home Page .......................................................................39
2.3.5 Configure the Device ....................................................................................................43
2.3.6 Configure the Network Parameters .............................................................................51
2.3.7 Configure the SIP (Session Initiation Protocol) Parameters .........................................54
2.3.8 Configure the Multicast Parameters .............................................................................63
2.3.9 Configure the Sensor Page Parameters .......................................................................67
2.3.10 Configure the Audiofiles Page Parameters .................................................................71
2.3.11 Configure the Events Parameters ..............................................................................78
2.3.12 Configure the Autoprovisioning Parameters ...............................................................84
2.4.1 Downloading the Firmware ...........................................................................................96
2.4.2 Reboot the Device ........................................................................................................98
2.5.1 Command Interface Post Commands ..........................................................................99
Appendix A Mounting the Amplifier
104
A.1 Mount the Amplifier .............................................................................................................104
Appendix B Setting up a TFTP Server
Operations Guide
931281G
107
CyberData Corporation
ii
B.1 Set up a TFTP Server ..........................................................................................................107
B.1.1 In a LINUX Environment ............................................................................................107
B.1.2 In a Windows Environment .......................................................................................107
Appendix C Troubleshooting/Technical Support
108
C.1 Frequently Asked Questions (FAQ) ......................................................................................108
C.2 Documentation .....................................................................................................................108
C.3 Contact Information ..............................................................................................................109
C.4 Warranty and RMA Information ............................................................................................109
Index
Operations Guide
110
931281G
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the Singlewire InformaCast Loudspeaker Amplifier, look for a model number label similar
to the one shown in Figure 1-1. Confirm the following:
•
The model number on the label should be 011406.
Figure 1-1. Model Number Label1
www.cyberdata.net
Singlewire InformaCast Loudspeaker Amplifier (AC-Powered)
011406B / 021111H
406000001
CAN ICES-3 (A)/NMB-3(A)
00:20:F7:03:83:CA
V 11.6.4
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Model number
Serial number begins with 406
1. This figure is just an example. The revision and version information in this figure may be different than the label
on your product.
Operations Guide
931281G
CyberData Corporation
Product Overview 2
Typical System Installation
1.2 Typical System Installation
Figure 1-2 illustrates how the Singlewire InformaCast Loudspeaker Amplifier is normally installed as
part of a public address system.
Figure 1-2. Typical Installation
Compliant Non-PoE Ethernet Switch
Optional 011471
IP66 Analog Horn
(sold separately)
SIP Server
Singlewire InformaCast
Loudspeaker Amplifier
High Power PoE Injector in Box
Operations Guide
VoIP Phone
931281G
CyberData Corporation
Product Overview 3
Product Features
1.3 Product Features
•
Capable of receiving Singlewire InformaCast, SIP, and Multicast messages
•
Supports Singlewire InformaCast High Quality Audio
•
Plays audio from Multicast
•
SIP Enhanced interoperability for hosted environments
•
CyberData has maintained one of the most comprehensive list of IP PBX servers certified to
work with CyberData
•
Support for security code access for SIP paging
•
Autoprovisioning via HTTPS
•
HTTPS web based configuration
•
Support for G.711 a-law, G.711u-law, G.722, and G.729 codecs
•
802.11q VLAN tagging
•
Configurable sense input for use with fault detection
•
Configurable event generation for device health and status monitoring
•
Optional direct connect RGB strobe kit connection
•
9 user-uploadable page messages
•
Receives pages directly from Polycom phones
•
Packaged in a UL 94-HB flame resistant, IK 08 Impact-rated, IP66 enclosure
•
Dual-speed ethernet 10/100 Mbps
•
PoE 802.3at-enabled
•
Line-in for background music
•
Line-out connector
•
DTMF controlled relay
•
Direct 8 Ohm speaker drive
•
User-uploadable tones and messages
•
Digital and manual volume control
•
Second SIP endpoint "Night Ringer"
•
Auto-call voice message from input port sense
•
Can support one or two analog horns (#011471 IP66 Analog Horn sold separately)
•
HTTP Command Interface
•
10 channel prioritized Multicast ports
•
Built-in diagnostics
•
Delayed page support
•
Cisco SRST
Singlewire InformaCast Features
Operations Guide
•
Dual registration for Singlewire and SIP
•
Singlewire Informacast compatibility available. Includes support for Informacast resiliency
•
Support both SIP and Singlewire InformaCast
931281G
CyberData Corporation
Product Overview 4
Supported Protocols
•
InformaCast compliant
1.4 Supported Protocols
The Singlewire InformaCast Loudspeaker Amplifier supports:
•
SIP
•
InformaCast Version 4.0 and greater
•
Multicast
•
HTTP and HTTPS web-based configuration
Provides an intuitive user interface for easy system configuration and verification of Singlewire
InformaCast Loudspeaker Amplifier operations.
•
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
•
TFTP Client
Facilitates hosting for the configuration file for Autoprovisioning.
•
RTP
•
RTP/AVP - Audio Video Profile
•
SPEEX
•
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
G.722
G.729
Packet Time 20 ms
1.5 Supported SIP Servers
The following link contains information on how to configure the Singlewire InformaCast Loudspeaker
Amplifier for the supported SIP servers:
https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers
Operations Guide
931281G
CyberData Corporation
Product Overview 5
Specifications
1.6 Specifications
Table 1-1. Specifications
Specifications
Ethernet I/F
10/100 Mbps
Protocol
InformaCast and/or SIP (RFC 3261)
Power Input
PoE 802.3at
Audio Output
802.3at: 117.9 (+/- 0.2) dBC @1M and 1kHza
Line In:
Input Signal Amplitudes
2.0 VPP maximum
Input Impedance
10k Ohm
Line Out:
Output Signal Amplitudes
2.0 VPP maximum
Output Level
+2dBm nominal
Total Harmonic Distortion
0.5% maximum
Output Impedance
10k Ohm
Operating Range
Temperature: -40o C to 55o C (-40o F to 131o F)
Humidity: 5-95%, non-condensing
Enclosure
UL 94-HB flame resistant, IK 08 Impact-rated, IP66 enclosure
Storage Temperature
-40o C to 70o C (-40o F to 158o F)
Storage Altitude
Up to 15,000 ft. (4573 m)
Payload Types
G.711 a-law, G.711u-law, G.722, and G.729 codecs
Dimensionsb
10 in. [254 mm] Length
4 in. [101.6 mm] Width
14 in. [355.6 mm] Height
Weight
3.6 lbs. [1.63 kg]
Compliance
CE; EMC Directive – Class A EN 55032 & EN 55024, LV Safety Directive –
EN 60950-1, RoHS Compliant, FCC; Part 15 Class A, Industry Canada;
ICES-3 Class A, IEEE 802.3 Compliant
Part Number
011406
Horn Part Number
011471
a.When used with the optional 011471 IP66 Analog Horn (sold separately).
b. Dimensions are measured from the perspective of the product being upright with the front of the product facing you.
Operations Guide
931281G
CyberData Corporation
Product Overview 6
Typical Coverage
1.7 Typical Coverage
With one horn attached to Paging Amplifier under standard 802.3af PoE power, coverage is up to
5,000 square feet. With two horns attached to the Paging Amplifier under 802.3at PoE (high power),
coverage is up to 10,000 square feet depending on ambient background noise levels.
1.7.1 Intelligibility Outdoor Field Test
The figure below shows the intelligibility outdoor field test of the device when it is used with the
011471 IP66 Outdoor Analog Horn.
Figure 1-3. Intelligibility Outdoor Field Test
Speaker Placement
15 Ō high
Football
Field
0, 0
344Ō
295Ō
344Ō
295Ō
377Ō
377Ō
459Ō
459Ō
443Ō
BOOST 1
intelligibility
limit
443Ō
591Ō
591
59
9 1Ō
623Ō
6
23Ō
Ō
623Ō
Ambient Noise:
~70dBC
Operations Guide
BOOST3
intelligibility
limit
Note: Boost 3 can be slightly distorted on the high
end of the audio waveform, but this boost will
output a higher dB level and is sƟll intelligible in
our tesƟng.
722Ō
931281G
CyberData Corporation
Product Overview 7
Typical Coverage
1.7.2 Typical Warehouse Paging Setup
Figure 1-4. Typical Warehouse Paging Setup
Loud Speaker Amplifier
Part Numbers: 011404 and 011405
"High Power Mode" with
Two (2) Horn Speakers Attached
Horn Speaker
Horn Speaker
Horn Speaker
Horn to Loud Speaker Amplifier
25'
25'
Horn Speaker
Loud Speaker Amplifier
Horn Speaker
Horn Speaker to Horn Speaker
50'
Horn Speaker
Office
Bathroom
Typical Example of a 70,000 Square Feet Warehouse Paging Set up
Operations Guide
931281G
CyberData Corporation
Product Overview 8
Compliance
1.8 Compliance
1.8.1 CE Testing
CE testing has been performed according to EN ISO/IEC 17050 for Emissions, Immunity, and Safety.
Note
You can download the Declaration of Conformity document from the Downloads tab of the
product’s webpage.
1.8.2 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Operations Guide
931281G
CyberData Corporation
9
2 Installing the Singlewire InformaCast
Loudspeaker Amplifier
2.1 Parts List
Table 2-2 illustrates the parts for each Singlewire InformaCast Loudspeaker Amplifier.
Table 2-2. Parts List
Operations Guide
Quantity
Part Name
1
Singlewire InformaCast Paging Amplifier Assembly
1
Enclosure
1
Installation Quick Reference Guide
1
PoE Power Injector
1
CAT 5e/CAT6 cable
1
Ground Wire
931281G
Illustration
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 10
Parts List
Table 2-2. Parts List (continued)
Quantity
Part Name
1
Mounting Accessory Kit which includes:
Illustration
(4) #8 Plastic Anchors
(4) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
#8 x 1.25" Pan Head
Phillip Drive
Self-Tapping Screw (4x)
#8 Plastic Tri-Lobe
Light Duty Anchor (4x)
Operations Guide
1
IEC Power Cord
1
Universal Receptacle
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 11
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2 Singlewire InformaCast Loudspeaker Amplifier Setup
Set up and configure each Singlewire InformaCast Loudspeaker Amplifier before you mount it.
CyberData delivers each Singlewire InformaCast Loudspeaker Amplifier with the factory default
values indicated in
Table 2-3:
Table 2-3. Factory Default Settings—Default of Network
Parameter
Factory Default Setting
IP Addressing
IP
DHCP
Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
a
10.0.0.1
Default Gateway
a.Default if there is not a DHCP server present.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 12
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.1 Singlewire InformaCast Loudspeaker Amplifier Components
Figure 2-5 shows the components of the Singlewire InformaCast Loudspeaker Amplifier.
Figure 2-5. Singlewire InformaCast Loudspeaker Amplifier Components
RTFM Switch
VoIP
Loudspeaker
RTFM
To broadcast the device’s current IP address, use a bent
paperclip or a similar object to press and hold the RTFM switch
(located behind the hole) for a couple of seconds and then
release it.
To restore the factory defaults, complete the following steps:
1. Use a bent paperclip or a similar object to press and hold the
RTFM switch until you hear the device announce the words,
“restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the
factory default settings.
Speaker Volume
Volume
SPD Link/Act.
Speed (SPD) LED (AMBER)
The Speed (SPD) LED illuminates AMBER for a 100Mb link 
or is off for 10MB when the network link to the device is 
established.
Link/Activity (Link/Act.) LED (GREEN) 
The GREEN Link/Activity (Link/Act.) LED blinks to indicate
network traffic.
PWR Status
Status LED (GREEN)
After supplying power to the device, a steady GREEN Status LED
illuminates. After about 20 seconds, the GREEN Status LED will
blink fast to indicate that the device is acquiring an IP address and
attempting to autoprovision. The GREEN Status LED will turn off
thereafter until the device has finished booting. When the device
has fully booted, the GREEN Status LED will turn on solid to
confirm the device is operational.
The GREEN Status LED will blink during a page when it is online.
Power (PWR) LED (GREEN/BLUE)
The Power (PWR) LED is GREEN in low power mode (802.3af)
and BLUE during high power mode (802.3at).
The IP Endpoint Company
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 13
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.2 Loudspeaker Amplifier NEMA Box Components
Figure 2-6 shows all of the NEMA box components of the loudspeaker amplifier.
Figure 2-6. Loudspeaker Amplifier Components—AC powered
PoE Injector
RTFM Switch
MIC Input
Auxiliary Strobe Input
Volume
LEDs
Speaker Connection
Ethernet Connection
AC power
See Section 2.2.5,
"Installing the Universal Receptacle"
Data In
Data and Power Out
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 14
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.3 Assembling the Cable Gland
Assemble the cable gland as shown in Figure 2-7.
Figure 2-7. Assembling the Cable Gland
Washer
Nut
Coupling
Bushing
End Cap
Hole Plug
Operations Guide
931281G
NEMA
Enclosure
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 15
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.4 Installing the Singlewire InformaCast Loudspeaker Amplifier
Install the Singlewire InformaCast Loudspeaker Amplifier as shown in Figure 2-8.
Figure 2-8. Installing the Singlewire InformaCast Loudspeaker Amplifier
Paging Amplifier
Mounting Screw
Paging Amplifier
Network Cable
to Network Port
Network Cable
through Cable Gland
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 16
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.5 Installing the Universal Receptacle
Install the universal receptacle as shown in Figure 2-9.
Figure 2-9. Installing the Universal Receptacle
Stripe Wires to
3/8" / 0.328" [8mm]
Tin Bare Wires for
Easy Insert
L = LIVE
Button
Hold Down to Insert Wire
Release to Engage
Break K.O.
for Cable Exit
N = Neutral
Knock Out
(K.O.)
Mounting
Screw
Universal
Receptacle
Universal
Receptacle
E = EARTH
GROUND
Nut
Washer
Power Cord
Coupling
Bushing
End Cap
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 17
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.6 Connecting the Power Cord and Ground Wires
Connect the power cord and ground wires to the universal receptacle. See Figure 2-10 and Figure 211.
Figure 2-10. Wiring the Universal Receptacle
LIVE
SIDE PANEL
KNOCK OUT
NEUTRAL
L
SIDE PANEL
KNOCK OUT
E
N
EARTH
GROUND
Operations Guide
EARTH
GROUND
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 18
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.7 Connecting the Ground Wire
Connect the ground wire from the universal receptacle to the device as shown in Figure 2-11.
Figure 2-11. Ground Wire Connection
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 19
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.8 Connecting the Speaker Wires
Connect the speaker wires to the terminal block as shown in Figure 2-12.
Figure 2-12. Connecting the Speaker Wires
Tool Required for
Speaker Wires Installation:
1) A Slotted 3/32" Width or
0.4 x 2.5mm Screwdriver
12 (+)
9 ( --)
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 20
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.9 Terminating the Network Cable Connector
Terminate the network cable connector as shown in Figure 2-14.
Figure 2-13. Terminating the Network Cable Connector
Cable Gland
Assembly
Power Injector
Cable Gland
Assembly
Operations Guide
Paging Amplifier Assembly
Network Cable
to Power Injector (IN)
Terminate Connector After
Cable Passed Enclosure
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 21
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.10 Connecting the Singlewire InformaCast Loudspeaker Amplifier to
the Power Injector
Connect the Singlewire InformaCast Loudspeaker Amplifier to the power injector as shown in Figure
2-14.
Figure 2-14. Connecting the Singlewire InformaCast Loudspeaker Amplifier to the Power Injector
OUT
IN
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 22
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.11 Connecting the Singlewire InformaCast Loudspeaker Amplifier
2.2.11.1 Using the Amplified Outputs
High Power Mode The following figure illustrate how to connect the Singlewire InformaCast Loudspeaker Amplifier and
(One Speaker)
use the amplified outputs in high power mode to one speaker or horn.
Figure 2-15. Using the Amplified Outputs—High Power Mode with One Speaker
CLASS II WIRING
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
Note: You can use an
802.3at compliance
switch instead of an
802.3at power injector
and hub.
Non-PoE Ethernet Switch
(sold separately)
+
*Note: The drawing below is turned
around from the actual position of the
terminal block in the picture.
*Note: Horn is connected to terminal
block pins 9 (-) and 12 (+) of the
paging amplifier for mono mode.
Cat 5 Ethernet Cable
*Note: This AC connection needs to
be installed by a certified electrician.
~
*+
AC Input*
*Note: The positive (+) wire coming from the speaker
may be red or white. The negative (-) wire is black.
*Note: If you are using 16 gauge (AWG)
wiring, the maximum recommended
length of the wiring to the horn should be
50 feet or less from the amplifier.
*Note: 16 gauge (AWG) wiring is recommended. 
If the speaker will be routed outside, then CyberData
suggests using CL2 or CL3 certified wiring.
Standard 1 Speaker Configuration
(802.3at mode)
8 Ohms
Note: The IP66 Analog Horn (011471) comes with a
3.28 foot cable, which can be connected directly to the
amplifier. If the wiring is greater than 3.28 feet, then it
is suggested to use solder and heat shrink tubing to
fasten the additional wires. Twist wire nuts can be
used as an alternative if it is protected sufficiently.
+
Twist wire nuts
Operations Guide
931281G
011471 IP66 Analog Horn
(sold separately)
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 23
Singlewire InformaCast Loudspeaker Amplifier Setup
High Power Mode The following figure illustrate how to connect the Singlewire InformaCast Loudspeaker Amplifier and
(Two Speakers)
use the amplified outputs in high power mode to two speakers or horns.
Figure 2-16. Using the Amplified Outputs—High Power Mode with Two Speakers
CLASS II WIRING
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
Note: You can use an
802.3at compliance
switch instead of an
802.3at power injector
and hub.
Non-PoE Ethernet Switch
(sold separately)
+
*Note: The drawing below is turned
around from the actual position of the
terminal block in the picture.
*Note: Horn is connected to terminal
block pins 9 (-) and 12 (+) of the
paging amplifier for mono mode.
Cat 5 Ethernet Cable
*Note: This AC connection needs to
be installed by a certified electrician.
~
*+
AC Input*
*Note: 16 gauge (AWG) wiring is recommended. 
If the speaker will be routed outside, then CyberData
suggests using CL2 or CL3 certified wiring.
*Note: If you are using 16 gauge (AWG)
wiring, the maximum recommended
length of the wiring to each horn should
be 25 feet or less from the amplifier.
Optional 2 Speaker Configuration
(802.3at mode)
8 Ohms
Standard 1 Speaker Configuration
(802.3at mode)
8 Ohms
+
2 speakers in parallel (4 Ohm total)
011471 IP66 Analog Horn
(sold separately)
Operations Guide
*Note: The positive (+) wire coming from the speaker
may be red or white. The negative (-) wire is black.
+
Twist wire nuts
011471 IP66 Analog Horn
(sold separately)
Note: The IP66 Analog Horn (011471) comes with a 3.28 foot cable,
which can be connected directly to the amplifier. If the wiring is
greater than 3.28 feet, then it is suggested to use solder and heat
shrink tubing to fasten the additional wires. Twist wire nuts can be
used as an alternative if it is protected sufficiently.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 24
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.12 Singlewire InformaCast Loudspeaker Amplifier System Installation
and Connection Options
The following figures show the connection options for the Singlewire InformaCast Loudspeaker
Amplifier.
Figure 2-17. Singlewire InformaCast Loudspeaker Amplifier Connections
CLASS II WIRING
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
Speaker Connections
(Figure 2-15)(Figure 2-16)
Line-Out Connection (10K Ohm)
Line-In Connection (Figure 2-18)
Relay Connection (Figure 2-19)
Sensor Connection (Figure 2-20)
Figure 2-18. Line-In Connection
When line-in is enabled on
the device, the audio
received from the line-in
connection will be played
to the speaker(s) and lineout connection as the lowest priority audio.
Loudspeaker Amplifier
Music Source
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 25
Singlewire InformaCast Loudspeaker Amplifier Setup
Figure 2-19. Relay or LED Strobe Connection
When the device is called from a
remote phone, the relay on the
device can be programmed to blink
and drive an LED Strobe Light.
External device
such as an
electric door strike
or an LED Strobe
Light
AC or DC
Power
Source
High PIV Ultrafast
Switching Diode
Solid State or 
Mechanical Relay
OUT
IN
Output Contacts
AC or DC-rated
depending upon
controlled device
requirements
DC Power Supply
(Max. 30 VDC @ 1A)
Figure 2-20. Sensor Connection
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 26
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.13 Strobe Connections Behind the Port Cover
See Figure 2-21 for the additional connection options for the Singlewire InformaCast Loudspeaker
Amplifier.
Figure 2-21. Connections Behind the Port Cover
CLASS II WIRING
MIC IN
3
2
1
STROBE
5
4
3
2
1
See Table 2-4 for the descriptions of the connections behind the port cover.
Table 2-4. Connections Behind the Port Cover
Microphone Connections
Name
MIC IN
Connection
Description
J6-1
Microphone chassis ground connections
J6-2
Microphone signal input
J6-3
Microphone common input
Connection
Description
J9-1
Ground
J9-2
Strobe positive power (+24V)
J9-3
Ground
J9-4
I2C data
J9-5
I2C clock
Strobe Connections
Name
STROBE
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 27
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.14 Connecting the Optional 011288 Auxiliary RGB Strobe
1. Remove the mounting screw to remove the cover plate. See Figure 2-22.
2. Remove the hole plug and grommet. See Figure 2-22.
3. Slide the cover plate through the slot on the cable grommet. See Figure 2-22.
4. Feed the strobe cable through an available gland near the bottom of the enclosure.
5. Connect the strobe cable to the STROBE connection of the device at J9 (see Figure 2-22) and
to J1 of the board of the optional 011288 Auxiliary RGB Strobe (sold separately).
6. Install the mounting screw to secure the cover plate. See Figure 2-22.
Figure 2-22. Connecting the Optional 011288 Auxiliary RGB Strobe
Remove Hole Plug
and Grommet
Slide Cable Grommet
into Cover Plate Slot
Cover
Screw
Backplate
Cover
Plate
Cable Gland
Assembly
to
STROBE
(J9)
Slot
to
J1
J1
Network Patch Cable to
Power Injector (OUT)
Power Injector
Cable
Exit
RGB
Strobe
Assembly
Optional
011288
Auxiliary RGB Strobe
(sold separately)
Paging Amplifier Assembly
Cable Gland
Assembly
Network Cable
to Power Injector (IN)
Network Patch Cable to
Network Port on Paging Amplifier
Cable Gland Plug
Shield Unused Gland
from Element
The cable gland plug shields
the unused gland
from dust and other external elements
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 28
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.15 Singlewire InformaCast Loudspeaker Amplifier Jumpers
See Figure 2-23 for the jumper locations.
Figure 2-23. Jumper Locations
JP4
JP2
JP3
JP5
JP1
See Table 2-5 for the jumper descriptions.
Table 2-5. Jumper Descriptions
Jumper
Description
JP1
Reset—Factory Only
JP2
RTFM (not installed)
JP3
Audio Enable Jumper—Factory Only
JP4
Relay NO/NC (default to NO)—Factory Only
JP5
PoE IEEE 802.3at—Factory Only
2.2.16 Ethernet Connection
See Table 2-6 for details about the Singlewire InformaCast Loudspeaker Amplifier connection.
Table 2-6. Singlewire InformaCast Loudspeaker Amplifier Connection
Operations Guide
Connection
Connection Details
Location
Ethernet
Use a RJ 45 cable.
Singlewire InformaCast
Loudspeaker Amplifier (ACPowered)
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 29
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.17 Loudspeaker Type
Using the amplified output, the CyberData Singlewire InformaCast Loudspeaker Amplifier supports
the 011471 Horn or equivalent unamplified loudspeaker.
Figure 2-24. 011471 Horn
2.2.18 Cabling/Wiring
Using the amplified output, you may connect a 011471 loudspeaker or equivalent unamplified
speaker to a Singlewire InformaCast Loudspeaker Amplifier with good quality speaker wire that is 16
gauge and limited to 25 feet in length with two loudspeakers or 50 feet in length with one
loudspeaker.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 30
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.19 Confirm Operation
After connecting the device to the 802.3af compliant ethernet hub, use the LEDs on the device to
confirm that the device is operational and linked to the network.
Table 2-7. Singlewire InformaCast Loudspeaker Amplifier LEDs
LED
Color
Function
Power (PWR)
BLUE/GREEN
The 802.3at power injector that is provided with the device should
cause the Power (PWR) LED to illuminate BLUE to indicate that high
power is available.
The Power (PWR) LED may illuminate GREEN if a low power mode
(802.3af) power source is used (not included and sold separately).
GREEN
Status
After supplying power to the device, a steady GREEN Status LED
illuminates.
After about 20 seconds, the GREEN Status LED will blink fast to
indicate that the device is acquiring an IP address and attempting to
autoprovision. The GREEN Status LED will turn off thereafter until
the device has finished booting. When the device has fully booted,
the GREEN Status LED will turn on solid to confirm the device is
operational.
The GREEN Status LED will blink during a page when it is online.
Speed (SPD)
AMBER
The Speed (SPD) LED illuminates AMBER for a 100Mb link or is off
for 10MB when the network link to the device is established.
Link/Activity (Link/Act.)
GREEN
The Link/Activity (Link/Act.) GREEN LED blinks to indicate
network traffic.
Figure 2-25. Singlewire InformaCast Loudspeaker Amplifier LEDs
Volume
Speed (SPD) LED
(AMBER)
Power (PWR) LED
(BLUE/GREEN)
Operations Guide
SPD Link/Act
PWR
931281G
Status
Link/Activity (Link/Act.) LED
(GREEN)
Status LED
(GREEN)
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 31
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.20 Confirm the IP Address and Test the Audio
2.2.20.1 RTFM Switch
When the Singlewire InformaCast Loudspeaker Amplifier is operational and linked to the network,
use the Reset Test Function Management (RTFM) switch (Figure 2-26) (located behind the hole on
the device) to announce and confirm the device’s IP Address and test the audio to verify that it is
working.
Figure 2-26. RTFM Switch
RTFM switch 
(located behind the hole 
on the device)
Announcing the IP To announce a device’s current IP address:
Address
•
Use a bent paperclip or a similar object to press and hold the RTFM switch for a couple of
seconds and then release it.
Caution
GENERAL ALERT
Restoring the
Factory Default
Settings
Equipment Caution: Pressing and holding the RTFM switch for more than five
seconds will restore the device to the factory default settings. See the “Restoring
the Factory Default Settings” section.
To restore the factory default settings, complete the following steps:
1. Use a bent paperclip or a similar object to press and hold the RTFM switch until you hear the
device announce the words, “restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the factory default settings.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 32
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.21 Adjust the Volume
There are two ways to adjust the volume for the Singlewire InformaCast Loudspeaker Amplifier:
•
The SIP Volume setting on the Device Configuration Page
•
The external Volume dial (Figure 2-28) on the Singlewire InformaCast Loudspeaker
Amplifier face
Figure 2-27. External Volume Dial
Volume
SPD Link/Act
External volume dial
PWR
Status
2.2.21.1 The SIP Volume Setting
To adjust the volume of the device with the SIP Volume setting on the Device Configuration Page,
complete the following steps:
1. Go to the Home Page.
2. Select the Device Configuration Page page.
3. In the SIP Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.21.2 The Multicast Volume Setting
To adjust the Multicast Volume volume with the Multicast Volume setting on the Device
Configuration Page, complete the following steps:
1. Go to the Home Page.
2. Select the Device Configuration Page.
3. In the Multicast Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 33
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.21.3 The Ring Volume Setting
To adjust the Ring Volume volume with the Ring Volume setting on the Device Configuration
Page, complete the following steps:
1. Go to the Home Page.
2. Select the Device Configuration Page.
3. In the Multicast Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.21.4 The Sensor Volume Setting
To adjust the Sensor Volume volume with the Sensor Volume setting on the Device Configuration
Page, complete the following steps:
1. Go to the Home Page.
2. Select the Device Configuration Page.
3. In the Sensor Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.21.5 The Loopback Volume Setting
To adjust the Loopback Volume volume with the Loopback Volume setting on the Device
Configuration Page, complete the following steps:
1. Go to the Home Page.
2. Select the Device Configuration Page.
3. In the Loopback Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 34
Singlewire InformaCast Loudspeaker Amplifier Setup
2.2.21.6 External Volume Dial
To adjust the Singlewire InformaCast Loudspeaker Amplifier volume with the external volume dial,
complete the following steps:
1. Turn the external Volume dial (Figure 2-27) on the Singlewire InformaCast Loudspeaker
Amplifier face.
Note
For the lineout volume, the volume is fixed and the volume control is adjusted through an
external amplifier.
Figure 2-28. External Volume Dial
Volume
SPD Link/Act
External volume dial
PWR
Operations Guide
931281G
Status
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 35
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3 Configure the Singlewire InformaCast Loudspeaker
Amplifier Parameters
To configure the Singlewire InformaCast Loudspeaker Amplifier online, use a standard web browser.
Configure each Singlewire InformaCast Loudspeaker Amplifier and verify its operation before you
mount it. When you are ready to mount an Singlewire InformaCast Loudspeaker Amplifier, refer to
Appendix A, "Mounting the Amplifier" for instructions.
2.3.1 Factory Default Settings
All Singlewire InformaCast Loudspeaker Amplifiers are initially configured with the following default
IP settings:
When configuring more than one Singlewire InformaCast Loudspeaker Amplifier, attach the
Singlewire InformaCast Loudspeaker Amplifiers to the network and configure one at a time to avoid
IP address conflicts.
Table 2-8. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
Default Gatewaya
255.0.0.0
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 36
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.2 Singlewire InformaCast Loudspeaker Amplifier Web Page Navigation
Table 2-9 shows the navigation buttons that you will see on every Singlewire InformaCast
Loudspeaker Amplifier web page.
Table 2-9. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Network page.
Link to go to the SIP page.
Link to the Multicast page.
Link to the Sensor page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Autoprovisioning page.
Link to the Firmware page.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 37
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-29 and Figure 2-30.
Figure 2-29. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-30.
Figure 2-30. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 38
Singlewire InformaCast Loudspeaker Amplifier Setup
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-31.
), and a short description of the web
Figure 2-31. Short Description Provided by the Help Feature
Question mark
Operations Guide
931281G
A short description of the 
web page item will appear
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 39
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.4 Log in to the Configuration Home Page
1. Open your browser to the Singlewire InformaCast Loudspeaker Amplifier IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Singlewire InformaCast
Loudspeaker Amplifier.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
https://www.cyberdata.net/pages/discovery
Note
The device ships in DHCP mode. To get to the Home page, use the discovery utility to scan
for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-32):
Web Access Username: admin
Web Access Password: admin
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 40
Singlewire InformaCast Loudspeaker Amplifier Setup
Figure 2-32. Home Page
406100001
v11.6.4
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 41
Singlewire InformaCast Loudspeaker Amplifier Setup
3. On the Home page, review the setup details and navigation buttons described in Table 2-10.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-10. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
SIP Mode
Shows the current status of the SIP mode.
Multicast Mode
Shows the current status of the Multicast mode.
Event Reporting
Shows the current status of the Event Reporting mode.
Nightringer
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Nightringer Server
Shows the current status of Nightringer Server.
Singlewire Settings
Boot Time
Shows the boot time.
Current Time
Shows the current time.
IC Servers
Shows the InformaCast server IP addresses.
Configuration File
Shows the configuration file.
B’casts Accepted
Shows the number of B’casts accepted.
B’casts Rejected
Shows the number of B’casts rejected.
B’casts Active
Shows the number of active B’casts.
Import Settings
Use this button to select a configuration file to import.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 42
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-10. Home Page Overview (continued)
Web Page Item
Description
After selecting a configuration file, click Import to import the
configuration from the selected file. Then, click Save and Reboot to
store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you will
see a question mark ( ) appear next to some of the web page items.
Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 43
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.5 Configure the Device
1. Click the Device menu button to open the Device page. See Figure 2-33.
Figure 2-33. Device Configuration Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 44
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Device page, you may enter values for the parameters indicated in Table 2-11.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-11. Device Configuration Parameters
Web Page Item
Description
Volume Settings (0-9)
Disable Volume Control Dial
Select this option to disable the volume control dial and enable digital
volume control settings.
SIP Volume
Set the speaker volume for a SIP call. A value of 0 will mute the speaker
during SIP calls.
Multicast Volume
Set the speaker volume for multicast audio streams. A value of 0 will mute
the speaker during multicasts.
Ring Volume
Set the ring volume for incoming calls. A value of 0 will mute the speaker
instead of playing the ring tone when Auto-Answer Incoming Calls is
disabled.
Sensor Volume
Set the speaker volume for playing sensor activated audio. A value of 0
will mute the speaker during sensor activated audio.
Loopback Volume
Speaker volume for Line-in Loopback. This value only affects the volume
of the speaker(s). Line-out volume must be controlled by the amplifier
connected to the line-out port.
Volume Boost:
Set the Boost level to increase the volume output of the speaker. Using
Volume Boost may introduce audio clipping and/or distortion. Boost is
only recommended for use with volumes set to level 9.
No Volume Boost
+4dB
Clock Settings
Set Time with NTP Server on boot
When selected, the time is set with an external NTP server when the
device restarts.
NTP Server
Use this field to set the address (in IPv4 dotted decimal notation or as a
canonical name) for the NTP Server. This field can accept canonical
names of up to 64 characters in length.
Posix Timezone String
See Section 2.3.5.1, "Time Zone Strings" for information about how to
use the Posix Timezone String to specify time zone and daylight savings
time where applicable. Enter up to 63 characters.
Periodically sync time with server
When selected, the time is periodically updated with the NTP server at
the configured interval below.
Time update period (in hours)
The time interval after which the device will contact the NTP server to
update the time. Enter up to 4 digits.
Current Time
Allows you to input the current time. (6 character limit)
Power Settings
802.3AT Mode
Operations Guide
This device automatically detects if it is plugged into an 802.3AT (also
known as PoE Plus) power source. 802.3AT provides more power than
older 802.3AT power sources and allows this speaker to play audio at
higher volumes. If you are sure this speaker is connected to an 802.3AT
power source, but it is not being detected correctly, you can override the
automatic settings below.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 45
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-11. Device Configuration Parameters (continued)
Web Page Item
Description
Force 802.3AT Mode (NOT recommended)
Enable this option if you are sure this speaker is connected to an 802.3AT
power source, but it is not being detected correctly (not recommended).
Auxiliary Power Supply
This device can be connected to a +24VDC auxiliary power supply.
Check this box if this is how this speaker is being powered.
Singlewire Broadcast Strobe Settings
For up to 10 Singlewire pages, when a priority is specified for the page, a
corresponding strobe scene will be activated. The color may be selected
from the drop down menu, or customized by the user with the 0-255
scale. Brightness is specified with a value between 0 and 100.
Priority
Indicates the priority of the Singlewire broadcast, with 1 the highest
priority and 10 the lowest.
Scene
Use this section to select the strobe flashing behavior for the Singlewire
Broadcast.
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
Color
Select the desired color (only one may be chosen).
Brightness
How bright the strobe will blink when there is a Singlewire Broadcast.
This is the maximum brightness for “fade” type scenes.
Red
The red LED value for the Singlewire Broadcast.
Green
The green LED value for the Singlewire Broadcast.
Blue
The blue LED value for the Singlewire Broadcast.
Use this button to preview the strobe flashing behavior for the Singlewire
Broadcast Strobe Settings.
Line-In Settings
Enable Line-in to Line-out Loopback
Operations Guide
Line-in audio will play back out the device's audio output ports. This is the
lowest priority audio and will be preempted by any other audio stream.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 46
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-11. Device Configuration Parameters (continued)
Web Page Item
Description
DTMF Settings
Require Security Code
When selected, the user will be prompted to enter a Security Code
(entered on this page) before being able to execute a page when calling
the device.
Security Code
Type the Security Code in this field. The Security Code must only use
characters '0-9', '*' and '#'. Enter up to 25 characters.
Enable Stored Message Playback
When selected, the caller will be prompted to select one of nine stored
messages to play through the speaker. Stored messages may be
customized on the Audiofiles page.
Relay Settings
Activate Relay with DTMF Code
Activates the relay when the DTMF Activation Code is entered on the
phone during a SIP call with the device. RFC2833 DTMF payload types
are supported.
Relay Pulse Code
DTMF code used to pulse the relay when entered on a phone during a
SIP call with the device. Relay will activate for Relay Pulse Duration
seconds then deactivate. Activate Relay with DTMF Code must be
enabled. Enter up to 25 digits (* and # are supported).
Relay Pulse Duration (in seconds)
The length of time (in seconds) during which the relay will be activated
when the DTMF Relay Activation Code is detected. Enter up to 5 digits.
Relay Activation Code
Activation code used to activate the relay when entered on a phone
during a SIP call with the device. Relay will be active indefinitely, or until
the DTMF Relay Deactivation code is entered. Activate Relay with DTMF
Code must be enabled. Enter up to 25 digits (* and # are supported).
Relay Deactivation Code
Code used to deactivate the relay when entered on a phone during a SIP
call with the device. Activate Relay with DTMF Code must be enabled.
Enter up to 25 digits (* and # are supported).
Activate Relay During Ring
When selected, the relay will be activated for as long as the device is
ringing. When Auto-Answer Incoming Calls is enabled, the device will not
ring and this option does nothing.
Activate Relay During Night Ring
When selected, the relay will be activated as long as the Nightringer
extension is ringing.
Activate Relay While Call Active
When selected, the relay will be activated as long as the SIP call is active.
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Auto-Answer Incoming Calls
When selected, the device will automatically answer incoming calls.
When Auto-Answer Incoming Calls is disabled, the device will play a
ring tone (corresponds to Ring Tone on the Audiofiles page) out of the
speaker.
Beep on Init
Device will play the user-defined “pagetone” audio file when it boots.
Beep on Page
Device will play the user defined “pagetone” audio file before playing a
SIP page.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do not
recommend disabling HTTPS for security reasons.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 47
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-11. Device Configuration Parameters (continued)
Web Page Item
Description
Two Speakers Connected
Specify if one or two speakers are connected to the paging amplifier. If
only one is connected, ensure that it is wired to the first set of terminal
blocks.
RGB Strobe
Status of optional RGB Strobe.
Click on the Test Audio button to do an audio test. When the Test Audio
button is pressed, you will hear a voice message for testing the device
audio quality and volume.
Click on the Test Relay button to do a relay test.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Note
Operations Guide
You can change the SIP Volume, Multicast Volume, Ring Volume, and Sensor Volume
without rebooting the device. You must save and reboot the device for other changes to take
effect.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 48
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.5.1 Time Zone Strings
The posix time zone string tells the internal date and time utilities how to handle daylight savings
time for different time zones. The following table shows some common strings.
Table 2-12. Common Time Zone Strings
Time Zone
Time Zone String
US Pacific time
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Mountain time
MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Eastern Time
EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00
a
Phoenix Arizona
MST7
US Central Time
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
a.Phoenix, Arizona does not use daylight savings time.
The following table shows a breakdown of the parts that constitute the following time zone string:
●
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
Table 2-13. Time Zone String Parts
Operations Guide
Time Zone String
Part
Meaning
CST6CDT
The time zone offset from GMT and three character identifiers for the time zone.
CST
Central Standard Time
6
The (hour) offset from GMT/UTC
CDT
Central Daylight Time
M3.2.0/2:00:00
The date and time when daylight savings begins.
M3
The third month (March)
.2
The 2nd occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
M11.1.0/2:00:00
The date and time when daylight savings ends.
M11
The eleventh month (November)
.1
The 1st occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 49
Singlewire InformaCast Loudspeaker Amplifier Setup
Time Zone String
Examples
The following table has some more examples of time zone strings.
Table 2-14. Time Zone String Examples
Time Zone
Time Zone String
a
Tokyo
IST-9
Berlinb
CET-1MET,M3.5.0/1:00,M10.5.0/1:00
Adelaide, Australiac
ACST-9:30ACDT,M10.1.0/2:00:00,M4.1.0/2:00:00
a.Tokyo does not use daylight savings time.
b.For Berlin, daylight savings time starts on the last Sunday in March at
01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one
hour ahead of UTC.
c.Times for those in the Eastern Hemisphere need to have a negative time value.
Time Zone Identifier A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is
needed at the beginning of the posix time zone string to properly set the time. However, the specific
letters or numbers used for the time zone identifier are not important and can be any three or four
letter or number combination that is chosen by the user. However, the time zone identifier cannot be
blank.
You can also use the following URL when a certain time zone applies daylight savings time:
http://www.timeanddate.com/time/dst/2011.html
World GMT Table
The following table has information about the GMT time in various time zones.
Table 2-15. World GMT Table
Operations Guide
Time Zone
City or Area Zone Crosses
GMT-12
Eniwetok
GMT-11
Samoa
GMT-10
Hawaii
GMT-9
Alaska
GMT-8
PST, Pacific US
GMT-7
MST, Mountain US
GMT-6
CST, Central US
GMT-5
EST, Eastern US
GMT-4
Atlantic, Canada
GMT-3
Brazilia, Buenos Aries
GMT-2
Mid-Atlantic
GMT-1
Cape Verdes
GMT
Greenwich Mean Time, Dublin
GMT+1
Berlin, Rome
GMT+2
Israel, Cairo
GMT+3
Moscow, Kuwait
GMT+4
Abu Dhabi, Muscat
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 50
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-15. World GMT Table (continued)
Operations Guide
Time Zone
City or Area Zone Crosses
GMT+5
Islamabad, Karachi
GMT+6
Almaty, Dhaka
GMT+7
Bangkok, Jakarta
GMT+8
Hong Kong, Beijing
GMT+9
Tokyo, Osaka
GMT+10
Sydney, Melbourne, Guam
GMT+11
Magadan, Soloman Is.
GMT+12
Fiji, Wellington, Auckland
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 51
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.6 Configure the Network Parameters
1. Click the Network menu button to open the Network page (Figure 2-34).
Figure 2-34. Network Configuration Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 52
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Network page, enter values for the parameters indicated in Table 2-16.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-16. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking
the appropriate radio button. DHCP Addressing mode is enabled on
default and the device will attempt to resolve network addressing with
the local DHCP server upon boot. If DHCP Addressing fails, the
device will revert to the last known IP address or the factory default
address if no prior DHCP lease was established. See Section 2.3.1,
"Factory Default Settings" for factory default settings. Be sure to click
Save and Reboot to store changes when configuring a Static
address.
Hostname
This is the hostname provided by the DHCP server. See the
DHCP/DNS server documentation for more information. Enter up to
64 characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal
notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal
notation.
DHCP Timeout in seconds
Specify the desired time-out duration (in seconds) that the device will
wait for a response from the DHCP server before reverting back to
the stored static IP address. The stored static IP address may be the
last known IP address or the factory default address if no prior DHCP
lease was established. Enter up to 8 characters. A value of -1 will
retry forever.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
VLAN Priority (0-7)
Operations Guide
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of
0 may cause the VLAN ID tag to be ignored.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 53
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-16. Network Configuration Parameters (continued)
Web Page Item
Description
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 54
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.7 Configure the SIP (Session Initiation Protocol) Parameters
1. Click on the SIP menu button to open the SIP page (Figure 2-35).
Figure 2-35. SIP Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 55
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the SIP page, enter values for the parameters indicated in Table 2-17.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-17. SIP Page Parameters
Web Page Item
Description
SIP Settings
Enable SIP Operation
When enabled, the device will transmit, receive, and process SIP
messages according to the configured SIP settings below.
Register with a SIP Server
When enabled, the device will attempt to register to the configured SIP
Server(s) on this page. To configure the device to send and receive pointto-point SIP calls, enable SIP Operation and disable Register with a SIP
Server (see Section 2.3.7.2, "Point-to-Point Configuration").
Use Cisco SRST
When enabled, the backup servers are handled according to Cisco SRST
(Survivable Remote Site Telephony). It is required for use in clustered
Cisco Unified Communications Manager topologies.
Primary SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes
the host portion of the SIP-URI for the device's extension on the primary
SIP server. This field can accept entries of up to 255 characters in length.
Primary SIP User ID
Specify the SIP User ID for the Primary SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
primary SIP server. Enter up to 64 alphanumeric characters.
Primary SIP Auth ID
Specify the Authenticate ID for the Primary SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Primary SIP Auth Password
Specify the Authenticate Password for the Primary SIP Server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Server 1
Enter the backup SIP server address as an IPv4 address in dotted
decimal notation or a fully qualified domain name. This parameter also
becomes the host portion of the SIP-URI for the device's extension on the
backup SIP server. This field can accept entries of up to 255 characters in
length.
Backup SIP User ID 1
Specify the SIP User ID for the first backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
first backup SIP server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 1
Specify the Authenticate ID for the first backup SIP server. This parameter
is required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 1
Specify the Authenticate Password for the first backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Server 2
Enter a second backup SIP server address as an IPv4 address in dotted
decimal notation or a fully qualified domain name. This parameter also
becomes the host portion of the SIP-URI for the device's extension on the
second backup SIP server. This field can accept entries of up to 255
characters in length.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 56
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Backup SIP User ID 2
Specify the SIP User ID for the second backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
second backup SIP server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 2
Specify the Authenticate ID for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Auth Password 2
Specify the Authenticate Password for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the
destination port when sending SIP messages. The default Remote SIP
Port is 5060. The supported range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages. The default Local SIP Port is 5060. The supported range is 065536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address.
When an FQDN is configured, the device will run DNS NAPTR, SRV, and
A queries on the FQDN to resolve an IP address to which it will send all
SIP messages. This field can accept entries of up to 255 characters in
length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port
when sending SIP messages to the outbound proxy. A value of 0 will
default to 5060. The supported range is 0-65536. Enter up to 5 digits.
Disable rport Discovery
Disabling rport Discovery will prevent the device from including the public
WAN IP address and port number in the contact information that is sent to
the remote SIP servers. This will generally only need to be enabled when
using an SBC or SIP ALG in conjunction with a remote SIP server.
Buffer SIP Calls
Also referred to as delayed paging. Device will buffer up to 4 minutes of
audio then play back the recording after hang up.
Re-registration Interval (in seconds)
The SIP Re-registration interval (in seconds) is the SIP Registration lease
time, also known as the expiry. The supported range is 30-3600 seconds.
Enter up to 4 digits.
Unregister on Boot
When enabled, the device will send one registration with an expiry of 0 on
boot.
Keep Alive Period
The minimum time in milliseconds between keep-alive packets sent for nat
traversal. A value of 0 will disable keep alive packets.
SIP Strobe Settings
Blink Strobe on Ring
When selected, the Strobe will blink a scene when ringing.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 57
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when there is a SIP Call. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for SIP Call.
Green
The green LED value for SIP Call.
Blue
The blue LED value for SIP Call.
Use this button to preview the strobe flashing behavior for the MWI Strobe
Settings.
MWI Strobe Settings
Blink Strobe on MWI
When selected, the strobe will blink a scene when a voicemail is waiting
for its extension.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
MWI Call Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when there is a message waiting. This is
the maximum brightness for “fade” type scenes.
Red
The red LED value for MWI.
Green
The green LED value for MWI.
Blue
The blue LED value for MWI.
Use this button to preview the strobe flashing behavior for the MWI Strobe
Settings.
Nightringer Settings
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 58
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Enable Nightringer
When Nightringer is enabled, the device will attempt to register a second
extension with the SIP server. Any calls made to this extension will play a
ringtone (corresponds to Night Ring on the Audiofiles page). By design,
it is not possible to answer a call to the Nightringer extension.
SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes
the host portion of the SIP-URI for the device's Nightringer extension on
the SIP server. This field can accept entries of up to 255 characters in
length.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the
destination port when sending SIP messages for the Nightringer
extension. The default Remote SIP Port is 5060. The supported range is
0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages for the Nightringer extension. This value cannot be the same as
the Local SIP Port for the primary extension. The default Local SIP Port is
5061. The supported range is 0-65536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address for the
Nightringer extension. When an FQDN is configured, the device will run
DNS NAPTR, SRV, and A queries on the FQDN to resolve an IP address
to which it will send all SIP messages for the Nightringer extension. This
field can accept entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port
when sending SIP messages to the outbound proxy for the Nightringer
extension. A value of 0 will default to 5060. The supported range is 065536. Enter up to 5 digits.
User ID
Specify the SIP User ID for the SIP server. This parameter becomes the
user portion of the SIP-URI for the device's Nightringer extension. Enter
up to 64 alphanumeric characters.
Authenticate ID
Specify the Authenticate ID for the SIP Server. This parameter is required
for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Authenticate Password
Specify the Authenticate Password for the SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease
time, also known as the expiry. The supported range is 30-3600 seconds.
Enter up to 4 digits.
Nightringer Strobe Settings
Blink Strobe on Nightring
When selected, the Strobe will blink a scene when the Nightringer is
ringing.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 59
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when the Nightringer is ringing. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for Nightringer.
Green
The green LED value for Nightringer.
Blue
The blue LED value for Nightringer.
Use this button to preview the strobe flashing behavior for the Nightringer
Strobe Settings.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after establishing a SIP
call. This port number must be an even number and defaults to 10500.
The supported range is 0-65536. Enter up to 5 digits.
Jitter Buffer
Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid
values are 50-1000.
Call Disconnection
Terminate Call After Delay
Automatically terminate an active call after a given delay in seconds. A
value of 0 will disable this function. Enter up to 8 digits.
Codec Selection
Force Selected Codec
When configured, this option will allow you to force the device to negotiate
for the selected codec. Otherwise, the device will perform codec
negotiation using the default list of supported codecs.
Codec
Select the desired codec (only one may be chosen).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 60
Singlewire InformaCast Loudspeaker Amplifier Setup
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
For specific server configurations, go to the following website address:
https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers
2.3.7.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the SIP Page, dial out extensions support the addition of comma delimited pauses and sending
additional DTMF tones (using rfc2833). The first comma will pause three seconds after a call is first
established with a remote device. Subsequent commas will pause for 2 seconds. A pause of one
second will be sent after each numerical digit.
Table 2-18. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 64.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 61
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.7.2 Point-to-Point Configuration
When the device is set to not register with a SIP server (see Figure 2-36), it is possible to set the
device to dial out to a single endpoint.
In this case, the dial-out extension should be the IP address of the remote device. The device can
also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point
Mode.
Note
Receiving point-to-point SiP calls may not work with all phones.
Figure 2-36. SIP Page Set to Point-to-Point Mode
Device is set to NOT register with a SiP server
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 62
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.7.3 Delayed DTMF
On the SIP page the dial out extension supports the addition of comma delimited pauses and
sending additional DTMF tones (using rfc2833). The first comma will pause three seconds after a
call is first established with a remote device. Subsequent commas will pause for 2 seconds. A pause
of one second will be sent after each numerical digit.
Table 2-19. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 25.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 63
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.8 Configure the Multicast Parameters
The Multicast page allows the device to join up to ten paging zones for receiving ulaw/alaw encoded
RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3. The device
supports simultaneous SIP and Multicast.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 64
Singlewire InformaCast Loudspeaker Amplifier Setup
1. Click on the Multicast menu button to open the Multicast page. See Figure 2-37.
Figure 2-37. Multicast Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 65
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Multicast page, enter values for the parameters indicated in Table 2-20.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-20. Multicast Page Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Blink Strobe on Multicast
When selected, the Strobe will blink a scene when a multicast is
received.
Priority
Indicates the priority for the multicast group. Priority 9 is the
highest (emergency streams). 0 is the lowest (background
music). SIP calls are considered priority 4.5. See Section 2.3.8.1,
"Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15
character limit).
Port
Enter the port number for this multicast group (5 character limit
[range can be from 2000 to 65535]).
Note: The multicast ports have to be even values. The webpage
will enforce this restriction.
Name
Assign a descriptive name for this multicast group (25 character
limit).
Buffer
Device will buffer up to four minutes of audio and then play back
the recording after the multicast stream finishes or after the buffer
is full.
Beep
When selected, the device will play a beep before multicast audio
is sent.
Relay
When selected, the device will activate a relay before multicast
audio is sent.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then
OFF for 350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 3.5 seconds
during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 1.5 seconds
during the duration of the event.
Slow Blink
Strobe will blink ON at the specified brightness for one second
then OFF for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five
times per second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink on a multicast page. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for Multicast.
Green
The green LED value for Multicast.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 66
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-20. Multicast Page Parameters (continued)
Web Page Item
Description
Blue
The blue LED value for Multicast.
Polycom Default Channel
When a default Polycom channel/group number is selected, the
device will subscribe to the default channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Polycom Priority Channel
When a priority Polycom channel/group number is selected, the
device will subscribe to the priority channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Polycom Emergency Channel
When an emergency Polycom channel/group number is selected,
the device will subscribe to the default channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Use this button to preview the strobe flashing behavior for the
Multicast Strobe Settings.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web
page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.3.8.1 Assigning Priority
The device will prioritize simultaneous audio streams according to their priority in the list.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams, the volume is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 67
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.9 Configure the Sensor Page Parameters
The door sensor (pins 1 and 2) on the terminal block can be used to monitor a door's open or closed
state. There is an option on the Sensor Page to trigger on an open or short condition on these pins.
The door sensor alarm will be activated when the Sensor Timeout (in seconds) parameter has
been met.
Each sensor can trigger up to five different actions:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
•
Loop an audio file out of the speaker until the sensor is deactivated
•
Call an extension and establish two way audio
•
Call an extension and play a pre-recorded audio file
Note
Calling a preset extension can be set up as a point-to-point call, but currently can't send
delayed DTMF tones.
1. Click Sensor menu button to open the Sensor Page (Figure 2-38).
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 68
Singlewire InformaCast Loudspeaker Amplifier Setup
Figure 2-38. Sensor Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 69
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Sensor page, enter values for the parameters indicated in Table 2-21.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-21. Sensor Page Parameters
Web Page Item
Description
Sensor Settings
Sensor Normally Closed
Select the inactive state of the sensor. The sensor is also known
as the Sense Input on the device's terminal block.
Sensor Timeout (in seconds)
The time (in seconds) the device will wait before it performs an
action when the on-board door sensor is activated. The action(s)
performed are based on the configured Sensor Settings below.
Enter up to 5 digits.
Activate Relay
When selected, the device's on-board relay will be activated until
the on-board sensor is deactivated.
Play Audio Locally
When selected, the device will loop an audio file out of the
speaker until the sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the onboard door sensor is activated. Use the Dial Out Extension field
below to specify the extension the device will call.
Dial Out Extension
Specify the extension the device will call when the on-board
sensor is activated. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls.
Enter up to 64 alphanumeric characters.
Play recorded audio
When selected, the device will call the Dial Out Extension and
play an audio file to the phone answering the SIP call
(corresponds to Sensor Triggered on the Audiofiles Page
page).
Repeat Sensor Message
The number of times to repeat the audio message through the
local speaker or to the remote endpoint. A value of 0 will repeat
the message while the sensor is active. Enter a value from 065536.
Sensor Strobe Settings
Operations Guide
Blink Strobe on Sensor
When selected, the Strobe will blink a scene when the sensor is
triggered.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then
OFF for 350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 3.5 seconds
during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 1.5 seconds
during the duration of the event.
Slow Blink
Strobe will blink ON at the specified brightness for one second
then OFF for one second during the duration of the event.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 70
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-21. Sensor Page Parameters (continued)
Web Page Item
Description
Fast Blink
Strobe will blink ON at the specified brightness then OFF five
times per second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when the sensor is triggered. This
is the maximum brightness for “fade” type scenes.
Red
The red LED value for Sensor.
Green
The green LED value for Sensor.
Blue
The blue LED value for Sensor.
Click the Test Sensor button to test the sensor.
Use this button to preview the strobe flashing behavior for the
Sensor Strobe Settings.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web
page item.
Note
Operations Guide
You must click on the Save button for the changes to take effect.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 71
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.10 Configure the Audiofiles Page Parameters
The Audiofiles page is used to add custom audio to the board. User uploaded audio will take
precedence over the audio files shipped with the device.
1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-39).
Figure 2-39. Audiofiles Page
Singlewire V3.1 Paging Amplifier
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 72
Singlewire InformaCast Loudspeaker Amplifier Setup
Figure 2-40. Audiofiles Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 73
Singlewire InformaCast Loudspeaker Amplifier Setup
Figure 2-41. Audiofiles Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 74
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Audiofiles page, enter values for the parameters indicated in Table 2-22.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-22. Audiofiles Page Parameters
Web Page Item
Description
Available Space
Shows the space available for the user to save custom audio files if they want to change the
message when the door or sensor is triggered.
Stored Messages
Stored Message 1 through 9
Stored Message 1 corresponds to the message played after pressing 1 on a phone keypad.
Stored Message 2 corresponds to the message played after pressing 2 on a phone keypad.
Stored Message 3 corresponds to the message played after pressing 3 on a phone keypad.
Stored Message 4 corresponds to the message played after pressing 4 on a phone keypad.
Stored Message 5 corresponds to the message played after pressing 5 on a phone keypad.
Stored Message 6 corresponds to the message played after pressing 6 on a phone keypad.
Stored Message 7 corresponds to the message played after pressing 7 on a phone keypad.
Stored Message 8 corresponds to the message played after pressing 8 on a phone keypad.
Stored Message 9 corresponds to the message played after pressing 9 on a phone keypad.
Audio Files
0-4
The name of the audio configuration option is the same as the spoken audio that plays on
the board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
5-9
The name of the audio configuration option is the same as the spoken audio that plays on
the board (24 character limit).
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Corresponds to the spoken word “dot.” (24 character limit)
Audio Test
Corresponds to the message “This is the CyberData IP speaker test message...” (24
character limit)
Enter Code
Corresponds to the message “Enter Code” (24 character limit).
Invalid Code
Corresponds to the message “Invalid Code” (24 character limit).
Page Tone
Corresponds to a simple tone used for beep on initialization and beep on page (24 character
limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 75
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-22. Audiofiles Page Parameters (continued)
Web Page Item
Description
Restoring Default
Corresponds to the message “Restoring default” (24 character limit).
Ring Tone
This is the tone that plays when set to ring when receiving a call (24 character limit).
Sensor Triggered
Corresponds to the message “Sensor Triggered” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the same audio file that is
selected for the Ring Tone parameter.
Menu Audio Files
Menu Audio Files are user-uploadable messages that create the audio menu played to the
caller.
Cancel
Corresponds to the word "Cancel" used in the audio menu played to the caller. (24 character
limit).
Currently Playing
Corresponds to the words "Currently Playing" used in the audio menu played to the caller.
(24 character limit).
Invalid Entry
Corresponds to the words "Invalid Entry" used in the audio menu played to the caller. (24
character limit).
Page
Corresponds to the word "Page" used in the audio menu played to the caller. (24 character
limit).
Play Stored Message
Corresponds to the words "Play Stored Message" used in the audio menu played to the
caller. (24 character limit).
Pound (#)
Corresponds to whatever word or phrase the user wishes to call the pound key in the audio
menu played to the caller (24 character limit).
Press
Corresponds to the word "Press" used in the audio menu played to the caller. (24 character
limit).
Stored Message
Corresponds to the words "Stored Message" used in the audio menu played to the caller.
(24 character limit).
Through
Corresponds to the word "Through" used in the audio menu played to the caller. (24
character limit).
To
Corresponds to the word "To" used in the audio menu played to the caller. (24 character
limit).
Click on the Browse button to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the
file by using the Browse button. The Save button will delete any pre-existing user-uploaded
audio files.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 76
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.10.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-42 through
Figure 2-44.
Figure 2-42. Audacity 1
Figure 2-43. Audacity 2
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 77
Singlewire InformaCast Loudspeaker Amplifier Setup
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-44. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 78
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.11 Configure the Events Parameters
The Events page specifies a remote server that can be used to receive HTTP POST events when
actions take place on the board.
1. Click on the Events menu button to open the Events page (Figure 2-45).
Figure 2-45. Event Configuration Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 79
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Events page, enter values for the parameters indicated in Table 2-23.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-23. Events Configuration Parameters
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote
server and port number whenever a certain action takes place.
Select an event type below to generate an HTTP POST event.
Events
Enable Call Start Events
When selected, the device will report the start of a SIP call.
Enable Call Terminated Events
When selected, the device will report the end of a SIP call.
Enable Relay Activated Events
When selected, the device will report relay activation.
Enable Relay Deactivated Events
When selected, the device will report relay deactivation.
Enable Night Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call to the Nightringer extension. As a reminder, the
Nightringer extension always rings upon an incoming SIP call and it
is not possible to alter this behavior.
Enable Power On Events
When selected, the device will report when it boots.
Enable Multicast Start Events
When selected, the device will report when the device starts playing
a multicast audio stream.
Enable Multicast Stop Events
When selected, the device will report when the device stops playing
a multicast audio stream.
Enable Sensor Events
When selected, the device will report when the on-board sensor is
activated.
Enable 60 Second Heartbeat Events
When enabled, the device will report a Heartbeat event every 60
seconds. SIP registration is not required to generate Heartbeat
events.
Enable Singlewire Start Events
When selected, the device will report when a Start event has been
received from the Singlewire server.
Enable Singlewire Stop Events
When selected, the device will report when a Stop event has been
received from the Singlewire server.
Check All
Click on Check All to select all of the events on the page.
Uncheck All
Click on Uncheck All to de-select all of the events on the page.
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 065536. Enter up to 5 digits.
Server URL
Generally, the destination URL is the name of the application that
receives the events and the string in the HTTP POST command. It
can be a script used to parse and process the HTTP POST events.
Enter up to 127 characters.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 80
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-23. Events Configuration Parameters(continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question mark
to see a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 81
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.11.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 82
Singlewire InformaCast Loudspeaker Amplifier Setup
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 83
Singlewire InformaCast Loudspeaker Amplifier Setup
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 84
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.12 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-46.
Figure 2-46. Autoprovisioning Page
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 85
Singlewire InformaCast Loudspeaker Amplifier Setup
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 224.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-24. Autoprovisioning Configuration Parameters
Web Page Item
Description
Disable Autoprovisioning
Prevent the device from automatically trying to download a
configuration file. See Section 2.3.12.1, "Autoprovisioning" for
more information.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted
decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename.
The default autoprovisioning filename is in the format of
<mac address>.xml.
Supported filename extensions are .txt, and .xml. The current
filename is denoted by an asterisk at the bottom of the
Autoprovisioning Page. Enter up to 256 characters.
A file may have any name with an xml extension. If a file
name is entered, the device will look for the specified file
name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download
autoprovisioning files.
Username
The username used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Password
The password used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Autoprovisioning Autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before
checking for new autoprovisioning files. Enter up to 6 digits. A
value of 0 will disable this option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-11).
Autoprovision at time (HHMMSS)
The time of day the device will check for a new
autoprovisioning file. The time must be 6 characters in length
and in HHMMSS format. An empty value will disable this
option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-11).
The idle time (in minutes greater than 10) after which the
device will check for a new autoprovisioning file. Enter up to 6
digits. A value of 0 will disable this option.
Autoprovision when idle
(in minutes > 10)
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-11).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 86
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-24. Autoprovisioning Configuration Parameters (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a
specific web page item.
Press the Download Template button to create an
autoprovisioning file for the device. See Section 2.3.12.3,
"Download Template Button"
Autoprovisioning log
Note
The autoprovisioning log provides information about the latest
autoprovisioning attempt (i.e. dhcp options and server
accessed and files parsed or not found).
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.3.12.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.3.12.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 87
Singlewire InformaCast Loudspeaker Amplifier Setup
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-24). This file contains every configuration option that can
be set on the board.
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData Device</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
<!-<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<!-<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<!-<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 88
Singlewire InformaCast Loudspeaker Amplifier Setup
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 89
Singlewire InformaCast Loudspeaker Amplifier Setup
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-25. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 90
Singlewire InformaCast Loudspeaker Amplifier Setup
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 91
Singlewire InformaCast Loudspeaker Amplifier Setup
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 92
Singlewire InformaCast Loudspeaker Amplifier Setup
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 93
Singlewire InformaCast Loudspeaker Amplifier Setup
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio Configuration page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 94
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.12.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 95
Singlewire InformaCast Loudspeaker Amplifier Setup
2.3.12.3 Download Template Button
The Download Template button allows the user to generate, download, edit, and then store an
autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Download Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-47). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-47.
Figure 2-47. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 96
Singlewire InformaCast Loudspeaker Amplifier Setup
2.4 Upgrade the Firmware and Reboot the Singlewire
InformaCast Loudspeaker Amplifier
2.4.1 Downloading the Firmware
To download the firmware to your computer:
1. Download the latest firmware file from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011406
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the home page as instructed in Section 2.3.4, "Log in to the Configuration Home
Page".
4. Click on the Firmware menu button to open the Firmware page. See Figure 2-48.
Caution
GENERAL ALERT
Equipment Hazard: CyberData strongly recommends that you first reboot the
device before attempting to upgrade the firmware of the device. See Section 2.4.2,
"Reboot the Device".
Figure 2-48. Firmware Page
Singlewire V3.1 Paging Amplifier
v11.6.4
5. Click on the Browse button, and then navigate to the location of the firmware file.
6. Select the firmware file.
7. Click on the Upload button.
Note
Operations Guide
Do not reboot the device after clicking on the Upload button.
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 97
Singlewire InformaCast Loudspeaker Amplifier Setup
Note
This starts the upgrade process. Once the Singlewire InformaCast Loudspeaker Amplifier
has uploaded the file, the Uploading Firmware countdown page appears, indicating that
the firmware is being written to flash. The Singlewire InformaCast Loudspeaker Amplifier will
automatically reboot when the upload is complete. When the countdown finishes, the
Firmware page will refresh. The uploaded firmware filename should be displayed in the
system configuration (indicating a successful upload and reboot).
8. Table 2-26 shows the web page items on the Firmware page.
Table 2-26. Firmware Parameters
Web Page Item
Description
Current Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
firmware file that you want to upload.
Click on the Upload button to automatically upload the selected
firmware and reboot the system.
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 98
Singlewire InformaCast Loudspeaker Amplifier Setup
2.4.2 Reboot the Device
To reboot a Singlewire InformaCast Loudspeaker Amplifier, log in to the web page as instructed in
Section 2.3.4, "Log in to the Configuration Home Page".
1. Click on the Reboot button on the Home page (Figure 2-49). A normal restart will occur.
Figure 2-49. Home Page
406100001
v11.6.4
Reboot
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 99
Singlewire InformaCast Loudspeaker Amplifier Setup
2.5 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-27 use the free unix utility, wget, but any program that can send http POST
commands to the device should work.
2.5.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-27. Command Interface Post Commands
Device Action
HTTP Post Commanda
Trigger relay (for configured delay)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "test_relay=yes"
Place call to extension (example: extension 130)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "call=130"
Terminate active call
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "reboot=yes"
Test Audio button
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "test_audio=yes"
Announce IP address
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "speak_ip_address=yes"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_0=yes"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_1=yes"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_2=yes"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_3=yes"
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_4=yes"
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 100
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringtone=yes"
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_nightring=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_1=yes"
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 101
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringtone=yes"
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_nightring=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_1=yes"
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 102
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Delete the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_2=yes"
Delete the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_3=yes"
Delete the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_4=yes"
Delete the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_5=yes"
Delete the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_6=yes"
Delete the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_7=yes"
Delete the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_8=yes"
Delete the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_9=yes"
Delete the "Audio Test" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_audiotest=yes"
Delete the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_pagetone=yes"
Delete the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_youripaddressis=yes"
Delete the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_rebooting=yes"
Delete the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_restoringdefault=yes"
Delete the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_ringback=yes"
Delete the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_ringtone=yes"
Delete the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_nightring=yes"
Operations Guide
931281G
CyberData Corporation
Installing the Singlewire InformaCast Loudspeaker Amplifier 103
Singlewire InformaCast Loudspeaker Amplifier Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Trigger the Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/sensor.cgi" --post-data "test=yes"
a.Type and enter all of each http POST command on one line.
Operations Guide
931281G
CyberData Corporation
104
Appendix A: Mounting the Amplifier
A.1 Mount the Amplifier
Before you mount the enclosure, make sure that you have received all of the parts for each
enclosure. Refer to Table A-1.
Table A-1. Parts List
Operations Guide
Quantity
Part Name
1
Singlewire InformaCast Paging Amplifier Assembly
1
Enclosure
1
Installation Quick Reference Guide
1
PoE Power Injector
1
CAT 5e/CAT6 cable
1
Ground Wire
931281G
Illustration
CyberData Corporation
105
Mount the Amplifier
Table A-1. Parts List (continued)
Quantity
Part Name
1
Mounting Accessory Kit which includes:
Illustration
(4) #8 Plastic Anchors
(4) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
#8 x 1.25" Pan Head
Phillip Drive
Self-Tapping Screw (4x)
#8 Plastic Tri-Lobe
Light Duty Anchor (4x)
Operations Guide
1
IEC Power Cord
1
Universal Receptacle
Note
The Singlewire InformaCast Loudspeaker Amplifier was designed for indoor use. Mounting it
on the external part of a building will require additional hardware for weatherproofing,
cabling access, and lightning suppression. Consult a certified electrician for details.
Note
For mounting, use the three #8 SHEET METAL SCREWS to secure the enclosure.
931281G
CyberData Corporation
106
Mount the Amplifier
A.1.1 Mounting the Enclosure
To mount the enclosure:
1. Prepare holes for the screws.
2. Plug in the power adapter and use the Power (PWR) LED to verify that the power is on.
3. Plug the ethernet cable into the device. The Link/Activity (Link/Act.) LED verifies the network
connection.
4. For wall mounting, use the three #8 x 1-1/4-inch Truss Head Phillip screws to secure the
speaker. See Figure A-1.
Figure A-1. Mounting the Enclosure
151147
#8x1.25" Truss Head Phillips
Sheet Metal Screw (3x)
531032
Plastic Ribbed Anchor (3x)
Wiring the 125V AC Plug
Caution
GENERAL ALERT
Operations Guide
Equipment Caution: The green wire with the yellow stripe is a ground connection
for Electrostatic Discharge (ESD) protection, and should not be removed. 
To wire the 125V AC plug, consult a licensed electrician and the local building
codes in your area.
931281G
CyberData Corporation
107
Appendix B: Setting up a TFTP Server
B.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
B.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
https://www.cyberdata.net/pages/solarwinds
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
931281G
CyberData Corporation
108
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
To see a list of frequently asked questions for your product, click on the FAQs tab at the following
webpage:
https://www.cyberdata.net/products/011406
C.2 Documentation
The documentation for this product is released in an English language version only.
To download PDF copies of CyberData product documentation, click on the Downloads tab at the
following webpage:
https://www.cyberdata.net/products/011406
Operations Guide
931281G
CyberData Corporation
109
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601, Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Extension 333
C.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
Operations Guide
931281G
CyberData Corporation
110
Index
backups 55
boost (volume) 44
Symbols
#6 sheet metal screws 105
C
Numerics
cabling 29
changing
the web access password 43
Cisco SRST 55
command interface 99
commands 99
components 13
configurable parameters 44, 52, 55
configuration
audio 71
default IP settings 35
door sensor 67
intrusion sensor 67
network 51
SIP 54
configuration home page 39
configuration page
configurable parameters 44, 52
connecting the amplified outputs 22
connection options 24
connections 13, 24
connections inside of the NEMA box 13
contact information 109
contact information for CyberData 109
current network settings 52
CyberData contact information 109
1 speaker configuration 22, 23
125V AC Plug (wiring) 106
2 speaker configuration 23
802.3af mode 22, 23
802.3at compliance switch 22, 23
802.3at mode 23
802.3at power injector (high power mode) 22, 23
A
ac plug (wiring) 106
accessory kit 10, 105
activate relay (door sensor) 69
activity LED 30
address, configuration login 39
amplified outputs 22, 23
high power mode 23
how to use and connect 22
low power mode 22
announcing an IP address 31
audio configuration 71
night ring tone parameter 75
audio encodings 4
audio files, user-created 76
audio page 71
audio test 31
autoprovision at time (HHMMSS) 85
autoprovision when idle (in minutes > 10) 85
autoprovisioning 86
download template button 86
autoprovisioning autoupdate (in minutes) 85
autoprovisioning configuration 84, 85
autoprovisioning filename 85
autoprovisioning server (IP Address) 85
D
default
gateway 11, 35
IP address 11, 35
subnet mask 11, 35
username and password 11, 35
web login username and password 39
default gateway 11, 35, 52
default IP settings 35
default login address 39
device configuration 43
device configuration parameters 85
the device configuration page 84
device configuration page 43
device configuration parameters 44
B
backup SIP server 1 55
backup SIP server 2 55
backup SIP servers, SIP server
Operations Guide
931281G
CyberData Corporation
111
device configuration password
changing for web configuration access 43
DHCP Client 4
dial out extension (door sensor) 69
dial out extension strings 60
dial-out extension strings 62
dimensions 5
disable volume control dial 44
discovery utility program 39
distortion, total harmonic 5
DNS server 52
door sensor 67, 75
activate relay 69
dial out extension 69
door sensor normally closed 69
play audio locally 69
download autoprovisioning template button 86
DTMF tones 60, 62
DTMF tones (using rfc2833) 60
http web-based configuration 4
E
J
enable night ring events 79
enclosure, mounting 104
ethernet I/F 5
event configuration
enable night ring events 79
expiration time for SIP server lease 56, 58
export settings 41, 42
jumper descriptions 28
jumper locations 28
I
identifier names (PST, EDT, IST, MUT) 49
identifying your product 1
illustration of amplifier mounting process 104
import settings 41, 42
import/export settings 41, 42
input specifications 5
installation 2
IP address 11, 35, 52
IP address announcement 31
IP address confirmation 31
IP addressing
default
IP addressing setting 11, 35
L
lease, SIP server expiration time 56, 58
LEDs 30
lengthy pages 66
line input specifications 5
line output specifications 5
Linux, setting up a TFTP server on 107
local SIP port 56
log in address 39
loudspeaker type 29
loudspeaker, cabling/wiring 29
low power mode (amplified outputs) 22
F
factory defaults 12, 31
firmware
where to get the latest firmware 96
G
get autoprovisioning template 86
GMT table 49
GMT time 49
M
MGROUP
MGROUP Name 65
mounting an amplifier 104
multicast configuration 63, 71
Multicast IP Address 65
H
harmonic distortion 5
hazard levels 4
high power mode (amplified outputs) 23
home page 39
http POST command 99
Operations Guide
931281G
CyberData Corporation
112
N
product features 3
product specifications 5
supported protocols 4
supported SIP servers 4
typical system installation 2
product specifications 5
protocols supported 4
navigation (web page) 36
navigation table 36
NEMA box components 13
network configuration 51
network link activity, verifying 30
nightring tones 66
Nightringer 95
nightringer settings 57
NTP server 44
R
reboot 97, 98
remote SIP port 56
reset test function management switch 31
resetting the IP address to the default 104
restoring the factory defaults 12, 31
ringtones 66
lengthy pages 66
rport discovery setting, disabling 56
RTFM switch 12, 31
RTP/AVP 4
O
one speaker configuration 22, 23
optional two speaker configuration 23
output impedance 5
output level 5
output signal amplitudes 5
output specifications 5
S
P
safety instructions 5
sales 109
sensor
sensor normally closed 69
sensor timeout 69
sensor connection 25
sensor setup page 68
sensor setup parameters 67
sensors 69
server address, SIP 55
service 109
set time with external NTP server on boot 44
SIP
enable SIP operation 55
local SIP port 56
user ID 55
SIP (session initiation protocol) 4
SIP configuration 54
SIP configuration parameters
outbound proxy 56, 58
registration and expiration, SIP server lease 56, 58
unregister on reboot 56
user ID, SIP 55
SIP registration 55
SIP remote SIP port 56
SIP server 55
password for login 55
SIP servers supported 4
unregister from 56
packet time 4
pages (lengthy) 66
parts list 9, 104
password
for SIP server login 55
login 39
restoring the default 11, 35
payload types 5
play audio locally (door sensor) 69
point-to-point configuration 61
polycom default channel 66
polycom emergency channel 66
polycom priority channel 66
port
local SIP 56
remote SIP 56
posix timezone string
timezone string 44
POST command 99
power input 5
power LED 12, 30
power, connecting to paging amplifier 22
priority
assigning 66
product
mounting 104
parts list 9
product features 3
product overview
Operations Guide
931281G
CyberData Corporation
113
W
user ID for login 55
SIP server configuration 55
SIP volume 44
speaker cable 29
speaker configuration 22, 23
speaker configuration for two speakers 23
speaker wire 29
SRST 55
standard 1 speaker configuration 22, 23
status LED 12, 30
subnet mask 11, 35, 52
supported protocols 4
warranty policy at CyberData 109
web access password 11, 35
web access username 11, 35
web configuration log in address 39
web page
navigation 36
web page navigation 36
wget, free unix utility 99
Windows, setting up a TFTP server on 107
wiring 29
wiring (ac plug) 106
T
tech support 109
technical support, contact information 109
test audio 31
TFTP server 4, 107
time zone string examples 49
two speaker configuration 23
U
user ID
for SIP server login 55
username
changing for web configuration access 43
default for web configuration access 39
restoring the default 11, 35
using the amplified outputs 22
V
verifying
network link and activity 30
power on 30
VLAN ID 52
VLAN Priority 52
VLAN tagging support 52
VLAN tags 52
volume 34
multicast volume 44
ring volume 44
sensor volume 44
SIP volume 44
volume adjustment 32
volume boost 44
volume control dial
disable 44
volume dial 34
Operations Guide
931281G
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising