CyberData | 011407 | Quick Reference | Cyberdata 011407 InformaCast® Enabled Loudspeaker Amplifier (PoE) Quick Reference

Cyberdata 011407 InformaCast® Enabled  Loudspeaker Amplifier (PoE) Quick Reference
Mounting the Enclosure
Installation Quick Reference
To mount the enclosure:
1. Prepare holes for the screws.
The IP Endpoint Company
2. Plug in the power adapter and use the
Power (PWR) LED to verify that the
power is on.
Singlewire InformaCast
Loudspeaker Amplifier (PoE)
SIP Compliant
011407
3. Plug the ethernet cable into the device.
The Link/Activity (Link/Act.) LED
verifies the network connection.
4. For wall mounting, use the three
#8 x 1-1/4-inch Pan Head Phillips
Self-Tapping Screws.
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
a
Subnet Mask
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Getting Started
•
Download the Operations Guide PDF file from the Documents tab at the following webpage:
http://www.cyberdata.net/voip/011407/
•
Create a plan for the locations of your paging amplifiers.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: The Singlewire InformaCast Loudspeaker Amplifier enclosure is not rated for any AC voltages!
Parts
(1) Assembly
(1) Wall Mounting Kit
(3) #8 Plastic Anchors
(3) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
Contacting CyberData
(1) Enclosure
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931275C
Additional Parts
(1) CAT 5e/CAT6 cable
Quick Reference
Quick Reference
931275C
(1) PoE Power Injector
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Features
Dimensions and Mounting Template
RTFM Switch
VoIP
Loudspeaker
6.281 [159.54]
Dimensions are in Inches [Millimeters]
To broadcast the device’s current IP address, press and hold the RTFM switch for a couple
of seconds and then release it.
To restore the factory defaults, complete the following steps:
RTFM
1. Press and hold the RTFM switch until you hear the device announce the words,
“restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the factory default settings.
Speaker Volume
Volume
Speed (SPD) LED (AMBER)
The Speed (SPD) LED illuminates AMBER for a 100Mb link
or is off for a 10MB link when the network link to the device is established.
SPD Link/Act.
14.500
[368.30]
Link/Activity (Link/Act.) LED (GREEN)
The GREEN Link/Activity (Link/Act.) LED blinks to indicate network traffic.
7.938
[201.63]
PWR Status
Status LED (GREEN)
The GREEN Status LED illuminates after supplying power to the device.
Power (PWR) LED (GREEN/BLUE)
The Power (PWR) LED is GREEN in low power mode (802.3af)
and BLUE during high power mode (802.3at).
10.875 [276.23]
Dimensions are in Inches [Millimeters]
*See the Operations Guide for more information about the features in this section.
4.375
[111.13]
Cable Grommets (3 PLCS)
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931275C
Quick Reference
Quick Reference
931275C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising