CyberData | 011442 | Datasheet | Cyberdata 011442 Flush Mount Kit, 2x Datasheet

Cyberdata 011442 Flush Mount Kit, 2x Datasheet
Flush Mount Kit, 2X
The IP Endpoint Company
The CyberData Flush Mount Kit is a bezel kit
that turns the CyberData 2X Outdoor
Intercoms and Security Access Endpoint
products into a flush-mounted installation.
Features

Mounting kit can be used to adapt an
intercom to drywall, stucco, masonry, and
wood structures

Provides greater security to prevent
vandalism


Same rugged design as our outdoor
Specifications
faceplates use
Dimensions*
9.94 inches [252.5 mm] Length
0.06 inches [1.52 mm] Width
7.56 inches [192 mm] Height
Weight
Boxed Weight
0.87 pounds [1.92 kg]
1.13 pounds [2.49 kg]
Compliance
RoHS
Warranty
2 Years Limited
Part Number
011442
Stainless steel construction
*Dimensions are measured from the perspective of the product
being upright with the front of the product facing you.
Related Products:
011214 SIP Outdoor
Intercom with Keypad
CyberData Corporation
011414 SIP h.264 Video
Outdoor Intercom with Keypad

3 Justin Court, Monterey, CA 93940

831.373.2601
011310 Singlewire InformaCast
Outdoor Intercom with Keypad

Fax: 831.373.4193

www.cyberdata.net
Flush Mount Kit, 2X
Typical Installation
Drywall / Concrete / Brick
Plastic Anchors
Drywall / Concrete / Brick
Ground
Lug
Ground
Lug
Faceplate Assembly
Backbox
Backbox
See Note
Inner Mount
Tool Required:
Prepare Holes for Plastic Anchors
Drill Hole Size to: 0.1875" / 3/16" / 4.8 mm
Insert Provided Plastic Anchor (4 Pieces)
into Drywall with a Hammer Until
End of Anchor Flush with the Drywall Surface
Prepare Hole Cutout on Drywall
Hole Size: 7.8" (Width) x 5.3" (Height) /
Hole Size: 198mm (Width) x 135mm (Height)
Place Inner Mount Over Wall Cutout
Mark Hole Center with Pencil / Marker
1) Pencil / Marker
2) Phillip Drive Screw Driver / Power Tool with Bit
3) A Hammer / Rubber Mallet
4) 3/16" / 4.8mm Drill Bit (Use Correct Drill Bit for Drywall / Concrete)
5) T-15 Tamper-Resistant Torx Driver (Comes with Outdoor Intercom)
6) 5/16" / 8mm Wrench / Drive Socket to Remove Gound Lug (Nut)
7) 11/32" / 9mm Wrench / Drive Socket to Remove Hole Plug Assembly (Nut)
8) Weatherproofing Silicone Sealant (Optional)
Install Ground Wire to Ground Lug
Install Inner Mount with Provided
Flat Head Undercut Machine Screw (4 Pieces)
to Backbox
Remove Faceplate Assembly from Backbox
Save Mounting Screw for Later Use
Note:
Remove Hole Plug Assembly from Backbox
If Wire and Cable are Come in from Side
Mounting Screw
(Tamper-Resistant Torx Screw Shown)
*
Flange Gasket
Mount +
Flange
Mount
Gasket
Drywall / Concrete / Brick
Faceplate Assembly
Mounting Screw
Adhere Provided Gasket on to the Back of Flange Mount
or Weatherproofing Silicone Sealant (Not Provided)
Insert Backbox with Inner Mount Assembly
into Drywall/Concrete/Brick Wall Cutout
with Provided Flat Head Self-tapping Screw (4 Pieces)
*
CyberData Corporation

3 Justin Court, Monterey, CA 93940

831.373.2601

Fax: 831.373.4193

www.cyberdata.net
931591A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising