CyberData | 011474 | Setup guide | Cyberdata **NEW RELEASE** 011474 Cisco 8851/61 Secure Phone Case Setup Guide

Cyberdata **NEW RELEASE** 011474 Cisco 8851/61 Secure Phone Case Setup Guide
CP-8851 / CP-8861
Do Not Ship Enclosure with Phone Installed
[PHONE MUST BE INSTALLED ON-SITE]
CP-8851 / 9961 Mounting the Enclosure
Take into consideration before you install:
- Due to the size and mass of this product, it is
important that the Backbox is safely installed
according to these installation instructions.
- Make sure that the type of wall is capable of supporting
the system and use screws that are suitable for that type of wall.
- The system must be installed by qualified personnel, in
accordance with state and local building regulations.
- See sheet five and ten for Conduit and Wall Mounting instructions.
Accessory Kits
#6-32 x 3/16”
Button Head Torx
Smaller Machine Screw
Hex L-Key
(Spare)
for Acrylic Bezel
Replacement
Jumper Shunt
Drilled Spanner Dirver Bit
Coverplate
#8 Hex Nut
(GND Lug)
Mounting
Screw
#6-32x5/8"Flat Head
Pin Torx Machine Screw
(Spare - 2 Pieces)
Keypad Cover Accessory Kit
Torx Sec. Bit & Spare Screw Kit
#00 Screw Driver Kit
T-15 Pin Torx
Security Driver Bit
Phone Mounting Screw Kit
Remove Handset, USB & KEM Covers,
Install all Cables then the Mounting Bracket
Remove Handset &
Disconnect Cord from Phone.
Then Connect Power Plug (1) &
Network Cable (2), etc. before
Install Mounting Bracket
Cisco CP-8851 /
Cisco CP-8861
(2)
Mounting
Screw (2 Pieces)
(1)
Remove Both
USB & KEM
Covers
Mounting
Bracket
Plug in the USB Cable
AUX
USB Port
USB-B Plug in to
USB to Analog Audio Module
(See Sheet 6 of 10)
Right Angle
USB-A Plug
AUX
Cable
Mount the Backbox Assembly
to the Wall
Figure Shown Typical Installation:
Tools Required:
1) Electric Powered Hand Drill
2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)
3) Leveler
4) Torque Wrench, Wrench and Socket
Step 3
A) Prepare Hole on Drywall (with Stud Behind) / Concrete
B) Insert Stud Anchors in to Holes
C) Align Backbox Assembly Mounting Holes to Studs
D) Tighten Washers and Nuts that included with Stud Anchors
E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.
Hookswitch Cradle to Handset Connections
Use Provided #00 Screw Driver
to Install Wires to Terminal Block
Hookswitch Cradle
USB to Analog
Audio Module
Terminal
Block
10
Black Wire to Terminal 4
Green Wire to Terminal 3
Yellow Wire to Terminal 2
Red Wire to Termianl 1
Black Wire
USB-B
Black Wire
Red Wire
to Terminal 5
Factory Disconnected,
Connect Before Closing the Faceplate
1
Armored Cord
Handset Lanyard
Black Wire
to Terminal 9
Armored Cord
Handset Retainer
Install Shunt on JP2
to Enable Auto Answer Mode
Shunt
JP2
Phone with
Phone Mount
Backbox
Assembly
Intall Phone with Phone Mount
to Backbox
Use Provided Security Torx
Driver Bit to Fasten Screws
to Backbox
Tool Required:
Electric Hand Drill or
Powered Screwdriver
Torx Screw (11x)
Faceplate
Assembly
Backbox
Assembly
Dimensions and Features
Security Torx Screw
(Included Two Spare & Torx Driver Bit)
Hookswitch Coverplate
Available for Handsfree
Operation, P/N: 611535A
2.874 [73.0]
Ø0.512 [Ø13.0]
(2 Places)
Customer Replaceable
Scratch Resistance Acrylic
P/N: 621028A
4.724 [120.0]
Customer Replaceable
Armored Cord Handset with
Steel Lanyard
P/N: 031433D
Customer Replaceable
304 Stainless Steel Faceplate
P/N: 611578A
Ø0.315 [Ø8.0]
(6 Places)
15.197 [386.0]
Hole Diameter fits 1/4” -20 Thread Size
Stud Anchors/Screw/Bolt
4.724 [120.0]
Included Keypad Coverplate,
Screw and Hex L-Key
(for Handsfree Operation)
SPAR II (for Use with
Biometric / RFID)
RTFM Access Hole Covered
by Security Torx Screw
3.130 [79.5]
Ø0.827 [Ø21.0]
Fits 1/2" EMT
Connector & Conduit
Coverplate Pre-Installed
To Remove Nut Behind:
Use 1/4” / 6mm Socket
Reserved for Biometric Reader /
RFID Reader Module Upgrade
2.087 [53.0]
APPROX. 6.040 [153.4]
12.992 [330.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
4.331 [110.0]
8.661 [220.0]
1.996 [50.7]
Tool Required to Remove Hole Plug:
1) 11/32" or 9mm Socket & Socket Wrench
1.526 [38.8]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising