CyberData | 011244 | Quick Start Guide | Cyberdata 011244 Singlewire InformaCast Strobe (Replacement Product Below) Quick Start Guide

Cyberdata 011244 Singlewire InformaCast Strobe (Replacement Product Below) Quick Start Guide
V3 Strobe, Singlewire
Quick Start Guide
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide,
which is available on the Documentation page. You can navigate to the
Documentation page by going to www.CyberData.net and following the
steps that are indicated by the following figures:
1
2
3
2.0 Select Power Source
PoE Switch
PoE Injector
Set PoE power type to Class 0 = 13W
CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
Quick Start Guide
930643A
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity above the
ethernet port on the back of the V3 Strobe. See the following figure:
3.2. The GREEN Link LED blinks off once during the boot up process and then
comes on again and remains constant (solid GREEN). The YELLOW
Activity LED may be blinking depending on the network activity.
Normally, this process will take about 30 seconds. However, if no DHCP is
available, then this process could take up to 2 minutes.
This concludes the power test. Go to Section 4.0, "InformaCast
Configuration File Retrieval".
Quick Start Guide
930643A
4.0 InformaCast Configuration File Retrieval
4.1. DHCP should be enabled. After the device initializes, it will send a
broadcast to the DHCP server to ask for the location of its
InformaCastdevice.cfg configuration file.
4.2. SLP or TFTP?
•
SLP should be enabled on InformaCast version 5.0.4 or higher. SLP is an
InformaCast protocol introduced in InformaCast version 5.0.4. The device
will retrieve its configuration file from an InformaCast server folder specified
by SLP. SLP method is preferred.
•
TFTP servers may be used instead of SLP. In this alternate scenario, DHCP
option 150 is required to provide the device with the address of the TFTP
server. Otherwise, the device will be unable to retrieve its configuration file.
Note The CyberData device and the InformaCast server should be on
the same subnet during the device's initial configuration if it cannot
access the VLANs upon which the InformaCast Server and DHCP
servers are located.
5.0 Singlewire-Enabled V3 Strobe Identification and
Testing
5.1. Ensure the InformaCast Server has detected a new device.
5.2. Test the newly detected device.
5.3. Add the newly detected device to the InformaCast Server.
Quick Start Guide
930643A
6.0 Contacting CyberData VoIP Technical Support
For quality assurance purposes, we ask that you please visit our website and
complete our Support Form. Navigate through the menus to the Support Form as
shown in the following figure:
The Support Form initiates a ticket which CyberData uses for tracking customer
requests. Most importantly, the Support Form tells us which PBX system and
software version that you are using, the make and model of the switch, and other
important information. This information is essential for troubleshooting. Please
also include as much detail as possible in the Comments section of the Support
Form.
Requests for Returned Materials Authorization (RMA) numbers require an active
VoIP Technical Support ticket number. A product will not be accepted for return
without an approved RMA number.
Quick Start Guide
930643A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising