CyberData | 011244 | Operations Guide | Cyberdata 011244 Singlewire InformaCast Strobe (Replacement Product Below) Operations Guide

Cyberdata 011244 Singlewire InformaCast Strobe (Replacement Product Below) Operations Guide
The IP Endpoint Company
Singlewire Strobe
Operations Guide
Part #011244
Document Part #930829D
for Firmware Version 11.1.0
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
Singlewire Strobe Operations Guide 930829D
Part # 011244
COPYRIGHT NOTICE:
© 2015, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://www.cyberdata.net/support/contactsupportvoip.html


Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
CyberData Corporation
930829D
Operations Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The Singlewire Strobe enclosure is not rated for any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
CyberData Corporation
930829D
Operations Guide
Pictorial Alert Icons
GENERAL ALERT
General Alert
This pictorial alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
Ground
This pictorial alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
CyberData Corporation
930829D
Operations Guide
Abbreviations and Terms
Abbreviation or Term
Definition
A-law
A standard companding algorithm, used in European digital
communications systems to optimize, i.e., modify, the dynamic range of an
analog signal for digitizing.
AVP
Audio Video Profile
Cat 5
TIA/EIA-568-B Category 5
DHCP
Dynamic Host Configuration Protocol
LAN
Local Area Network
LED
Light Emitting Diode
Mbps
Megabits per Second.
NTP
Network Time Protocol
PBX
Private Branch Exchange
PoE
Power over Ethernet (as per IEEE 802.3af standard)
RTFM
Reset Test Function Management
SIP
Session Initiated Protocol
u-law
A companding algorithm, primarily used in the digital telecommunication
UC
Unified Communications
VoIP
Voice over Internet Protocol
CyberData Corporation
930829D
Operations Guide
Revision Information
Revision 930829D, which corresponds to firmware version 11.1.0, and was released on January 19,
2015, has the following changes:
•
Updates Figure 2-12, "Home Page"
•
Updates Figure 2-13, "Device Configuration Page"
•
Updates Figure 2-15, "Strobe Configuration Page"
•
Updates Figure 2-16, "Network Configuration Page"
•
Updates Figure 2-17, "SIP Configuration Page"
•
Updates Figure 2-18, "SIP Page Set to Point-to-Point Mode"
•
Updates Figure 2-19, "Multicast Configuration Page"
•
Updates Figure 2-20, "Sensor Configuration Page"
•
Updates Figure 2-21, "Audiofiles Configuration Page"
•
Updates Figure 2-25, "Event Configuration Page"
•
Updates Figure 2-26, "Autoprovisioning Page"
•
Updates Figure 2-28, "Firmware Page"
•
Updates Figure 2-29, "Reboot System Section"
•
Updates Table 2-7, "Web Page Navigation"
•
Updates Table 2-8, "Home Page Overview"
•
Updates Table 2-9, "Device Configuration Parameters"
•
Updates Table 2-15, "Network Configuration Parameters"
•
Updates Table 2-16, "SIP Configuration Parameters"
•
Updates Table 2-19, "Multicast Configuration Parameters"
•
Updates Table 2-20, "Sensor Configuration Parameters"
•
Updates Table 2-21, "Audiofiles Configuration Parameters"
•
Updates Table 2-22, "Events Configuration Parameters"
•
Updates Table 2-23, "Autoprovisioning Configuration Parameters"
•
Updates Table 2-25, "Firmware Parameters"
•
Updates Table 2-26, "Command Interface Post Commands"
Browsers Supported
The following browsers have been tested against firmware version 11.1.0:
CyberData Corporation
•
Internet Explorer (version: 10)
•
Firefox (also called Mozilla Firefox) (version: 23.0.1 and 25.0)
•
Chrome (version: 29.0.1547.66 m)
•
Safari (version: 5.1.7)
930829D
Operations Guide
i
Contents
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................3
1.4 Supported Protocols .................................................................................................................3
1.5 Product Specifications ..............................................................................................................4
1.6 Dimensions ...............................................................................................................................5
Chapter 2 Installing the Singlewire Strobe
6
2.1 Parts List ..................................................................................................................................6
2.1 Singlewire Strobe Setup ...........................................................................................................7
2.1.1 Singlewire Strobe Connections ......................................................................................7
2.1.2 Connecting the Singlewire Strobe to the Auxiliary Relay ...............................................8
2.1.3 Identifying the Singlewire Strobe Connectors and Jumpers .........................................10
2.1.4 Link and Activity LEDs .................................................................................................13
2.1.5 Restore the Factory Default Settings ...........................................................................14
2.2.1 Factory Default Settings ...............................................................................................15
2.2.2 Singlewire Strobe Web Page Navigation ......................................................................16
2.2.3 Using the Toggle Help Button .......................................................................................17
2.2.4 Log in to the Configuration Home Page .......................................................................19
2.2.5 Configure the Device ....................................................................................................23
2.2.6 Configure the Strobe ....................................................................................................28
2.2.7 Configure the Network Parameters .............................................................................32
2.2.8 Configure the SIP Parameters .....................................................................................35
2.2.9 Configure the Multicast Parameters .............................................................................42
2.2.10 Configure the Sensor Configuration Parameters ........................................................44
2.2.11 Configure the Audio Configuration Parameters ..........................................................47
2.2.12 Configure the Event Parameters ................................................................................50
2.2.13 Configure the Autoprovisioning Parameters ...............................................................55
2.3.1 Reboot the Device ........................................................................................................69
2.4.1 Command Interface Post Commands ..........................................................................70
Appendix A Mounting the Singlewire Strobe
71
A.1 Mount the Singlewire Strobe .................................................................................................71
Appendix B Troubleshooting/Technical Support
76
B.1 Frequently Asked Questions (FAQ) ........................................................................................76
B.2 Documentation .......................................................................................................................76
B.3 Contact Information ................................................................................................................77
B.4 Warranty .................................................................................................................................78
B.4.1 Warranty & RMA Returns within the United States ......................................................78
B.4.2 Warranty & RMA Returns Outside of the United States ..............................................78
B.4.3 Spare in the Air Policy ..................................................................................................79
B.4.4 Return and Restocking Policy ......................................................................................79
B.4.5 Warranty and RMA Returns Page ................................................................................79
Index
Operations Guide
80
930829D
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the Singlewire Strobe, look for a model number label similar to the one 
shown in Figure 1-1. Confirm the following:
●
The model number on the label should be 011244.
●
The revision letter of the model number should be B or higher.
●
The serial number on the label should begin with 2441.
Figure 1-1. Model Number Label
WWW.CYBERDATA.NET
SINGLEWIRE STROBE
RAL 9003 RoHS
011244B / 021105H
244100001
Model number
Operations Guide
Revision letter should be B or higher
930829D
Serial number begins with 0871
CyberData Corporation
Product Overview 2
Typical System Installation
1.2 Typical System Installation
Figure 1-2 illustrate how the Singlewire Strobes can be installed as part of a VoIP phone system.
Figure 1-2. Typical Installation
Generic PoE Switch
1
Singlewire Strobe
Singlewire Strobe
2
3
4
Singlewire Strobe
5
6
IP Phone
IP PBX Server
Warning
Electrical Hazard: The Singlewire Strobe enclosure is not rated for any AC
voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
Operations Guide
930829D
CyberData Corporation
Product Overview 3
Product Features
1.3 Product Features
●
Compatible with Singlewire InformaCast
●
Meets ADA requirements for telephony signalling and notification
●
Web-based setup
●
PoE-powered
1.4 Supported Protocols
The Singlewire Strobe supports:
●
HTTP Web-based configuration
Provides an intuitive user interface for easy system configuration and verification of Singlewire
Strobe operations.
●
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
●
RTP
●
RTP/AVP - Audio Video Profile
●
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
Packet Time 20 ms
Operations Guide
930829D
CyberData Corporation
Product Overview 4
Product Specifications
1.5 Product Specifications
Table 1-1. Specifications
Category
Specification
Ethernet I/F
10/100 Mbps
Power Input
PoE 802.3af compliant 
or 8 to 12 VDC at 1000 mA
Protocol
InformaCast v4.0 and later
Light power
90 candela (5-Watt LEDs)
Flash rate
2 per second
LED MTBF
100,000 Hours
Operating Temperature
-10o C to 50o C (14o F to 122o F)
Dimensions
4.5” x 4.5” x 1.5” (H x W x D)
Warranty
2 years limited
Power Requirement
802.3af compliant 
or 8 to 12 VDC at 1000 mA
Auxiliary Relay
1A at 30 VDC
Weight
1.6 lbs./shipping weight of 2.2 lbs.
(0.7 kg/shipping weight of 1.0kg)
Part Number
Operations Guide
011244
930829D
CyberData Corporation
Product Overview 5
Dimensions
1.6 Dimensions
4.5 [115]
Figure 1-3. Dimensions—Size of Unit with Case
2.1 [55]
4.5 [115]
DIMENSIONS ARE IN INCHES [MILLIMETERS]
Operations Guide
930829D
CyberData Corporation
6
2 Installing the Singlewire Strobe
2.1 Parts List
Table 2-2 illustrates the Singlewire Strobe parts.
Table 2-2. Parts List
Quantity
Part Name
1
Singlewire Strobe Assembly
1
Installation Quick Reference Guide
1
Singlewire Strobe Mounting
Accessory Kit
Operations Guide
Illustration
930829D
CyberData Corporation
Installing the Singlewire Strobe 7
Singlewire Strobe Setup
2.1 Singlewire Strobe Setup
2.1.1 Singlewire Strobe Connections
Figure 2-1 shows the pin connections on the J3 (terminal block). This terminal block can accept 
16 AWG gauge wire.
Note
As an alternative to using PoE power, you can supply 8 to 12 VDC at 1000 mA into the
terminal block.
Caution
GENERAL ALERT
Equipment Hazard: Contacts 1 and 2 on the J3 terminal block are only for
powering the device from a non-PoE 12 VDC power source as an alternative to
Network PoE power. Use of these contacts for any other purpose will damage the
device and void the product warranty.
Figure 2-1. Singlewire Strobe Connections
Alternate Power Input:
1 = 8 to 12 VDC at 1000 mA*
2 = Power Ground*
3
Use a 3.17 mm (1/8-inch) flat blade
Wire (IN)
screwdriver for the terminal block screws
4
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Reserved for Future Use
8 = Reserved for Future Use
1
8
*Contacts 1 and 2 on the J3 terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
Operations Guide
930829D
J3 Terminal Block
can accept 16 AWG wire
CyberData Corporation
Installing the Singlewire Strobe 8
Singlewire Strobe Setup
2.1.2 Connecting the Singlewire Strobe to the Auxiliary Relay
Warning
Electrical Hazard: The device enclosure is not rated for any AC voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached
to the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
Electrical Hazard: The relay contacts are dry and provided for a normally
open and momentarily closed configuration. Neither the alternate power input
nor PoE power can be used to drive a door strike.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
The device incorporates an on-board relay which enables users to control an external relay for
activating an auxiliary device such as an electric door strike (see Figure 2-2, "Auxiliary Relay Wiring
Diagram").
The relay contacts are limited to 1A at 30 VDC. The relay activation time is selectable through the
web interface and is controlled by DTMF tones generated from the phone being called. The DTMF
tones are selectable from the web interface as well.
Operations Guide
930829D
CyberData Corporation
CyberData Corporation
Example of External Relay (not supplied)
Controlled Device
Such As
Electric Door Strike
or
Strobe Light
Solid State
or
Mechanical
Relay
OUT
High PIV UltraFast
Switching Diode
IN
Output Contacts
AC or DC rated
Depending Upon
Controlled Device
Requirements
-
DC
POWER SUPPLY
MAX.
30 VDC @ 1A
(
)
+
8
7
6
5
4
3
2
1
930829D
AC or DC
Power Source
PCB
Auxiliary Relay Wiring Contacts
Operations Guide
Installing the Singlewire Strobe 9
Singlewire Strobe Setup
Figure 2-2. Auxiliary Relay Wiring Diagram
Installing the Singlewire Strobe 10
Singlewire Strobe Setup
2.1.3 Identifying the Singlewire Strobe Connectors and Jumpers
See the following figures and tables to identify the Singlewire Strobe connector locations and
functions.
Figure 2-3. Connector Locations for the 021084 Board
J6
J9
J7
J10
J8
J2
.
Table 2-3. Connector Functions
Operations Guide
Connector
Function
J2
Call Button Interface — Not Used
J6
Microphone Interface — Not Used
J7
Speaker Interface — Not Used
J9
Auxiliary Strobe Connector — Not Used
J8
Keypad Interface -- Not Used
J10
Proximity Sensor Interface — Not Used
930829D
CyberData Corporation
Installing the Singlewire Strobe 11
Singlewire Strobe Setup
Figure 2-4. Connector Locations for the 021084 Board
J1
J5
J12
J4
J3
.
Table 2-4. Connector Functions
Operations Guide
Connector
Function
J1
Ethernet Connector
J3
User Terminal Block Interface
J4
Reserved (Factory Use Only)
J5
Reserved (Factory Use Only)
J12
Reserved (Factory Use Only)
930829D
CyberData Corporation
Installing the Singlewire Strobe 12
Singlewire Strobe Setup
Figure 2-5. Connector Locations for the 021054 Board
J2
J1
.
Table 2-5. Connector Functions
Connector
Function
J1
Ethernet Connector
J2
Call Button Interface — Not Used
2.1.3.1 Connecting the 021054 and 021084 Boards with the 031142 Cable Assembly
Use Figure 2-6 to see how the 021054 and 021084 boards are connected with the 031142 cable
assembly.
Figure 2-6. 021054 and 021084 Boards Connected with the 031142 Cable Assembly
031142A
J9
J1
J2
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 13
Singlewire Strobe Setup
2.1.4 Link and Activity LEDs
2.1.4.1 Verifying the Network Connectivity and Data Rate
When you plug in the Ethernet cable or power supply to the device, the following occurs:
•
The square, GREEN Link LED above the Ethernet port indicates that the network connection
has been established (see Figure 2-7).
•
The square, YELLOW Activity LED blinks when there is network activity (see Figure 2-7).
Figure 2-7. Link and Activity LEDs
Activity
Operations Guide
Link
930829D
CyberData Corporation
Installing the Singlewire Strobe 14
Singlewire Strobe Setup
2.1.5 Restore the Factory Default Settings
2.1.5.1 RTFM Switch
When the Singlewire Strobe is operational and linked to the network, use the Reset Test Function
Management (RTFM) switch (Figure 2-8) to set the factory default settings.
Note
Each Singlewire Strobe is delivered with factory set default values.
Note
The Singlewire Strobe will use DHCP to obtain the new IP address (DHCP-assigned
address or default to 10.10.10.10 if a DHCP server is not present).
Figure 2-8. RTFM Switch
RTFM
To set the factory default settings:
1. Press and hold the RTFM switch for seven seconds, and then release the RTFM switch.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 15
Singlewire Strobe Setup
2.2 Configure the Singlewire Strobe Parameters
To configure the Singlewire Strobe online, use a standard web browser.
Configure each Singlewire Strobe and verify its operation before you mount it. When you are ready
to mount an Singlewire Strobe, refer to Appendix A, "Mounting the Singlewire Strobe" for instructions.
2.2.1 Factory Default Settings
All Singlewire Strobes are initially configured with the following default IP settings:
When configuring more than one Singlewire Strobe, attach the Singlewire Strobes to the network
and configure one at a time to avoid IP address conflicts.
Table 2-6. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
a
IP Address
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 16
Singlewire Strobe Setup
2.2.2 Singlewire Strobe Web Page Navigation
Table 2-7 shows the navigation buttons that you will see on every Singlewire Strobe web page.
Table 2-7. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Strobe page.
Link to the Network page.
Link to go to the SIP page.
Link to the Multicast page.
Link to the Sensor page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Autoprovisioning page.
Link to the Firmware page.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 17
Singlewire Strobe Setup
2.2.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-9 and Figure 2-10.
Figure 2-9. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-10.
Figure 2-10. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
Toggle Help button
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 18
Singlewire Strobe Setup
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-11.
), and a short description of the web
Figure 2-11. Short Description Provided by the Help Feature
Question mark
Operations Guide
930829D
A short description of the 
web page item will appear
CyberData Corporation
Installing the Singlewire Strobe 19
Singlewire Strobe Setup
2.2.4 Log in to the Configuration Home Page
1. Open your browser to the Singlewire Strobe IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Singlewire Strobe.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
http://www.cyberdata.net/support/voip/discovery.html
Note
Operations Guide
The Singlewire Strobe ships in DHCP mode. To get to the Home page, use the discovery
utility to scan for the device on the network and open your browser from there.
930829D
CyberData Corporation
Installing the Singlewire Strobe 20
Singlewire Strobe Setup
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-12):
Web Access Username: admin
Web Access Password: admin
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Figure 2-12. Home Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 21
Singlewire Strobe Setup
3. On the Home Page, review the setup details and navigation buttons described in Table 2-8.
Table 2-8. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
SIP Volume
Shows the current SIP volume level.
Multicast Volume
Shows the current Multicast volume level.
Ring Volume
Shows the current Ring volume level.
Sensor Volume
Shows the current Sensor volume level.
Volume Boost
Shows the current Volume Boost level.
Microphone Gain
Shows the current microphone gain level.
SIP Mode
Shows the current status of the SIP mode.
Multicast Mode
Shows the current status of the Multicast mode.
Event Reporting
Shows the current status of the Event Reporting mode.
Nightringer
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 22
Singlewire Strobe Setup
Table 2-8. Home Page Overview (continued)
Web Page Item
Description
Singlewire Settings
Boot Time
Shows the boot time.
Current Time
Shows the current time.
IC Servers
Shows the InformaCast server IP addresses.
Configuration File
Shows the configuration file.
B’casts Accepted
Shows the number of B’casts accepted.
B’casts Rejected
Shows the number of B’casts rejected.
B’casts Active
Shows the number of active B’casts.
Import Settings
Click Browse to select a configuration file to import.
After selecting a configuration file, click Import to import the configuration
from the selected file. Then, click Save and Reboot to store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 23
Singlewire Strobe Setup
2.2.5 Configure the Device
1. Click the Device Configuration button to open the Device Configuration page. See Figure 213.
Figure 2-13. Device Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 24
Singlewire Strobe Setup
2. On the Device Configuration page, you may enter values for the parameters indicated in
Table 2-9.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-9. Device Configuration Parameters
Web Page Item
Description
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Blink Strobe on Ring
When selected, the Strobe will blink a scene when ringing (including
when the Nightringer is ringing, if enabled). Scenes can be selected
on the Strobe Configuration Page.
Blink Strobe on MWI
When selected, the strobe will blink a scene when a voicemail is
waiting for its extension. Scenes can be selected on the Strobe
Configuration Page.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do not
recommend disabling HTTPS for security reasons.
Clock Settings
Set Time with NTP Server on boot
When selected, the time is set with an external NTP server when the
device restarts.
NTP Server
Use this field to set the address (in IPv4 dotted decimal notation or as
a canonical name) for the NTP Server. This field can accept
canonical names of up to 64 characters in length.
Posix Timezone String
See Section 2.2.5.1, "Time Zone Strings" for information about how
to use the Posix Timezone String to specify time zone and daylight
savings time where applicable. Enter up to 63 characters.
Periodically sync time with server
When selected, the time is periodically updated with the NTP server
at the configured interval below.
Time update period (in hours)
The time interval after which the device will contact the NTP server to
update the time. Enter up to 4 digits.
Current Time
Allows you to input the current time. (6 character limit)
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 25
Singlewire Strobe Setup
Table 2-9. Device Configuration Parameters (continued)
Web Page Item
Description
Relay Settings
Activate Relay During Ring
When selected, the relay will be activated for as long as the device is
ringing. When Auto-Answer Incoming Calls is enabled, the device will
not ring and this option does nothing.
Activate Relay During Night Ring
When selected, the relay will be activated as long as the Nightringer
extension is ringing.
Activate Relay While Call Active
When selected, the relay will be activated as long as the SIP call is
active.
Click on the Test Relay button to do a relay test.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.2.5.1 Time Zone Strings
The posix time zone string tells the internal date and time utilities how to handle daylight savings
time for different time zones. Table 2-10 shows some common strings.
Table 2-10. Common Time Zone Strings
Time Zone
Time Zone String
US Pacific time
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Mountain time
MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Eastern Time
EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00
Phoenix
Arizonaa
MST7
US Central Time
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
a.Phoenix, Arizona does not use daylight savings time.
Table 2-11 shows a breakdown of the parts that constitute the following time zone string:
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 26
Singlewire Strobe Setup
●
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
Table 2-11. Time Zone String Parts
Time Zone String
Examples
Time Zone String
Part
Meaning
CST6CDT
The time zone offset from GMT and three character identifiers for the time zone.
CST
Central Standard Time
6
The (hour) offset from GMT/UTC
CDT
Central Daylight Time
M3.2.0/2:00:00
The date and time when daylight savings begins.
M3
The third month (March)
.2
The 2nd occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
M11.1.0/2:00:00
The date and time when daylight savings ends.
M11
The eleventh month (November)
.1
The 1st occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
Table 2-12 has some more examples of time zone strings.
Table 2-12. Time Zone String Examples
Time Zone
Time Zone String
Tokyoa
IST-9
Berlin
b
CET-1MET,M3.5.0/1:00,M10.5.0/1:00
a.Tokyo does not use daylight savings time.
b.For Berlin, daylight savings time starts on the last Sunday in March at
01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one
hour ahead of UTC.
Time Zone Identifier A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is
needed at the beginning of the posix time zone string to properly set the time. However, the specific
letters or numbers used for the time zone identifier are not important and can be any three or four
letter or number combination that is chosen by the user. However, the time zone identifier cannot be
blank.
Figure 2-14. Three or Four Character Time Zone Identifier
You can also use the following URL when a certain time zone applies daylight savings time:
http://www.timeanddate.com/time/dst/2011.html
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 27
Singlewire Strobe Setup
World GMT Table
Table 2-13 has information about the GMT time in various time zones.
Table 2-13. World GMT Table
Operations Guide
Time Zone
City or Area Zone Crosses
GMT-12
Eniwetok
GMT-11
Samoa
GMT-10
Hawaii
GMT-9
Alaska
GMT-8
PST, Pacific US
GMT-7
MST, Mountain US
GMT-6
CST, Central US
GMT-5
EST, Eastern US
GMT-4
Atlantic, Canada
GMT-3
Brazilia, Buenos Aries
GMT-2
Mid-Atlantic
GMT-1
Cape Verdes
GMT
Greenwich Mean Time, Dublin
GMT+1
Berlin, Rome
GMT+2
Israel, Cairo
GMT+3
Moscow, Kuwait
GMT+4
Abu Dhabi, Muscat
GMT+5
Islamabad, Karachi
GMT+6
Almaty, Dhaka
GMT+7
Bangkok, Jakarta
GMT+8
Hong Kong, Beijing
GMT+9
Tokyo, Osaka
GMT+10
Sydney, Melbourne, Guam
GMT+11
Magadan, Soloman Is.
GMT+12
Fiji, Wellington, Auckland
930829D
CyberData Corporation
Installing the Singlewire Strobe 28
Singlewire Strobe Setup
2.2.6 Configure the Strobe
1. Click the Strobe Configuration button to open the Strobe Configuration page. See Figure 213.
Figure 2-15. Strobe Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 29
Singlewire Strobe Setup
2. On the Device Configuration page, you may enter values for the parameters indicated in
Table 2-9.
2.2.6.1 Scenes
You can select one of five strobe flashing behaviors (called “scenes”) and adjust the brightness for
each event that would trigger the strobe (such as SIP ring, night ring, multicast, message waiting,
sensor triggered, intrusion sensor triggered). The scenes are ADA Compliance, Fast Fade, Slow
Fade, Fast Blink, and Slow Blink.
Table 2-14. Device Configuration Parameters
Web Page Item
Description
SIP Call Scene
Use this section to select the strobe flashing behavior for the SIP Call event.
Brightness
How bright the strobe will blink on a SIP call. This is the maximum brightness for “fade” type
scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
MWI Scene
Use this section to select the strobe flashing behavior for the Message Waiting (MWI) event.
Brightness
How bright the strobe will blink when a message is waiting. This is the maximum brightness for
“fade” type scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
Nightringer Scene
Use this section to select the strobe flashing behavior for the Nightringer event.
Brightness
How bright the strobe will blink when the Nightringer is ringing. This is the maximum brightness
for “fade” type scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 30
Singlewire Strobe Setup
Table 2-14. Device Configuration Parameters (continued)
Web Page Item
Description
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
Multicast Scene
Use this section to select the strobe flashing behavior for the Multicast event.
Brightness
How bright the strobe will blink on a multicast page. This is the maximum brightness for “fade”
type scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
Sensor Scene
Use this section to select the strobe flashing behavior for the Sensor event.
Brightness
How bright the strobe will blink when the sensor is triggered. This is the maximum brightness for
“fade” type scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
Intrusion Sensor Scene
Use this section to select the strobe flashing behavior for the Intrusion Sensor event.
Brightness
How bright the strobe will blink when the intrusion sensor is triggered. This is the maximum
brightness for “fade” type scenes.
ADA Compliant
Strobe will blink on at the specified brightness for 150ms then off for 350ms during the duration of
the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 3.5 seconds during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course
of about 1.5 seconds during the duration of the event.
Slow Blink
Strobe will blink on at the specified brightness for one second then off for one second during the
duration of the event.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 31
Singlewire Strobe Setup
Table 2-14. Device Configuration Parameters (continued)
Web Page Item
Description
Fast Blink
Strobe will blink on at the specified brightness then off five times per second during the duration
of the event.
Preview Scenes
Use this section to preview the strobe flashing behavior for the Scene button that is pressed.
Brightness
How bright the strobe will blink when previewing scenes.
Click on the Fast Fade button to preview the Fast Fade strobe flashing mode.
Click on the Slow Fade button to preview the Slow Fade strobe flashing mode.
Click on the Fast Blink button to preview the Fast Blink strobe flashing mode.
Click on the Slow Blink button to preview the Slow Blink strobe flashing mode.
Click on the ADA Compliance button to preview the ADA Compliance strobe flashing mode.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web page items. First
click on the Toggle Help button, and you will see a question mark ( ) appear next to some of
the web page items. Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
930829D
CyberData Corporation
Installing the Singlewire Strobe 32
Singlewire Strobe Setup
2.2.7 Configure the Network Parameters
1. Click the Networking button to open the Network Configuration page (Figure 2-16).
Figure 2-16. Network Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 33
Singlewire Strobe Setup
2. On the Network Configuration page, enter values for the parameters indicated in Table 2-15.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-15. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking
the appropriate radio button. DHCP Addressing mode is enabled on
default and the device will attempt to resolve network addressing with
the local DHCP server upon boot. If DHCP Addressing fails, the
device will revert to the last known IP address or the factory default
address if no prior DHCP lease was established. See Section 2.2.1,
"Factory Default Settings" for factory default settings. Be sure to click
Save and Reboot to store changes when configuring a Static
address.
Hostname
This is the hostname provided by the DHCP server. See the DHCP/
DNS server documentation for more information. Enter up to 64
characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal
notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal
notation.
DHCP Timeout in seconds
Specify the desired time-out duration (in seconds) that the device will
wait for a response from the DHCP server before reverting back to
the stored static IP address. The stored static IP address may be the
last known IP address or the factory default address if no prior DHCP
lease was established. Enter up to 8 characters. A value of -1 will
retry forever.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
Operations Guide
VLAN Priority (0-7)
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of
0 may cause the VLAN ID tag to be ignored.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
930829D
CyberData Corporation
Installing the Singlewire Strobe 34
Singlewire Strobe Setup
Table 2-15. Network Configuration Parameters (continued)
Web Page Item
Description
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
930829D
CyberData Corporation
Installing the Singlewire Strobe 35
Singlewire Strobe Setup
2.2.8 Configure the SIP Parameters
1. Click SIP Config to open the SIP Configuration page (Figure 2-17).
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/support/server/index.html
Figure 2-17. SIP Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 36
Singlewire Strobe Setup
2. On the SIP Configuration page, enter values for the parameters indicated in Table 2-16.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-16. SIP Configuration Parameters
Web Page Item
Description
SIP Settings
Enable SIP Operation
When enabled, the device will transmit, receive, and process SIP messages
according to the configured SIP settings below.
Register with a SIP Server
When enabled, the device will attempt to register to the configured SIP Server(s)
on this page. To configure the device to send and receive point-to-point SIP calls,
enable SIP Operation and disable Register with a SIP Server (see Section
2.2.8.2, "Point-to-Point Configuration").
Use Cisco SRST
When enabled, the backup servers are handled according to Cisco SRST
(Survivable Remote Site Telephony). It is required for use in clustered Cisco
Unified Communications Manager topologies.
Primary SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a
fully qualified domain name. This parameter also becomes the host portion of the
SIP-URI for the device's extension on the primary SIP server. This field can accept
entries of up to 255 characters in length.
Primary SIP User ID
Specify the SIP User ID for the Primary SIP Server. This parameter becomes the
user portion of the SIP-URI for the device's extension on the primary SIP server.
Enter up to 64 alphanumeric characters.
Primary SIP Auth ID
Specify the Authenticate ID for the Primary SIP Server. This parameter is required
for SIP registration authentication. Enter up to 64 alphanumeric characters.
Primary SIP Auth Password
Specify the Authenticate Password for the Primary SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Server 1
Enter the backup SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes the host
portion of the SIP-URI for the device's extension on the backup SIP server. This
field can accept entries of up to 255 characters in length.
Backup SIP User ID 1
Specify the SIP User ID for the first backup SIP Server. This parameter becomes
the user portion of the SIP-URI for the device's extension on the first backup SIP
server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 1
Specify the Authenticate ID for the first backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 1
Specify the Authenticate Password for the first backup SIP server. This parameter
is required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Server 2
Enter a second backup SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes the host
portion of the SIP-URI for the device's extension on the second backup SIP server.
This field can accept entries of up to 255 characters in length.
Backup SIP User ID 2
Specify the SIP User ID for the second backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the second
backup SIP server. Enter up to 64 alphanumeric characters.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 37
Singlewire Strobe Setup
Table 2-16. SIP Configuration Parameters (continued)
Web Page Item
Description
Backup SIP Auth ID 2
Specify the Authenticate ID for the second backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 2
Specify the Authenticate Password for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the destination port
when sending SIP messages. The default Remote SIP Port is 5060. The supported
range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP messages.
The default Local SIP Port is 5060. The supported range is 0-65536. Enter up to 5
digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation
or a fully qualified domain name (FQDN). When an IP address is configured, the
device will send all SIP messages to this IP address. When an FQDN is
configured, the device will run DNS NAPTR, SRV, and A queries on the FQDN to
resolve an IP address to which it will send all SIP messages. This field can accept
entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when
sending SIP messages to the outbound proxy. A value of 0 will default to 5060. The
supported range is 0-65536. Enter up to 5 digits.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after establishing a SIP call. This
port number must be an even number and defaults to 10500. The supported range
is 0-65536. Enter up to 5 digits.
Nightringer Settings
Enable Nightringer
When Nightringer is enabled, the device will attempt to register a second extension
with the SIP server. Any calls made to this extension will play a ringtone
(corresponds to Night Ring on the Audiofiles page). By design, it is not possible
to answer a call to the Nightringer extension.
SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a
fully qualified domain name. This parameter also becomes the host portion of the
SIP-URI for the device's Nightringer extension on the SIP server. This field can
accept entries of up to 255 characters in length.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the destination port
when sending SIP messages for the Nightringer extension. The default Remote
SIP Port is 5060. The supported range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP messages
for the Nightringer extension. This value cannot be the same as the Local SIP Port
for the primary extension. The default Local SIP Port is 5061. The supported range
is 0-65536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation
or a fully qualified domain name (FQDN). When an IP address is configured, the
device will send all SIP messages to this IP address for the Nightringer extension.
When an FQDN is configured, the device will run DNS NAPTR, SRV, and A queries
on the FQDN to resolve an IP address to which it will send all SIP messages for the
Nightringer extension. This field can accept entries of up to 255 characters in
length.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 38
Singlewire Strobe Setup
Table 2-16. SIP Configuration Parameters (continued)
Web Page Item
Description
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when
sending SIP messages to the outbound proxy for the Nightringer extension. A
value of 0 will default to 5060. The supported range is 0-65536. Enter up to 5 digits.
User ID
Specify the SIP User ID for the SIP server. This parameter becomes the user
portion of the SIP-URI for the device's Nightringer extension. Enter up to 64
alphanumeric characters.
Authenticate ID
Specify the Authenticate ID for the SIP Server. This parameter is required for SIP
registration authentication. Enter up to 64 alphanumeric characters.
Authenticate Password
Specify the Authenticate Password for the SIP Server. This parameter is required
for SIP registration authentication. Enter up to 64 alphanumeric characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease time,
also known as the expiry. The supported range is 30-3600 seconds. Enter up to 4
digits.
Dial Out Settings
Dial Out Extension
Specify the extension the device will call when someone presses the Call button.
Enter up to 64 alphanumeric characters.
Note: For information about dial-out extension strings and DTMF tones, see
Section 2.2.8.1, "Dial Out Extension Strings and DTMF Tones (using rfc2833)".
Extension ID
A Caller identification string added to outbound calls. Enter up to 64 alphanumeric
characters.
Call Disconnection
Terminate Call After Delay
Automatically terminate an active call after a given delay in seconds. A value of 0
will disable this function. Enter up to 8 digits.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question mark
( ) appear next to some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/support/server/index.html
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 39
Singlewire Strobe Setup
2.2.8.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the SIP Configuration Page, dial out extensions support the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-17. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 64.
930829D
CyberData Corporation
Installing the Singlewire Strobe 40
Singlewire Strobe Setup
2.2.8.2 Point-to-Point Configuration
When the device is set to not register with a SIP server (see Figure 2-18), it is possible to set the
device to dial out to a single endpoint.
In this case, the dial-out extension should be the IP address of the remote device. The device can
also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point
Mode.
Note
Receiving point-to-point SiP calls may not work with all phones.
Figure 2-18. SIP Page Set to Point-to-Point Mode
Device is set to NOT register with a SiP server
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 41
Singlewire Strobe Setup
2.2.8.3 Delayed DTMF
On the SIP Configuration page the dial out extension supports the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-18. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 25.
930829D
CyberData Corporation
Installing the Singlewire Strobe 42
Singlewire Strobe Setup
2.2.9 Configure the Multicast Parameters
The Multicast Configuration page allows the device to join up to ten paging zones for receiving
ulaw/alaw encoded RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3. The device
supports simultaneous SIP and Multicast.
Note
The Singlewire Strobe does not play audio, but the Strobe LED will light up in whatever
pattern is selected in the Multicast Scene on the Strobe Configuration Page.
1. Click on the Multicast menu button to open the Multicast page. See Figure 2-19.
Figure 2-19. Multicast Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 43
Singlewire Strobe Setup
2. On the Multicast page, enter values for the parameters indicated in Table 2-19.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-19. Multicast Configuration Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Priority
Indicates the priority for the multicast group. Priority 9 is the
highest (emergency streams). 0 is the lowest (background
music). SIP calls are considered priority 4.5. See Section
2.2.9.1, "Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15
character limit).
Port
Enter the port number for this multicast group (5 character
limit [range can be from 2000 to 65535]).
Note: The multicast ports have to be even values. The
webpage will enforce this restriction.
Name
Assign a descriptive name for this multicast group (25
character limit).
Beep
When selected, the device will play a beep before multicast
audio is sent.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.2.9.1 Assigning Priority
The device will prioritize simultaneous audio streams according to their priority in the list.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams, the volume is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
930829D
CyberData Corporation
Installing the Singlewire Strobe 44
Singlewire Strobe Setup
2.2.10 Configure the Sensor Configuration Parameters
The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state.
There is an option on the Sensor page to trigger on an open or short condition on these pins. The
door sensor alarm will be activated when the Door Open Timeout parameter has been met.
The intrusion sensor is an optical sensor installed on the Singlewire Strobe board and will be
activated when the Singlewire Strobe is removed from the case.
Each sensor can trigger the following actions:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
Note
Calling a preset extension can be set up as a point-to-point call, but currently cannot send
delayed DTMF tones.
1. Click the Sensor menu button to open the Sensor page (Figure 2-20).
Figure 2-20. Sensor Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 45
Singlewire Strobe Setup
2. On the Sensor page, enter values for the parameters indicated in Table 2-20.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-20. Sensor Configuration Parameters
Web Page Item
Description
Door Sensor Settings
Door Sensor Normally Closed
Select the inactive state of the door sensor. The door sensor is
also known as the Sense Input on the device's terminal block.
Door Open Timeout (in seconds)
The time (in seconds) the device will wait before it performs an
action when the on-board door sensor is activated. The action(s)
performed are based on the configured Door Sensor Settings
below. Enter up to 5 digits.
Blink Strobe
When selected, the Strobe will blink a scene until the on-board
door sensor is deactivated. Scenes can be selected on the
Strobe Configuration Page.
Activate Relay
When selected, the device's on-board relay will be activated until
the on-board door sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the onboard door sensor is activated. Use the Dial Out Extension field
below to specify the extension the device will call.
Dial Out Extension
Specify the extension the device will call when the on-board door
sensor is activated. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls.
Enter up to 64 alphanumeric characters.
Play recorded audio
When selected, the device will call the Dial Out Extension and
play an audio file to the phone answering the SIP call
(corresponds to Door Ajar on the Audiofiles page).
Intrusion Sensor Settings
Operations Guide
Blink Strobe
When selected, the Strobe will blink a scene until the on-board
door sensor is deactivated. Scenes can be selected on the
Strobe Configuration Page.
Activate Relay
When selected, the device's on-board relay will be activated until
the intrusion sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the
intrusion sensor is activated. Use the Dial Out Extension field
below to specify the extension the device will call.
Dial Out Extension
Specify the extension the device will call when the intrusion
sensor is activated. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls.
Enter up to 64 alphanumeric characters.
Play recorded audio
When selected, the device will call the Dial Out Extension and
play an audio file (corresponds to Intrusion Sensor Triggered
on the Audiofiles page) to the phone answering the SIP call
when the intrusion sensor is activated.
930829D
CyberData Corporation
Installing the Singlewire Strobe 46
Singlewire Strobe Setup
Table 2-20. Sensor Configuration Parameters (continued)
Web Page Item
Description
Click the Test Door Sensor button to test the door sensor.
Click the Test Intrusion Sensor button to test the Intrusion
sensor.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web
page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
930829D
CyberData Corporation
Installing the Singlewire Strobe 47
Singlewire Strobe Setup
2.2.11 Configure the Audio Configuration Parameters
The Audiofiles page is used to add custom audio to the board. User uploaded audio will take
precedence over the audio files shipped with the device.
1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-21).
Figure 2-21. Audiofiles Configuration Page
2. On the Audiofiles page, enter values for the parameters indicated in Table 2-21.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-21. Audiofiles Configuration Parameters
Web Page Item
Description
Available Space
Shows the space available for the user to save custom audio files if they want to change the
message when the door or sensor is triggered.
Intrusion Sensor Triggered
Corresponds to the message “Intrusion Sensor Triggered” (24 character limit).
Door Ajar
Corresponds to the message “Door Ajar” (24 character limit).
Click on the Browse button to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the
file by using the Browse button. The Save button will delete any pre-existing user-uploaded
audio files.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 48
Singlewire Strobe Setup
2.2.11.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-22 through
Figure 2-24.
Figure 2-22. Audacity 1
Figure 2-23. Audacity 2
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 49
Singlewire Strobe Setup
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-24. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 50
Singlewire Strobe Setup
2.2.12 Configure the Event Parameters
The Events page specifies a remote server that can be used to receive HTTP POST events when
actions take place on the board.
1. Click on the Events menu button to open the Events page (Figure 2-25).
Figure 2-25. Event Configuration Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 51
Singlewire Strobe Setup
2. On the Events page, enter values for the parameters indicated in Table 2-22.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-22. Events Configuration Parameters
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote
server and port number whenever a certain action takes place.
Select an event type below to generate an HTTP POST event.
Events
Enable Relay Activated Events
When selected, the device will report relay activation.
Enable Relay Deactivated Events
When selected, the device will report relay deactivation.
Enable Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call. A Ring Event will not be generated when AutoAnswer Incoming Calls is enabled on the Device page.
Enable Night Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call to the Nightringer extension. As a reminder, the
Nightringer extension always rings upon an incoming SIP call and it
is not possible to alter this behavior.
Enable Multicast Start Events
When selected, the device will report when the device starts playing
a multicast audio stream.
Enable Multicast Stop Events
When selected, the device will report when the device stops playing
a multicast audio stream.
Enable Power On Events
When selected, the device will report when it boots.
Enable Sensor Events
When selected, the device will report when the on-board sensor is
activated.
Enable Security Events
When enabled, the device will report when the intrusion sensor is
activated.
Enable 60 Second Heartbeat Events
When enabled, the device will report a Heartbeat event every 60
seconds. SIP registration is not required to generate Heartbeat
events.
Check All
Click on Check All to select all of the events on the page.
Uncheck All
Click on Uncheck All to de-select all of the events on the page.
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 065536. Enter up to 5 digits.
Server URL
Generally, the destination URL is the name of the application that
receives the events and the string in the HTTP POST command. It
can be a script used to parse and process the HTTP POST events.
Enter up to 127 characters.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 52
Singlewire Strobe Setup
Table 2-22. Events Configuration Parameters (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question mark
to see a short description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.2.12.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 53
Singlewire Strobe Setup
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 54
Singlewire Strobe Setup
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData SIP Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 55
Singlewire Strobe Setup
2.2.13 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-26.
Figure 2-26. Autoprovisioning Page
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 56
Singlewire Strobe Setup
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 223.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-23. Autoprovisioning Configuration Parameters
Web Page Item
Description
Disable Autoprovisioning
Prevent the device from automatically trying to download a
configuration file. See Section 2.2.13.1, "Autoprovisioning"
for more information.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted
decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename.
The default autoprovisioning filename is in the format of
<mac address>.xml.
Supported filename extensions are .txt, and .xml. The
current filename is denoted by an asterisk at the bottom of
the Autoprovisioning Page. Enter up to 256 characters.
A file may have any name with an xml extension. If a file
name is entered, the device will look for the specified file
name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download
autoprovisioning files.
Autoprovisioning Autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before
checking for new autoprovisioning files. Enter up to 6 digits.
A value of 0 will disable this option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-9).
The time of day the device will check for a new
autoprovisioning file. The time must be 6 characters in length
and in HHMMSS format. An empty value will disable this
option.
Autoprovision at time (HHMMSS)
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-9).
The idle time (in minutes greater than 10) after which the
device will check for a new autoprovisioning file. Enter up to 6
digits. A value of 0 will disable this option.
Autoprovision when idle
(in minutes > 10)
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device
Configuration Page page (see Table 2-9).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 57
Singlewire Strobe Setup
Table 2-23. Autoprovisioning Configuration Parameters (continued)
Web Page Item
Description
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a
specific web page item.
Press the Download Template button to create an
autoprovisioning file for the device. See Section 2.2.13.3,
"Download Template Button"
Autoprovisioning Log
Note
The autoprovisioning log reflects the steps the device takes
with autoprovisioning, relaying information about the server,
DHCP options, configuration file names, and success or
failure of finding and parsing the files.
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.2.13.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.2.13.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-23). This file contains every configuration option that can
be set on the board.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 58
Singlewire Strobe Setup
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData VoIP Device</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
<!-<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<!-<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<!-<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 59
Singlewire Strobe Setup
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 60
Singlewire Strobe Setup
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-24. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 61
Singlewire Strobe Setup
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 62
Singlewire Strobe Setup
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 63
Singlewire Strobe Setup
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 64
Singlewire Strobe Setup
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio Configuration page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 65
Singlewire Strobe Setup
2.2.13.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 66
Singlewire Strobe Setup
2.2.13.3 Download Template Button
The Download Template button allows the user to generate, download, edit, and then store an
autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Download Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-27). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-27.
Figure 2-27. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 67
Singlewire Strobe Setup
2.3 Upgrade the Firmware and Reboot the Singlewire
Strobe
Caution
Equipment Hazard: Devices with a serial number that begins with 2441xxxxx can
only run firmware versions 10.0.0 or later.
GENERAL ALERT
To upload the firmware from your computer:
1. Retrieve the latest Singlewire Strobe firmware file from the Singlewire Strobe Downloads page
at:
http://www.cyberdata.net/products/voip/digitalanalog/strobev3singlewire/downloads.html
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the Singlewire Strobe home page as instructed in Section 2.2.4, "Log in to the
Configuration Home Page".
4. Click on the Firmware button to open the Firmware page. See Figure 2-28.
Caution
GENERAL ALERT
Equipment Hazard: CyberData strongly recommends that you first reboot the
device before attempting to upgrade the firmware of the device. See Section 2.3.1,
"Reboot the Device".
Figure 2-28. Firmware Page
5. Click on the Browse button, and then navigate to the location of the firmware file.
6. Select the firmware file.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 68
Singlewire Strobe Setup
7. Click on the Upload button.
Note
Do not reboot the device after clicking on the Upload button.
Note
This starts the upgrade process. Once the Singlewire Strobe has uploaded the file, the
Uploading Firmware countdown page appears, indicating that the firmware is being written
to flash. The Singlewire Strobe will automatically reboot when the upload is complete. When
the countdown finishes, the Firmware page will refresh. The uploaded firmware filename
should be displayed in the system configuration (indicating successful upload and reboot).
8. Table 2-25 shows the web page items on the Firmware page.
Table 2-25. Firmware Parameters
Web Page Item
Description
Current Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
firmware file that you want to upload.
Click on the Upload button to automatically upload the selected
firmware and reboot the system.
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 69
Singlewire Strobe Setup
2.3.1 Reboot the Device
To reboot a Singlewire Strobe, log in to the web page as instructed in Section 2.2.4, "Log in to the
Configuration Home Page".
1. Click on the Reboot button on the Home page (Figure 2-29). A normal restart will occur.
Figure 2-29. Reboot System Section
Reboot
Operations Guide
930829D
CyberData Corporation
Installing the Singlewire Strobe 70
Singlewire Strobe Setup
2.4 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-26 use the free unix utility, wget commands. However, any program that
can send HTTP POST commands to the device should work.
2.4.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-26. Command Interface Post Commands
Device Action
HTTP Post Commanda
Trigger relay (for configured delay)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "test_relay=yes"
Place call to extension (example: extension 130)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "call=130"
Terminate active call
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "reboot=yes"
Trigger the Door Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/sensorconfig.cgi" --post-data "doortest=yes"
Trigger the Intrusion Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/sensorconfig.cgi" --post-data "intrusiontest=yes"
a.Type and enter all of each http POST command on one line.
Operations Guide
930829D
CyberData Corporation
71
Appendix A: Mounting the Singlewire Strobe
A.1 Mount the Singlewire Strobe
Before you mount the Singlewire Strobe, make sure that you have received all the parts for each
Singlewire Strobe. Refer to Table A-1.
Table A-1. Wall Mounting Components (Part of the Accessory Kit)
Quantity
Part Name
4
#6 x 1.5 inches Sheet Metal Screw
4
#6 Ribbed Plastic Anchor
Illustration
Table A-2. Gang Box Mounting Components
Operations Guide
Quantity
Part Name
4
#6-32 x 0.625-inch
Flat-Head Machine Screw.
930829D
Illustration
CyberData Corporation
72
Mount the Singlewire Strobe
After the Singlewire Strobe is assembled, plug the Ethernet cable into the Singlewire Strobe
Assembly (see Figure A-1).
Section 2.1.4, "Link and Activity LEDs" explains how the Link and Status LEDs work.
Figure A-1. Network Connector Prior to Installation
Activity Link
Ethernet
Operations Guide
930829D
CyberData Corporation
73
Mount the Singlewire Strobe
Figure A-2 shows the wall mounting options for the Singlewire Strobe.
Note
Be sure to connect the Singlewire Strobe to the Earth Ground.
Figure A-2. Wall Mounting Options
Pre Drill Holes
(4 Places) on Wall
Backplate
Cable
Slots
Closed
Pick One of Four Mounting Hole
for Ground Wire Connection
Wall
Cutout
Cable
Entry
Slot
Network Cable &
Ground Wire
(Not Provided)
121001A
Screw
Accessory Kit
Mounting
Screw (3x)
Operations Guide
930829D
CyberData Corporation
74
Mount the Singlewire Strobe
Figure A-3 shows the gang box mounting options for the Singlewire Strobe.
Note
Be sure to connect the Singlewire Strobe to the Earth Ground.
Figure A-3. Gang Box Mounting Options
Cable
Slot
Closed
Backplate
Wall Cutout
Backplate accept
Single Gang Box
or Two Gang Box
Cable
Entry
Slot
Wall Cutout
Network Cable & Ground Wire
(Not Provided)
Mounting
Screw (3x)
121002B
Screw
Accessory Kit
Single Gang Box use two
Two Gang Box use Four
Operations Guide
Pick One of Two or Four
Available Mounting Hole
for Ground Wire Connection
930829D
CyberData Corporation
75
Mount the Singlewire Strobe
Figure A-4 shows the maximum recommended wall cutout dimensions for mounting the Singlewire
Strobe.
Figure A-4. Maximum Recommended Wall Cutout Dimensions
0.25 [6.4]
0.25 [6.4]
Wall Cutout
0.25 [6.4]
0.25 [6.4]
Dimensions are in Inches [Millimeter]
Operations Guide
930829D
CyberData Corporation
76
Appendix B: Troubleshooting/Technical
Support
B.1 Frequently Asked Questions (FAQ)
A list of frequently asked questions (FAQs) are available on the Singlewire Strobe product page at:
http://www.cyberdata.net/products/voip/digitalanalog/strobev3singlewire/faqs.html
Select the support page for your product to see a list of frequently asked questions for the
CyberData product:
B.2 Documentation
The documentation for this product is released in an English language version only. 
You can download PDF copies of CyberData product documentation from the
Singlewire Strobe product page at:
http://www.cyberdata.net/products/voip/digitalanalog/strobev3singlewire/docs.html
Operations Guide
930829D
CyberData Corporation
77
Contact Information
B.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601 Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical Support
form at the following website:
http://www.cyberdata.net/support/contactsupportvoip.php
Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Returned
Materials
Authorization
To return the product, contact the Returned Materials Authorization (RMA) department:
Phone: 831-373-2601, Extension 136
Email: RMA@CyberData.net
When returning a product to CyberData, an approved CyberData RMA number must be printed on
the outside of the original shipping package. No product will be accepted for return without an
approved RMA number. Send the product, in its original package, to the following address:
CyberData Corporation
3 Justin Court 
Monterey, CA 93940 
Attention: RMA "your RMA number"
RMA Status Form If you need to inquire about the repair status of your product(s), please use the CyberData RMA
Status form at the following web address:
http://www.cyberdata.net/support/rmastatus.html
Operations Guide
930829D
CyberData Corporation
78
Warranty
B.4 Warranty
CyberData warrants its product against defects in material or workmanship for a period of two
years from the date of purchase. Should the product fail Within Warranty, CyberData will repair
or replace the product free of charge. This warranty includes all parts and labor.
Should the product fail Out of the Warranty period, a flat rate repair charge of one half of the
purchase price of the product will be assessed. Repairs that are Within Warranty period but are
damaged by improper installation, modification, or abuse are deemed Out of Warranty and will
be charged at the Out of Warranty rate. A device is deemed Out of Warranty when its purchase
date is longer than two years or when the device has been damaged due to human error during
installation, modification, or abuse. A replacement unit will be offered at full cost if the device
cannot be repaired.
End of Life Devices are included under this policy. End of Life devices are devices that are no
longer produced or sold. Technical support is still available for these devices. However, no
firmware revisions or updates will be provided. If an End of Life device cannot be repaired, the
replacement offered may be the current version of the device.
Products shipped to CyberData, both within and out of warranty, are shipped at the expense of
the customer. CyberData will pay return shipping charges for repaired products.
CyberData shall not under any circumstances be liable to any person for any special, incidental,
indirect or consequential damages, including without limitation, damages resulting from use or
malfunction of the products, loss of profits or revenues or costs of replacement goods, even if
CyberData is informed in advance of the possibility of such damages.
B.4.1 Warranty & RMA Returns within the United States
If service is required, you must contact CyberData Technical Support prior to returning any products
to CyberData. Our Technical Support staff will determine if your product should be returned to us for
further inspection. If Technical Support determines that your product needs to be returned to
CyberData, an RMA number will be issued to you at this point.
Your issued RMA number must be printed on the outside of the shipping box. No product will be
accepted for return without an approved RMA number. The product in its original package should be
sent to the following address:
CyberData Corporation
3 Justin Court.
Monterey, CA 93940
Attn: RMA "xxxxxx"
B.4.2 Warranty & RMA Returns Outside of the United States
If you purchased your equipment through an authorized international distributor or reseller, please
contact them directly for product repairs.
Operations Guide
930829D
CyberData Corporation
79
Warranty
B.4.3 Spare in the Air Policy
CyberData now offers a Spare in the Air no wait policy for warranty returns within the United States
and Canada. More information about the Spare in the Air policy is available at the following web
address:
http://www.cyberdata.net/support/warranty/spareintheair.html
B.4.4 Return and Restocking Policy
For our authorized distributors and resellers, please refer to your CyberData Service Agreement for
information on our return guidelines and procedures.
For End Users, please contact the company that you purchased your equipment from for their return
policy.
B.4.5 Warranty and RMA Returns Page
The most recent warranty and RMA information is available at the CyberData Warranty and RMA
Returns Page at the following web address:
http://www.cyberdata.net/support/warranty/index.html
Operations Guide
930829D
CyberData Corporation
80
Index
audio 47
default IP settings 15
door sensor 44
intrusion sensor 44
network 32
SIP 35
using Web interface 15
configuration home page 20
configuration page
configurable parameters 21, 24, 29, 33
contact information 77
contact information for CyberData 77
Current Network Settings 33
current network settings 33
CyberData contact information 77
Numerics
16 AWG gauge wire 7
A
AC voltages 2
AC voltages, enclosure is not rated 8
activate relay (door sensor) 45
activate relay (intrusion sensor) 45
activity LED 13
address, configuration login 19
audio configuration 47
audio configuration page 47
audio encodings 3
audio files, user-created 48
Autoprovision at time (HHMMSS) 56
autoprovision at time (HHMMSS) 56
autoprovision when idle (in minutes > 10) 56
autoprovisioning 57
download template button 57
autoprovisioning autoupdate (in minutes) 56
autoprovisioning configuration 55, 56
autoprovisioning filename 56
autoprovisioning server (IP Address) 56
auxiliary relay 8
auxiliary relay wiring diagram 9
D
default
device settings 80
gateway 15
IP address 15
subnet mask 15
username and password 15
web login username and password 20
default device settings 14
default gateway 15, 33
default IP settings 15
default login address 19
device configuration 23
device configuration parameters 56
the device configuration page 55
device configuration page 23, 28
device configuration parameters 24, 29
device configuration password
changing for web configuration access 23
DHCP Client 3
dial out extension (door sensor) 45
dial out extension (intrusion sensor) 45
dial out extension strings 39
dial-out extension strings 41
dimensions 4, 5
discovery utility program 19
DNS server 33
door sensor 44, 45
activate relay 45
dial out extension 45
door open timeout 45
door sensor normally closed 45
flash button LED 45
B
backup SIP server 1 36
backup SIP server 2 36
backup SIP servers, SIP server
backups 36
baud rate
verifying 13
C
changing
the web access password 23
Cisco SRST 36
command interface 70
commands 70
configurable parameters 21, 24, 29, 33
configuration
Operations Guide
930829D
CyberData Corporation
81
download autoprovisioning template button 57
DTMF tones 39, 41
DTMF tones (using rfc2833) 39
IP addressing
default
IP addressing setting 15
E
J
earth ground 73, 74
enable night ring events 51
ethernet cable 72
event configuration
enable night ring events 51
expiration time for SIP server lease 38
export settings 22
J3 terminal block, 16 AWG gauge wire 7
L
lease, SIP server expiration time 38
LED
green link LED 13
yellow activity LED 13
lengthy pages 43
link LED 13, 72
local SIP port 37
log in address 19
F
factory default settings 14
how to set 14
firmware
where to get the latest firmware 67
flash button LED (door sensor) 45
M
MGROUP
MGROUP Name 43
mounting the device 71
Multicast IP Address 43
G
gang box mounting 73, 74
get autoprovisioning template 57
GMT table 27
GMT time 27
N
navigation (web page) 16
navigation table 16
network configuration 32
Network Setup 32
nightring tones 43
Nightringer 7, 66, 67
nightringer settings 37
NTP server 24
H
home page 20
http POST command 70
http web-based configuration 3
I
P
identifier names (PST, EDT, IST, MUT) 26
identifying your product 1
illustration of device mounting process 71
import settings 22
import/export settings 22
installation, typical device system 2
intrusion sensor 44, 45
activate relay 45
dial out extension 45
IP address 15, 33
Operations Guide
packet time 3
pages (lengthy) 43
part number 4
parts list 6
password
for SIP server login 36
login 20
restoring the default 15
930829D
CyberData Corporation
82
point-to-point configuration 40
port
local SIP 37
remote SIP 37
posix timezone string
timezone string 24
POST command 70
power requirement 4
priority
assigning 43
product
configuring 15
mounting 71
parts list 6
product features 3
product overview
product features 3
product specifications 4
supported protocols 3
typical system installation 2
product specifications 4
protocols supported 3
local SIP port 37
user ID 36
SIP configuration 35
SIP Server 36
SIP configuration parameters
outbound proxy 37, 38
registration and expiration, SIP server lease 38
user ID, SIP 36
SIP registration 36
SIP remote SIP port 37
SIP server 36
password for login 36
user ID for login 36
Spare in the Air Policy 79
SRST 36
status LED 72
subnet mask 15, 33
supported protocols 3
T
tech support 77
technical support, contact information 77
terminal block, 16 AWG gauge wire 7
time zone string examples 26
R
reboot 68, 69
remote SIP port 37
Reset Test Function Management (RTFM) switch 14
resetting the IP address to the default 71, 76
restoring factory default settings 14, 80
restoring the factory default settings 14
return and restocking policy 79
ringtones 43
lengthy pages 43
RMA returned materials authorization 77
RMA status 77
RTFM switch 14
RTP/AVP 3
U
user ID
for SIP server login 36
username
changing for web configuration access 23
default for web configuration access 20
restoring the default 15
V
S
verifying
baud rate 13
network connectivity 13
VLAN ID 33
VLAN Priority 33
VLAN tagging support 33
VLAN tags 33
sales 77
sensor setup page 44
sensor setup parameters 44
sensors 45
server address, SIP 36
service 77
set time with external NTP server on boot 24
setting up the device 7
settings, default 14
SIP
enable SIP operation 36
Operations Guide
W
warranty 78
warranty & RMA returns outside of the United States 78
930829D
CyberData Corporation
83
warranty & RMA returns within the United States 78
warranty and RMA returns page 79
warranty policy at CyberData 78
web access password 15
web access username 15
web configuration log in address 19
web page
navigation 16
web page navigation 16
web-based configuration 15
weight 4
wget, free unix utility 70
Operations Guide
930829D
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising