CyberData | 011182 | Quick Start Guide | Cyberdata 011182/011183 Singlewire InformaCast® Talk Back Speaker (Replacement Product Below) Quick Start Guide

Cyberdata 011182/011183 Singlewire InformaCast® Talk Back Speaker (Replacement Product Below) Quick Start Guide
V2 Speaker, Push-to-Talk, Singlewire
Quick Start Guide
The IP Endpoint Company
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide, which is available on the
Documentation page at the following website address:
http://www.cyberdata.net/products/voip/digitalanalog/singlewirespeakerptt/docs.html
2.0 Select Power Source
PoE Switch
PoE Injector
Set PoE power type to IEEE 802.3af
Power Class 0 (15.4W)a
CAT6 cable recommended—for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
a. When initiating the device for the first time, we recommend manually adjusting the PoE switch port power
setting to Class 3 to ensure sufficient power allocation. Once the initial setup has been completed and the
device is SIP enabled, the Administrator may prefer a final power setting adjustment to Class 0.
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of the device. See the
following figure:
Network
Link/Activity
(Yellow LED)
Speaker
Status
(Green LED)
3.2. The GREEN power/status LED and the YELLOW network LED come on immediately. The YELLOW
network LED will blink to indicate network traffic. After about 27 seconds, the GREEN power/status
LED will blink twice to indicate that the board is fully booted.
This concludes the power test.
Quick Start Guide
930465B
4.0 InformaCast Configuration File Retrieval
4.1. DHCP should be enabled. After the speaker initializes, it will send a broadcast to the DHCP server
to ask for the location of its InformaCastSpeaker.cfg configuration file.
4.2. SLP or TFTP?
•
SLP should be enabled on InformaCast version 5.0.4 or higher. SLP is an InformaCast protocol
introduced in InformaCast version 5.0.4. The speaker will retrieve its configuration file from an
InformaCast server folder specified by SLP. SLP method is preferred.
•
TFTP servers may be used instead of SLP. In this alternate scenario, DHCP option 150 is required to
provide the speaker with the address of the TFTP server. Otherwise, the speaker will be unable to
retrieve its configuration file.
Note The CyberData V2 Ceiling Speaker and InformaCast server should be on the same subnet
during the speaker's initial configuration if it cannot access the VLANs upon which the
InformaCast Server and DHCP servers are located.
5.0 Singlewire-Enabled V2 Ceiling Speaker Identification and Testing
5.1. Ensure the InformaCast Server has detected a new speaker.
5.2. Test the newly detected speaker.
5.3. Add the newly detected speaker to the InformaCast Server.
6.0 Contacting CyberData VoIP Technical Support
We encourage you to access our Technical Support help desk at the following address:
http://support.cyberdata.net/
Note
You can also access the Technical Support help desk by navigating through menus on the CyberData
website (www.CyberData.net) as shown in the following figure:
The Technical Support help desk provides the options of accessing documentation for your CyberData
product, browsing the knowledge base, and submitting a troubleshooting ticket.
Please be advised requests for Returned Materials Authorization (RMA) numbers require an active VoIP
Technical Support ticket number. A product will not be accepted for return without an approved RMA
number.
Quick Start Guide
930465B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising