CyberData | 011097 | Datasheet | Cyberdata 011097 SIP Loudspeaker Amplifier-PoE (Replacement Product Below) Datasheet

Cyberdata 011097 SIP Loudspeaker Amplifier-PoE (Replacement Product Below) Datasheet
Now with up to 25 watts output (802.3at)
VoIP V2 Loudspeaker Amplifier
The IP Endpoint Company
The new CyberData V2 SIP-enabled VoIP Loudspeaker
Amplifier provides an easy method for implementing an IP-based
overhead paging system for both new and legacy installations.
With up to 25 watts of driving power (802.3at), the Amplifier
provides direct drive of a standard Horn speaker and supports
a line-out connector for connection to an external amplifier.
The interface is compatible with most SIP-based IP PBX
servers that comply with the SIP RFC 3261. For non-SIP
environments, the Loudspeaker Amplifier can be configured to
Loudspeaker (part #011068) must be purchased separately.
listen to multicast address and port number combinations to
Specifications
form paging zones.
Ethernet I/F
10/100 Mbps
Ringer Mode
Power Input
PoE 802.3at or 802.3af
The VoIP V2 Loudspeaker Amplifier supports two SIP
Operating Temperature
-10o C to 50o C (14o F to 122o F)
extensions. One extension can be assigned to a page group for
Protocol
SIP RFC 3261
Payload Types
G711
Warranty
2 Years Limited
Dimensions
14" x 10" x 4"
Output

802.3af - up to 8 watts

802.3at - up to 25 watts
auto answer paging. The second extension can be assigned to
a “First-to-Answer” ring group with IP phones. An audio ring file
is activated when the second SIP extension of the ceiling
speaker is dialed. If any of the IP phones in the ring group is
answered (or if the caller hangs up), the Loudspeaker Amplifier
stops ringing.
Line In:
Features
Input Signal Amplitudes
Input Impedance
 SIP and Simultaneous Multicast
2.0 VPP maximum
10k Ohm
 Dual-speed ethernet 10/100 Mbps
Line Out:
 Web-based configuration
Output Signal Amplitudes
Output Level
Total Harmonic Distortion
Output Impedance
2.0 VPP maximum
+2dBm nominal
0.5% maximum
10k Ohm
Boxed Weight
6.5 lbs.
 PoE 802.3at and 802.3af-enabled
 Line-in for background music
 Line-out connector
 DTMF controlled relay
 Direct 8 Ohm speaker drive
 User-uploadable tones and messages
Part Number
Loudspeaker Amplifier, AC
011095
Loudspeaker Amplifier, PoE
Loudspeaker Part Number
011097
011068
 Digital and manual volume control
 Second SIP endpoint "Night Ringer"
 Autoprovisioning
 Auto-call voice message from input port sense
The IP Endpoint Company
CyberData Corporation

3 Justin Court, Monterey, CA 93940

831.373.2601

Fax: 831.373.4193

www.cyberdata.net
VoIP V2 LoudspeakerAmplifier
Typical Installation - AC Version (Part# 011095)
Generic Ethernet Switch
1
2
3
4
5
6
011095
VoIP V2 Loudspeaker Amplifiers – AC Required
High Power PoE Injector in Box
IP Phone
IP-PBX Server
Typical Installation - PoE 802.3af (Part# 011097)
802.3af Generic PoE Switch or
802.3at High Power Switch
1
2
3
4
5
6
011097
VoIP V2 Loudspeaker Amplifiers – No AC Required
CyberData Corporation

3 Justin Court, Monterey, CA 93940

831.373.2601

IP Phone
Fax: 831.373.4193

IP-PBX Server
www.cyberdata.net
930340I/130422
VoIP V2 Loudspeaker Amplifier
Configuring the V2 Loudspeaker Amplifier for Alarm Sensing
User can upload an audio message
to the Loudspeaker Amplifier.
When the “Sense-In” is activated, the stored
Audio file will play out the local speaker and
repeat until the condition is cleared.
The Loudspeaker Amplifier can also call a
pre-set phone number and when that phone
answers, the stored Audio message will
also be played to the phone.
IP Phone
Window Reed switch is connected
to the “Sense-In” connection.
Window Reed Switch
V2 Loudspeaker Amplifier with Strobe Alert
Alert Strobe
Solid State
or
Mechanical
Relay
OUT
When the V2 Loudspeaker
Amplifier is called from a remote
phone, the relay on the paging
amplifier can be programmed to
blink and drive an Alert Strobe.
High PIV UltraFast
Switching Diode
IN
Output Contacts
AC or DC rated
Depending Upon
Controlled Device
Requirements
-
AC or DC
Power Source
DC
POWER SUPPLY
MAX.
30 VDC @ 1A
(
)
+
Loudspeaker Amplifier
V2 Loudspeaker Amplifier Connections
1-Sense (+)
2-GND
3-Relay COM
4-Relay NO
5-Line-In(+)
6-Line-In(-)
7-Line-Out(+)
8-Line-Out(-)
9-Spkr Out(+)
10-Spkr Out (-)
CLASS II WIRING
CyberData Corporation

3 Justin Court, Monterey, CA 93940

831.373.2601

Fax: 831.373.4193

www.cyberdata.net
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising