CyberData | 011087 | Quick Start Guide | Cyberdata 011087 SIP Strobe (Replacement Product Below) Quick Start Guide

Cyberdata 011087 SIP Strobe (Replacement Product Below) Quick Start Guide
The IP Endpoint Company
SIP Strobe
Quick Start Guide
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide,
which is available on the Documentation page at the following website
address:
http://www.cyberdata.net/products/voip/digitalanalog/strobe/docs.html
Note
You can also navigate to the Documentation page by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
1
2
3
2.0 Select Power Source
PoE Switch
PoE Injector
Set PoE power type to Class 0 = 13W
CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100Mbps
Quick Start Guide
930448D
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity above the
ethernet port on the back of the SIP Strobe. See the following figure:
3.2. The GREEN Link LED blinks off once during the boot up process and then
comes on again and remains constant (solid GREEN). The YELLOW
Activity LED may be blinking depending on the network activity.
Normally, this process will take about 30 seconds. However, if no DHCP is
available, then this process could take up to 2 minutes.
This concludes the power test. Go to Section 4.0, "Connecting to a Network
in a Test Environment".
Quick Start Guide
930448D
4.0 Connecting to a Network in a Test Environment
Note
The following connections are usually needed for this procedure:
•
Computer
•
PoE switch or injector
•
CyberData device
3.1. In a test environment, use a computer that is connected to the same switch
as a single CyberData device. Note the subnet of the test computer.
3.2. Use the CyberData Discovery Utility program to locate the device on the
network. You can download the Discovery Utility program from the following
website address:
http://www.cyberdata.net/support/voip/discovery.html
3.3. Wait for initialization to complete before using the Discovery Utility program
to scan for a device. The device will show the current IP address, MAC
address, and serial number.
3.4. Select the device.
3.5. Click Launch Browser. If the IP address is in a reachable subnet from the
computer that you are using to access the device, the Discovery Utility
program should be able to launch a browser window pointing to the device’s
IP address.
3.6. Log on to the web interface by using the default username (admin) and
password (admin) to configure the device.
3.7. The device is now ready to be set for your desired network configuration.
You may search the Compatible IP-PBX Servers index for available sample
VoIP phone system configurations and set up guides at the following website
address:
http://www.cyberdata.net/support/server/index.html
Quick Start Guide
930448D
5.0 Contacting CyberData VoIP Technical Support
Please visit our website and complete the Contact VoIP Tech Support form
available at the following website address:
http://www.cyberdata.net/support/contactsupportvoip.php
Note
You can also navigate through menus to the Support form by going to
www.CyberData.net as shown in the following figure:
The Contact VoIP Tech Support form initiates a ticket which CyberData uses for
tracking. Most importantly, the Contact VoIP Tech Support form tells us which
PBX system and software version that you are using, the make and model of the
switch, and other essential troubleshooting information. Please also include as
much detail as possible in the Describe Problem section of the Support form.
Requests for Returned Materials Authorization (RMA) numbers require an active
VoIP Technical Support ticket number. A product will not be accepted for return
without an approved RMA number.
More information about warranty and RMA returns is available at the following
website address:
http://www.cyberdata.net/support/warranty/index.html
Quick Start Guide
930448D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising