CyberData | 010935 | Operations Guide | Cyberdata 010935 SIP-enabled IP Outdoor Intercom (Replacement Product Below) Operations Guide

Cyberdata 010935 SIP-enabled IP Outdoor Intercom (Replacement Product Below) Operations Guide
The IP Endpoint Company
VoIP Intercom
Operations Guide
Part #010935
Document Part #930242A-D
for Firmware Version 6.5.1
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
PoE VoIP Intercom Operations Guide 930242A-D
Part # 010935
COPYRIGHT NOTICE:
© 2013, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://www.cyberdata.net/support/contactsupportvoip.html

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
CyberData Corporation
930242A-D
Operations Guide
Revision Information
Revision 930242A-D, which was released on October 3, 2014 and corresponds to firmware version
6.5.1, has the following changes:
•
Updates Figure 2-1, "VoIP Intercom Connections".
Browsers Supported
The following browsers have been tested against firmware version 6.5.1:
Operations Guide
•
Internet Explorer (version: 10)
•
Firefox (also called Mozilla Firefox) (version: 23.0.1)
•
Chrome (version: 29.0.154.66 m)
•
Safari (version: 5.1.7)
930242A-D
CyberData Corporation
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The VoIP Intercom enclosure is not rated for any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
CyberData Corporation
930242A-D
Operations Guide
Pictorial Alert Icons
GENERAL ALERT
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
CyberData Corporation
930242A-D
Operations Guide
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................4
1.4 Supported Protocols .................................................................................................................5
1.5 Supported SIP Servers .............................................................................................................5
1.6 Product Specifications ..............................................................................................................6
1.7 Dimensions ...............................................................................................................................7
Chapter 2 Installing the VoIP Intercom
9
2.1 Parts List ..................................................................................................................................9
2.1 Intercom Setup .......................................................................................................................10
2.1.1 VoIP Intercom Connections ..........................................................................................10
2.1.2 Connecting the Intercom to the Auxiliary Relay ...........................................................11
2.1.3 Identifying the VoIP Intercom Connectors ....................................................................13
2.1.4 Call Button and the Call Button LED ............................................................................15
2.1.5 Network Connectivity, and Data Rate ..........................................................................16
2.1.6 RTFM Button ................................................................................................................18
2.1.7 Announcing the IP Address ..........................................................................................20
2.1.8 Restore the Factory Default Settings ...........................................................................21
2.1.9 Adjust the Volume ........................................................................................................25
2.2 Configure the Intercom Parameters ......................................................................................25
2.2.1 Intercom Web Page Navigation ....................................................................................26
2.2.2 Log in to the Configuration Home Page .......................................................................27
2.2.3 Configure the Device ....................................................................................................30
2.2.4 Configure the Network Parameters .............................................................................33
2.2.5 Configure the SIP Parameters .....................................................................................35
2.2.6 Configure the Nightringer Parameters ..........................................................................40
2.2.7 Configure the Sensor Configuration Parameters ..........................................................42
2.2.8 Configure the Multicast Parameters .............................................................................45
2.2.9 Configure the Audio Configuration Parameters ............................................................47
2.2.10 Configure the Event Parameters ................................................................................52
2.2.11 Configure the Autoprovisioning Parameters ...............................................................57
2.3 Upgrade the Firmware and Reboot the Intercom ...................................................................65
2.3.1 Reboot the Intercom .....................................................................................................67
2.4 Command Interface ................................................................................................................68
2.4.1 Command Interface Post Commands ..........................................................................68
Appendix A Mounting the Intercom
74
A.1 Mount the Intercom ...............................................................................................................74
A.1.1 Custom Flush Mounting ...............................................................................................79
Appendix B Setting up a TFTP Server
80
B.1 Set up a TFTP Server ............................................................................................................80
B.1.1 In a LINUX Environment ..............................................................................................80
B.1.2 In a Windows Environment .........................................................................................80
Appendix C Troubleshooting/Technical Support
81
C.1 Frequently Asked Questions (FAQ) ........................................................................................81
C.2 Documentation .......................................................................................................................81
C.3 Contact Information ................................................................................................................82
C.4 Warranty .................................................................................................................................83
C.4.1 Warranty & RMA Returns within the United States ......................................................83
C.4.2 Warranty & RMA Returns outside of the United States ...............................................83
C.4.3 Spare in the Air Policy ..................................................................................................84
C.4.4 Return and Restocking Policy ......................................................................................84
C.4.5 Warranty and RMA Returns Page ...............................................................................84
Index
Operations Guide
85
930242A-D
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the VoIP Intercom, look for a model number label similar to the one shown in Figure 1-1.
The model number on the label should be 010935.
Figure 1-1. Model Number Label
WWW.CYBERDATA.NET
VoIP INTERCOM, PoE
WITH INTRUSION DETECTION
010935 / 021043D
035000001
Model number
Operations Guide
930242A-D
CyberData Corporation
Product Overview 2
How to Identify This Product
1.2 Typical System Installation
The Voice-over-IP (VoIP) Intercom is a SIP endpoint designed to provide VoIP phone connectivity in
a tamper proof and secure package.
Figure 1-2, Figure 1-3, and Figure 1-4 illustrate how the VoIP Intercoms can be installed as part of a
VoIP phone system.
Figure 1-2. Typical Installation—Door Entry/Access Control
802.3af Compliant Ethernet Hub
1
Door Strike
VoIP Intercom
2
3
4
5
6
IP Phone
VoIP Intercom
IP PBX Server
Figure 1-3. Typical Installation—Mass Notification
Generic PoE Hub
1
Speaker
Loudspeaker
Amplifier
2
3
4
5
6
Strobe
Light
IP Phone
IP PBX Server
Figure 1-4. Typical Installation—Emergency Phone
Generic PoE Hub
1
VoIP Intercom
Operations Guide
IP Phone
2
3
4
IP Phone
930242A-D
5
6
IP Phone
IP PBX Server
CyberData Corporation
Product Overview 3
How to Identify This Product
Warning
Electrical Hazard: The VoIP Intercom enclosure is not rated for any AC voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Operations Guide
930242A-D
CyberData Corporation
Product Overview 4
How to Identify This Product
1.3 Product Features
Operations Guide
930242A-D
●
SIP
●
Dual speeds of 10 Mbps and 100 Mbps
●
802.3af compliant
●
2 gang outlet box size
●
Adaptive full duplex voice operation
●
Network/Web management
●
Network adjustable speaker volume
adjustment
●
Network configurable door or intrusion
sensor settings
●
Network configurable relay activation
settings
●
Dial Out Extension supports the addition of
comma delimited pauses before sending
additional DTMF tones
●
Network configurable microphone input
sensitivity adjustment
●
Network downloadable product firmware
●
Doubles as a paging speaker
●
Call button
●
Call activity indicator (light)
●
Tamper proof design
●
One dry contact relay for auxiliary control
●
Autoprovisioning
●
Configurable audio files
●
Night Ringer
●
Three year warranty
●
Peer-to-peer capable
●
Door closure and tamper alert signal
●
Optional Torx screws with driver kit
CyberData Corporation
Product Overview 5
How to Identify This Product
1.4 Supported Protocols
The Intercom supports:
●
SIP
●
HTTP Web-based configuration
Provides an intuitive user interface for easy system configuration and verification of Intercom
operations.
●
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
●
TFTP Client
Facilitates hosting for the Autoprovisioning configuration file.
●
RTP
●
RTP/AVP - Audio Video Profile
●
Facilitates autoprovisioning configuration values on boot
●
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
Packet Time 20 ms
1.5 Supported SIP Servers
Go to the following link to find the VoIP Intercom product page which will have information on how to
configure the VoIP Intercom for various supported SIP servers:
http://www.cyberdata.net/support/server/index.html
Operations Guide
930242A-D
CyberData Corporation
Product Overview 6
How to Identify This Product
1.6 Product Specifications
Category
Specification
Speaker Output
1 Watt Peak Power
Ethernet I/F
10/100 Mbps
Protocol
SIP RFC 3261 Compatible
Power Input
PoE 802.3af compliant
or +5 volts at 1000m
Operating Temperature
-10o C to 50o C (14o F to 122o F)
Payload Types
G711, A-law and µ-law
Part Number
010935
Dimensions
5” x 5” x 2.5”
Weight
1.6 lbs./shipping weight of 2.2 lbs.
(0.7 kg/shipping weight of 1.0kg)
Auxiliary Relay
Operations Guide
1A at 30 VDC
930242A-D
CyberData Corporation
Product Overview 7
How to Identify This Product
1.7 Dimensions
5.00 [127.0]
4.70 [119.3]
5.00 [127.0]
Figure 1-5. Dimensions—Size of Unit With Case
2.36 [60.0]
Operations Guide
4.64 [117.8]
WALL CUTOUT
DIMENSIONS ARE IN INCHES [MILLIMETER]
930242A-D
CyberData Corporation
Product Overview 8
How to Identify This Product
5.000 [127.0]
Figure 1-6. Dimensions—Size of Unit Without Gang Box
5.000 [127.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
1.985 [50.4]
4.200 [106.7]
4.200 [106.7]
Operations Guide
930242A-D
CyberData Corporation
9
2 Installing the VoIP Intercom
2.1 Parts List
Table 2-1 illustrates the SiP VoIP and PoE Speaker parts.
Table 2-1. Parts List
Operations Guide
Quantity
Part Name
1
Intercom Assembly
1
Installation Quick Reference Guide
1
Intercom Mounting Accessory Kit
930242A-D
Illustration
CyberData Corporation
Installing the VoIP Intercom 10
Intercom Setup
2.1 Intercom Setup
2.1.1 VoIP Intercom Connections
Figure 2-1 shows the pin connections on the J7 (terminal block). This terminal block can accept 
16 AWG gauge wire.
Note
As an alternative to using PoE power, you can supply 5 VDC at 1000 mA into the terminal
block.
Caution
GENERAL ALERT
Equipment Hazard: Contacts 1 and 2 on the J3 terminal block are only for
powering the Intercom from a non-PoE +12VDC power source as an alternative to
Network PoE power. Use of these contacts for any other purpose will damage the
Intercom and void the product warranty.
Figure 2-1. VoIP Intercom Connections
Wire
in, 16 AWG
Accepts
accept
gaugewire
wirerange
up to 16 AWG
6
5
4
3
2
1
Alternate Power Input:Alternate Power Input:
1 = +8 to +12VDC at 1000 mA
2 = Power Ground* 1 = +5V at 1000 mA
2 = Power Ground
Relay Contact:
(1A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
J3
Terminal Block
3
4
Relay Contact:
3
4
(2A at 30 VDC or 0.4A at 125 VAC
5 = Door Sense Input
forReference
continuous loads)
6 = Door Sense Ground
3 = Normally Open Common
= Normally
Open
*Contacts 1 and 2 on4the
J3 terminal
blockContact
are only for
powering the Intercom
a non-PoE
+12VDC power
5 =from
Door
Sense Input
source as an alternative
to Network
power.
Use of
6 = Door
SensePoE
Ground
Reference
these contacts for any other purpose will damage the
Intercom and void the product warranty.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 11
Intercom Setup
2.1.2 Connecting the Intercom to the Auxiliary Relay
Warning
Electrical Hazard: The VoIP Intercom enclosure is not rated for any AC
voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached
to the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
Electrical Hazard: The relay contacts are dry and provided for a normally
open and momentarily closed configuration. Neither the alternate power input
nor PoE power can be used to drive a door strike.
GENERAL ALERT
The VoIP Intercom incorporates an on-board relay which enables users to control an external relay
for activating an auxiliary device such as an electric door strike (see Figure 2.1.2, "Connecting the
Intercom to the Auxiliary Relay").
The Intercom relay contacts are limited to 1A at 30 VDC. The Intercom relay activation time is
selectable through the web interface and is controlled by DTMF tones generated from the phone
being called. The DTMF tones are selectable from the web interface as well.
Note
Operations Guide
The three digit code for the auxiliary relay must be sent in conformance with RFC2833
DTMF generation.
930242A-D
CyberData Corporation
Controlled Device
Such As
Electric Door Strike
or
Strobe Light
Solid State
or
Mechanical
Relay
OUT
High PIV UltraFast
Switching Diode
Intercom PCB
IN
CyberData Corporation
Example of External Relay (not supplied)
Output Contacts
AC or DC rated
Depending Upon
Controlled Device
Requirements
VoIP Intercom
-
DC
POWER SUPPLY
MAX.
30 VDC @ 1A
(
)
+
6
5
4
3
2
1
930242A-D
AC or DC
Power Source
Auxiliary Relay Wiring Contacts
Operations Guide
Installing the VoIP Intercom 12
Intercom Setup
Figure 2-2. Auxiliary Relay Wiring Diagram
Installing the VoIP Intercom 13
Intercom Setup
2.1.3 Identifying the VoIP Intercom Connectors
See the following Figures and Tables to identify the connectors and functions.
Figure 2-3. J2, J5, and J6 Connector Locations
.
Table 2-2. Connector Functions
Connector
Operations Guide
Function
J2
Call Button. LED Interface
J5
Microphone Interface
J6
Speaker Interface
930242A-D
CyberData Corporation
Installing the VoIP Intercom 14
Intercom Setup
Figure 2-4. Connector Locations
Table 2-3. Connector Functions
Connector
Operations Guide
Function
J1
PoE Network Connection (RJ-45 ethernet)
J3
Terminal Block (see Figure 2-1)
J4
Factory Only
J8
Factory Only
JP0
Factory Only
JP1
Factory Only
JP2
Factory Only
JP3
Factory Only
JP4
Factory Only
JP5
Factory Only
JP6
Factory Only
JP7
Factory Only
JP8
Factory Only
JP9
Factory Only
JP10
Disables the intrusion sensor when installed.
SW1
RTFM (see Section 2.1.6, "RTFM Button")
930242A-D
CyberData Corporation
Installing the VoIP Intercom 15
Intercom Setup
2.1.4 Call Button and the Call Button LED
2.1.4.1 Calling with the The Call Button
•
You may initiate a call by pressing the Call button.
•
An active call is indicated by the Call Button LED blinking at one second intervals.
•
The intercom can automatically answer an incoming call.
•
You can press the call button to terminate an active call.
2.1.4.2 Call Button LED Function
•
Upon initial power or reset, the call button LED will illuminate.
•
While the software is setting up the network, the call button led will blink rapidly (10 times/
second).
•
When the software has finished initialization the Call Button LED will blink twice.
•
When a call is established (not just ringing), the Call Button LED will blink.
•
On the Device Configuration Page, there is an option called Button Lit When Idle. This option
sets the normal state for the call button led. The Call Button LED will still blink during
initialization and calls.
•
The Call Button LED will flash briefly at the beginning of RTFM mode.
Figure 2-5. Call Button and Call Button LED
Call Button and Call Button LED
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 16
Intercom Setup
2.1.5 Network Connectivity, and Data Rate
When you plug in the Ethernet cable or power supply:
•
The square, green Link light above the Ethernet port indicates that the network connection has
been established (see Figure 2-6 and Figure 2-7). The Link light changes color to confirm the
auto-negotiated baud rate:
•
This light is yellow at 10 Mbps.
•
It is orange at 100 Mbps.
Figure 2-6. Network Connector Prior to Installation
Ethernet
Link
Activity
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 17
Intercom Setup
2.1.5.1 Verify Network Activity
The square, yellow Activity light blinks when there is network activity.
Figure 2-7. Network Connector
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 18
Intercom Setup
2.1.6 RTFM Button
Caution
GENERAL ALERT
Your intercom will have either an RTFM button or two jumper pins labeled JP11
on the circuit board. If your intercom does not have an RTFM button, use JP11
for IP address announcement and factory reset functions. Intercoms with JP11
jumper pins instead of an SW1 switch correspond to part numbers 010935A,
010935B, 010935C, 010935D, and 010935E. You will need a jumper shunt to
place over the JP11 jumper pins per the instructions below. Intercoms with an
RTFM button correspond to part number 010935F.
When the Intercom is operational and linked to the network, use the Reset Test Function
Management (RTFM) button (see SW1 in Figure 2-8) or place a jumper shunt on the JP11 jumper
pins (see JP11 in Figure 2-9) on the Intercom board to announce and confirm the Intercom's IP
Address and test the audio is working. Your intercom will have an RTMF button or a JP11 jumper but
not both.
Note
You must do these tests prior to final assembly.
Figure 2-8. RTFM Button (SW1)
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 19
Intercom Setup
Figure 2-9. Jumper on JP11
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 20
Intercom Setup
2.1.7 Announcing the IP Address
To announce a device’s current IP address, first determine if you have an Intercom with an RTFM
button (see SW1 in Figure 2-10), and then do one of the following:
•
If you have an Intercom that has an RTFM button, then see Section 2.1.7.1, "Intercom with an
RTFM Button".
•
If you have an Intercom that has a jumper and does not have an RTFM button, then see Section
2.1.7.2, "Intercom with a Jumper and No RTFM Button".
2.1.7.1 Intercom with an RTFM Button
1. If you have an Intercom with an RTFM button, then press and hold the RTFM button (see SW1
in Figure 2-10) until the IP address is announced.
2. Release the Call Button after the IP address is announced.
Figure 2-10. RTFM Button (SW1 Button)
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 21
Intercom Setup
2.1.7.2 Intercom with a Jumper and No RTFM Button
1. If you have an Intercom with a jumper and no RTFM button, then install a jumper on JP11. See
JP11 in Figure 2-11.
2. Wait until the IP address is announced.
3. Remove the jumper and restart the unit.
Figure 2-11. Jumper on JP11
2.1.8 Restore the Factory Default Settings
When troubleshooting configuration problems, it is sometimes convenient to restore the device to a
known state. To restore the factory default settings on your device, do one of the following:
Operations Guide
•
If you have an Intercom that has an RTFM Button, then see Section 2.1.8.1, "Intercom with an
RTFM Button".
•
If you have an Intercom that has a jumper and does not have an RTFM button, then see Section
2.1.8.2, "Intercom with a Jumper".
Note
Each Intercom is delivered with factory set default values.
Note
The device will use DHCP to obtain the new IP address (DHCP-assigned address or default
to 10.10.10.10 if a DHCP server is not present).
930242A-D
CyberData Corporation
Installing the VoIP Intercom 22
Intercom Setup
2.1.8.1 Intercom with an RTFM Button
Complete the following steps to restore defaults on an Intercom that has an RTFM button:
1. Press and hold the RTFM button (SW1 in Figure 2-12) until the Intercom announces the IP
address.
Figure 2-12. RTFM Button (SW1 Button)
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 23
Intercom Setup
2. The Call Button LED (see Figure 2-13) on the front will blink quickly.
3. Press and hold the Call Button until "restoring defaults" is announced.
Figure 2-13. Call Button and Call Button LED
Call Button and Call Button LED
4. Release the Call Button and wait for the Intercom to reboot.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 24
Intercom Setup
2.1.8.2 Intercom with a Jumper
Complete the following steps to restore defaults on an Intercom that has a jumper and no RTFM
button:
1. Put a jumper on JP11. See Figure 2-14.
Figure 2-14. Jumper on JP11
2. Wait for the Intercom to announce the IP address.
3. Press and hold the Call Button (see Figure 2-15) until "restoring defaults" is announced.
4. Release the Call Button and wait for the Intercom to reboot.
5. Remove the jumper and cycle power by unplugging Intercom and plugging it back in.
Figure 2-15. Call Button and Call Button LED
Call Button and Call Button LED
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 25
Intercom Setup
2.1.9 Adjust the Volume
You can adjust the volume through the Speaker Volume setting on the Device Configuration Page.
2.2 Configure the Intercom Parameters
To configure the Intercom online, use a standard web browser.
Configure each Intercom and verify its operation before you mount it. When you are ready to mount
an Intercom, refer to Appendix A, "Mounting the Intercom" for instructions.
All Intercoms are initially configured with the following default IP settings:
When configuring more than one Intercom, attach the Intercoms to the network and configure one at
a time to avoid IP address conflicts.
Table 2-4. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 26
Intercom Setup
2.2.1 Intercom Web Page Navigation
Table 2-5 shows the navigation buttons that you will see on every Intercom web page.
Table 2-5. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device Configuration page.
Link to the Networking page.
Link to go to the SIP Configuration page.
Link to go to the Nightringer page.
Link to the Sensor Configuration page.
Link to the Multicast Configuration page.
Link to the Audio Configuration page.
Link to the Event Configuration page.
Link to the Autoprovisioning Configuration page.
Link to the Update Firmware page.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 27
Intercom Setup
2.2.2 Log in to the Configuration Home Page
1. Open your browser to the Intercom IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Intercom.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
http://www.cyberdata.net/support/voip/discovery_utility.html
Note
The Intercom ships in DHCP mode. To get to the Home page, use the discovery utility to
scan for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-16):
Web Access Username: admin
Web Access Password: admin
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 28
Intercom Setup
Figure 2-16. Home Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 29
Intercom Setup
3. On the Home Page, review the setup details and navigation buttons described in Table 2-6.
Table 2-6. Home Page Overview
Description
Web Page Item
Device Settings
Device Name
Shows the device name.
Change Username
Type in this field to change the username.
Change Password
Type in this field to change the password.
Re-enter Password
Type the password again in this field to confirm the new password.
Current Settings
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Speaker Volume
Shows the current speaker volume level.
Microphone Gain
Shows the current microphone gain level.
SIP Mode is
Shows the current status of the SIP mode.
Multicast Mode is
Shows the current status of the Multicast mode.
Event Reporting is
Shows the current status of the Event Reporting mode.
Nightringer is
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 30
Intercom Setup
2.2.3 Configure the Device
1. Click the Device Configuration button to open the Device Configuration page. See Figure 217.
Figure 2-17. Device Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 31
Intercom Setup
2. On the Device Configuration page, you may enter values for the parameters indicated in
Table 2-7.
Table 2-7. Device Configuration Parameters
Web Page Item
Description
Volume Settings
Speaker Volume
Type the desired Intercom volume level into this field.
Microphone Gain
Type the desired microphone gain level into this field.
Relay Settings
Activate Relay with DTMF Code
When selected, the relay can be activated with a DTMF
code.
DTMF Activation Code
Type the desired DTMF activation code 
(25 character limit).
DTMF Activation Duration (in seconds)
Type the desired DTMF activation duration (in seconds) (2
character limit [activation times now go up to 99 seconds]).
NOTE: A DTMF activation duration of 0 will toggle the
relay indefinitely or until the activation code is sent again
Activate Relay During Ring
When selected, the relay will be activated for as long as
the call is active.
NOTE: When the phone is set to Auto Answer, it will not
ring and this option does nothing.
Activate Relay During Night Ring
Check this box to activate the relay for as long as a Night
Ring tone is ringing.
Activate Relay While Call Active
When selected, the relay will be activated for as long as
the call is active.
Activate Relay on Button Press
When selected, the relay will be activated when the Call
Button is pressed.
Relay on Button Press Timeout (in seconds) Type the desired time (in seconds) that you want the relay
to activate after the Call Button is pressed (1 character
limit).
Miscellaneous Settings
Auto-Answer Incoming Calls
When selected, the device will automatically answer
incoming calls.
When Auto Answer is Off, the device will play a ringtone
through the Intercom speaker until someone presses the
button.
Operations Guide
Button Lit When Idle
When selected, the Call Button remains lit when idle.
Play Ringback Tone
When selected, you will hear a ringback tone while making
a call.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 32
Intercom Setup
Table 2-7. Device Configuration Parameters (continued)
Web Page Item
Description
Enable Push to Talk
This option is for noisy environments. When enabled, the
microphone will be muted normally. When the button is
pressed and held, it will unmute the microphone and allow
the operator to send audio back.
NOTE: When Enable Push to Talk is enabled, you cannot
stop an active call with the call button. The device on the
other end will need to end the call.
NOTE: Enable Push to Talk will not work on some older
hardware.
Volume Boost
When Volume Boost is enabled, the device will play at a
higher volume at the risk of having the audio clip at very
high levels.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Test Audio button to do an audio test. When
the Test Audio button is pressed, you will hear a voice
message for testing the device audio quality and volume.
Click on the Test Relay button to do a relay test.
Click on the Test Microphone button to do a microphone
test. When the Test Microphone button is pressed, the
following occurs:
1. The device will immediately start recording 3 seconds of
audio.
2. The device will beep (indicating the end of recording).
3. The device will play back the recorded audio.
Click on the Reboot button to reboot the system.
Note
Operations Guide
You can change the Speaker Volume and Microphone Gain without rebooting the device.
You must save and reboot the device for other changes to take effect.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 33
Intercom Setup
2.2.4 Configure the Network Parameters
1. Click the Networking button to open the Network Configuration page (Figure 2-18).
Figure 2-18. Network Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 34
Intercom Setup
2. On the Network Configuration page, enter values for the parameters indicated in Table 2-8.
Table 2-8. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
IP Addressing
Select either DHCP IP Addressing or Static IP Addressing by
marking the appropriate radio button. If you select Static, configure
the remaining parameters indicated in Table 2-8. If you select DHCP,
go to Step 3.
IP Address
Enter the Static IP address.
Subnet Mask
Enter the Subnet Mask address.
Default Gateway
Enter the Default Gateway address.
DNS Server 1
Enter the DNS Server 1 address.
DNS Server 2
Enter the DNS Server 2 address.
VLAN ID (0-4095)
Enter the VLAN ID number.
Note: The device supports 802.11Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
VLAN Priority (0-7)
Enter the VLAN priority number.
DHCP Timeout
DHCP Timeout in seconds
Enter the desired timeout duration (in seconds) that the device will
wait for a response from the DHCP server before defaulting back to
the stored static IP address.
Note: A value of -1 will cause the device to retry indefinitely and a
value of 0 will cause the device to reset to a default of 60 seconds.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. You must click on the Save button and then the Reboot button for the changes to take effect.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 35
Intercom Setup
2.2.5 Configure the SIP Parameters
1. Click SIP Config to open the SIP Configuration page (Figure 2-19).
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/support/server/index.html
Figure 2-19. SIP Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 36
Intercom Setup
2. On the SIP Configuration page, enter values for the parameters indicated in Table 2-9.
Table 2-9. SIP Configuration Parameters
Web Page Item
Description
Enable SIP Operation
Enables or disables SIP operation.
SIP Settings
SIP Server
Use this field to set the address (in dotted decimal notation or
as a canonical name) of the SIP registrar. This field can
accept canonical names of up to 255 characters in length.
Backup SIP Server 1
When the primary SIP Server goes offline and the device fails
to register after the normal re-registration interval, the
controller will fall back to using Backup SIP Server 1.
Backup SIP Server 2
If Backup SIP Server 1 fails, the device will use Backup SIP
Server 2.
If a higher priority SIP Server comes back online, the device
will switch back to this server.
You can leave the Backup SIP Server 1 and Backup SIP
Server 2 fields blank.
Use Cisco SRST
When selected, the backup servers are handled according to
Cisco SRST (Survivable Remote Site Telephony).
Remote SIP Port
Type the Remote SIP Port number (default 5060) 
(8 character limit).
Local SIP Port
Type the Local SIP Port number (default 5060) 
(8 character limit).
Outbound Proxy
Type the Outbound Proxy as either a numeric IP address in
dotted decimal notation or the fully qualified host name 
(255 character limit [FQDN]).
Outbound Proxy Port
Type the Outbound Proxy Port number (8 character limit).
SIP User ID
Type the SIP User ID (up to 64 alphanumeric characters).
Authenticate ID
Type the Authenticate ID 
(up to 64 alphanumeric characters).
Authenticate Password
Type the Authenticate Password (up to 64 alphanumeric
characters).
Register with a SIP Server
Check this box to enable SIP Registration.
For information about Point-to-Point Configuration, see
Section 2.2.5.2, "Point-to-Point Configuration".
Operations Guide
Re-registration Interval (in seconds)
The SIP Registration lease time in seconds.
Unregister on Reboot
When selected, on boot, the device will first register with a
SIP server with a expiration delay of 0 seconds. This has the
effect of unregistering any current devices on this extension.
Disable rport discovery
When selected, the device is prevented from including the
public WAN IP address in the contact information sent to
remote SIP servers. This setting will generally only need to be
enabled when using an SBC in conjunction with a remote SIP
server.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 37
Intercom Setup
Table 2-9. SIP Configuration Parameters (continued)
Web Page Item
Description
Call Disconnection
Terminate call after delay (in seconds)
Type the desired number of seconds that you want to
transpire before a call is terminated.
Note: A value of 0 will disable this function.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after
establishing a SIP call. This port number has to be an even
number and defaults to 10500.
Dial Out Settings
Dial Out Extension
Type the dial out extension number (64 character limit).
Note: For information about dial-out extension strings and
DTMF tones, see Section 2.2.5.1, "Dial Out Extension Strings
and DTMF Tones (using rfc2833)".
Extension ID
Type the desired Extension ID (64 character limit).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. You must click on the Save button and then the Reboot button for the changes to take effect.
2.2.5.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the SIP Configuration Page, dial out extensions support the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-10. Examples of Dial-Out Extension Strings
Extension String
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
Resulting Action
The maximum number of total characters in the dial-out field is 64.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 38
Intercom Setup
2.2.5.2 Point-to-Point Configuration
When the board is set to not register with a SIP server (see Figure 2-20), it's possible to set the
intercom to dial out to a single endpoint.
In this case, the dial-out extension should be the IP address of the remote device. The Intercom can
also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point
Mode.
Note
Receiving point-to-point SiP calls may not work with all phones.
Figure 2-20. SIP Configuration Page Set to Point-to-Point Mode
Intercom is set to NOT register with a SIP server
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 39
Intercom Setup
2.2.5.3 Delayed DTMF
On the SIP Configuration page the dial out extension supports the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-11. Examples of Dial-Out Extension Strings
Extension String
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
Resulting Action
The maximum number of total characters in the dial-out field is 25.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 40
Intercom Setup
2.2.6 Configure the Nightringer Parameters
When the Nightringer is enabled, the Intercom will register as a second SIP extension. Registration
does not have to be to the same server as the primary SIP registration. Any calls made to the
Nightringer extension will cause the Intercom to play a ring tone. There is no way to answer this call.
The Nightringer is designed to be used in buildings where calls made after hours are directed to a
ring group.
1. Click on the Nightringer button to open the Nightringer Configuration page. See Figure 2-21.
Figure 2-21. Nightringer Configuration Setup
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 41
Intercom Setup
2. On the Nightringer Configuration page, enter values for the parameters indicated
in Table 2-12.
Table 2-12. Nightringer Configuration Parameters
Web Page Item
Description
Enable Nightringer
When the nightringer is enabled, the unit will attempt to
register a second extension with the SIP server. Any calls
made to this extension will play a ringtone.
Nightringer Settings
SIP Server
Type the SIP server represented as either a numeric IP
address in dotted decimal notation.
Remote SIP Port
Type the Remote SIP Port number (default 5060)
(8 character limit).
Local SIP Port
Type the Local SIP Port number (default 5060)
(8 character limit).
Note: This value cannot be the same as the Local SIP Port
found on the SIP Configuration Page.
Outbound Proxy
Type the Outbound Proxy as either a numeric IP address in
dotted decimal notation or the fully qualified host name 
(255 character limit [FQDN]).
Outbound Proxy Port
Type the Outbound Proxy Port number (5 character limit 
[values from 1 to 65535]).
User ID
Type the User ID (up to 64 alphanumeric characters).
Authenticate ID
Type the Authenticate ID (up to 64 alphanumeric
characters).
Authenticate Password
Type the Authenticate Password (up to 64 alphanumeric
characters).
Re-registration Interval (in seconds)
The SIP Registration lease time in seconds.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. You must click on the Save button and then the Reboot button for the changes to take effect.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 42
Intercom Setup
2.2.7 Configure the Sensor Configuration Parameters
The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state.
There is an option on the Sensor Configuration page to trigger on an open or short condition on
these pins. The door sensor alarm will be activated when the Door Open Timeout parameter has
been met.
The intrusion sensor is an optical sensor installed on the Intercom board and will be activated when
the Intercom is removed from the case.
Each sensor can trigger up to five different actions:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
•
Loop an audio file out of the Intercom speaker until the sensor is deactivated
•
Call an extension and establish two way audio
•
Call an extension and play a pre-recorded audio file
Note
Operations Guide
Calling a preset extension can be set up as a point-to-point call, but currently can't send
delayed DTMF tones.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 43
Intercom Setup
1. Click Sensor Config to open the Sensor Configuration page (Figure 2-22).
Figure 2-22. Sensor Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 44
Intercom Setup
2. On the Sensor Configuration page, enter values for the parameters indicated in Table 2-13.
Table 2-13. Sensor Configuration Parameters
Web Page Item
Description
Door Sensor Settings
Door Sensor Normally Closed
Select the inactive state of the door sensors.
Door Open Timeout (in seconds)
Select the number of seconds that you want to pass before the
door sensor is activated.
Flash Button LED
Check this box to flash the LED until the sensor is deactivated
(roughly 10 times/second).
Activate Relay
Check this box to activate the relay until the sensor is deactivated.
Play Audio Locally
Check this box to loop an audio file out of the Intercom speaker
until the sensor is deactivated.
Make call to extension
Check this box to call a preset extension (once).
Play recorded audio
Check this box to play a pre-recorded audio file (once).
Dial Out Extension
Enter the desired dial-out extension number.
Dial Out ID
Type the desired Extension ID (64 character limit).
Use this button to test the door sensor.
Intrusion Sensor Settings
Flash Button LED
Check this box to flash the LED until the sensor is deactivated
(roughly 10 times/second).
Activate Relay
Check this box to activate the relay until the sensor is deactivated.
Play Audio Locally
Check this box to loop an audio file out of the Intercom speaker
until the sensor is deactivated.
Make call to extension
Check this box to call a preset extension (once).
Play recorded audio
Check this box to play a pre-recorded audio file (once).
Dial Out Extension
Enter the desired dial-out extension number.
Dial Out ID
Type the desired Extension ID (64 character limit).
Use this button to test the Intrusion sensor.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. You must click on the Save button and then the Reboot button for the changes to take effect.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 45
Intercom Setup
2.2.8 Configure the Multicast Parameters
The Multicast Configuration page allows the device to join up to ten paging zones for receiving
ulaw/alaw encoded RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3. The device
supports simultaneous SIP and Multicast.
1. Click on the Multicast Configuration button to open the Multicast Configuration page. See
Figure 2-23.
Figure 2-23. Multicast Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 46
Intercom Setup
2. On the Multicast Configuration page, enter values for the parameters indicated in Table 2-14.
Table 2-14. Multicast Configuration Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Device Settings
Priority
Indicates the priority for the multicast group. Priority 9 is the
highest (emergency streams). 0 is the lowest (background
music). SIP calls are considered priority 4.5. See Section
2.2.8.1, "Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15
character limit).
Port (range can be from 2000 to 65535)
Enter the port number for this multicast group (5 character
limit).
Note: The multicast ports have to be even values. The
webpage will enforce this restriction.
Name
Assign a descriptive name for this multicast group (25
character limit).
Beep
When selected, the device will play a beep before multicast
audio is sent.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. You must click on the Save button and then the Reboot button for the changes to take effect.
2.2.8.1 Assigning Priority
The device will prioritize simultaneous audio streams according to their priority in the list.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams, the volume is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
930242A-D
CyberData Corporation
Installing the VoIP Intercom 47
Intercom Setup
2.2.9 Configure the Audio Configuration Parameters
The Audio Configuration page is used to add custom audio to the board. User uploaded audio will
take precedence over the audio files shipped with the Intercom.
1. Click Audio Config to open the Audio Configuration page (Figure 2-24).
Figure 2-24. Audio Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 48
Intercom Setup
Figure 2-25. Audio Configuration Page (continued)
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 49
Intercom Setup
2. On the Audio Configuration page, enter values for the parameters indicated in Table 2-15.
Table 2-15. Audio Configuration Parameters
Description
Web Page Item
Audio Files
0-9
The name of the audio configuration option is the same as the spoken
audio that plays on the board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Corresponds to the spoken word “dot.” (24 character limit)
Audiotest
Corresponds to the message “This is the CyberData IP speaker test
message...” (24 character limit)
Pagetone
Corresponds to a simple tone used for beep on initialization and beep on
page (24 character limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Restoring default
Corresponds to the message “Restoring default” (24 character limit).
Ringback Tone
This is the ringback tone that plays when calling a remote extension 
(24 character limit).
Ring Tone
This is the tone that plays when set to ring when receiving a call 
(24 character limit).
Intrusion Sensor Triggered
Corresponds to the message “Intrusion Sensor Triggered” 
(24 character limit).
Door Ajar
Corresponds to the message “Door Ajar” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the
same audio file that is selected for the Ring Tone parameter.
The Browse button will allow you to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the
stock audio file.
The Save button will download a new user audio file to the board once
you've selected the file by using the Browse button. The Save button will
delete any pre-existing user-uploaded audio files.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 50
Intercom Setup
2.2.9.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-26 through
Figure 2-28.
Figure 2-26. Audacity 1
Figure 2-27. Audacity 2
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 51
Intercom Setup
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-28. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 52
Intercom Setup
2.2.10 Configure the Event Parameters
Click the Event Config button to open the Event Configuration page (Figure 2-29). The Event
Configuration page specifies a remote server that can be used to receive HTTP POST events
when actions take place on the board.
Figure 2-29. Event Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 53
Intercom Setup
Table 2-16 shows the web page items on the Event Configuration page.
Table 2-16. Event Configuration
Web Page Item
Description
Enable Event Generation
When selected, Event Generation is enabled.
Remote Event Server
Remote Event Server IP
Type the Remote Event Server IP address. 
(64 character limit)
Remote Event Server Port
Type the Remote Event Server port number.
(8 character limit)
Remote Event Server URL
Type the Remote Event Server URL.
(127 character limit)
Events
Enable Button Events
When selected, Button Events are enabled.
Enable Call Active Events
When selected, Call Active Events are enabled.
Enable Call Terminated Events
When selected, Call Terminated Events are enabled.
Enable Relay Activated Events
When selected, Relay Activated Events are enabled.
Enable Relay Deactivated Events
When selected, Relay Deactivated Events are enabled.
Enable Ring Events
When selected, Ring Events are enabled.
Enable Night Ring Events
When selected, there is a notification when the unit
receives a night ring.
Enable Multicast Start Events
When selected, Multicast Start Events are enabled.
Enable Multicast Stop Events
When selected, Multicast Stop Events are enabled.
Enable Power On Events
When selected, Power On Events are enabled.
Enable Door Sensor Events
When selected, Door Sensor Events are enabled.
Enable Intrusion Sensor Events
When selected, Intrusion Sensor Events are enabled.
Enable 60 Second Heartbeat Events
When selected, 60 Second Heartbeat Events are
enabled.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Test Event button to test an event.
Click on the Reboot button to reboot the system.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 54
Intercom Setup
2.2.10.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 55
Intercom Setup
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 56
Intercom Setup
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 57
Intercom Setup
2.2.11 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to configure your device automatically on boot, after a periodic delay,
after sitting idle for a period of time, or at a specified time.
The autoprovisioning file contains the board configuration in xml format. Autoprovisioned values in
this file will override values stored in on-board memory.
The autoprovisioning file can be hosted with a tftp or a web server and by default is named according
to the MAC address of the device (for example: 0020f7350058.config). The autoprovisioning
filename can also be specified.
The device does not have a real time clock but can sync with a network time server on boot.
1. Click the Autoprovisioning button to open the Autoprovisioning Configuration page. 
See Figure 2-30.
Figure 2-30. Autoprovisioning Configuration Page
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 58
Intercom Setup
2. On the Autoprovisioning Configuration page, you may enter values for the parameters
indicated in Table 2-17.
Table 2-17. Autoprovisioning Configuration Parameters
Web Page Item
Description
Autoprovisioning
Enable Autoprovisioning
See Section 2.2.11.1, "Autoprovisioning".
Get Autoprovisioning from DHCP
See Section 2.2.11.1, "Autoprovisioning".
Download Protocol
Allows you to select whether the autoprovisioning file is acquired
via TFTP or HTTP.
Autoprovisioning Server (IP Address) See Section 2.2.11.1, "Autoprovisioning" (15 character limit).
Autoprovisioning Filename
Type the desired name for the autoprovisioning file.
Autoprovisioning Autoupdate 
(in minutes)
Type the desired time (in minutes) that you want the
Autoprovisioning feature to update (6 character limit).
Note: A value of 0 will disable this option.
Autoprovision at time (HHMMSS)
Type the desired time of day that you want the Autoprovisioning
feature to update (must be 6 characters).
Note: An empty value will disable this option.
Autoprovision when idle
(in minutes > 10)
Type the desired time (in minutes greater than 10) that you want
the Autoprovisioning feature to update after a certain amount of
idle time (6 character limit).
Note: A value of 0 will disable this option.
Clock
NTP Server
Allows you to select the NTP server (64 character limit).
Posix Timezone String
See Section 2.2.11.2, "Time Zone Strings" (43 character limit).
Set Time with External NTP Server on When selected, the time is set with an external NTP server when
boot
the device restarts.
Periodically update with time server
When selected, the time is periodically updated with a time
server.
Time update period (in hours)
Allows you to select the time updated period (in hours) 
(4 character limit).
Allows you to set the time from the NTP server.
Current Time
Current Time (UTC) in 24 hour format Allows you to input the current time in the 24 hour format.
(HHMMSS)
(6 character limit)
Click on this button to set the clock after entering the current
time.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click the Save button.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 59
Intercom Setup
2.2.11.1 Autoprovisioning
Autoprovisioning
File
It is not necessary to set every option found in the autoprovisioning template. As long as the XML is
valid, the file can contain any subset. Options not autoprovisioned will default to the values stored in
the on board memory. For example if you only wanted to modify the device name, the following
would be a valid autoprovisioning file:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>auto Intercom</DeviceName>
</MiscSettings>
</specific>
Get
Autoprovisioning
from DHCP
When this option is checked, the device will automatically fetch its autoprovisioning server address
from the DHCP server. The device will use the address specified in OPTION 150 (TFTP-servername) or OPTION 66. If both options are set, the device will use OPTION 150.
Refer to the documentation of your DHCP server for setting up OPTION 150.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 60
Intercom Setup
To set up a Linux DHCPD server to serve autoprovisioning information (in this case using both
option 66 and 150), here's an example dhcpd.conf:
# dhcpd.conf
#
# Configuration file for ISC dhcpd (see 'man dhcpd.conf')
#
ddns-update-style ad-hoc;
option option-150 code 150 = ip-address;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 120;
default-lease-time 120;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.1;
option time-offset
-8;
option tftp-server-name
"10.0.0.254";
option option-150
10.0.0.254;
# Pacific Standard Time
range 10.10.0.1 10.10.2.1;}
Autoprovisioning Instead of using DHCP to provide the autoprovisioning tftp server address, you can specify an
Server (IP Address) address manually.
Autoprovisioning
Autoupdate
When the device is set to autoprovision either after a period of time, or when idle, or at a time of day,
the device will do the following:
•
Re-download the autoprovisioning file.
•
Compare this new file to the one downloaded on boot, and if it finds differences, force a system
reset.
•
After rebooting, the board will configure itself according to this new file.
Autoprovisioned An Autoprovisioned firmware upgrade only happens after a reboot, will take roughly three minutes,
Firmware Upgrades and the web page will be unresponsive during this time.
The 'FirmwareVersion' value in the xml file must match the version stored in the 'FirmwareFile'.
<FirmwareVersion>v6.5.1</FirmwareVersion>
<FirmwareFile>651-intercom-uImage</FirmwareFile>
If these values are mismatched, the board can get stuck in a loop where it goes through the following
sequence of actions:
1. The board downloads and writes a new firmware file.
2. After the next reboot, the board recognizes that the firmware version does not match.
3. The board downloads and writes the firmware file again.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 61
Intercom Setup
CyberData has timed a firmware upgrade at 140 seconds. Therefore, if you suspect the board is
stuck in a loop, either remove or comment out the FirmwareVersion line in the XML file and let the
board boot as it normally does.
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio Configuration page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 62
Intercom Setup
2.2.11.2 Time Zone Strings
The posix time zone string tells the internal date and time utilities how to handle daylight savings
time for different time zones. Table 2-18 shows some common strings.
Table 2-18. Common Time Zone Strings
Time Zone
Time Zone String
US Pacific time
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Mountain time
MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Eastern Time
EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00
a
Phoenix Arizona
MST7
US Central Time
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
a.Phoenix, Arizona does not use daylight savings time.
Table 2-19 shows a breakdown of the parts that constitute the following time zone string:
●
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
Table 2-19. Time Zone String Parts
Operations Guide
Time Zone String
Part
Meaning
CST6CDT
The time zone offset from GMT and three character identifiers for the time zone.
CST
Central Standard Time
6
The (hour) offset from GMT/UTC
CDT
Central Daylight Time
M3.2.0/2:00:00
The date and time when daylight savings begins.
M3
The third month (March)
.2
The 2nd occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
M11.1.0/2:00:00
The date and time when daylight savings ends.
M11
The eleventh month (November)
.1
The 1st occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
930242A-D
CyberData Corporation
Installing the VoIP Intercom 63
Intercom Setup
Time Zone String
Examples
Table 2-20 has some more examples of time zone strings.
Table 2-20. Time Zone String Examples
Time Zone
Time Zone String
a
Tokyo
IST-9
Berlinb
CET-1MET,M3.5.0/1:00,M10.5.0/1:00
a.Tokyo does not use daylight savings time.
b.For Berlin, daylight savings time starts on the last Sunday in March at
01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one
hour ahead of UTC.
Time Zone Identifier A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is
needed at the beginning of the posix time zone string to properly set the time. However, the specific
letters or numbers used for the time zone identifier are not important and can be any three or four
letter or number combination that is chosen by the user. However, the time zone identifier cannot be
blank.
Figure 2-31. Three or Four Character Time Zone Identifier
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
Three or four character time zone identifier at the beginning of the time zone string.
The identifier can be any three or four letter or number combination chosen by the user.
You can also use the following URL when a certain time zone applies daylight savings time:
http://www.timeanddate.com/time/dst/2011.html
World GMT Table
Table 2-21 has information about the GMT time in various time zones.
Table 2-21. World GMT Table
Operations Guide
Time Zone
City or Area Zone Crosses
GMT-12
Eniwetok
GMT-11
Samoa
GMT-10
Hawaii
GMT-9
Alaska
GMT-8
PST, Pacific US
GMT-7
MST, Mountain US
GMT-6
CST, Central US
GMT-5
EST, Eastern US
GMT-4
Atlantic, Canada
GMT-3
Brazilia, Buenos Aries
GMT-2
Mid-Atlantic
GMT-1
Cape Verdes
GMT
Greenwich Mean Time, Dublin
930242A-D
CyberData Corporation
Installing the VoIP Intercom 64
Intercom Setup
Table 2-21. World GMT Table (continued)
Operations Guide
Time Zone
City or Area Zone Crosses
GMT+1
Berlin, Rome
GMT+2
Israel, Cairo
GMT+3
Moscow, Kuwait
GMT+4
Abu Dhabi, Muscat
GMT+5
Islamabad, Karachi
GMT+6
Almaty, Dhaka
GMT+7
Bangkok, Jakarta
GMT+8
Hong Kong, Beijing
GMT+9
Tokyo, Osaka
GMT+10
Sydney, Melbourne, Guam
GMT+11
Magadan, Soloman Is.
GMT+12
Fiji, Wellington, Auckland
930242A-D
CyberData Corporation
Installing the VoIP Intercom 65
Intercom Setup
2.3 Upgrade the Firmware and Reboot the Intercom
Note
To guard against failed firmware upgrades, units shipped from CyberData with firmware
version 5.1.2 and later feature a built-in "fail safe" mechanism. Note that field upgrading
earlier units with v5.x.x will not allow for this feature.
Note
Any units that have shipped with firmware version 6.0.0 or later will not be able to run
firmware that is version 5.1.2 or earlier.
Caution
GENERAL ALERT
When upgrading to firmware version 6.x.x from version 5.x.x or earlier, your
device configuration settings will be lost because the way that the device stores
the configuration settings is different in version 6.x.x.
To upload the firmware from your computer:
1. Retrieve the latest Intercom firmware file from the VoIP Intercom Downloads page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercom/downloads.html
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the Intercom home page as instructed in Section 2.2.2, "Log in to the Configuration
Home Page".
4. Click the Update Firmware button to open the Upgrade Firmware page. See Figure 2-32.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 66
Intercom Setup
Figure 2-32. Upgrade Firmware Page
5. Select Browse, and then navigate to the location of the Intercom firmware file.
6. Click Submit.
Note
This starts the upgrade process. Once the Intercom has uploaded the file, the Uploading
Firmware countdown page appears, indicating that the firmware is being written to flash.
The Intercom will automatically reboot when the upload is complete. When the countdown
finishes, the Upgrade Firmware page will refresh. The uploaded firmware filename should
be displayed in the system configuration (indicating successful upload and reboot).
Table 2-22 shows the web page items on the Upgrade Firmware page.
Table 2-22. Firmware Upgrade Parameters
Description
Web Page Item
File Upload
Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
Intercom firmware file that you want to upload.
Click on the Submit button to automatically upload the
selected firmware and reboot the system.
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 67
Intercom Setup
2.3.1 Reboot the Intercom
To reboot a Intercom, log in to the web page as instructed in Section 2.2.2, "Log in to the
Configuration Home Page".
1. Click Reboot (Figure 2-33). A normal restart will occur.
Figure 2-33. Reboot System Section
Reboot
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 68
Intercom Setup
2.4 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-23 use the free unix utility, wget commands. However, any program that
can send HTTP POST commands to the device should work.
2.4.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-23. Command Interface Post Commands
HTTP Post Commanda
Device Action
Trigger relay (for configured delay)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"test_relay=yes"
Place call to extension (example: extension 130)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"call=130"
Place point-to-point callb 
(example: IP phone address = 10.0.3.72)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"call=10.0.3.72"
Terminate active call
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"reboot=yes"
Test Audio button
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"test_audio=yes"
Announce IP address
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"speak_ip_address=yes"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_0=yes"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_1=yes"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_2=yes"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_3=yes"
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 69
Intercom Setup
Table 2-23. Command Interface Post Commands (continued)
HTTP Post Commanda
Device Action
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_4=yes"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringtone=yes"
Play the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_intrusionsensortriggered=yes"
Play the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_doorajar=yes"
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 70
Intercom Setup
Table 2-23. Command Interface Post Commands (continued)
HTTP Post Commanda
Device Action
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_4=yes"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringtone=yes"
Play the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_intrusionsensortriggered=yes"
Play the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_doorajar=yes"
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 71
Intercom Setup
Table 2-23. Command Interface Post Commands (continued)
HTTP Post Commanda
Device Action
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_4=yes"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringtone=yes"
Play the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_intrusionsensortriggered=yes"
Play the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_doorajar=yes"
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 72
Intercom Setup
Table 2-23. Command Interface Post Commands (continued)
HTTP Post Commanda
Device Action
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_nightring=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_1=yes"
Delete the "2" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_2=yes"
Delete the "3" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_3=yes"
Delete the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_4=yes"
Delete the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_5=yes"
Delete the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_6=yes"
Delete the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_7=yes"
Delete the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_8=yes"
Delete the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_9=yes"
Delete the "Audio Test" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_audiotest=yes"
Delete the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_pagetone=yes"
Delete the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_youripaddressis=yes"
Delete the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_rebooting=yes"
Delete the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_restoringdefault=yes"
Operations Guide
930242A-D
CyberData Corporation
Installing the VoIP Intercom 73
Intercom Setup
Table 2-23. Command Interface Post Commands (continued)
HTTP Post Commanda
Device Action
Delete the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_ringback=yes"
Delete the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_ringtone=yes"
Delete the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_intrusionsensortriggered=yes"
Delete the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_doorajar=yes"
Delete the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_nightring=yes"
Trigger the Door Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/sensorconfig.cgi" --post-data
"doortest=yes"
Trigger the Intrusion Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/sensorconfig.cgi" --post-data
"intrusiontest=yes"
a.Type and enter all of each http POST command on one line.
b. Must be in point-to-point mode see Section 2.2.5.2, "Point-to-Point Configuration"
Operations Guide
930242A-D
CyberData Corporation
74
Appendix A: Mounting the Intercom
A.1 Mount the Intercom
Before you mount the Intercom, make sure that you have received all the parts for each Intercom.
Refer to Table A-1.
Table A-1. Mounting Components (Part of the Accessory Kit)
Operations Guide
Quantity
Part Name
2
Outlet Box Plugs
2
Flush Mounting Plate
2
8-32 x 1/4" Flat Head Phillips Machine Screw
1
10-24 x 5/16" Pan Head Phillips Machine
Screw
1
T-15H Torx Key
4
Security Torx Screw
930242A-D
Illustration
CyberData Corporation
75
Mount the Intercom
To mount the Intercom:
1. Plug the Ethernet cable into the Intercom Assembly (see Figure A-1). Section 2.1.5, "Network
Connectivity, and Data Rate" explains how the Link and Status LEDs work.
Figure A-1. Network Connector Prior to Installation
Ethernet
Link
Activity
Operations Guide
930242A-D
CyberData Corporation
76
Mount the Intercom
2. To fasten the Intercom:
•
For wall mounting, use the two 8-32 X 1/4" FLAT HEAD PHILLIPS MACHINE SCREW and
the one 10-24 X 5/16" PAN HEAD PHILLIPS MACHINE SCREW to secure the Intercom.
Figure A-2. VoIP Intercom Assembly
2 Gang Box
Face Plate
and
PCB Assembly
Security Torx Screw (4x)
(1) Tamper-resistant T-15H Torx Key
needed for Security Torx Screws
Caution
GENERAL ALERT
Operations Guide
Equipment Hazard: Do not use an electric or power screwdriver to fasten the face
plate and PCB assembly to the gang box. To prevent over-torque damage to the
gasket, do not apply more than 10 inch-pounds force. Over-torquing will cause the
gasket to tear, risk moisture intrusion, and effectively void the manufacturer's
warranty.
930242A-D
CyberData Corporation
77
Mount the Intercom
If the thread on the conduit is longer than 3/8 inch, then a stop nut (not supplied) is required.
Otherwise, use the outlet box plug to plug the exit hole.
Note
Apply good quality waterproof sealant to all threads.
Figure A-3. Mounting the VoIP Intercom Assembly
Apply good quality waterproof
sealant to all threads.
HOLE PLUG
OR
CONDUIT
Figure A-4 shows the restrictions of the conduit going into the box.
Figure A-4. Conduit Restrictions
Not to Exceed 0.1"
Operations Guide
930242A-D
CONDUIT (1/2”)
CyberData Corporation
78
Mount the Intercom
Figure A-5 shows how to properly mount the VoIP Intercom.
Figure A-5. Mounting
Flush Mounting
Plate (2x)
Flat Head Phillips
Machine Screw (2x)
Mounting Screw
(Not Provided)
Operations Guide
930242A-D
CyberData Corporation
Figure A-6 shows how to do a custom flush mounting for the VoIP Intercom.
Figure A-6. Custom Flush Mounting
DEPTH
BELOW GASKET
5.00 [127.0]
1.70 [43.2]
930242A-D
3.27 [83.1]
4.40 [111.8]
A
0.35 [8.9] REF.
0.10 [2.5]
0.57 [14.4] REF.
MH
MH
MH
MH
5.05 [128.3]
3.70 [94.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
PROJECTION: THIRD ANGLE PROJECTION
4.40 [111.8]
Operations Guide
A.1.1 Custom Flush Mounting
A
0.20 [5.2]
FACEPLATE + GASKET
VIEW A-A
Mount the Intercom
CyberData Corporation
CUTOUT FOR PCBA
NOTE: 1) JUST A SUGGESTION:
ASSUMING LEAVING 0.10 [2.5]
(IT COULD BE LESS)
GAP BETWEEN PCB AND CUTOUT
TO CLEAR ANY OBSTRUCTIONS
2) MH = MOUNTING HOLE
79
80
Appendix B: Setting up a TFTP Server
B.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
B.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download from the following
website address:
http://www.cyberdata.net/support/voip/solarwinds.html
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
930242A-D
CyberData Corporation
81
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
A list of frequently asked questions (FAQs) are available on the VoIP Intercom product page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercom/faqs.html
Select the support page for your product to see a list of frequently asked questions for the
CyberData product:
C.2 Documentation
The documentation for this product is released in an English language version only. 
You can download PDF copies of CyberData product documentation from the
VoIP Intercom product page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercom/docs.html
Operations Guide
930242A-D
CyberData Corporation
82
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601 Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://www.cyberdata.net/support/contactsupportvoip.php
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Returned
Materials
Authorization
To return the product, contact the Returned Materials Authorization (RMA) department:
Phone: 831-373-2601, Extension 136
Email: RMA@CyberData.net
When returning a product to CyberData, an approved CyberData RMA number must be printed
on the outside of the original shipping package. Also, RMA numbers require an active VoIP
Technical Support ticket number. A product will not be accepted for return without an approved
RMA number. Send the product, in its original package, to the following address:
CyberData Corporation
3 Justin Court 
Monterey, CA 93940 
Attention: RMA "your RMA number"
RMA Status Form If you need to inquire about the repair status of your product(s), please use the CyberData RMA
Status form at the following web address:
http://www.cyberdata.net/support/rmastatus.html
Operations Guide
930242A-D
CyberData Corporation
83
Warranty
C.4 Warranty
CyberData warrants its product against defects in material or workmanship for a period of two
years from the date of purchase. Should the product fail Within Warranty, CyberData will repair
or replace the product free of charge. This warranty includes all parts and labor.
Should the product fail Out of the Warranty period, a flat rate repair charge of one half of the
purchase price of the product will be assessed. Repairs that are Within Warranty period but are
damaged by improper installation, modification, or abuse are deemed Out of Warranty and will
be charged at the Out of Warranty rate. A device is deemed Out of Warranty when its purchase
date is longer than two years or when the device has been damaged due to human error during
installation, modification, or abuse. A replacement unit will be offered at full cost if the device
cannot be repaired.
End of Life Devices are included under this policy. End of Life devices are devices that are no
longer produced or sold. Technical support is still available for these devices. However, no
firmware revisions or updates will be provided. If an End of Life device cannot be repaired, the
replacement offered may be the current version of the device.
Products shipped to CyberData, both within and out of warranty, are shipped at the expense of
the customer. CyberData will pay return shipping charges for repaired products.
CyberData shall not under any circumstances be liable to any person for any special, incidental,
indirect or consequential damages, including without limitation, damages resulting from use or
malfunction of the products, loss of profits or revenues or costs of replacement goods, even if
CyberData is informed in advance of the possibility of such damages.
C.4.1 Warranty & RMA Returns within the United States
If service is required, you must contact CyberData Technical Support prior to returning any
products to CyberData. Our Technical Support staff will determine if your product should be
returned to us for further inspection. If Technical Support determines that your product needs to
be returned to CyberData, an RMA number will be issued to you at this point.
Your issued RMA number must be printed on the outside of the shipping box. No product will be
accepted for return without an approved RMA number. The product in its original package
should be sent to the following address:
CyberData Corporation
3 Justin Court.
Monterey, CA 93940
Attn: RMA "xxxxxx"
C.4.2 Warranty & RMA Returns outside of the United States
If you purchased your equipment through an authorized international distributor or reseller,
please contact them directly for product repairs.
Operations Guide
930242A-D
CyberData Corporation
84
Warranty
C.4.3 Spare in the Air Policy
CyberData now offers a Spare in the Air no wait policy for warranty returns within the United
States and Canada. More information about the Spare in the Air policy is available at the
following web address:
http://www.cyberdata.net/support/warranty/spareintheair.html
C.4.4 Return and Restocking Policy
For our authorized distributors and resellers, please refer to your CyberData Service
Agreement for information on our return guidelines and procedures.
For End Users, please contact the company that you purchased your equipment from for their
return policy.
C.4.5 Warranty and RMA Returns Page
The most recent warranty and RMA information is available at the CyberData Warranty and
RMA Returns Page at the following web address:
http://www.cyberdata.net/support/warranty/index.html
Operations Guide
930242A-D
CyberData Corporation
85
Index
Numerics
C
100 Mbps indicator light 16
16 AWG gauge wire 10
call button 15
LED 15
call button LED 15
changing
the web access password 30
Chrome (web browser) 3
Cisco SRST 36
command interface 68
commands 68
conduit restrictions 77
configurable parameters 29, 31, 34, 36, 66
configuration
audio 47
default IP settings 25
door sensor 42
intrusion sensor 42
network 33
SIP 35
using Web interface 25
configuration home page 27
configuration page
configurable parameters 29, 31, 34
contact information 82
contact information for CyberData 82
Current Network Settings 34
current network settings 34
CyberData contact information 82
A
AC voltages 3
AC voltages, intercom enclosure is not rated 11
act light 17
activate relay (door sensor) 44
activate relay (intrusion sensor) 44
address, configuration login 27
audio configuration 47
night ring tone parameter 49
audio configuration page 47
audio encodings 5
audio files, user-created 50
Autoprovision at time (HHMMSS) 58
autoprovision at time (HHMMSS) 58
autoprovision when idle (in minutes > 10) 58
autoprovisioning 59
autoprovisioned audio files 61
autoprovisioned firmware upgrades 60
autoprovisioning autoupdate 60
autoprovisioning from DHCP 59
autoprovisioning server (IP address) 60
setting up a TFTP server 80
autoprovisioning autoupdate (in minutes) 58
autoprovisioning configuration 57, 58
autoprovisioning filename 58
auxiliary relay 11
auxiliary relay wiring diagram 12
auxiliary relay, 1A at 30 VDC 6
D
default
gateway 25
intercom settings 85
IP address 25
subnet mask 25
username and password 25
web login username and password 27
default gateway 25, 34
default intercom settings 21
default IP settings 25
default login address 27
device configuration 30
device configuration parameters 58
the device configuration page 57
device configuration page 30
device configuration parameters 31
device configuration password
changing for web configuration access 30
B
backup SIP server 1 36
backup SIP server 2 36
backup SIP servers, SIP server
backups 36
baud rate
verifying 16
Operations Guide
930242A-D
CyberData Corporation
86
DHCP Client 5
DHCP IP addressing 34
dial out extension (door sensor) 44
dial out extension (intrusion sensor) 44
dial out extension strings 37
dial-out extension strings 39
dimensions 6, 7
disable rport discovery 36
discovery utility program 27
DNS server 34
door sensor 42, 44, 49
activate relay 44
dial out extension 44
door open timeout 44
door sensor normally closed 44
flash button LED 44
play audio locally 44
door strike
cannot be powered by alternate power input nor PoE
power 10
download protocol, HTTP or TFTP 58
DTMF tones 37, 39
DTMF tones (using rfc2833) 37
dual speeds 16
E
electric screwdriver 76
enable night ring events 53
ethernet cable 75
event configuration
enable night ring events 53
expiration time for SIP server lease 36, 41
green link light 16
H
home page 27
http POST command 68
http web-based configuration 5
I
identifier names (PST, EDT, IST, MUT) 63
identifying your product 1
illustration of intercom mounting process 74
installation, typical intercom system 2
intercom configuration
default IP settings 25
intercom configuration page
configurable parameters 36, 66
Internet Explorer (web browser) 3
intrusion sensor 42, 44
activate relay 44
dial out extension 44
flash button LED 44
play audio locally 44
IP address 25, 34
IP addressing 34
default
IP addressing setting 25
J
J3 terminal block, 16 AWG gauge wire 10
F
factory default settings 21
fastening, gang box 76
Firefox (web browser) 3
firmware
where to get the latest firmware 65
flash button LED (door sensor) 44
flash button LED (intrusion sensor) 44
flush mounting, custom 79
L
lease, SIP server expiration time 36, 41
lengthy pages 46
link LED 75
link light 16
Linux, setting up a TFTP server on 80
local SIP port 36
log in address 27
G
M
gang box, fastening 76
gasket, avoid over-torque damage 76
GMT table 63
GMT time 63
Operations Guide
MGROUP
MGROUP Name 46
930242A-D
CyberData Corporation
87
mounting an intercom 74
Mozilla Firefor (web browser) 3
multicast configuration 45
Multicast IP Address 46
product overview
product features 4
product specifications 6
supported protocols 5
supported SIP servers 5
typical system installation 2
product specifications 6
protocol 6
protocols supported 5
N
navigation (web page) 26
navigation table 26
network activity, verifying 17
network configuration of intercom 33
Network Setup 33
nightring tones 46
Nightringer 10
nightringer settings 41
NTP server 58
R
reboot 66, 67
remote SIP port 36
reset test function management button 18
resetting the IP address to the default 74, 81
restoring factory default settings 21, 85
return and restocking policy 84
ringtones 46
lengthy pages 46
RJ-45 14
RMA returned materials authorization 82
RMA status 82
rport discovery 36
RTFM button 18
RTFM jumper 18, 20, 21, 22, 24
RTP/AVP 5
O
operating temperature 6
orange link light 16
P
packet time 5
pages (lengthy) 46
part number 6
parts list 9
password
for SIP server login 36
login 27
restoring the default 25
payload types 6
play audio locally (door sensor) 44
play audio locally (intrusion sensor) 44
point-to-point configuration 38
port
local SIP 36
remote SIP 36
posix timezone string
timezone string 58
POST command 68
power input 6
power screwdriver 76
priority
assigning 46
product
configuring 25
mounting 74
parts list 9
product features 4
Operations Guide
S
Safari (web browser) 3
sales 82
sensor setup page 43
sensor setup parameters 42
sensors 44
server address, SIP 36
service 82
set the time from the NTP server 58
set time with external NTP server on boot 58
setting up an intercom 10
settings, default 21
SIP
enable SIP operation 36
local SIP port 36
user ID 36
SIP (session initiation protocol) 5
SIP configuration 35
SIP Server 36
SIP configuration parameters
outbound proxy 36, 41
registration and expiration, SIP server lease 36, 41
unregister on reboot 36
930242A-D
CyberData Corporation
88
W
user ID, SIP 36
SIP registration 36
SIP remote SIP port 36
SIP server 36
password for login 36
SIP servers supported 5
unregister from 36
user ID for login 36
SIP settings 37
Spare in the Air Policy 84
speaker output 6
SRST 36
static IP addressing 34
status LED 75
subnet mask 25, 34
supported protocols 5
warranty 83
warranty & RMA returns outside of the United States 83
warranty and RMA returns page 84
warranty policy at CyberData 83
web access password 25
web access username 25
web configuration log in address 27
web page
navigation 26
web page navigation 26
web-based intercom configuration 25
weight 6
wget, free unix utility 68
Windows, setting up a TFTP server on 80
T
Y
tech support 82
technical support, contact information 82
terminal block, 16 AWG gauge wire 10
TFTP server 5, 80
time zone string examples 63
yellow act light 17
yellow link light 16
U
upgrading to firmware 6.x.x from 5.x.x 65, 76
user ID
for SIP server login 36
username
changing for web configuration access 30
default for web configuration access 27
restoring the default 25
V
verifying
baud rate 16
network activity 17
network connectivity 16
VLAN ID 34
VLAN Priority 34
VLAN tagging support 34
VLAN tags 34
volume boost 32
Operations Guide
930242A-D
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising