CyberData | 010935 | Quick Reference | Cyberdata 010935 SIP-enabled IP Outdoor Intercom (Replacement Product Below) Quick Reference

Cyberdata 010935 SIP-enabled IP Outdoor Intercom (Replacement Product Below) Quick Reference
Intercom Connections
Installation Quick Reference
VoIP Intercom
SiP Compliant
010935
6
5
Wire in,
accept wire range
from 16-26 AWG
4
3
2
-
1
Parameter
Factory Default Setting
IP Addressing
static
IP Address
192.168.3.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
255.255.255.0
Default Gateway
192.168.3.1
J3 - Terminal Block
-
Typical Intercom System Installation
Alternate Power Input:
1 = +5V at 1000 mA
2 = Power Ground
802.3af Compliant Ethernet Hub
3
4
Relay Contact:
(2A at 30 VDC or 0.4A at 125 VAC
for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
1
VoIP Intercom
V2 Hardware
3
4
VoIP Intercom
5
6
IP Phone
IP PBX Server
Getting Started
Contacting CyberData
●
Warranty
CyberData Corporation
2555 Garden Road
Monterey, CA 93940, USA
CyberData warrants its product against defects in material and
workmanship for a period of two years from the date of purchase.
Should the product fail within the warranty period, CyberData will
repair or replace the product free of charge. This warranty includes all
parts and labor. Should the product fail out-of-warranty, a flat rate
repair charge of one half the purchase price will be assessed. Repair
costs for products that are in warranty, but damaged by improper
modifications or abuse, are charged at the out-of-warranty rate.
Products returned to CyberData, both in and out-of-warranty, are
shipped to CyberData at the customer’s expense. Charges for
shipping repaired products to the customer are paid by CyberData.
Phone: 831-373-2601
Fax: 831-373-4193
www.CyberData.net
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Email: support@CyberData.net
Download the VoIP Intercom Operations Guide PDF file, from the VoIP Intercom product page at:
http://www.cyberdata.net/support/voip/index.html
Corporate Headquarters
●
Create a plan for the locations of your Intercoms.
●
Prior to installation, consult local building and electrical code requirements.
●
WARNING: This enclosure is not rated for any AC voltages!
Intercom Parts
(1) Intercom Assembly
For product service, contact the Returned Materials Authorization
(RMA) department. A product will not be accepted for return without
an approved RMA number. Send the product, in its original package,
to: CyberData Corporation, 2555 Garden Road, Monterey, CA 93940,
Attention: RMA “your RMA number”
RMA Dept: (831) 373-2601 ext. 136
Email: RMA@CyberData.net
© 2009, CyberData Corporation, ALL RIGHTS RESERVED
VoIP Intercom
2
930180E
Quick Reference
Quick Reference
(1) Wall Mounting Kit
(2) Outlet box plugs
(2) 8-32 x 1/4" Flat head
phillips machine screw
(2) Flush mounting plate
(1) 10-24 x 5/16" Pan head
phillips machine screw
930180E
© 2009, CyberData Corporation, ALL RIGHTS RESERVED
Intercom Assembly
Cable Entries and Conduit Restrictions
To mount the intercom, use methods compliant with local electrical codes.
The VoIP Intercom has three possible cable entries. If you are using the center entry, refer to the drawing on the right that
shows the entry restrictions.
Mounting
Screw (4x)
Face Plate
and
PCB Assembly
HOLE PLUG
OR
CONDUIT (1/2”)
Not to Exceed 0.1"
2 Gang Box
1/2"
CONDUIT
Mounting and Screws
Flush Mounting
Plate (2 x)
Flat Head Phillips
Machine Screw (2 x)
Intercom Dimensions
5.0 [127]
5.0 [127]
Mounting Screw
Not Provided
2.3 [59]
inches [millimeter]
© 2009, CyberData Corporation, ALL RIGHTS RESERVED
930180E
Quick Reference
Quick Reference
930180E
© 2009, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising