Taylor | Model 8756 Single Stage Pump | Owner Manual | Taylor Model 8756 Single Stage Pump User manual

Taylor Model 8756 Single Stage Pump User manual
OPERATOR'S
MANUAL
Model 8756
Single Stage Pump
Soft Serve Freezer
Original Operating Instructions
069071-M
11/15/10 (Original Publication)
(Updated 7/1/16)
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Fax:
E-mail:
Service:
Parts:
Date of Installation:
Information found on the data label:
Model Number:
Serial Number:
Electrical Specs:
Voltage
Cycle
Phase
Maximum Fuse Size:
A
Minimum Wire Ampacity:
A
E 2010 Taylor Company
069071-M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this
work may be a violation of Copyright Law of the United States of America and other countries, could result
in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result
in further civil and criminal penalties. All rights reserved.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Water Connections (Water Cooled Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Section 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Section 4
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Beater Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Air/Mix Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Indicator Lights - MIX LOW and MIX OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
MIX REF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Adjustable Draw Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Air/Mix Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Table of Contents
Model 8756
Table of Contents - Page 2
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Draining Product From the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
Section 7
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
The Air/Mix Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Section 9
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Section 10
Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
Section 11
Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E 2010 Taylor Company (Original Publication)
(Updated April, 2015)
069071-M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this
work may be a violation of Copyright Law of the United States of America and other countries, could result
in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result
in further civil and criminal penalties. All rights reserved.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Model 8756
Table of Contents
Section 1
To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the
Installation Checklist.
Site Preparation
Review the area where the unit will be installed
before uncrating the unit. Make sure all possible
hazards to the user or equipment have been
addressed.
Installer Safety
For Indoor Use Only: This unit is designed to
operate indoors, under normal ambient
temperatures of 70_­75_F (21_­24_C). The freezer
has successfully performed in high ambient
temperatures of 104_(40_C) at reduced capacities.
In all areas of the world, equipment should
be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
servicing of Taylor equipment.
S
S
S
S
This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use
a water jet or hose to rinse or clean the unit. Failure
to follow this instruction may result in electrocution.
Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should
be taken when moving this equipment for any
reason. Two or more people are required to safely
move this unit. Failure to comply may result in
personal injury or equipment damage.
Uncrate the unit and inspect it for damage. Report
any damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.
The main power supply(s) to the freezer
must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.
Air Cooled Units
DO NOT obstruct air intake and discharge openings:
Air cooled units require a minimum of 3” (76 mm) of
clearance around all sides of the freezer and 12”
(305 mm) on top to allow for adequate air flow
across the condenser(s). Failure to allow adequate
clearance can reduce the refrigeration capacity of
the freezer and possibly cause permanent damage
to the compressor.
Note: All repairs must be performed by an
authorized Taylor Service Technician.
This unit has many sharp edges that can
cause severe injuries.
131220
Model 8756
1
To the Installer
Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the
freezer for branch circuit overcurrent protection or
fuse, circuit ampacity, and other electrical
specifications. Refer to the wiring diagram provided
inside of the electrical box for proper power
connections.
Water Connections
(Water Cooled Units Only)
An adequate cold water supply must be provided
with a hand shut-off valve. On the underside of the
base pan, two 3/8” I.P.S. (for single-head units) or
two 1/2” I.P.S. (for double-head units) water
connections for inlet and outlet have been provided
for easy hook-up. 1/2” inside diameter water lines
should be connected to the machine. (Flexible lines
are recommended, if local codes permit.) Depending
on local water conditions, it may be advisable to
install a water strainer to prevent foreign substances
from clogging the automatic water valve. There will
be only one water “in” and one water “out”
connection for both single-head and double-head
units. DO NOT install a hand shut-off valve on the
water “out” line! Water should always flow in this
order: first, through the automatic water valve;
second, through the condenser; and third, through
the outlet fitting to an open trap drain.
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417­1) on both the
removable panel and the equipment's frame.
A back flow prevention device is
required on the incoming water connection side.
Please refer to the applicable National, State, and
local codes for determining the proper configuration.
Electrical Connections
In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70­1987. The
purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety. In all
other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.
FOLLOW YOUR LOCAL ELECTRICAL CODES!
To the Installer
2
S
Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all­pole
disconnecting device with a contact gap of
at least 3 mm installed in the external
installation.
S
Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
Model 8756
S
Supply cords used with this unit shall be
oil­resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or oth­
er equivalent synthetic elastomer­sheathed
cord (Code designation 60245 IEC 57) in­
stalled with the proper cord anchorage to
relieve conductors from strain, including
twisting, at the terminals and protect the in­
sulation of the conductors from abrasion.
Refrigerant
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
However, any gas under pressure is potentially
hazardous and must be handled with caution.
In consideration of our environment, Taylor
uses only HFC refrigerants. The HFC refrigerant
used in this unit is R404A. This refrigerant is
generally considered non­toxic and non­flammable,
with an Ozone Depleting Potential (ODP) of zero (0).
NEVER fill any refrigerant cylinder completely with
liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.
Use only R404A refrigerant that conforms
to the AHRI standard 700 specification. The use of
any other refrigerant may expose users and
operators to unexpected safety hazards.
Beater Rotation
Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe,
apply ice packs and contact a physician
immediately.
Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
The following procedures must be
performed by an authorized Taylor service
technician.
Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory Service Department.
To correct the rotation on a three-phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.
WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely
moisture absorbent. When opening a refrigeration
system, the maximum time the system is open must
not exceed 15 minutes. Cap all open tubing to
prevent humid air or water from being absorbed by
the oil.
To correct rotation on a single-phase unit, change
the leads inside the beater motor. (Follow the
diagram printed on the motor.)
Electrical connections are made directly to the
terminal block provided in the main control box.
131220
Model 8756
3
To the Installer
Section 2
To the Operator
as unsorted municipal waste. The user is
responsible for returning the unit to the appropriate
collection facility, as specified by your local code.
The unit you have purchased has been carefully
engineered and manufactured to give you
dependable operation. This unit, when properly
operated and cared for, will produce a consistent
quality product. Like all mechanical products, it will
require cleaning and maintenance. A minimum
amount of care and attention is necessary if the
operating procedures outlined in this manual are
followed closely.
For additional information regarding applicable local
disposal laws, please contact the municipal waste
facility and/or local authorized Taylor distributor.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this unit are
warranted for the term stated in the Limited
Warranty section in this manual. However, due to
the Montreal Protocol and the U.S. Clean Air Act
Amendments of 1990, many new refrigerants are
being tested and developed, thus seeking their way
into the service industry. Some of these new
refrigerants are being advertised as drop-in
replacements for numerous applications. It should
be noted that in the event of ordinary service to this
unit's refrigeration system, only the refrigerant
specified on the affixed data label should be
used. The unauthorized use of alternate refrigerants
will void your Taylor compressor warranty. It is the
unit owner's responsibility to make this fact known to
any technician he employs.
This Operator's Manual should be read before
operating or performing any maintenance on the
unit.
Your Taylor unit will NOT compensate for and/or
correct any errors made during the set-up or filling
operations. Thus, the initial assembly, set-up, and
priming procedures are of extreme importance. It is
strongly recommended that all personnel
responsible for the unit's operation, including
assembly and disassembly, go through these
procedures together in order to be properly trained
and to make sure that all understand their role in
using and maintaining the unit.
In the event you should require technical assistance,
please contact your local authorized Taylor
Distributor.
It should also be noted that Taylor does not warrant
the refrigerant used in its equipment. For example, if
the refrigerant is lost during the course of ordinary
service to this unit, Taylor has no obligation to either
supply or provide replacement refrigerant either at
billable or unbillable terms. Taylor will recommend a
suitable replacement if the original refrigerant is
banned, obsoleted, or no longer available during the
five (5) year Taylor warranty of the compressor.
Note: Your Taylor warranty is valid only if the parts
are authorized Taylor parts, purchased from the
local authorized Taylor Distributor, and only if all
required service work is provided by an authorized
Taylor service technician. Taylor reserves the right
to deny warranty claims on units or parts if
non-Taylor approved parts or incorrect refrigerant
were installed in the unit, system modifications were
performed beyond factory recommendations, or it is
determined that the failure was caused by abuse,
misuse, neglect, or failure to follow all operating
instructions. For full details of your Taylor Warranty,
please see the Limited Warranty section in this
manual.
From time-to-time Taylor may test new refrigerant
alternates. Should a new refrigerant alternate prove,
through Taylor's testing, that it would be accepted as
a drop-in replacement for this unit, then the
disclaimer in this “Compressor Warranty Disclaimer”
section will not apply to the use of the alternate
refrigerant approved by Taylor.
To find out the current status of an alternate
refrigerant as it relates to your compressor warranty,
call Taylor or your local authorized Taylor distributor.
Be prepared to provide the Model/Serial Number of
the unit in question.
If the crossed out wheeled bin symbol is
affixed to this unit, it signifies that this unit is
compliant with the EU Directives as well as other
similar end of life legislation in effect after August
13, 2005. Therefore, it must be collected separately
after its use is completed, and cannot be disposed
Note: Continuing research results in steady
improvements; therefore, information in this
Operator Manual is subject to change without
notice.
131220
To the Operator
4
Model 8756
Section 3
Safety
We, at Taylor Company, are concerned about the
safety of the operator at all times when they are
coming in contact with the unit and its parts. Taylor
makes every effort to design and manufacture
built-in safety features to protect both operators and
service technicians.
S
S
Installing and servicing refrigeration equipment can
be hazardous due to system pressure and electrical
components. Only trained and qualified service
personnel should install, repair, or service
refrigeration equipment. When working on
refrigeration equipment, observe precautions noted
in the literature, tags and labels attached to the unit,
and other safety precautions that may apply. Follow
all safety code requirements. Wear safety glasses
and work gloves.
S
S
S
S
IMPORTANT - Failure to adhere to the
following safety precautions may result in
severe personal injury or death. Failure to
comply with these warnings may also damage
the unit and/or its components. Such damage
may result in component replacement and
service repair expenses.
S
DO NOT operate the unit without reading
this entire Operator Manual first. Failure to follow all
of these operating instructions may result in damage
to the unit, poor performance, health hazards,
personal injury, or death.
S
This unit is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge.
Where limited equipment operation is allowed for
public use, such as a self-serve application,
supervision or instruction concerning the use of the
appliance by a person responsible for their safety is
required. Children should be supervised to ensure
that they do not play with the appliance.
All repairs should be performed by an
authorized Taylor service technician.
The main power supplies to the unit must be
disconnected prior to performing installation,
repairs, or maintenance.
DO NOT operate the unit unless it is
properly grounded.
DO NOT operate the unit with larger fuses
than specified on the unit's data label.
Cord Connected Units: Only Taylor
authorized service technicians or licensed
electricians may install a plug or
replacement cord on these units.
Units that are permanently connected to
fixed wiring and for which leakage currents
may exceed 10 mA, particularly when
disconnected or not used for long periods,
or during initial installation, shall have
protective devices such as a GFI, to protect
against the leakage of current, installed by
the authorized personnel to the local codes.
Stationary units which are not equipped with
a power cord and a plug or another device
to disconnect the appliance from the power
source must have an all­pole disconnecting
device with a contact gap of at least 3 mm
installed in the external installation.
Supply cords used with this unit shall be
oil­resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer­sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.
131220
Model 8756
5
Safety
DO NOT use a water jet to clean or rinse
the unit. Failure to follow these instructions may
result in serious electrical shock.
S
DO NOT allow untrained personnel to
operate this unit.
S
DO NOT operate the unit unless all service
panels and access doors are restrained with
screws.
Access to the service area of the unit must
be restricted to persons having knowledge and
practical experience with the unit, in particular as far
as safety and hygiene are concerned.
Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to
the cleaning section of this Operator Manual for the
proper procedure to clean this unit.
S
This unit is designed to maintain product
temperature under 41°F (5°C). Any product being
added to this unit must be below 41°F (5°C). Failure
to follow this instruction may result in health hazards
and poor freezer performance.
DO NOT remove any internal operating
parts (including, but not limited to, freezer
door, beater, or scraper blades), unless all
control switches are in the OFF position.
Failure to follow these instructions may result in
severe personal injury, especially to fingers or
hands, from hazardous moving parts.
DO NOT run the unit without product. Failure to
follow this instruction can result in damage to the
unit.
DO NOT obstruct air intake and discharge
openings:
This unit has many sharp edges that can
cause severe injuries.
S
DO NOT put objects or fingers in the door
spout. This may contaminate the product
and cause severe personal injury from blade
contact.
S
USE EXTREME CAUTION when removing
the beater assembly. The scraper blades
are very sharp.
Air cooled units require a minimum of 3” (76 mm) of
clearance around all sides of the freezer and 12”
(305 mm) on top to allow for adequate air flow
across the condenser(s). Failure to allow adequate
clearance can reduce the refrigeration capacity of
the freezer and possibly cause permanent damage
to the compressor.
For Indoor Use Only: This unit is designed to
operate indoors, under normal ambient
temperatures of 70°­75°F (21°­24°C). The unit has
successfully performed in high ambient
temperatures of up to 104°F (40°C) at reduced
capacities.
This unit must be placed on a level surface.
Extreme care should be taken when moving the unit
for any reason. Two or more persons are required to
safely move this unit. Failure to comply may result in
personal injury or damage to the unit.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of
1.0 meter from the surface of the unit and at a
height of 1.6 meters from the floor.
131220
Safety
6
Model 8756
Notes:
Model 8756
7
Safety
Section 4
Operator Parts Identification
Figure 1
160701
Operator Parts Identification
8
Model 8756
8756 Parts Identification
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
PANEL A.-FRONT
X22879
16
COVER-MIX TANK
024590
2
STUD-NOSE CONE
068410
17
FUNNEL-MIX
036637
3
BOLT-CARRIAGE
012347
18
TRAY-DRIP 22-7/8 X 5-1/8
014533
4
PANEL A.-LOWER SIDE (R & L)
X23956
19
SHIELD-SPLASH 23” LONG
022766
5
PANEL-UPPER SIDE LEFT
028599
20
COVER-LEFT MIX STORAGE
037138
6
HOOD
048526
21
COVER-RIGHT MIX STORAGE
037139
7
PANEL-UPPER REAR
022015
22
TRIM-CORNER-LEFT/RIGHT
022013
8
PANEL-LOWER REAR
023598
23
TRIM A.-SIDE LEFT/RIGHT
X22424
9
PANEL-UPPER SIDE RIGHT
028600
24
TRIM A.-SHELF
X24813
10
PAN-DRIP 17-1/4” LONG
027504
25
TRIM-FRONT-LEFT
024824-SP
11
CASTER-SWIVEL 3/4-10 3” WHL
021279
26
TRIM-FRONT-RIGHT
024825
12
GASKET-CABINET MIX DOOR
024629
27
TRIM-BOTTOM CABINET
024826
13
PROBE A.-MIX (2)
X35981
28
STRIP-TOP TRIM
024827
14
BOOT-MIX COVER
037200
29
CASTER 3” SWIVEL (FRONT)
030307
15
TANK A.-MIX W/DECALS
X38755
30
SCREW-6-32 X 3/8 SLOTTED
002201
15a*
TANK (ONLY)
034928
Model 8756
*NOT SHOWN
9
Operator Parts Identification
Beater Door Assembly
Figure 2
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
HANDLE A.-DRAW ADJ
X55096
7
BEATER A.-3.4QT-1 PIN
X46231
1a
HANDLE-ADJUSTABLE
028804
8
SHAFT-BEATER
032564
1b
SCREW-ADJUSTMENT
055092
9
SEAL-DRIVE SHAFT
032560
1c
O-RING-1/4 OD X .070W 50
015872
10
BLADE-SCRAPER-PLASTIC
084350
1d
NUT-5/16-24 FINISHED HEX
029639-BLK
11
O-RING-5/16 OD X .070W
016272
2
ROD A.-PIVOT-SHORT
X22388
12
ROD A.-PIVOT-LONG
X22387
3
O-RING-3/8 OD X .070W
016137
13
DOOR A.-3 SPOUT
X51532-12
4
PLUG-PRIME
028805
14
O-RING-7/8 OD X .103W
014402
5
GASKET-DOOR HT 4"-DOUBLE
048926
15
CAP-DESIGN-1.010"ID-6 POINT
014218
6
KIT A.-BEATER-FRONT SHOES
X50350
16
VALVE A.-DRAW
X18303
6a
SHOE-FRONT HELIX-REAR
050346
17
NUT-STUD-SHORT
034383
6b
BEARING-FRONT-SHOE
050348
18
NUT-STUD-LONG
034382
6c
SHOE-FRONT HELIX-FRONT
050347
160701
Operator Parts Identification
10
Model 8756
Air/Mix Pump Assembly
ITEM
DESCRIPTION
PART NO.
1
CAP-PUMP
021276-9
2
PIN-RETAINING
021276-8
*3
PUMP A.-SOFT SERVE
COMPLETE
X22345
3a
CYLINDER A.-PUMP
022345-1
3b
PIN-RETAINING
021276-8
3c
PISTON
021276-2
3d
RING-CHECK 2” OD x 1/2
020050
3e
O-RING 2-1/8 OD x .139 W
020051
3f
BODY A.-VALVE
X22345-3
3g
O-RING - 13/16 OD x .139 W
021278
3h
ELBOW-INLET 90 DEGREE
022502-4
4
ORIFICE
023425-50
5
O-RING - 3/8 OD x .070 W
016137
6
LINE A.-FLARE
038299
7
LINE A.-PUMP PRESSUSRE
X27139
8
DIAPHRAGM-PRESSURE
SWITCH
020249
9
TUBE-VINYL 5/8 ID X 1/8 WALL
020945-18
10
COUNTERWEIGHT-SUCTION
TUBE
020452
*INCLUDES ITEMS 3a-3h
Figure 3
Model 8756
11
Operator Parts Identification
Accessories
Figure 4
ITEM
DESCRIPTION
PART NO.
ITEM
1
BRUSH-MIX PUMP BODY
023316
7
2
BRUSH-PRESSURE SWITCH
027647
3
BRUSH SET-LVB
050103
4
BRUSH-FEED TUBE
021101
5
BRUSH-DOUBLE ENDED
013072
6
BRUSH-REAR BEARING
013071
DESCRIPTION
PART NO.
BRUSH-DRAW VALVE
013073
*8
SANITIZER-STERA SHEEN
GREEN
SEE NOTE
9
LUBRICANT-TAYLOR 4 OZ.
047518
10
KIT A.-TUNE UP
X49463-2
11
PAIL-10 QT.
013163
*Note: A sample container of sanitizer is sent with the
unit. For reorders, order Stera Sheen part no. 055492
(100 packs) or Kay-5 part no. 041082 (125 packs).
140814
Operator Parts Identification
12
Model 8756
Section 5
Important: To the Operator
Figure 5
ITEM
1
2
3
4
5
DESCRIPTION
POWER SWITCH (TOGGLE)
RESET SWITCH
MIX REFRIGERATION CONTROL
STANDBY KEY
WASH KEY
Model 8756
ITEM
6
7
8
9
13
DESCRIPTION
AUTO KEY
PUMP KEY
MIX LOW INDICATOR
MIX OUT INDICATOR
Important: To the Operator
Symbol Definitions
Reset Button
To better communicate in the International arena,
the words on many of our operator switches and
buttons have symbols to indicate their functions.
Your Taylor equipment is designed with these
International symbols.
The reset button is located in the decorative plate
above the SOFTECH controls. The reset protects
the beater motor from an overload condition. Should
an overload occur, the reset mechanism will trip. To
properly reset the freezer, press the AUTO key to
cancel the cycle. Turn the power switch to the OFF
position. Press the reset button firmly. Turn the
power switch to the ON position. Press the WASH
key and observe the freezer's performance. The
beater motor should be turning the drive shaft in a
clockwise (from operator end) direction without
binding.
= AUTO
= ON
= OFF
= WASH
If it is turning properly, press the WASH key to
cancel the cycle. Press the AUTO key on both sides
to resume normal operation. If the freezer shuts
down again, contact a service technician.
= PUMP
MIX REF
= MIX REF
When the MIX REF key is pressed, the light comes
on, indicating the mix cabinet refrigeration system is
operating. There are two touch-tone panels, one for
each freezing cylinder. The mix refrigeration system
is controlled by the MIX REF key found on the left
panel. By pressing the AUTO key on either side of
the freezer, the MIX REF function is automatically
turned on. The MIX REF function cannot be
cancelled unless the AUTO or STANDBY mode is
cancelled first.
= STANDBY
= MIX LOW
= MIX OUT
Power Switch
When placed in the ON position, the power switch
allows SOFTECH control panel operation.
Standby
Indicator Lights MIX LOW and MIX OUT
During long “No Sale” periods it becomes necessary
to warm the product in the freezing cylinder to
approximately 35_ to 40_F (1.7_to 4.4_C) to prevent
overbeating and product breakdown.
When the STANDBY key is pressed, the light comes
on, indicating the CTR (Cylinder Temperature
Retention System) has been activated. In the
STANDBY mode, the WASH, PUMP, and AUTO
functions are automatically cancelled. The MIX REF
function is automatically locked in to maintain the
mix in the cabinet.
When the MIX LOW light begins to flash, the mix
tank has a low supply of mix and should be refilled
as soon as possible. When the MIX OUT light
begins to flash, it indicates the mix tank has been
almost completely exhausted and has an insufficient
supply of mix to operate the freezer. At this time, the
STANDBY and AUTO modes are locked out and the
freezer shuts down. To initiate the refrigeration
system, add mix to the tank and press the AUTO
key. The freezer will automatically begin operation.
Important: To the Operator
To resume normal operation, press the AUTO key.
When the unit cycles off, the product in the freezing
cylinder will be at serving viscosity.
14
Model 8756
Wash
Adjustable Draw Handle
When the WASH key is pressed, the light comes on,
indicating beater motor operation. The STANDBY or
AUTO modes must be cancelled first to activate the
WASH mode.
This unit features an adjustable draw handle to
provide the best portion control, giving a better,
consistent quality to your product and controlling
costs. The draw handle should be adjusted to
provide a flow rate of 5 to 7-1/2 oz. of product by
weight per 10 seconds. To increase the flow rate,
turn the screw counterclockwise. To decrease the
flow rate, turn the screw clockwise.
Auto
When the AUTO key is pressed, the light comes on,
indicating the main refrigeration system has been
activated. In the AUTO mode, the WASH or
STANDBY functions are automatically cancelled.
The MIX REF function is automatically locked in to
maintain the mix in the cabinet and the PUMP
function is locked in to allow air/mix pump operation
as required.
In addition, for purposes of sanitizing and rinsing,
the flow rate can be increased by removing the pivot
pin and placing the restrictive bar on the top.
When drawing product, always have the restrictive
bar on the bottom.
Pump
IMPORTANT! When dispensing product, pull
only one draw handle at a time.
When the PUMP key is pressed, the light comes on
indicating the air/mix pump will operate as required.
Note: An indicating light and an audible tone will
sound whenever a mode of operation has been
pressed. To cancel any function, press the key
again and the light and mode of operation will shut
off.
Model 8756
15
Important: To the Operator
Section 6
Operating Procedures
The Model 8756 has two freezing cylinders. The size
of each freezing cylinder is 3.4 quarts (3.2 liters).
Mix is stored in the lower front refrigerated
compartment and is pumped up to the freezing
cylinder by an air/mix pump.
Duplicate the following procedures, where they
apply, for the second freezing cylinder.
We begin our instructions at the point where we
enter the store in the morning and find the parts laid
out to air dry from the previous night's brush
cleaning.
If you are disassembling the machine for the first
time, or need information to get to this starting point
in our instructions, turn to page 31, “Disassembly”
and start there.
Figure 6
Note: For ease of cleaning, the seal may be turned
inside out. Be sure to position the seal correctly
during assembly.
Assembly
MAKE SURE THE POWER SWITCH IS IN
THE “OFF” POSITION. Failure to follow this
instruction may result in electrocution or injury to
fingers or hands from hazardous moving parts.
Step 1
Lubricate the groove and shaft portion that comes in
contact with the bearing on the beater drive shaft.
Slide the seal over the shaft and groove until it
snaps into place. DO NOT lubricate the hex end of
the drive shaft. Fill the inside portion of the seal
with1/4” more lubricant and evenly lubricate the end
of the seal that fits onto the rear shell bearing.
Operating Procedures
Figure 7
16
Model 8756
Step 2
Install the drive shaft through the rear shell bearing
in the freezing cylinder and engage the hex end
firmly into the gear box coupling. Be sure the drive
shaft fits into the drive coupling without binding.
Step 4
If the blades are in good condition, place the rear
scraper blade over the rear holding pin on the
beater. The hole on the scraper blade must fit
securely over the pin to prevent costly damage.
Figure 10
Figure 8
Note: Scraper blades should be replaced every 3
months.
USE EXTREME CAUTION when handling
the beater assembly. The scraper blades are very
sharp and may cause injury.
Step 5
Holding the rear blade on the beater, slide it into the
freezing cylinder half way. Install the front scraper
blade over the front holding pin.
Step 3
Before installing the beater assembly, check the
scraper blades for any signs of wear or damage. If a
scraper blade is nicked or worn, replace both
blades.
Figure 11
Step 6
Before installing the beater shoes, check the shoes
for any nicks, cracks, or signs of wear. If any defects
are present, replace the beater shoes.
Figure 9
160701
Model 8756
17
Operating Procedures
Step 7
Install the beater shoes. Slide the beater assembly
the rest of the way into the freezing cylinder.
Step 10
Slide the white plastic front bearings over the baffle
rods. Make certain that the flanged end of the
bearing is resting against the freezer door. DO NOT
lubricate the gaskets or the front bearings.
Figure 12
Make sure the beater assembly is in position over
the drive shaft. Turn the beater slightly to be certain
that the beater is properly seated. When in position,
the beater will not protrude beyond the front of the
freezing cylinder.
Repeat these steps for the other side of the
freezer.
Figure 14
Step 8
Before assembling the freezer door, check the
following for any nicks, cracks, or signs of wear:
door bearings, door gaskets, draw valves, o-rings,
and all sides of the door assembly, including the
inside of the draw valve bores. Replace any
damaged parts.
Step 11
Slide the o-rings into the grooves on the prime
plugs. Apply an even coat of lubricant to the o-rings
and the shafts.
Step 9
Place the large rubber gaskets in the grooves on the
back side of the freezer door.
Figure 13
Figure 15
160701
Operating Procedures
18
Model 8756
Step 12
Insert the prime plugs into the holes at the top of the
freezer door and push down.
Figure 18
Step 15
Slide the two o-rings into the grooves on the draw
valves. Lubricate the o-rings.
Figure 16
Step 13
Insert the baffle rods through the beaters in the
freezing cylinders.
Figure 19
Step 16
Lubricate the inside of the freezer door spouts, top
and bottom. Insert the draw valves from the bottom
of the door until the slot in the draw valves comes
into view.
Figure 17
Step 14
With the door seated on the freezer studs, install the
short handscrews on the bottom and the long
handscrews on the top. Tighten the handscrews
equally in a criss-cross pattern until the door is snug.
Model 8756
Figure 20
19
Operating Procedures
Step 17
Slide the o-rings into the grooves on the pivot pins.
Lubricate the o-rings.
Figure 23
Step 20
Slide the rear drip pan into the hole in the side
panel.
Figure 21
Step 18
Slide the fork of each draw handle into the slot of the
draw valves, starting from the right. Slide the long
pivot pin through the right and middle draw handles.
Secure the left draw handle with the short pivot pin.
Figure 24
Step 21
Install the front drip tray and the splash shield
beneath the door spouts.
Figure 22
Note: This unit features adjustable draw handles to
provide the best portion control, giving a better
consistency quality to your product and controlling
costs. The draw handles can be adjusted for
different flow rates. See page 15 for more
information on adjusting these handles.
Step 19
Snap the design caps over the bottom of each door
spout.
Operating Procedures
Figure 25
20
Model 8756
Step 3
Slide the small o-ring into the groove in the air
orifice. DO NOT lubricate this o-ring.
Air/Mix Pump Assembly
This Model 8756 uses a single-stage pump. The
purpose of the pump is to transfer specific amounts
of air and mix to the freezing cylinder.
Step 1
Inspect the rubber and plastic pump parts. These
parts must be in 100% good condition for the pump
and entire machine to operate properly. They cannot
properly serve their intended function if nicks, cuts,
or holes in the material are present.
Inspect the plastic pumps parts for cracks, wear,
and de-lamination of plastic. Replace any defective
parts immediately and discard the old.
Figure 28
Step 2
Assemble the piston by sliding the check band and
the o-ring into the grooves on the piston. Do not
lubricate the check band or o-ring.
Step 4
Check the small hole in the air orifice to insure that it
is not clogged. Place the air orifice into the top of the
piston.
Figure 26
Figure 29
Note: A concave shaped check band indicates an
incorrect assembly. Turn the check band inside out
to correctly expose the flat surface.
Step 5
Lightly lubricate the inside of the pump body, top
and bottom.
Figure 27
Figure 30
150423
Model 8756
21
Operating Procedures
Step 6
Insert the piston, air orifice end first, into the pump
body and push upward.
Step 8
Insert the liquid valve body by aligning the steel
button at the base of the liquid valve body with the
cut-out groove at the bottom of the pump body.
Figure 31
Figure 34
Note: The drive hole in the piston must be visible
through the hole in the pump body.
Step 9
Slide the o-ring into the groove on the mix inlet fitting
and lubricate the o-ring.
Figure 32
Figure 35
Step 7
Slide the two check bands and the two o-rings into
the grooves on the liquid valve body. Do not
lubricate the check bands or o-rings.
Step 10
Insert the mix inlet fitting into the hole in the base of
the liquid valve body.
Figure 33
Operating Procedures
Figure 36
22
Model 8756
Step 11
Secure the pump parts in position by sliding the
keeper pin through the holes located at the bottom
of the pump body.
Step 13
To secure the air/mix pump, place the pump collar
over the pump body. (The cross holes of the pump
collar will be on top.)
Figure 39
Figure 37
Align the drive hole in the piston to the ball crank of
the motor reducer. At the same time, align the
locating pin on the face plate.
Step 12
Assemble the flare line and suction line. Attach the
suction line to the barbed end of the mix inlet fitting
and allow the weighted end to hang freely.
Slide the pump collar upward into the grooves on the
side of the face plate and secure the air/mix pump in
place by slipping the keeper pin through the cross
holes of the pump collar.
Attach one end of the flare line to the threaded fitting
on the lower side of the pump body. Allow the other
end to hang freely.
Note: Alignment of the air/mix pump is extremely
important. Severe and costly damage may occur if it
is not properly aligned.
Figure 38
Model 8756
Figure 40
23
Operating Procedures
Step 14
Lubricate both sides of the pressure switch
diaphragm.
Sanitizing
Step 1
Prepare a pail of approved 100 PPM sanitizing solu­
tion (examples: 2-1/2 gal. [9.5 liters] of Kay-5 or
2 gal. [7.6 liters] of Stera-Sheen). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS.
Step 2
Place the pail of sanitizing solution inside the mix
cabinet.
Step 3
Brush clean the mix inlet tube with the long brush
and the sanitizing solution.
Figure 41
Step 15
Place diaphragm into groove in pressure switch cap.
Figure 44
Figure 42
Step 4
Connect the free end of the flare line to the threaded
fitting on the mix inlet tube.
Step 16
Screw the cap securely onto the housing.
Figure 43
Repeat these steps for other side of freezer.
Operating Procedures
Figure 45
24
Model 8756
Step 5
Attach the quick disconnect fitting of the pressure
line to the other fitting on the mix inlet tube, just
above the flare line. Allow the other end to hang
free.
Figure 48
Step 9
Drain the pressure line. Connect the free end of the
pressure line to the pressure switch.
Figure 46
Step 6
Insert the free end of the suction line and the
pressure line into the pail of sanitizing solution.
Figure 49
Step 10
Place an empty pail beneath the door spout. Raise
the prime plug.
Figure 47
Step 7
Place the power switch in the ON position.
Step 8
Press the PUMP key. A light will illuminate,
indicating that the air/mix pump is operating. This
action will cause the sanitizing solution to be
pumped through the air/mix pump and out through
the pressure line. After approximately 15 seconds,
press the PUMP key. The light will extinguish and
the pump will stop operation.
Model 8756
Figure 50
25
Operating Procedures
Step 11
Press the WASH and PUMP keys. The indicator
lights will illuminate, indicating pump and beater
motor operation.
Figure 53
Step 14
When the sanitizer stops flowing from the door
spout, close the draw valve. Press the WASH and
PUMP keys to stop operation.
Figure 51
Step 12
When a steady stream of sanitizing solution is
flowing from the prime plug hole in the bottom of the
freezer door, press the PUMP key. This will
de-activate pump operation. Push down the prime
plug and allow the beater to agitate for 5 minutes.
Figure 54
Step 15
Disconnect the pressure line from the pressure
switch. Drain the sanitizer. Reconnect the pressure
line to the pressure switch.
Repeat these steps for the second freezing
cylinder.
Step 16
Prepare a sink with an approved sanitizing solution
(examples: Stera Sheen or Kay-5). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS.
Figure 52
Step 13
After 5 minutes, open the prime plug. Press the
PUMP key. Open the draw valve and draw off the
remaining sanitizer. Momentarily open the center
draw handle to sanitize the center door spout.
Operating Procedures
Step 17
Take the following parts to the sink and sanitize:
mix tanks, mix tank covers, mix probes, mix storage
covers, and funnels.
26
Model 8756
Step 4
Install the funnel. Fill the mix tank with fresh mix.
Priming
Step 1
Place the mix tank and the cover in the mix cabinet.
Step 2
Insert the prongs of the mix probe inside the mix
tank. Connect the mix probe in the socket
receptacle.
Figure 57
Step 5
Remove the funnel and install the mix storage cover.
Close the mix cabinet door.
Step 6
Place an empty pail beneath the door spout and
open the draw valve. With the prime plug still in the
UP position, press the PUMP key. This will allow the
mix to be pumped through the freezing cylinder and
force out any remaining sanitizer. When full strength
mix is flowing from the door spout, close the draw
valve.
Figure 55
Step 3
Place the free end of the suction line into the mix
tank.
Figure 56
Model 8756
Figure 58
27
Operating Procedures
Step 7
When a steady stream of mix is flowing from the
prime plug hole in the bottom of the freezer door,
press the PUMP key to stop operation.
Figure 61
Repeat these steps for the other side of the
freezer.
Figure 59
Step 8
Once the stream of mix stops flowing from the prime
plug hole, push down the prime plug. Rinse the
prime plug hole area with water. Remove the pail
and discard the mix and sanitizer.
When the unit cycles off, the product will be at the
correct viscosity.
Note: Keep the mix cabinet door closed except
when filling the mix tank and during cleaning and
sanitizing procedures. Leaving the door open while
the mix refrigeration system is active may cause the
evaporator to ice up and impair the mix cabinet
refrigeration.
Closing Procedure
Figure 60
Step 9
Press the AUTO key. The MIX REF indicator will
illuminate to indicate the mix refrigeration system is
operating. The AUTO indicator will illuminate to
indicate that the main refrigeration system is
operating. The PUMP indicator will illuminate to
indicate that the air/mix pump will operate whenever
mix is needed in the freezing cylinder.
Operating Procedures
To disassemble the Model 8756, the following items
will be needed:
28
Two cleaning and sanitizing pails
Necessary brushes (provided with freezer)
Cleaner
Single service towels
Model 8756
Draining Product From the
Freezing Cylinder
Rinsing
Step 1
Fill the empty pail in the mix cabinet with two gallons
(7.6 liters) of cool, clean water. Place the free end
of the suction line in the pail of water.
Step 1
Press the AUTO and MIX REF keys to cancel
freezer operation.
Step 2
Disconnect the pressure line from the pressure
switch and place it in the pail of water.
Step 2
Open the mix cabinet door and remove the mix
storage cover, the mix tank cover, the mix tank, and
the mix probe.
Step 3
Press the PUMP key. This action will cause the
rinse water to be pumped through the air/mix pump
and out through the pressure line. After
approximately 15 seconds, press the PUMP key to
stop operation.
Step 3
If local health codes permit the use of rerun,
empty the mix from the mix tank into a sanitized,
NSF approved stainless steel rerun container. Place
a sanitized lid on the rerun container and place it in
the walk-in cooler.
Note: If local health codes DO NOT permit the
use of rerun, the product must be discarded.
Step 4
Place the suction line in an empty pail in the mix
cabinet.
Repeat these steps for the second freezing
cylinder.
Figure 62
Step 4
Drain and connect the free end of the pressure line
to the pressure switch.
ALWAYS FOLLOW LOCAL HEALTH CODES.
Model 8756
29
Operating Procedures
Step 5
Place an empty pail beneath the door spout. Raise
the prime plug and press the WASH and PUMP
keys.
Cleaning
Step 1
Prepare a pail of approved 100 PPM cleaning solu­
tion (examples: 2-1/2 gal. [9.5 liters] of Kay-5 or
2 gal. [7.6 liters] of Stera-Sheen). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS.
Step 2
Place the pail of cleaning solution inside the mix
cabinet and insert the suction line.
Figure 63
Step 6
When a steady stream of rinse water is flowing from
the prime plug hole in the bottom of the freezer door,
open the draw valve and drain all the rinse water.
Step 7
Once the rinse water stops flowing from the door
spout, close the draw valve and press the WASH
and PUMP keys to stop operation.
Figure 65
Step 3
Disconnect the pressure line from the pressure
switch and place it in the pail of cleaning solution.
Step 4
Press the PUMP key. This action will cause the
cleaning solution to be pumped through the air/mix
pump and out through the pressure line. After
approximately 15 seconds, press the PUMP key to
stop operation.
Figure 64
Step 8
Disconnect the pressure line from the pressure
switch. Drain the water and then reconnect.
Step 9
Repeat this procedure using clean warm water, until
the water being discharged is clear.
Figure 66
Step 5
Drain and connect the free end of the pressure line
to the pressure switch.
Repeat these steps for the second freezing
cylinder.
Operating Procedures
30
Model 8756
Step 6
Place an empty pail beneath the door spout. Raise
the prime plug and press the WASH and PUMP
keys.
Step 9
Place the power switch in the OFF position before
disassembling the machine.
Figure 69
Figure 67
Disassembly
Step 7
When a steady stream of solution is flowing from the
prime plug hole in the bottom of the freezer door,
open the draw valve and draw off the remaining
cleaning solution.
MAKE SURE THE POWER SWITCH IS IN
THE “OFF” POSITION. Failure to follow this
instruction may result in electrocution or injury to
fingers or hands from hazardous moving parts.
Step 8
Once the solution stops flowing from the door spout,
close the draw valve and press the WASH and
PUMP keys to stop operation.
Step 1
Remove the handscrews, freezer door, beaters,
shoes, scraper blades and the drive shafts from the
freezing cylinders. Take these parts to the sink for
cleaning.
Step 2
Remove the air/mix pump. Unscrew the flare line
from the mix inlet tube. Disengage the pressure line
from the pressure switch and the mix inlet tube. Pull
the retaining pin out of the pump collar and slide the
collar down. Tilt the air/mix pump away from the
machine and take the entire assembly to the sink for
further disassembly and brush cleaning.
Step 3
Remove the pressure switch cap from the mix
cabinet. Remove the diaphragm from the cap.
Repeat Steps 3 and 4 for the other side of the
freezer.
Figure 68
Repeat these steps for the other side of the
freezer.
Model 8756
Step 4
Remove the front drip tray and the splash shield.
31
Operating Procedures
Step 5
Return to the freezer with a small amount of
cleaning solution. Use the black bristle brush to
brush clean the rear shell bearings at the back of the
freezing cylinders.
Brush Cleaning
Step 1
Prepare a sink with an approved cleaning solution
(examples: Kay-5 or Stera-Sheen). USE
WARM WATER AND FOLLOW THE
MANUFACTURER'S SPECIFICATIONS.
If an approved cleaner other than Kay-5 or
Stera-Sheen is used, dilute it according to the label
instructions. IMPORTANT: Follow the label
directions. Too STRONG of a solution can cause
parts damage and too MILD of a solution will not
provide adequate cleaning. Make sure all brushes
provided with the freezer are available for brush
cleaning.
Figure 70
Step 2
Remove the seals from the drive shafts.
Step 6
Using the long, flexible brush and cleaning solution,
clean the mix inlet tubes located in the mix cabinet.
Thoroughly clean the tubes all the way up to the
freezing cylinder. This area needs special attention
because bacteria and milkstone can build up here.
Step 3
From the freezer doors, remove the gaskets, front
bearings, pivot pins, draw handles, draw valves,
prime plugs, and design caps. Remove all o-rings.
Step 7
Remove the rear drip pan from the side panel and
take it to the sink for cleaning.
Note: To remove the o-rings, use a single service
towel to grasp the o-ring. Apply pressure in an
upward direction until the o-ring pops out of its
groove. With the other hand, push the top of the
o-ring forward. It will roll out of the groove and can
be easily removed. If there is more than one o-ring
to be removed, always remove the rear o-ring first.
This will allow the o-ring to slide over the forward
rings without falling into the open grooves.
Note: If the rear drip pan is filled with an excessive
amount of mix, refer to the Troubleshooting Guide.
Step 8
Thoroughly brush clean all disassembled parts in the
cleaning solution. Make sure all lubricant and mix
film is removed. Take particular care to brush clean
the draw valve cores in the freezer door.
Step 4
Remove the flare lines, the suction lines, the
retaining pins and the mix inlet fittings from the
pump cylinders. Remove the liquid valve bodies
from the pump cylinders.
Step 9
Place the parts on a clean, dry surface to air dry
overnight.
Step 10
Wipe clean all exterior surfaces of the freezer and
the mix cabinet.
Remove the pistons from the pump cylinders.
Remove all o-rings and check bands.
Operating Procedures
32
Model 8756
Section 7
Important: Operator Checklist
j 5. Properly prepare the cleaning and sanitizing
solutions. Read and follow the label directions
carefully. Too strong of a solution may
damage the parts and too weak of a solution
will not do an adequate job of cleaning or
sanitizing. Sanitize the freezing cylinder for 5
minutes.
During Cleaning and Sanitizing
ALWAYS FOLLOW LOCAL HEALTH CODES.
Cleaning and sanitizing schedules are governed
by federal, state, or local regulatory agencies,
and must be followed accordingly. If the unit
has a “Standby mode”, it must not be used in
lieu of proper cleaning and sanitizing
procedures and frequencies set forth by the
ruling health authority. The following check
points should be stressed during the cleaning
and sanitizing operations.
j 6. The temperature of the mix in the mix cabinet
and the walk-in cooler should be below 38_F
(3.3_C).
Regular Maintenance Checks
j 1. Replace scraper blades that are bent,
damaged or worn.
CLEANING AND SANITIZING MUST BE
PERFORMED DAILY.
j 2. Before installing the beater, be certain that the
scraper blades are properly attached over the
pins and the beater assembly is straight.
Troubleshooting Bacterial Count
j 1. Thoroughly clean and sanitize the machine
regularly, including complete disassembly and
brush cleaning.
j 3. Check the rear shell bearing for signs of wear
(excessive mix leakage in the rear drip pan)
and be certain it is properly cleaned.
j 2. Use all brushes supplied for thorough
cleaning. The brushes are specially designed
to reach all mix passageways.
j 4. Using a screwdriver and cloth towel, keep the
rear shell bearing and the female hex drive
socket clean and free of lubricant and mix
deposits.
j 3. Use the long white bristle brush to clean the
mix feed tube which extends from the mix
reservoir to the rear of the freezing cylinder.
j 5. Dispose of o-rings and seals if they are worn,
torn, or fit too loosely, and replace with new
ones.
j 4. Use the black bristle brush to thoroughly
clean the rear shell bearing located at the rear
of the freezing cylinder. Be sure there is a
generous amount of cleaning solution on the
brush.
Model 8756
j 6. Follow all lubricating procedures as outlined in
“Assembly”.
33
Important: Operator Checklist
j 7. If your machine is air cooled, check the
condensers for accumulation of dirt and lint.
Dirty condensers will reduce the efficiency
and capacity of the machine. Condensers
should be cleaned monthly with a soft brush.
Never use screwdrivers or other metal probes
to clean between the fins.
Note: For machines equipped with an air
filter, it will be necessary to vacuum the filters
on a monthly schedule.
The Air/Mix Pump
j 1. Dispose of the o-rings, the check bands and
the pressure switch diaphragm if they are
worn, torn or fit too loosely. Replace them
with new ones.
j 2. Follow lubricating procedures carefully.
Never lubricate check bands.
j 8. Your machine is equipped with an auxiliary
refrigeration system. Check the auxiliary
condenser for accumulation of dirt and lint.
Dirty condensers will reduce the refrigeration
capacity of the mix cabinet. Condensers must
be cleaned monthly with a soft brush. Never
use screwdrivers or other metal probes to
clean between the fins.
j 3. Handle plastic pump parts with care to avoid
nicks and cracks.
j 4. Be sure the pressure line is securely attached
to the pressure switch.
j 5. Clean, sanitize, and lubricate the pressure
switch diaphragm daily.
j 9. On water cooled units, check the water lines
for kinks or leaks. Kinks can occur when the
machine is moved back and forth for cleaning
or maintenance purposes.
Important: Operator Checklist
j 6. Be sure the air/mix pump is properly aligned
with the face plate of the motor reducer or
severe and costly damage may occur.
34
Model 8756
Section 8
PROBLEM
1. No product is being
dispensed.
Troubleshooting Guide
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Low on mix. The MIX
OUT light is on.
a. Add mix to the mix tank
and press the AUTO key.
27
b. The power switch is in the
OFF position.
b. Place the power switch in
the ON position and press
the AUTO key.
---
c. The beater motor is out on
reset.
c. Reset the freezer.
d. Insufficient mix in the
freezing cylinder.
d. Refer to problem #2.
---
e. Restriction in the door
spout.
e. Disassemble and clean
the freezer. Never put
objects or fingers in the
door spout.
---
f. Machine is unplugged.
f. Plug machine into the wall
receptacle.
---
g. Circuit breaker is off or the
fuse is blown.
g. Turn the breaker on or
replace the fuse.
---
h. The mix probe was not
installed properly or was
damaged.
h. Check the mix probe
installation.
i. The beater assembly is
rotating counterclockwise.
2. Insufficient mix in the
freezing cylinder.
Model 8756
13
27
i. Contact a service
technician to correct the
rotation to clockwise.
---
a. Suction line is not fully
submerged in the mix.
a. Arrange the suction line
so the weighted end is
fully submerged.
27
b. Improper seal of suction
line to the mix inlet fitting.
b. Remove the suction line
from the mix inlet fitting.
Place under hot running
water, allow tubing to
swell, then cool. Connect
suction line to barbed
fitting. Eventual
replacement will be
necessary.
---
c. Worn or defective check
bands or o-rings in air/mix
pump assembly.
c. Replace regularly. Never
lubricate check bands.
21 / 40
35
Troubleshooting Guide
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
2. Insufficient mix in the
freezing cylinder. (Cont'd.)
d. Missing, defective, or no
lubrication on the mix inlet
fitting o-ring.
d. Replace or evenly
lubricate the o-ring on the
mix inlet fitting.
22 / 40
e. The pump motor is not
activated.
e. Place power switch in
OFF position. Push reset
button on pump drive
motor. Return power
switch to ON position.
Press the AUTO key.
---
f. Pressure switch
diaphragm installed
incorrectly, or missing.
f. Diaphragm must be
correctly installed in the
pressure switch cap.
24
g. The mix inlet tube is
frozen or clogged.
g. Use the long flexible brush
and sanitizing solution to
clear the restriction in the
mix inlet tube. Contact a
service technician to
correct the cause of
over-refrigeration in the
mix cabinet.
---
h. The mix pump ball crank
is broken.
h. Contact a service
technician to replace the
ball crank.
---
i. Defective air/mix pump
pressure switch.
i. Contact a service
technician to replace the
pressure switch.
---
3. Product is too stiff.
Troubleshooting Guide
a. Insufficient mix in the
freezing cylinder.
a. Refer to problem #2.
b. Improper priming
procedures.
b. Drain the freezing cylinder
and reprime the machine.
c. Out-of-date mix.
c. Use fresh mix.
d. Viscosity control is set too
cold.
d. Contact a service
technician.
36
27
27/ 40
---
Model 8756
PROBLEM
4. Product is too soft.
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Worn scraper blades.
a. Replace scraper blades
regularly.
40
b. Dirty condensers or air
filters on air cooled units.
b. Clean monthly.
34
c. Inadequate water supply
on water cooled units.
c. Check the water supply.
Check water lines for
leaks or kinks.
1/ 34
d. Inadequate air space
around air cooled units.
d. Allow adequate room for
air flow across the
condensers. Minimum of
3” (76 mm) clearance on
all sides. Do not obstruct
air discharge on top. 12”
(305 mm) clearance on
top of freezer.
1
e. Viscosity control is set too
warm.
e. Contact a service
technician.
a. Warm mix was placed in
the tank.
a. Mix added to the mix tank
should be below 40_F
(4.4_C).
33
b. The mix cabinet door was
left open.
b. The door must be kept
closed.
27
c. The mix cabinet door
gasket is not sealing.
c. Repair or replace gasket.
d. Dirty mix cabinet
condenser or air filter.
d. Clean monthly.
e. The mix cabinet
refrigeration system needs
adjustment.
e. Contact a service
technician.
---
6. Mix in the mix cabinet is
too cold.
a. The mix cabinet
refrigeration system needs
adjustment.
a. Contact a service
technician.
---
7. Excessive mix leakage
from the bottom of the
door spout.
a. Worn, missing or incorrect
o-ring is on the draw
valve.
b. Check the o-rings.
(Replace every 3 months.)
40
b. Improper lubrication on
the draw valve o-rings.
c. Lubricate properly.
19
5. Mix in the mix cabinet is
too warm.
Model 8756
37
---
--34
Troubleshooting Guide
PROBLEM
8. Excessive mix leakage
into the rear drip pan.
9. The drive shaft is stuck in
the gear box coupling.
10. Freezing cylinder walls are
scored.
11. The air/mix pump does
not operate.
Troubleshooting Guide
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Worn or missing drive
shaft seal.
a. Install or replace the seal.
16/ 40
b. Improper lubrication of the
drive shaft.
b. Lubricate properly.
c. Worn rear shell bearing.
c. Contact a service
technician to replace the
rear shell bearing.
---
d. The gear box is out of
alignment.
d. Contact a service
technician to align the
gear box.
---
a. Rounded corners on hex
end of drive shaft or gear
coupling.
a. Replace damaged
component.
---
b. The gear box is out of
alignment.
b. Contact a service
technician to align the
gear box.
---
a. Broken pins on beater
assembly.
a. Repair or replace the
beater assembly. Be sure
the scraper blades are
properly seated on pins.
17
b. Missing front bearing.
b. Install the front bearing on
the back of the freezer
door.
18
c. The beater assembly is
bent.
c. Repair or replace the
beater assembly. Contact
a service technician to
correct the cause of
insufficient mix in freezing
cylinder.
---
a. The pump motor is not
activated.
a. Place power switch in
OFF position. Push reset
button on pump drive
motor. Place power switch
in ON position.
---
b. The pressure switch
diaphragm was installed
incorrectly or is missing.
b. The diaphragm must be
correctly installed in the
pressure switch cap.
24
c. Defective air/mix pump
pressure switch.
c. Contact a service
technician to replace the
pressure switch.
---
38
16
Model 8756
PROBLEM
REMEDY
PAGE
REF.
a. The machine is
unplugged.
a. Plug the machine into the
wall receptacle.
---
b. The circuit breaker is off
or the fuse is blown.
b. Turn the breaker on or
replace the fuse.
---
c. Low on mix. The MIX
OUT light is flashing.
c. Add mix to the mix tank
and press the AUTO key.
13
d. The mix probe is not
installed properly or is
damaged.
d. Check the mix probe
installation.
27
e. The beater motor is out on
reset.
e. Reset the freezer.
13
f. The power switch is in the
OFF position.
f. Place the power switch in
the ON position.
25
g. The unit is off on high
head pressure.
g. Air cooled: clean the
condenser.
Water cooled: check the
water supply. Contact a
service technician.
34
13. Overrun is too low.
a. The air orifice is plugged.
a. Use a soap solution to
clean the small hole in the
air orifice.
---
14 Air is “popping” during the
dispensing of product.
a. Incorrect assembly of the
air/mix pump.
a. Assemble and lubricate
the air/mix pump
components according to
instructions.
21
b. The mix suction line is
losing its prime.
b. The mix suction line is
cracked or has a loose fit
to the mix inlet fitting.
Replace the mix suction
line.
---
12. The machine will not
operate in the AUTO
mode.
Model 8756
PROBABLE CAUSE
39
Troubleshooting Guide
Section 9
PART DESCRIPTION
Parts Replacement Schedule
EVERY 3 MONTHS
EVERY 6 MONTHS
ANNUALLY
Black Bristle Brush, 1” x 2”
Inspect & Replace
if Necessary
Minimum
Double Ended Brush
Inspect & Replace
if Necessary
Minimum
White Bristle Brush, 1” x 2”
Inspect & Replace
if Necessary
Minimum
White Bristle Brush, 9/16” x 44”
Inspect & Replace
if Necessary
Minimum
White Bristle Brush, 3” x 7”
Inspect & Replace
if Necessary
Minimum
Small White Bristle Brush, 1/8”
Inspect & Replace
if Necessary
Minimum
Brush Set
Inspect & Replace
if Necessary
Minimum
Scraper Blades
X
Drive Shaft Seal
X
Freezer Door Gasket
X
Front Bearing
X
Beater Shoes
X
Draw Valve O-Rings
X
Prime Plug O-Rings
X
Air/Mix Pump O-Rings
X
Check Rings
X
Mix Inlet Fitting O-Ring
X
Pressure Switch Diaphragm
X
Design Cap
X
Parts Replacement Schedule
40
Model 8756
Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company is pleased to provide this limited warranty on new Taylor­branded freezer equipment available
from Taylor to the market generally (the “Product”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re-manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty
for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
Product
Part
Limited Warranty Period
Soft Serve
Frozen Yogurt
Shakes
Smoothies
Insulated shell assembly
Five (5) years
Refrigeration compressor
(except service valve)
Five (5) years
Beater motors
Two (2) years
Frozen Beverage
Batch Desserts
Beater drive gear
Two (2) years
Printed circuit boards and
Softech controls beginning
with serial number H8024200
Two (2) years
Parts not otherwise listed in
this table or excluded below
One (1) year
LIMITED WARRANTY CONDITIONS
1.
If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.
2.
This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.
3.
Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
4.
Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5.
The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
131220
Model 8756
41
Limited Warranty on Equipment
2.
Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.
3.
Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4.
External hoses, electrical power supplies, and machine grounding.
5.
Parts not supplied or designated by Taylor, or damages resulting from their use.
6.
Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7.
Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8.
Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9.
Any Product purchased over the Internet.
10.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11.
Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12.
Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13.
Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14.
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
Limited Warranty on Equipment
42
Model 8756
750 N. Blackhawk Blvd.
Rockton, IL 61072, USA
Model 8756
43
Limited Warranty on Equipment
Section 11
Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company is pleased to provide this limited warranty on new Taylor genuine replacement components and
parts available from Taylor to the market generally (the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re-manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
Part's Warranty Class Code or Part
Limited Warranty Period
Class 103 Parts¹
Three (3) months
Class 212 Parts²
Twelve (12) months
Class 512 Parts
Twelve (12) months
Class 000 Parts
No warranty
Taylor Part #072454 (Motor-24VDC *C832/C842*)
Four (4) years
LIMITED WARRANTY CONDITIONS
1.
If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.
2.
This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.
3.
The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4.
Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
5.
Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6.
This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.
7.
The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.
1, 2
Except that Taylor Part #032129SER2 (Compressor­Air­230V SERV) and Taylor Part #075506SER1
(Compressor­Air­115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131220
Limited Warranty on Parts
44
Model 8756
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2.
Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.
3.
Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build­up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.
4.
Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.
5.
Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.
6.
External hoses, electrical power supplies, and machine grounding.
7.
Parts not supplied or designated by Taylor, or damages resulting from their use.
8.
Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9.
Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10.
Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11.
Any Part purchased over the Internet.
12.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13.
Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14.
Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15.
Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16.
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
Model 8756
45
Limited Warranty on Parts
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072, USA
Limited Warranty on Parts
46
Model 8756
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising