Taylor | Model C043 | Owner Manual | Taylor Model C043 User manual

Taylor Model C043 User manual
OPERATOR’S 
MANUAL
Model C043
Frozen Custard Machine
Original Operating Instructions
068359-M
7/22/10 (Original Publication)
(Updated 11/28/2018)
Complete this page for quick reference when service is required:
Taylor Distributor: __________________________________________________________
Address:_________________________________________________________________
Phone: __________________________________________________________________
Fax: ____________________________________________________________________
E-mail: __________________________________________________________________
Service: _________________________________________________________________
Parts: ___________________________________________________________________
Date of Installation: ________________________________________________________
Information found on the data label:
Model Number: ___________________________________________________________
Serial Number: ____________________________________________________________
Electrical Specs:
Voltage__________________ Cycle____________________
Phase____________________________________________
Maximum Fuse Size: ______________________________________________________ A
Minimum Wire Ampacity: ___________________________________________________ A
© 2010 Taylor Company
(Updated 11/28/2018)
068359-M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be
a violation of Copyright Law of the United States of America and other countries, could result in the awarding of
Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal
penalties.
All rights reserved.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1: To the Installer
Installer Safety ........................................................................................................1-1
Site Preparation ......................................................................................................1-1
Air-Cooled Machines...............................................................................................1-2
Water Connections..................................................................................................1-2
Electrical Connections.............................................................................................1-2
Beater Rotation .......................................................................................................1-3
Refrigerant ..............................................................................................................1-3
Section 2: To the Operator
Section 3: Safety
Section 4: Operator Parts Identification
C043 Exploded View...............................................................................................4-1
Beater Door and Hopper Assemblies......................................................................4-3
Accessories.............................................................................................................4-5
Section 5: User Interface
Hopper Refrigeration Switch ...................................................................................5-1
Operational Refrigeration Switch ............................................................................5-1
Flow Adjustment Knob ............................................................................................5-1
Mix Low Indicator Light ...........................................................................................5-1
Beater Motor Switch................................................................................................5-1
Digital Countdown Timer.........................................................................................5-1
Section 6: Operating Procedures
Assembly.................................................................................................................6-1
Sanitizing.................................................................................................................6-4
Priming ....................................................................................................................6-6
Hold Cycle During Operation ..................................................................................6-8
Resuming Production During Operation .................................................................6-9
Preparing for Shutdown .........................................................................................6-10
Rinsing ...................................................................................................................6-11
Cleaning .................................................................................................................6-13
Disassembly...........................................................................................................6-14
Brush Cleaning.......................................................................................................6-15
068359-M
i
Section 7: Operator Checklist
During Cleaning and Sanitizing .............................................................................. 7-1
Troubleshooting Bacterial Count ............................................................................ 7-1
Regular Maintenance Checks ................................................................................ 7-1
Winter Storage ....................................................................................................... 7-2
Section 8: Troubleshooting Guide
Section 9: Parts Replacement Schedule
Section 10: Limited Warranty on Equipment
Section 11: Limited Warranty on Parts
ii
068359-M
To the Installer
Section 1
The following information has been included in the
manual as safety and regulatory guidelines. For complete
installation instructions, please see the Installation
Checklist.
Installer Safety
!
IMPORTANT! In all areas of the world, the
machine should be installed in accordance with existing
local codes. Please contact your local authorities if you
have any questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and service
of Taylor machines.
• Only authorized Taylor service personnel should
perform installation and repairs on the machine.
• Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the industry
standards on lockout/tagout procedures before
beginning any installation or repairs.
• Authorized service personnel must ensure that
the proper personal protective equipment (PPE)
is available and worn when required during
installation and service.
• Authorized service personnel must remove all
metal jewelry, rings, and watches before
working on electrical equipment.
DANGER! The main power supply(s) to the
machine must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts, as well as poor performance or
damage to the machine.
Note: All repairs must be performed by a Taylor service
technician.
Site Preparation
Review the area where the machine will be installed
before uncrating the machine. Make sure that all possible
hazards to the user and the machine have been
addressed.
!
WARNING! Only install this machine in a
location where its use and maintenance is restricted to
trained personnel. Failure to comply may result in
personal injury.
For Indoor Use Only: This machine is designed to
operate indoors under normal ambient temperatures of 
70°F to 75°F (21°C to 24C). The machine has
successfully performed in high ambient temperatures of
104°F (40°C) at reduced capacities.
WARNING! This machine must NOT be
installed in an area where a water jet or hose can be
used. NEVER use a water jet or hose to rinse or clean
the machine. Failure to follow this instruction may result
in electrocution.
CAUTION! This machine must be installed on
a level surface to avoid the hazard of tipping. Extreme
care should be taken in moving this machine for any
reason. Two or more persons are required to safely move
this machine. Failure to comply may result in personal
injury or machine damage.
WARNING! This machine has many sharp
edges that can cause severe injuries.
To the Installer
068359-M
1-1
1
TO THE INSTALLER
Air-Cooled Machines
Do not obstruct air intake and discharge openings.
1
C043: A minimum air clearance of 3 in. (76 mm) is
required on the left side and rear of the machine, and 
0.0 in. on the right side. The drip tray can be installed on
either side. That side requires 36 in. (914 mm) to allow
for installation and removal of drip tray. Allow 36 in. (914
mm) at the rear of the machine for service access.
Each air-cooled C043 requires three RC35 remote
condensing systems.
RC35: Each 60 Hz remote condenser requires a
minimum air clearance of 6 in. (152 mm) on three sides.
Each 50 Hz remote condenser requires a minimum air
clearance of 12 in. (305 mm) on three sides.
An air deflector must be installed on the condenser side
of each RC35 if the floor clearance is less than 5 in. 
(127 mm).
Note: The legs are typically mounted on 4 in. x 4 in.
lumber to achieve the minimum floor clearance.
Failure to allow adequate air clearance can reduce the
refrigeration capacity of the machine and possibly cause
permanent damage to the compressor.
Water Connections
Water-Cooled Machines Only
An adequate cold water supply must be provided with a
hand shutoff valve. On the underside rear of the base
pan, two 3/8 in. IPS water connections for inlet and outlet
have been provided for easy hookup. Water lines
connected to the machine should have 1/2 in. inside
diameters. (Flexible lines are recommended, if local
codes permit.) Depending on local water conditions, it
may be advisable to install a water strainer to prevent
foreign substances from clogging the automatic water
valve. There will be only one water-in and one water-out
connection. Do not install a hand shutoff valve on the
water-out line! Water should always flow in this order:
first, through the automatic water valve; second, through
the condenser; and third, through the outlet fitting to an
open trap drain.
Minimum water pressure is 30 psi (207 kPa) and
maximum water pressure is 150 psi (1034 kPa).
1-2
068359-M
C043: The minimum air clearance requirement is 3 in.
(76 mm) on both sides and at the rear of the machine.
The drip tray can be installed on either side. That side
requires 36 in. (914 mm) to allow for the installation and
removal of the drip tray. Allow 36 in. (914 mm) at the rear
of the machine for service access.
!
IMPORTANT! A backflow prevention device is
required on the incoming water connection side. Please
see the applicable national, state, and local codes for
determining the proper configuration.
Electrical Connections
Each machine requires one power supply for each data
label on the machine. Check the data label(s) on the
machine for branch circuit overcurrent protection or fuse,
circuit ampacity, and other electrical specifications. See
the wiring diagram provided inside the electrical box for
proper power connections.
In the United States, this machine is intended to be
installed in accordance with the National Electrical Code
(NEC) ANSI/NFPA 70-1987. The purpose of the NEC
code is the practical safeguarding of persons and
property from hazards arising from the use of electricity.
This code contains provisions considered necessary for
safety. Compliance therewith and proper maintenance
will result in an installation essentially free from hazard!
In all other areas of the world, machines should be
installed in accordance with the existing local codes.
Please contact your local authorities.
!
FOLLOW YOUR LOCAL ELECTRICAL CODES.
WARNING! This machine must be properly
grounded! Failure to do so can result in severe personal
injury from electrical shock!
To the Installer
TO THE INSTALLER
IMPORTANT! This machine is provided with
an equipotential grounding lug that is to be properly
attached to the rear of the frame by the authorized
installer. The installation location is marked by the
equipotential bonding symbol (5021 of IEC 60417-1) on
the removable panel and the machine’s frame.
!
•
•
•
•
To the Installer
068359-M
NOTICE!
Stationary machines which are not equipped
with a power cord and a plug or another device
to disconnect the machine from the power
source must have an all-pole disconnecting
device with a contact gap of at least 0.125 in.
(3 mm) installed in the external installation.
Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected
or not used for long periods, or during initial
installation, shall have protective devices to
protect against the leakage of current, such as a
GFI, installed by the authorized personnel to the
local codes.
Supply cords used with this machine shall be 
oil-resistant, sheathed flexible cable not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors
from abrasion.
If the supply cord is damaged, it must be
replaced by the manufacturer, service agent, or
a similarly qualified person, in order to avoid a
hazard.
1-3
1
TO THE INSTALLER
Beater Rotation
aware of government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory service department.
NOTICE! Beater rotation must be clockwise as
viewed looking into the freezing cylinder.
1
If the beater rotation is not counterclockwise, contact
your local authorized Taylor service technician.
Refrigerant
!
IMPORTANT! Refrigerants and their
associated lubricants may be extremely moisture
absorbent. When opening a refrigeration system, the
maximum time the system is open must not exceed
15 minutes. Cap all open tubing to prevent humid air or
water from being absorbed by the oil.
CAUTION! This machine contains fluorinated
greenhouse gases (F-Gas) to provide refrigeration using
a hermetically sealed circuit or within foam insulation.
This machine's type of gas, quantity, Global Warming
Potential (GWP), and CO2 tonnes equivalent information
is recorded on the unit's data-label. The refrigerant used
is generally considered non-toxic and non-flammable.
However any gas under pressure is potentially
hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with liquid.
Filling the cylinder to approximately 80% will allow for
normal expansion.
!
CAUTION! Use only approved refrigerant
listed on the machine's data-label or authorized through a
manufacturer's technical bulletin. The use of any other
refrigerant may expose users and operators to
unexpected safety hazards.
WARNING! Refrigerant liquid sprayed onto the
skin may cause serious damage to tissue. Keep eyes
and skin protected. If refrigerant burns should occur,
flush the area immediately with cold water. If burns are
severe, apply ice packs and contact a physician
immediately.
NOTICE! Taylor reminds technicians to be
1-4
068359-M
To the Installer
To the Operator
Section 2
The machine you have purchased has been carefully
engineered and manufactured to give you dependable
operation. The Taylor machine, when properly operated
and cared for, will produce a consistent quality product.
Like all mechanical products, this machine will require
cleaning and maintenance. A minimum amount of care
and attention is necessary if the operating procedures
outlined in this manual are followed closely.
IMPORTANT! This manual should be read
before operating or performing any maintenance on your
machine.
Your Taylor machine will not eventually compensate and
correct for any errors during the setup or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that all personnel responsible for the
machine’s operation review these procedures in order to
be properly trained and to make sure that there is no
confusion.
Note: Constant research results in steady
improvements; therefore, information in this manual is
subject to change without notice.
IMPORTANT! If the crossed-out waste
container symbol is affixed to this product, it signifies that
this product is compliant with the EU Directive as well as
other similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its use is
completed, and cannot be disposed as unsorted
municipal waste.
The user is responsible for delivering the product to the
appropriate collection facility, as specified by your local
code.
For additional information regarding applicable local
laws, please contact the municipal facility and/or local
authorized Taylor distributor.
In the event you should require technical assistance,
please contact your local authorized Taylor distributor.
Note: Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor distributor, and only if all required
service work is provided by an authorized Taylor service
technician. Taylor reserves the right to deny warranty
claims on machines or parts if unapproved Taylor parts or
incorrect refrigerant were installed in the machine,
system modifications were performed beyond factory
recommendations, or it is determined that the failure was
caused by abuse, misuse, neglect, or failure to follow all
operating instructions. For full details of your Taylor
warranty, please see the Limited Warranty section in this
manual.
To the Operator
Model C043
2-1
2
TO THE OPERATOR
Compressor Warranty Disclaimer
2
The refrigeration compressor(s) on this machine are
warranted for the term stated in the Limited Warranty
section in this manual. However, due to the Montreal
Protocol and the U.S. Clean Air Act Amendments of
1990, many new refrigerants are being tested and
developed, thus seeking their way into the service
industry. Some of these new refrigerants are being
advertised as drop-in replacements for numerous
applications. It should be noted that in the event of
ordinary service to this machine's refrigeration system,
only the refrigerant specified on the affixed data label
should be used. The unauthorized use of alternate
refrigerants will void your Taylor compressor warranty. It
is the machine owner's responsibility to make this fact
known to any technician he or she employs.
Taylor Company will continue to monitor the industry and
test new alternates as they are being developed. Should
a new alternate prove, through our testing, that it would
be accepted as a drop-in replacement, then the above
disclaimer would become null and void. To find the
current status of an alternate refrigerant as it relates to
your compressor warranty, call the local Taylor distributor
or the Taylor factory. Be prepared to provide the 
model/serial number of the machine in question.
It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
refrigerant is lost during the course of ordinary service to
this machine, Taylor has no obligation to either supply or
provide its replacement either at billable or non-billable
terms. Taylor does have the obligation to recommend a
suitable replacement if the original refrigerant is banned,
obsoleted, or no longer available during the five-year
warranty of the compressor.
2-2
Model C043
To the Operator
Safety
Section 3
We at Taylor Company are concerned about the safety of
the operator when he or she comes in contact with the
machine and its parts. Taylor has gone to extreme efforts
to design and manufacture built-in safety features to
protect both you and the service technician. As an
example, warning labels have been attached to the
machine to further point out safety precautions to the
operator.
!
DANGER! Failure to adhere to the following
safety precautions may result in severe personal injury or
death. Failure to comply with these warnings may also
damage the machine and/or its components. Such
damage may require component replacement and
service repair expenses.
IMPORTANT! This machine is provided with
an equipotential grounding lug that is to be properly
attached to the rear of the frame by the authorized
installer. The installation location is marked by the
equipotential bonding symbol (5021 of IEC 60417-1) on
the removable panel and the machine’s frame.
WARNING! DO NOT use a water jet to clean
or rinse the machine. Failure to follow these instructions
may result in serious electrical shock.
NOTICE! DO NOT operate the machine
without reading the Operator Manual. Failure to follow
this instruction may result in machine damage, poor
machine performance, health hazards, or personal injury.
•
•
•
!
•
IMPORTANT! This machine is to be used only
by trained personnel. It is not intended for use by children
or people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless
given supervision or instruction concerning the use of the
machine by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the machine.
WARNING! This machine must NOT be
installed in an area where a water jet or hose can be
used. NEVER use a water jet or hose to rinse or clean
the machine. Failure to follow this instruction may result
in electrocution.
Safety
Model C043
•
•
•
WARNING! Avoid injury.
DO NOT operate the machine unless it is
properly grounded.
DO NOT operate machine with larger fuses than
specified on the data label.
All repairs must be performed by an authorized
Taylor service technician.
The main power supplies to machine must be
disconnected prior to performing repairs.
For Cord-Connected Machines: Only
authorized Taylor service technicians or
licensed electricians may install a plug or
replacement cord on the machine.
Stationary machines which are not equipped
with a power cord and a plug or another device
to disconnect the machine from the power
source must have an all-pole disconnecting
device with a contact gap of at least 0.125 in.
(3 mm) installed in the external installation.
Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected
or not used for long periods, or during initial
installation, shall have protective devices to
protect against the leakage of current, such as a
3-1
3
SAFETY
•
•
3
GFI, installed by the authorized personnel to the
local codes.
Supply cords used with this machine shall be 
oil-resistant, sheathed flexible cable not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors
from abrasion.
If the supply cord is damaged, it must be
replaced by the manufacturer, service agent, or
a similarly qualified person, in order to avoid a
hazard.
!
WARNING! Only install this machine in a
location where its use and maintenance is restricted to
trained personnel. Failure to comply may result in
personal injury.
!
IMPORTANT! Access to the service area of
the machine is restricted to persons having knowledge
and practical experience with the machine, in particular
as far as safety and hygiene are concerned.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
distributor for service.
•
•
•
•
!
WARNING! Avoid injury.
DO NOT allow untrained personnel to operate
this machine.
DO NOT put objects or fingers in the door spout.
DO NOT operate the machine unless all service
panels and access doors are restrained with
screws.
DO NOT remove the machine door or beater
assembly unless the control switches are in the
OFF position.
Failure to follow these instructions may result in
contaminated product or severe personal injury to fingers
or hands from hazardous moving parts.
WARNING! This machine has many sharp
edges that can cause severe injuries.
Examples:
•Scraper blades
•Condenser fins
!
CAUTION! This machine is designed to
maintain product temperature under 41°F (5C). Any
product being added to this machine must be below 41F
(5C). Failure to follow this instruction may result in
health hazards and poor machine performance.
For Indoor Use Only: This machine is designed to
operate indoors, under normal ambient temperatures of 
70°F to 75°F (21°C to 24°C). The machine has
successfully performed in high ambient temperatures of
up to 104°F (40°C) at reduced capacities.
Do not run the machine without product. Failure to follow
this instruction can result in damage to the machine.
CAUTION! This machine must be placed on a
level surface. Failure to comply may result in personal
injury or machine damage.
3-2
NOTICE! Cleaning and sanitizing schedules
are governed by your federal, state, or local regulatory
agencies and must be followed accordingly. Please see
the cleaning section of this manual for the proper
procedure to clean this machine.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 
1.0 meter from the surface of the machine and at a height
of 1.6 meters from the floor.
Model C043
Safety
SAFETY
Minimum Air Clearances: Air-Cooled Machines
Minimum Air Clearances: Water-Cooled Machines
Do not obstruct air intake and discharge openings:
C043: The minimum air clearance requirement is 3 in.
(76 mm) on both sides and at the rear of the machine.
The drip tray can be installed on either side. That side
requires 36 in. (914 mm) to allow for the installation and
removal of the drip tray. Allow 36 in. (914 mm) at the rear
of the machine for service access.
C043: A minimum air clearance of 3 in. (76 mm) is
required on the left side and rear of the machine, and 0.0
in. on the right side. The drip tray can be installed on
either side. That side requires 36 in. (914 mm) to allow
for installation and removal of drip tray. Allow 36 in. (914
mm) at the rear of the machine for service access.
Failure to follow this instruction may cause poor machine
performance and damage to the machine.
Each air-cooled C043 requires three RC35 remote
condensing systems.
RC35 (used with air-cooled C043 machine only):
3
Each 60 Hz remote condenser requires a minimum air
clearance of 6 in. (152 mm) on three sides.
Each 50 Hz remote condenser requires a minimum air
clearance of 12 in. (305 mm) on three sides.
An air deflector must be installed on the condenser side
of each RC35 if the floor clearance is less than 5 in. (127
mm).
Note: The legs are typically mounted on 4 in. x 4 in.
lumber to achieve the minimum floor clearance.)
Failure to allow adequate air clearance can reduce the
refrigeration capacity of the machine and possibly cause
permanent damage to the compressor.
Safety
Model C043
3-3
SAFETY
Notes:
3
3-4
Model C043
Safety
Section 4
Operator Parts Identification
C043 Exploded View
4
Figure 4-1
Operator Parts Identification
Model C043
4-1
OPERATOR PARTS IDENTIFICATION
C043 Exploded View Parts Identification
Item
Description
Part No.
Item
Description
Part No.
1
Tray A.-Drip
X63636
9
Cover A.-Panel-Side
X65637
2
Cover-Hopper-Front INS
065701
10
Panel A.-Side Right
X63720
3
Cover-Hopper-Rear INS
065700
11
Leg-8" 2"OD-3/4-10 Stud-Hex
044652
4
Lever A.-Flow Reg
X66923
12
Nut-Stud
043666
5
Rod-Flow Control
063593
13
Handle-STNLS Flush Pull
019043
6
Tube A.-Feed Plastic
X67453
14
Chute-Long
063619
7
Panel A.-Rear
X63715
15
Chute-Short
063618
8
Screw-1/4-20X3/8 PHIL TRUSS
038872
16
Panel A.-Side Left
X63724
4
4-2
Model C043
Operator Parts Identification
OPERATOR PARTS IDENTIFICATION
Beater Door and Hopper Assemblies
4
Figure 4-2
Operator Parts Identification
Model C043
4-3
OPERATOR PARTS IDENTIFICATION
Beater Door and Hopper Assemblies Parts Identification
Item
Description
Part No.
Item
Description
Part No.
063618
9
Spring-Dasher Blade
063693
X63611-SER
10
Blade-Scraper-Rear
063640
1
Chute
2
Door Assembly
3
Nut-Stud
043666
11
Dasher A.-Custard
X83275
4
Plate-Draw Arm
063614
12
Seal-Drive Shaft
032560
5
Nut-Stud
034383
13
Tube A.-Feed Plastic
X67453
6
Gasket-Door HT 4IN-DBL
048926
14
Rod-Flow Control
063593
7
Bearing-Door-Front
064315
15
Chute-Long
063619
8
Blade-Scraper 30 Pitch
063656
4
4-4
Model C043
Operator Parts Identification
OPERATOR PARTS IDENTIFICATION
Accessories
4
Figure 4-3
Item
Description
Part No.
Item
Description
Part No.
1
Brush-Dbl End-Pump & Feed
013072
7
Tool-Dasher Shaft Remove
063623
2
Brush-Draw Valve 1”OD X 2”X17”
013073
*8
Sanitizer
3
Brush-Barrel
063843
9
Kit A.- Tune Up
X64743
4
Brush-Rear BRG.
063844
10
Rake-Blade Guard
064888
5
Brush-Mix Pump Body 3”X7”
023316
11
Timer-Countdown-Digital
065425
6
Brush-End-Door-Spout-SS
039719
12
Chute-Long
063619
See Note
*A sample of sanitizer is sent with the machine. For
reorders, order Stera Sheen® Part No. 055492 (100
packs) or Kay-5® Part No. 041082 (125 Packs).
Operator Parts Identification
Model C043
4-5
OPERATOR PARTS IDENTIFICATION
Notes:
4
4-6
Model C043
Operator Parts Identification
User Interface
Section 5
5
Figure 5-1
Item
Flow Adjustment Knob
Description
The flow adjustment knob adjusts the flow of product into
the freezing cylinders.
1
Hopper Refrigeration Switch
2
Operational Refrigeration Switch
3
Flow Adjustment Knob
4
MIX LOW Indicator Light
5
Beater Motor Switch
Mix Low Indicator Light
6
Digital Countdown Timer
Hopper Refrigeration Switch
When the mix low indicator light is illuminated, the mix
hopper has a low supply of mix and should be refilled as
soon as possible.
The hopper refrigeration switch activates the hopper
refrigeration.
Beater Motor Switch
Note: Whenever an adjustment is made, first turn the
adjustment knob all the way to 5 and then back to the
desired number.
The beater motor switch activates the beater motor.
Operational Refrigeration Switch
Place the operational refrigeration switch in the ON
position to allow the product to dispense. During no sale
periods, place the switch in the HOLD position to keep
the product refrigerated in the freezing cylinder.
User Interface
Digital Countdown Timer
The digital countdown timer is used to keep track of the
time needed to control product quality.
Model C043
5-1
USER INTERFACE
Notes:
5
5-2
Model C043
User Interface
Operating Procedures
Section 6
The Model C043 is a three-flavor custard machine. It has
three 30 qt. (28 L) hoppers. Mix flows by gravity through
an adjustable flow regulator into the freezing cylinders.
This machine has been designed to produce rich-tasting
custard product that can be drawn off and served from a
holding cabinet. The overrun is typically 20% to 25% and
varies depending on the mix formulation and the finished
product temperature 18°F to 21°F (-7.8°C to -6.1°C).
2. Place a bead of lubricant around the groove of the
beater shaft.
We begin our instructions at the point where we find the
parts disassembled and laid out to air-dry from the
previous brush cleaning.
The following procedures will show you how to assemble
the parts into the machine, sanitize them, and prime the
machine with fresh mix.
If you are disassembling the machine for the first time or
need information to get to this starting point in our
instructions, go to “Disassembly” on page 6-14 and start
there.
Figure 6-2
Note: When lubricating parts, use an approved food
grade lubricant (example: Taylor Lube).
3. Slide the seal over the shaft and groove until it snaps
into place.
Assembly
6
WARNING! Make sure the power switch is in
the OFF position! Failure to follow this instruction may
result in severe personal injury to fingers or hands from
hazardous moving parts.
Figure 6-3
Beater Shaft, Scraper Blade, and Feed Tube 
Assembly
1. Verify that the refrigeration switch and the beater
motor switch are both in the OFF position.
4. Fill the inside portion of the seal with 1/4 in. (6 mm)
more lubricant and lubricate the flat side of the seal
that fits onto the rear shell-bearing.
Figure 6-4
Figure 6-1
Operating Procedures
Model C043
6-1
OPERATING PROCEDURES
5. Lubricate the beater shaft.
8. Place a leaf spring and a short scraper blade on the
next set of pins.
Important! Do not lubricate the hex end of the
beater shaft.
9. Hold the two leaf springs and scraper blades in
place. Slide the beater shaft into the freezing cylinder
until the scraper blades are held in place by the
freezing cylinder. Rotate the beater shaft 
counterclockwise until the next set of pins is facing
up.
Figure 6-5
6. Inspect each scraper blade for any nicks or signs of
excessive wear. If any nicks or signs of wear are
present, replace the blade.
Figure 6-8
10. Place a leaf spring and a short scraper blade on the
next set of pins. Slide the beater shaft into the
freezing cylinder until the blade is held in place by the
freezing cylinder. Rotate the beater shaft
counterclockwise until the next set of pins is facing
up.
6
11. Continue adding leaf springs and short scraper
blades to the beater shaft until all 12 blades are
installed.
Figure 6-6
7. Starting at the hex end of the beater shaft, place a
metal leaf spring (arched upward) over the two pins
closest to that end. Install the long scraper blade on
top of the leaf spring.
Note: There is only one long scraper blade per
beater.
12. Slide the beater shaft into the freezing cylinder,
rotating the beater shaft slightly counterclockwise.
Engage the hex end firmly into the drive coupling at
the back of the machine. The square portion of the
beater shaft assembly should fit completely inside the
freezing cylinder. The bearing support pin will extend
beyond the freezing cylinder.
Note: It may be helpful to use the beater removal tool
to turn the beater while installing it.
Figure 6-7
6-2
Model C043
Operating Procedures
OPERATING PROCEDURES
2. Turn the door over and install the door gasket.
Note: Do not lubricate the gasket, as this will cause the
gasket to leak over time.
3. Press all around the gasket to ensure a flush, secure
fit in the groove. The gasket may have to be
stretched slightly to get it into the proper position.
To make sure that the gasket is correctly positioned,
verify that the middle section of the gasket is arched
upward. If the middle section of the gasket is 
concave, or extends into the middle of the seal, turn
the gasket over, as it is upside down.
Figure 6-9
Note: The drip pan is a convenient place to store the
beater removal tool.
13. Install the front bearing on the bearing support pin.
Figure 6-12
4. Seat the door on the freezer studs. To make sure the
door gasket doesn't fall off, hold the door flush with
the freezing cylinder with one hand while installing
the stud nuts with the other hand. Hand-tighten the
stud nuts equally in a crisscross pattern to make sure
the door is secured.
Figure 6-10
14. Repeat steps 1 to 13 on the remaining freezing
cylinders.
Door Assembly
1. With the door in a horizontal position, install the draw
arm plate. Install all three short stud nuts and leave
them loose.
Figure 6-13
5. Repeat steps 1 to 4 on the remaining freezing
cylinders.
Figure 6-11
Operating Procedures
Model C043
6-3
6
OPERATING PROCEDURES
Sanitizing
5. Attach the splash guards to the door studs.
1. Prepare an approved 100 PPM sanitizing solution
(examples: 5 gal. [19 L] of Kay- 5® or 4 gal. [15 L] of
Stera-Sheen®).
Important! Use warm water and follow the 
manufacturer’s specifications.
2. Place the feed tube and the flow control rod flat on
the bottom of the hopper.
Figure 6-17
6. Make sure the refrigeration switch and the hopper
refrigeration switch are in the OFF position.
Figure 6-14
3. Place the product chutes in the hopper.
6
Figure 6-18
Important! Refrigeration should not be on when water
is present in the freezing cylinder or hopper.
7. Place an empty pail under the draw arm plate (if the
machine is not equipped with a trough).
Figure 6-15
4. Make sure the draw arm plate is closed and the short
door stud nuts are secured.
.
Figure 6-19
8. Pour the sanitizing solution into the hopper.
Figure 6-16
6-4
Model C043
Operating Procedures
OPERATING PROCEDURES
Figure 6-23
Figure 6-20
Important! Your hands must be clean and sanitized
before proceeding with the next steps.
9. Brush clean the mix hopper.
13. Remove the splash guards from the doors.
Figure 6-21
10. Place the beater switch in the ON position and set
the timer for 5 minutes.
6
Figure 6-24
14. Remove the chute from the hopper.
Figure 6-22
Figure 6-25
11. After 5 minutes have elapsed, open the draw arm
plate and drain the sanitizer into the empty pail.
Note: If your machine is equipped with a trough, drain
the sanitizer into the trough.
15. Install the feed tube assembly into the mix inlet hole
located at the bottom of the hopper. Make sure the
feed-tube is completely seated in the mix inlet hole.
12. Place the beater switch in the OFF position and the
flow adjustment knob in the CLOSE position.
Operating Procedures
Model C043
6-5
OPERATING PROCEDURES
Note: The flow adjustment knob is used to adjust the
flow of mix. Turning the adjustment knob clockwise
increases the flow. A counterclockwise turn decreases
the flow. Adjust the mix flow as needed to maintain
proper product consistency.
2. On the front half of the hoppers, install the hopper
covers that have the raised lip.
Figure 6-26
16. Place one end of the flow control rod into the hole
located on the feed tube. Place the other end of the
rod into the hole on the front flow control lever.
Figure 6-29
3. Place the hopper refrigeration knob in the ON
position and set the timer for 30 minutes.
6
Figure 6-27
17. Discard the sanitizer.
18. Repeat steps 1 to 17 for the remaining freezing
cylinders.
Priming
1.
IMPORTANT: Verify that the flow adjustment knob is
in the CLOSE position and the beater motor switch is
in the OFF position. The draw arm plate must be
closed.
Figure 6-30
4. After 30 minutes have expired, fill the hopper with
fresh mix.
Note:
Use only fresh mix when priming the freezer.
5. On the back half of the hoppers, install the hopper
covers that have the concave lip. For maximum
capacity, the hopper should be full.
Figure 6-28
6-6
Model C043
Operating Procedures
OPERATING PROCEDURES
Figure 6-31
Figure 6-33
6. With the beater switch in the ON position and the
draw arm plate open, turn the flow control valve to 3
for 3 seconds to force out any residual water/
sanitizer.
10. After 3 minutes have expired, open the draw arm
plate. If the custard is too soft, close the draw arm
plate and wait 1 minute. Repeat until the custard
looks servable.
7. Once the water/sanitizer are purged out from the
barrel, close the draw arm plate.
Note: The first couple inches of custard will force out
any remaining sanitizing solution and should be
discarded.
8. Place the beater switch and the refrigeration switch in
the ON position. Set the timer for 1 minute.
Note: The refrigeration switch will not activate unless
the beater switch is on.
11. Close the draw arm plate. Using sanitized hands,
install a sanitized product chute.
6
Figure 6-34
Figure 6-32
12. Open the draw arm plate.
9. After 1 minute has expired, turn the flow adjustment
knob to 1 and set the timer for 3 minutes.
Note: Whenever an adjustment is made, first turn the
adjustment knob all the way to 5 and then back to the
desired number.
Figure 6-35
Operating Procedures
Model C043
6-7
OPERATING PROCEDURES
Note: A chattering noise indicates that not enough mix
is entering the freezing cylinder. It may be necessary to
increase the flow of mix into the freezing cylinder.
Increase the flow control knob only 1/2 a number at a
time. It takes 3 to 5 minutes to see the results of the
adjustment. (Whenever an adjustment is made, first turn
the adjustment knob all the way to 5 and then back to the
desired number.)
13. Continue to run the frozen custard into the holding
cabinet until the desired amount is obtained. Adjust
the mix flow as needed to maintain proper product
consistency. For maximum capacity, make sure the
hopper is full and the flow is adjusted as high as
possible within the acceptable product temperature
range.
6
2. After 1 minute has expired, place the refrigeration
switch in the HOLD position for custard.
Figure 6-38
3. When the frozen custard stops flowing
(approximately 2 minutes), place the beater motor
switch in the OFF position.
Figure 6-36
14. When the desired amount is obtained and more
custard will be made later, follow the “Hold Cycle
During Operation” instructions starting on page 6-8.
15. Repeat steps 1 to 14 for the remaining freezing
cylinders.
Figure 6-39
4. Use the rake to remove as much custard from the
product door as possible.
Hold Cycle During Operation
1. Place the flow adjustment knob in the CLOSE
position. Set the timer for 1 minute.
Figure 6-40
5. Close the draw arm plate. Make sure the left stud nut
is secured, and then the right stud nut.
Figure 6-37
6-8
Model C043
Operating Procedures
OPERATING PROCEDURES
Resuming Production During
Operation
1. Place the beater switch in the ON position.
Figure 6-41
6. Remove the custard chute and take it to the sink for
cleaning and sanitizing.
Figure 6-44
2. Place the refrigeration switch in the ON position.
Figure 6-42
6
7. Close the dipping cabinet cover.
8. Prepare a squeeze bottle of approved 100 PPM
sanitizing solution. Squeeze the sanitizing solution
around the draw arm plate and stud nuts to remove
any left-over product. If necessary, brush clean the
area with the door spout brush and rinse with the
sanitizing solution.
Figure 6-45
3. Set the timer for 1 minute. After the minute expires,
open the flow control assembly to 1 and set the timer
for 3 minutes.
Note: Whenever an adjustment is made, first turn the
adjustment knob all the way to 5 and then back to the
desired number.
Figure 6-43
9. Repeat steps 1 to 8 for the remaining freezing
cylinders.
Operating Procedures
Figure 6-46
Model C043
6-9
OPERATING PROCEDURES
4. After 3 minutes have expired, open the draw arm
plate. If the custard is too soft, close the draw arm
plate and wait 1 minute. Repeat as necessary.
7. Open the draw arm plate. Continue to run the frozen
custard into the holding cabinet until the desired
amount is obtained. Adjust the mix flow as needed to
maintain proper product consistency. When the
desired amount is obtained and more custard will be
made later, follow the “Hold Cycle During Operation”
instructions starting on page 6-8.
Figure 6-47
5. When custard appears, adjust the flow adjustment
knob to gain the desired custard texture. Turn the
flow adjustment knob clockwise if the product is too
firm and counterclockwise if the product is too soft.
Figure 6-50
Preparing for Shutdown
Perform the following procedures to remove the
remaining custard in the freezing cylinder when there is
mix in the hopper.
1. Place the refrigeration switch in the OFF position.
6
Figure 6-48
6. When the product looks servable, close the draw arm
plate. Using sanitized hands, install a sanitized
custard chute.
Figure 6-51
2. Set the timer for 20 minutes. This allows the freezing
cylinder enough time to warm before removing the
remaining custard.
3. Place the beater switch in the ON position.
Figure 6-49
6-10
Model C043
Operating Procedures
OPERATING PROCEDURES
6. After all the custard has drained from the hopper,
remove the hopper cover, the flow control rod, and
the feed tube.
Figure 6-52
4. Open the dipping cabinet cover. Close the draw arm
plate. Using sanitized hands, install a sanitized
custard chute.
Figure 6-55
7. Repeat steps 1 to 6 for the remaining freezing
cylinders.
Rinsing
1. Place the hopper refrigeration switch in the OFF
position.
6
Figure 6-53
5. Open the draw arm plate and turn the flow
adjustment knob to 5. Run the remaining mix through
the freezing cylinder and properly dispose of the mix.
Figure 6-56
2. Make sure the refrigeration switch is in the OFF
position.
Figure 6-54
Note: If local health codes permit the use of rerun,
place a sanitized, NSF-approved rerun container
beneath the opening of the front plate and run the
remaining mix into the container. See page 7-1 for
instructions regarding the proper use of rerun.
Operating Procedures
Figure 6-57
Model C043
6-11
OPERATING PROCEDURES
3. Close the draw arm plate and remove the product
chute.
6. With the brushes provided, scrub the mix hopper.
Figure 6-61
Figure 6-58
7. Place the beater switch in the ON position.
4. Install the splash guard.
Figure 6-62
6
Figure 6-59
5. With a pail beneath the draw arm plate, pour 4 gal.
(15 L) of cool, clean water into the hopper.
8. Open the draw plate and drain the rinse water from
the freezing cylinder.
Note: Use the faucet if the machine is equipped
with one.
Figure 6-63
9. Repeat this procedure until all mix residue is gone
and the water is clear.
Figure 6-60
6-12
10. Place the beater switch in the OFF position.
Model C043
Operating Procedures
OPERATING PROCEDURES
Figure 6-64
Figure 6-66
11. Repeat steps 1 to 10 for the remaining freezing
cylinders.
3. Using lukewarm water, prepare an approved 100
PPM sanitizing solution (examples: 5 gal. [19 L] of
Kay-5® or 4 gal. [15 L] of Stera-Sheen®).
Cleaning
Important! Failure to follow these cleaning procedures
may result in bacterial contamination of the frozen 
custard product.
!
Important! Use warm water and follow the 
manufacturer's specifications.
4. Pour the cleaning solution into the hopper. Brush
clean the sides and bottom of the hopper.
ALWAYS FOLLOW LOCAL HEALTH CODES.
1. Make sure the refrigeration switch is in the OFF
position.
6
Figure 6-67
5. Place the beater switch in the ON position. Set the
timer for 5 minutes.
Figure 6-65
2. Close the draw arm plate.
Figure 6-68
6. After 5 minutes has elapsed, open the draw arm plate
and drain all the solution from the freezing cylinder.
Operating Procedures
Model C043
6-13
OPERATING PROCEDURES
2. Disassemble the door assembly. Remove the gasket
from the product door.
Figure 6-69
7. Place the beater switch in the OFF position.
Figure 6-71
3. Remove the front bearing from the door or beater
shaft.
8. Repeat steps1 to 7 for each freezing cylinder.
6
Disassembly
Figure 6-72
WARNING! Make sure the power switch is in
the OFF position. Failure to follow this instruction may
result in severe personal injury from hazardous moving
parts.
4. While removing the beater shaft, take each blade and
leaf spring off and place them in a container for
cleaning.
1. Remove the door assembly.
Figure 6-73
5. Remove the rear seal from the beater shaft. Use a
single-use towel to remove the lubricant from the seal
before taking it to the sink for cleaning.
Figure 6-70
6-14
Model C043
Operating Procedures
OPERATING PROCEDURES
Brush Cleaning
Important! Failure to follow these cleaning procedures
may result in bacterial contamination of the frozen 
custard product.
!
ALWAYS FOLLOW LOCAL HEALTH CODES.
1. Prepare a sink with an approved cleaning solution
(examples: Kay-5® or Stera-Sheen®).
Figure 6-74
Important! Use warm water and follow the 
manufacturer's specifications.
Note: If the rear seal remains in the drive coupling at
the back of the machine, instead of coming out with the
beater shaft, perform the following:
•
Reinstall three blades and leaf springs on the
beater shaft.
•
Slide the beater shaft back into the freezing 
cylinder until the hex end is firmly engaged in
the drive coupling.
•
Remove the beater shaft by pulling it straight
out.
•
Repeat as necessary until the rear seal is
removed.
If another approved cleaner is used, dilute it 
according to the label instructions.
Important! Follow the label directions. Too strong
of a solution can cause parts damage, while too mild
of a solution will not provide adequate cleaning.
6. Remove the hopper covers, the feed tube, and the
flow control rod.
6
Figure 6-76
Make sure all brushes provided with the freezer are
available for brush cleaning.
2. Thoroughly brush clean all disassembled parts in the
cleaning solution, making sure all lubricant and mix
film is removed.
Figure 6-75
7. Take all the parts to the sink for complete
disassembly and brush cleaning.
8. Repeat steps 1 to 7 for each freezing cylinder.
Figure 6-77
Operating Procedures
Model C043
6-15
OPERATING PROCEDURES
3. Use the double-ended brush to clean the inside of
the feed tubes.
6. Using the long, white brush, brush clean each
freezing cylinder.
Figure 6-81
Figure 6-78
4. Return to the freezer with a small amount of cleaning
solution. Using the draw valve brush 
(1 in. x 2 in. x 17 in.), brush clean the mix inlet hole in
each mix hopper.
7. Prepare a sink with an approved sanitizing solution
(examples: Kay-5® or Stera-Sheen®).
Important! Use warm water and follow the 
manufacturer's specifications.
6
Figure 6-82
Figure 6-79
5. Using the brush with the long black tip, brush clean
the rear-shell bearing at the back of each freezing
cylinder.
8. Repeat step 2 using the sanitizing solution.
9. Place all cleaned parts on a clean, dry surface to 
air-dry overnight.
10. Empty, clean, and reinstall the rear drip pan.
Figure 6-80
Figure 6-83
11. Wipe clean all exterior surfaces of the machine with a
clean, sanitized towel.
6-16
Model C043
Operating Procedures
Operator Checklist
Section 7
During Cleaning and Sanitizing
!

On a designated day of the week, run the mix as
low as feasible and discard it after closing. This
will break the rerun cycle and reduce the
possibility of high bacteria and coliform counts.

Properly prepare the cleaning and sanitizing
solutions. Read and follow the label directions
carefully. Too strong of a solution may damage
the parts and too weak of a solution will not do an
adequate job of cleaning or sanitizing.

The temperature of the mix in the mix hopper and
walk-in cooler should be below 40°F (4.4°C).
ALWAYS FOLLOW LOCAL HEALTH CODES.
Cleaning and sanitizing schedules are governed by
federal, state, or local regulatory agencies, and must be
followed accordingly. If the machine has a Standby mode,
it must not be used instead of proper cleaning and
sanitizing procedures and frequencies set forth by the
ruling health authority. The following checkpoints should
be stressed during the cleaning and sanitizing
operations.
Regular Maintenance Checks

Replace scraper blades that are nicked or
damaged. Before installing the beater assembly,
make sure the scraper blades are properly
attached to the beater shaft.

Thoroughly clean and sanitize the machine
regularly, including complete disassembly and
brush cleaning.
Check the rear-shell bearing for signs of wear
(excessive mix leakage in rear drip pan) and make
sure it is properly cleaned.

Use all brushes supplied for thorough cleaning.
The brushes are specially designed to reach all
mix passageways.
Using a long brush and a cloth towel, keep the
rear-shell bearing and the female hex drive socket
clean and free of lubricant and mix deposits.

Dispose of O-rings and seals if they are worn,
torn, or fit too loosely, and replace with new ones.

Follow all lubricating procedures as outlined in
“Assembly” on page 6-1.

If your machine is air-cooled, check the condenser
for dirt and lint accumulation. Dirty condensers will
reduce the efficiency and capacity of the machine.
Condensers should be cleaned monthly with a
soft brush. Never use screwdrivers or other metal
probes to clean between the fins.
!
IMPORTANT! Cleaning and sanitizing must be
performed daily.
Troubleshooting Bacterial Count



Use the white bristle brush to clean the mix inlet
hole which extends from the mix hopper down to
the rear of the freezing cylinder.

Use the black bristle brush to thoroughly clean the
rear shell bearing located at the rear of the
freezing cylinder. Use a generous amount of
cleaning solution on the brush.

IF LOCAL HEALTH CODES PERMIT THE USE
OF RERUN, make sure the mix rerun is stored in
a sanitized, covered stainless-steel container and
used the following day. Do not prime the machine
with rerun. When using rerun, skim off the foam
and discard. Mix the rerun with fresh mix in a ratio
of 50:50 during the day’s operation.
Operator Checklist
Model C043
Note: For machines equipped with an air filter, it will
be necessary to vacuum the filters monthly.
WARNING! Always disconnect electrical
7-1
7
OPERATOR CHECKLIST
power prior to cleaning the condenser. Failure to follow
this instruction may result in electrocution.

If your machine is water-cooled, check the water
lines for kinks or leaks. Kinks can occur when the
machine is moved back and forth for cleaning or
maintenance purposes. Deteriorated or cracked
water lines should be replaced only by an
authorized Taylor distributor.
Winter Storage
If the place of business is to be closed during the winter
months, it is important to protect the freezer by following
certain precautions, particularly if the building is subject
to freezing conditions.
Disconnect the freezer from the main power source to
prevent possible electrical damage.
On water-cooled freezers, disconnect the water supply.
Relieve pressure on the spring in the water valve. Use air
pressure on the outlet side to blow out any water
remaining in the condenser. This is extremely
important. Failure to follow this procedure may cause
severe and costly damage to the refrigeration system.
Your local Taylor distributor can perform this winter
storage service for you.
Wrap detachable parts of the freezer (such as dasher,
blades, dasher shaft, and freezer door) and place them in
a protected dry place. Rubber trim parts and gaskets can
be protected by wrapping them with moisture-proof
paper. All parts should be thoroughly cleaned of dried mix
or lubrication, which can attract mice and other vermin.
It is recommended that an authorized service technician
perform winter storage draining to make sure all water
has been removed. This will guard against freezing and
rupturing of the components.
7
7-2
Model C043
Operator Checklist
Troubleshooting Guide
Section 8
Table 8-1
Problem
Probable Cause
Remedy
Page
Ref.
1. Product is too stiff.
a. Flow regulator is set too low.
a. Adjust the flow regulator setting
6-6
2. The scraper blades
make a chattering noise.
a. Flow rate is too slow.
a. Adjust the flow rate.
6-8
3. Product is too soft.
a. Flow rate is too fast.
a. Adjust the flow rate.
6-6
b. There is a problem with the
refrigeration system.
b. Call an authorized service technician.
---
a. Inadequate level of mix in the mix
hopper.
a. Fill the mix hopper with mix.
6-6
4. The mix low indicator is
illuminated.
b. Bad electrical connection.
b. Call an authorized service technician.
---
5. The mix low indicator is
illuminated and the
product is too stiff.
a. The level of mix in the mix hopper is
inadequate and the flow rate is too
slow.
a. Fill the hopper with mix if further
production is required. If no further
production is required, open the flow
control all the way and place the
refrigeration switch in the OFF
position.
6-6
6. Beater motor won't start.
a. The beater motor overload has
tripped.
a. Turn the machine off. Press the reset
button and restart the machine.
---
b. The power switch is in the OFF
position.
b. Place the power switch in the ON
position.
---
c. The beater motor switch is in the
OFF position.
c. Place the beater motor switch in the
ON position.
---
d. The circuit breaker is off or the fuse
is blown.
d. Turn the breaker on, or replace the
fuse.
---
8
Troubleshooting Guide
Model C043
8-1
TROUBLESHOOTING GUIDE
Notes:
8
8-2
Model C043
Troubleshooting Guide
Section 9
Parts Replacement Schedule
Table 9-1
Part Description
Every 3 Months
Every 6 Months
Annually
Brush-Dbl End-Pump and Feed
Inspect and replace if
necessary.
Minimum
Brush-Draw Valve 1” OD x 2” x17”
Inspect and replace if
necessary.
Minimum
Brush-Barrel
Inspect and replace if
necessary.
Minimum
Brush-Rear BRG
Inspect and replace if
necessary.
Minimum
Brush-Mix Pump Body 3” x 7”
Inspect and replace if
necessary.
Minimum
Brush-End-Door-Spout-SS
Inspect and replace if
necessary.
Minimum
Gasket-Door
X
Bearing-Door-Front
X
Seal-Drive Shaft
X
Every 3 years
Blade-Scraper 30 Pitch
X
Blade-Scraper-Rear 30 Pitch
X
Spring-Beater Blade
X
9
Parts Replacement Schedule
Model C043
9-1
PARTS REPLACEMENT SCHEDULE
Notes:
9
9-2
Model C043
Parts Replacement Schedule
Section 10
Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from
Taylor to the market generally (the “Product”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as
follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the
applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or
remanufactured part, at Taylor’s option, to replace the failed defective part at no charge for the part. Except as
otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Product failure. This
limited warranty is subject to all provisions, conditions, limitations, and exclusions listed below and on the reverse (if
any) of this document.
Table 10-1
Product
Part
Limited Warranty Period
Soft Serve
Insulated Shell Assembly
Five (5) Years
Frozen Yogurt Shakes
Refrigeration Compressor (except service valve)
Five (5) Years
Smoothies
Beater Motors
Two (2) Years
Frozen Beverage
Beater Drive Gear
Two (2) Years
Batch Desserts
Printed circuit boards and Softech controls beginning with serial number H8024200
Two (2) Years
Parts Not Otherwise Listed in This Table or
Excluded Below
One (1) Years
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins ninety
(90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of purchase may
be required at time of service.
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by a Taylor-authorized distributor or service agency, and only if genuine, new Taylor parts are used.
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the
Taylor Operator's Manual.
4. Defective parts must be returned to the Taylor-authorized distributor or service agency for credit.
5. The use of any refrigerant other than that specified on the Product's data label will void this limited warranty.
10
Limited Warranty on Equipment
Model C043
10-1
LIMITED WARRANTY ON EQUIPMENT
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of defective
parts, replacement parts, or new Products.
2. Normal maintenance, cleaning, and lubrication as outlined in the Taylor Operator's Manual, including cleaning of
condensers.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator's Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work
promptly upon arrival.
7. Failure, damage, or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized
alteration, or improper operation or use as indicated in the Taylor Operator's Manual, including but not limited to the
failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.
8. Failure, damage, or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake, or any other
natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident, or condition beyond
the reasonable control of Taylor; operation above or below the electrical or water supply specification of the Product;
components repaired or altered in any way so as to, in the judgment of the Manufacturer, adversely affect performance,
or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs for any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product's data label will void this
limited warranty.
13. Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation
may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to
jurisdiction.
LIMITATION OF WARRANTY
10
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS, 
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS
UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES,
OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER
PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing by certified or registered letter to the following address,of any defect or complaint with
the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product
under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
10-2
Model C043
Limited Warranty on Equipment
Limited Warranty on Parts
Section 11
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, is pleased to provide this limited warranty on new Taylor genuine replacement components and parts
available from Taylor to the market generally (the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as
follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will
provide a new or remanufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part.
Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Part failure.
This limited warranty is subject to all provisions, conditions, limitations, and exclusions listed below and on the reverse
(if any) of this document.
Table 11-1
Parts Warranty Class Code or Part
Limited Warranty Period
Class 103 Parts¹
Three (3) Months
Class 212 Parts²
Twelve (12) Months
Class 512 Parts
Twelve (12) Months
Class 000 Parts
No Warranty
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time
of service.
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is
performed by a Taylor-authorized distributor or service agency.
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the
Taylor Operator's Manual.
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor
Limited Warranty on freezer or grill equipment.
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited
warranty.
1, 2
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer
equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
11
Limited Warranty on Parts
Model C043
11-1
LIMITED WARRANTY ON PARTS
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of
defective Parts, replacement Parts, or new Parts.
2. Normal maintenance, cleaning, and lubrication as outlined in the Taylor Operator's Manual, including cleaning of
condensers or carbon and grease buildup.
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including the
upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper assembly of
release sheets and clips as a result of grease buildup on the cooking surfaces, including but not limited to the
platen and plate, sides of the shroud, or top of the shroud.
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the
case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or other small
wares used during the cooking process or as a result of the use of cleaners, cleaning materials, or cleaning
processes not approved for use by Taylor.
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator's Manual, as well as any
release sheets and clips for the Product's upper platen assembly.
6. External hoses, electrical power supplies, and machine grounding.
7. Parts not supplied or designated by Taylor, or damages resulting from their use.
8. Return trips or waiting time required because a service technician is prevented from beginning warranty service
work promptly upon arrival.
9. Failure, damage, or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized
alteration or improper operation or use as indicated in the Taylor Operator's Manual, including but not limited to the
failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies.
10. Failure, damage, or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake, or
any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or
condition beyond the reasonable control of Taylor; operation above or below the gas, electrical, or water supply
specification of the unit in which a part is installed; or Parts or the units in which they are installed repaired or
altered in any way so as to, in the judgment of Taylor, adversely affect performance, or normal wear or
deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
13. Electricity, gas, or other fuel costs, or increases in electricity or fuel costs for any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is installed
will void this limited waranty.
15. Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this
limitation may not apply to you.
11
This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to
jurisdiction.
11-2
Model C043
Limited Warranty on Parts
LIMITED WARRANTY ON PARTS
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS, 
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER
THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES,
(INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES, OR
SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER
PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
11
Limited Warranty on Parts
Model C043
11-3
LIMITED WARRANTY ON PARTS
Notes:
11
11-4
Model C043
Limited Warranty on Parts
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising