Riccar 30 Series Pet Manual

Owner’s Manual
R30D & R30PET
CONTENTS
Getting Started
Important Safety Instructions Polarization Instructions Description of the Vacuum 2
3
4
Assembling the Vacuum
Attaching the Handle Unwinding the Power Cord 6
6
Operation
Reclining the Handle
Vacuuming Carpet
Bare Floor Cleaning
Brushroll Auto Shutoff Feature Dirt Sensing Display Carpet Height Adjustment Vacuuming Under Furniture Carrying the Vacuum
7
7
7
7
8
8
9
9
Attachment Cleaning
Wand Cleaning Cleaning Tools Adjusting the Suction Power for Tool Cleaning
Disconnecting the Hose
10
11
12
12
Maintenance and Care
Annual Checkup Power Cord Care When to Change The Vacuum Bag/Full Bag Indicator Light
Replacing the Vacuum Bag When to Change the Filters Replacing the HEPA Media Filter Replacing the Charcoal Filter Replacing the Granulated Charcoal Filter Replacing the Direct Air Motor Filter Lifetime Belt Jammed Brushroll Thermal Motor Protection 13
13
13
14
15
15
16
16
17
17
18
19
Problem Solving Guide
Troubleshooting Visit Riccar Vacuums Online How to Contact Your Authorized Retailer Key Replacement Parts For Best Performance Warranty 20
20
20
20
20
21
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
APPLIANCE. FOR HOUSEHOLD USE ONLY.
IMPORTANT:
The manufacturer cannot accept responsibility for damage
caused when the appliance is not used according to the
instructions, or for uses other than those for which it was intended.
WARNING:
To reduce the risk of fire, electric shock, damage or injury:
•D
o not leave appliance when plugged in.
Unplug from outlet when not in use
and before servicing.
• Do not use outdoors or on wet surfaces.
•D
o not allow to be used as a toy. Close
attention is necessary when used by
or near children.
•U
se only as described in this manual.
Use only manufacturer’s recommended
attachments.
•D
o not use with a damaged cord or
plug. If appliance is not working as it
should, has been dropped, damaged,
left outdoors, or dropped into water,
return it to your Authorized Riccar
Retailer for service.
•D
o not pull or carry by the cord, use
the cord as a handle, close a door on
the cord, or pull the cord around sharp
edges or corners. Do not run appliance
over the cord. Keep the cord away
from heated surfaces.
•D
o not unplug by pulling on the cord. To
unplug, grasp the plug, not the cord.
2
•D
o not handle the plug or appliance
with wet hands.
• D o not put any object into openings.
Do not use with any opening blocked;
keep free of dust, lint, hair and anything
that may reduce air flow.
•K
eep hair, loose clothing, fingers and all
parts of the body away from openings
and moving parts.
•D
o not pick up anything that is burning
or smoking, such as cigarettes, matches
or hot ashes.
• Do not use without a vacuum bag and/or
filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or
combustible liquids such as gasoline
or use in areas where they may be present.
• Do not attempt to service the unit while
appliance is plugged in.
SAVE THESE INSTRUCTIONS
POLARIZATION INSTRUCTIONS
Power Cord, 2-Wire Polarized Cord
To reduce the risk of electric shock, this product is equipped with a polarized
alternating current line plug (a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact a qualified electrician to replace the obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
3
DESCRIPTION OF THE VACUUM
1
2
3
11
15
12
16
13
17
14
24
18
4
19
23
5
10
20
420
6
7
8
4
9
21
22
DESCRIPTION OF THE VACUUM
1 ComfortGrip™ Handle
2 Main On/Off Power Switch
3 Carpet Button
4 Bag Compartment Latch (to Replace Vacuum Bag and Filters)
5 Crevice Tool
6 Full Bag Indicator
7 Brushroll Jam Indicator
8 Furniture Guard
9 LED Headlights
10 Vacuum Nozzle
11 Quick Release Upper Cord Hook
12 Power Cord
13 Stretch Hose
14 Carrying Handle
15 Hose Handle
16 Suction Release Valve
17 Wand Release Button
18 Tool Activation Dial
19 Hose Disconnect Cuff
20 Handle Release Pedal
2 1 Thermal Motor Protection Reset Button
22 Carpet Height Adjustment Dial
23 Telescopic Wand
24 Combination Dusting/Upholstery Brush
5
ASSEMBLING THE VACUUM
Attaching the Handle to the Vacuum
NOTE: Do not plug in the vacuum until it
is completely assembled.
The vacuum cleaner and the handle are
packed separately and require assembly.
•R
emove the handle screw located on
the back of the vacuum (Fig. 1). Insert
the handle downward into the body
of the vacuum (Fig. 2). Insert screw
and tighten.
•O
pen the bag compartment cover to
ensure a vacuum bag is in place.
Fig. 1
• Your vacuum is now ready for use.
•W
hen storing the vacuum, wrap the
cord clockwise around the top and
bottom cord hooks. Fasten the plug
to the wrapped cord using the channel
on the plug.
Fig. 2
Unwinding the Power Cord
•T
he Quick Release Upper Cord Hook
rotates to allow for quick access to the
power cord. Turn the upper cord hook
downward and you can quickly drop
the power cord to the floor without
unwinding it from the cord hooks (Fig. 3).
•W
hen storing the vacuum cleaner, turn
the Quick Release Upper Cord Hook to
the upright position and wrap the power
cord around the cord storage hooks.
Fig. 3
6
OPERATION
This vacuum is intended for household use only.
Reclining the Handle
Press the Handle Release Pedal with your
foot to recline the handle.
Vacuuming Carpet
or carpet cleaning, push the On/Off
F
Switch to the “On” position. The Carpet
Button will illuminate indicating the
carpet cleaning setting is on (Fig. 1).
The carpet cleaning setting will remain
on until the Carpet Button is pushed and
the button is no longer illuminated.
Press
ON
OFF
Bare Floor Cleaning
or bare floor cleaning (i.e. tile, wood,
F
or vinyl), push the On/Off Switch to the
“On” position. Push the Carpet Button.
The Carpet Button will no longer be
illuminated indicating the carpet setting
is off and the bare floor setting is on (Fig. 2).
Carpet Cleaning
Fig. 1
Brushroll Auto Shut-Off Feature
When the vacuum is turned on and in
the upright position, the brushroll will
not spin to reduce the possibility of
damaging flooring surfaces. The brushroll
will spin when the handle is lowered, if
the Carpet Button is illuminated.
lways turn the vacuum cleaner off before
A
unplugging it from the electrical outlet.
Press
ON
OFF
Press
Bare Floor Cleaning (Wood, Tile, etc.)
Fig. 2
7
OPERATION
Carpet Height Adjustment
There are various carpet height settings
designed for numerous flooring surfaces.
•L
ocate the height adjustment dial just
above the right rear wheel, and rotate
the dial to the desired height.
Max
Shag/Frieze or similar length carpet
X Hi
Plush carpet
High Medium pile carpet
Auto General setting
Floor Hard floors
Low
Low pile carpet
• If it becomes difficult to push the
vacuum across the carpet, adjust
the dial to a higher carpet setting.
8
OPERATION
Vacuuming Under Furniture
Your vacuum will lay flat on the floor for
effective cleaning under beds and tables.
•P
ress the Handle Release Pedal once
for normal vacuuming (Fig. 1).
•P
ress the Handle Release Pedal a second
time to enable the vacuum to lay flat on
the floor (Fig. 2).
Carrying the Vacuum
To safely transport your vacuum,
especially when carrying the vacuum
up and down stairs, use the Carrying
Handle located at the top of the bag
compartment (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
9
ATTACHMENT CLEANING
Wand Cleaning
Your vacuum is a comprehensive cleaning
system equipped with an upholstery tool,
dusting brush, crevice tool, telescopic
wand and a stretch hose.
• Remove
the Telescopic Wand from the
body of the vacuum by pulling it up and
out of the holder (Fig. 1).
•T
urn the Tool Activation Dial counterclockwise to the “Tools On” setting
(Fig. 2). The Telescopic Wand is now
activated for quick cleaning.
Fig. 1
•A
ttach any of the tools to the end of the
Telescopic Wand.
TO
•E
xtend the wand by grasping the wand
cuff and pushing outward to the desired
length (Fig. 3).
•W
hen finished with tool/wand cleaning,
turn the Tool Activation Dial clockwise
to the “Tools Off” setting (Fig. 4). Insert
the wand back into the vacuum and
secure it by pushing the curved handle
into the holder.
O
LS
O FF
T O O LS O N
Tools On
Fig. 2
Fig. 3
Align
Arrows
for
Carpet
Cleaning
S OFF
LS
TOO
OL
10
T
O
ON
Tools Off
Fig. 4
ATTACHMENT CLEANING
Cleaning Tools
Your vacuum is equipped with a dusting
brush, upholstery tool and crevice tool.
•R
emove the cleaning wand from the
vacuum and turn the Tool Activation
Dial to the “Tools On” setting (See
page 10).
•A
ttach any of the tools onto the end
of the telescopic wand.
Fur-Get-It!
Pet Hair Remover Tool (R30PET model)
Ideal for removing pet hair from
upholstery, stairs and vehicles.
Dusting Brush
Ideal for table tops, shelves and blinds.
Pet Hair Removal Tool
Upholstery
Tool Ideal for soft surfaces like chairs and
couches. Remove the dusting brush clip
for upholstery cleaning.
Crevice Tool
Ideal for tight places like between seat
cushions or corners.
Dusting Brush
Dusting
Brush Clip
Crevice Tool
Upholstery Tool
11
ATTACHMENT CLEANING
Cleaning Tools (continued)
Cleaning tools can also be attached to
the curved handle for tasks where the
wand is not needed.
•D
isconnect the wand from the curved
handle by pressing the Wand Release
Button (Fig. 1).
•A
ttach any of the cleaning tools directly
to the curved handle.
Fig. 1
Adjusting the Suction Power for
Tool Cleaning
Full suction power may be too strong
for some cleaning situations. For example,
reduced suction power would be
appropriate for cleaning sheer curtains.
•O
n the curved handle, locate the Suction
Relief Valve and slide it backward (Fig. 2).
This reduces the suction power coming
through the tool. Slide the valve forward
when finished to restore full suction power.
Fig. 2
Disconnecting the Hose
The hose can be disconnected from the
vacuum by pressing the two buttons on
the sides of the Hose Disconnect Cuff
located low on the back of the vacuum
(Fig. 3).
This allows you to attach an optional
extension hose for longer reach and is
also a method for removing debris from
the hose.
Fig. 3
12
MAINTENANCE AND CARE
Annual Checkup
To keep your vacuum in peak operating
condition, it is recommended you
bring your vacuum to an Authorized
Riccar Vacuum Retailer for an annual
checkup. The Retailer will conduct
a comprehensive examination to ensure
your vacuum is in top operating condition.
Power Cord Care
Full Bag
Brushroll
• If the cord or plug has any apparent
damage, refrain from using the vacuum.
Please visit an Authorized Riccar
Vacuum Retailer for a new cord
or plug.
•W
hen the vacuum is in use, hold the
cord to keep from running over it.
Yellow Warning Light Indicates a
Full Bag Condition
•A
void obstructions and do not pull the
cord around sharp edges or corners.
•A
lways keep the cord away from heated
surfaces and never close doors on it as
this may cause damage to the wiring.
•T
o unplug, always grasp the plug, not
the cord.
When to Change the Vacuum Bag
The Full Bag Indicator Light is designed
to show when the bag is full or when
there is a clog in the vacuum.
The light could also come on when
vacuuming fine powders such as flour or
drywall dust. These materials can quickly
block the bag pores, significantly reducing
airflow before the bag is actually full.
The vacuum bag should still be changed.
The light may also come on during
attachment cleaning. If the light goes
off when attachments are no longer in
use, the vacuum bag does not need to
be changed.
NOTE: The vacuum bags are disposable
and intended to only be used once.
Do not attempt to reuse the bag, as
suction and filtration performance will
be greatly reduced.
13
MAINTENANCE AND CARE
Replacing the Vacuum Bag
NOTE: Unplug the vacuum cleaner
from the electrical outlet before changing
the bag.
•O
pen the bag compartment by lifting up
the latch on the bag compartment cover.
•R
emove the used vacuum bag by
pulling the blue bag collar tab away
from the vacuum (Fig. 1). Slide the
used bag out of the holder which
automatically seals the bag (Fig. 2).
Discard the used bag.
Fig. 1
•T
o install a new bag, slide the bottom
of the blue bag collar into the bag
holder until it “snaps” into place (Fig. 3).
•P
ush the top of the bag collar upward
until the bag holder “snaps” into place
on the vacuum (Fig. 4).
•T
uck the bag corners into the bag
compartment before replacing the
bag compartment cover.
Fig. 2
•R
eplace the bag compartment cover
and press down on the latch to secure
it into place.
Fig. 3
Fig. 4
14
MAINTENANCE AND CARE
When to Change the Filters
NOTE: Unplug the vacuum cleaner from the
electrical outlet before changing the filters.
At minimum, it’s recommended to replace
the filters once a year or after using 12
vacuum bags, whichever comes first.
If someone in your household is sensitive
to airborne allergens, it is recommended
to change the filters after every six
vacuum bags.
Replacing the HEPA Media Filter
• Remove the bag compartment cover.
•L
ocate the HEPA Media Filter on the
front of the vacuum.
•G
rasp the tab on the left to remove the
used filter and discard it.
•T
o insert a new filter, position the tabs
on the right side of the cartridge into
the vacuum. Then snap it into place.
•R
eplace the bag compartment cover
and press down on the latch to secure
it into place.
NOTE: Filters cannot be washed and reused.
15
MAINTENANCE AND CARE
Replacing the Charcoal Filter
(R30D model)
•R
emove the bag compartment cover
and locate the filter on the left side
of the bag compartment.
•P
ull the front tab away from the vacuum
to remove the filter holder (Fig. 1).
•R
emove and throw away the used
charcoal filter.
• Insert a new charcoal filter under the
tabs in the holder. Then align the back
of the filter holder into the vacuum first
and snap it into place behind the tab.
•R
eplace the bag compartment cover
and press down on the latch to secure
it into place.
Replacing the Granulated Charcoal
Filter (R30PET model)
•O
pen the bag compartment lid and
locate the filter on the left side of the
bag compartment.
•U
se the latch on the side to remove and
discard the entire filter cartridge.
• Insert a new granulated charcoal filter
cartridge and snap it into place behind
the tab.
•C
lose the bag compartment cover and
press down on the latch to secure it
into place.
NOTE: Filters cannot be washed and reused.
16
Fig. 1
MAINTENANCE AND CARE
Replacing the Direct Air
Motor Filter
•P
ress the handle release pedal with
your foot, and tilt the handle back
until it stops. Press the pedal again
to lower the handle to the floor (Fig. 1).
•P
ull the black filter cover latch to
access the filter (Fig. 2).
• Remove and discard the used filter.
• Insert a new direct air motor filter and
snap the filter cover back into place.
•R
eturn vacuum handle to its upright
position.
Fig. 1
Lifetime Belt
Your vacuum belt is covered with a
lifetime warranty. Should the vacuum
belt break, simply bring your vacuum to
your Authorized Riccar Vacuum Retailer
for a free replacement.
Fig. 2
17
MAINTENANCE AND CARE
Jammed Brushroll
CAUTION! To Reduce the Risk of Injury
From Moving Parts, Unplug Before Servicing.
If an object, such as a throw rug or article
of clothing is ever picked up into your
vacuum, the vacuum will sense this
jammed brushroll condition and turn off
the brushroll. When this happens, the
Brushroll Jam Indicator on the top of
the nozzle will light up in red.
Full Bag
Brushroll
• Turn off and unplug the vacuum.
• Remove the cause of the jam.
• Turn the vacuum back on.
• If the brushroll is free of obstructions and
the Brushroll Jam Indicator is still lit, it’s
likely the clogged condition is located
in the vacuum motor fan. If so, please take
your vacuum to an Authorized Riccar
Vacuum Retailer for service.
18
Red Warning Light Indicates a
Jammed Brushroll Condition
MAINTENANCE AND CARE
Thermal Motor Protection
CAUTION! To Reduce the Risk of
Injury From Moving Parts, Unplug
Before Servicing.
Thermal Reset
1. Unplug machine 3. Correct problem
2. Locate problem 4. Press reset button
source (clogged
If problem persists,
consult owner’s manual
hose or full bag)
or contact retailer.
Your vacuum is equipped with a
safeguard to recognize when the
vacuum might overheat and shuts
itself off. When this happens the
headlights are still on but the motors
shut off. Common reasons why
a vacuum may overheat include
operating with a full bag or when
there is a clog in the vacuum.
If the Thermal Motor Protection
System shuts off your vacuum,
follow these steps:
• Unplug the vacuum.
• Inspect the vacuum for a full bag
condition or a hose clog and
correct the problem.
• Locate the Thermal Motor Protection
Reset Button on the back of the
vacuum. Press the button and
resume vacuuming.
If problem continues, contact your
Authorized Riccar Vacuum Retailer.
19
PROBLEM SOLVING GUIDE
Troubleshooting
WARNING! To reduce the risk of electrical shock or injury from moving parts,
unplug the vacuum before servicing or cleaning the vacuum.
CAUTION! To Reduce the Risk of Electric Shock, Do Not Handle Plug or Appliance
with Wet Hands.
PROBLEM
Vacuum won’t
turn on.
Vacuum won’t
pick up or low
suction.
Dust escaping
from vacuum
CHECK POINT
POSSIBLE SOLUTION
Power Cord
Plug unit in firmly.
House Fuse or Breaker
Check house fuse or breaker. Replace
fuse/reset breaker.
Needs Service
Take to an Authorized Riccar Vacuum
Retailer.
Carpet Button
ress “Carpet” button on – it will
P
illuminate when it’s on.
Vacuum Bag
Replace full bag.
Filter
Replace clogged filter.
Hose
Remove obstacle.
Brushes
Replace brush strips.
Belt
Take to an Authorized Riccar Vacuum
Retailer.
Tool Activation Dial
Turn Tool Activation Dial to “Off” position
for carpet and bare floor cleaning.
Dust compartment
cover
Attach the dust compartment cover and
secure latch.
Filter
Review filter installation (pages 15-17).
Any other service should be performed by an Authorized Riccar Vacuum Retailer.
To locate your nearest Authorized Retailer, visit our website at
Riccar.com or call 888-674-2227.
Key Replacement Parts
• Genuine HEPA Media Vacuum Bags: RNH-6
• Genuine Filter Sets: S
F30P (R30PET model), SF30D (R30D model)
For Best Performance
• Keep your vacuum clean and in good operating condition.
• Change the vacuum bag once a month or when the full bag light is illuminated
to maximize cleaning performance.
• Always use genuine Riccar vacuum bags and replacement parts. Use of other
products may result in poor cleaning performance, potential vacuum cleaner
damage and may void vacuum warranty. Genuine products are designed for
maximum cleaning performance.
• Have your vacuum checked annually by your Authorized Riccar Vacuum Retailer.
• Store your vacuum carefully in a dry area.
• For optimum cleaning performance and safety, follow your owner’s manual instructions.
20
WARRANTY
What is Covered:
This warranty covers any defects in material and workmanship in your new vacuum
and applies exclusively to the original purchaser.
How Long Coverage Lasts:
Warranty coverage for your R30PET model lasts seven years. Warranty coverage
for your R30D model vacuum lasts six years. Household models used commercially
are only warranted for 90 days.
What is Not Covered:
•D
amage to the vacuum which occurs from neglect, abuse, alterations, accident,
misuse or improper m
­ aintenance.
• Normal replacement items: disposable bags, disposable filters and agitator brushes.
•D
amage associated with or resulting from the use of non-genuine parts including
normal replacement items.
What We Will Do:
This warranty provides, at no cost to you, all labor and parts to keep this vacuum
in correct o
­ perating condition during the warranted period.
How to Get Service:
Warranty service can only be obtained by presenting the vacuum to an Authorized
Riccar Retailer. A proof-of-purchase and product serial number will be required
before service is rendered. To locate your nearest service center, please call
888-674-2227 or visit Riccar.com.
THIS WARR ANT Y IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER
WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED, (INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE). THIS WARRANTY DISCLAIMS LIABILITY FOR ­I NCIDENTAL OR
CONSEQUENTIAL DAMAGES.
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Owner’s Warranty Information (keep this for your records)
Store name
Store Address City State
Telephone
Serial number
Zip Date of purchase
Model number
Register your warranty online at Riccar.com
21
Riccar.com
888-674-2227
1760 Gilsinn Lane
Fenton, MO 63026
©2018 Tacony Corporation
B503-7004D
">