Billy Goat | OS901SPH | manual | Billy Goat OS901SPH Overseeders Manual

Billy Goat OS901SPH Overseeders Manual
ot
fo
rR
ep
ro
du
ct
io
n
OSSP Owner’s Manual
N
SELF PROPELLED OVERSEEDER Owner's Manual
OS901SPS, OS901SPH
Accessories
Replacement Parts
SEED BOX BONNET
CHARIOT KIT
REEL KIT
BLADE KIT
A convenient way to
enclose the seed box.
Allows the user to ride
behind the unit and
decrease fatigue from
walking.
Use to replace worn or
damaged reels.
Use to replace worn or
damaged blades on the
reel.
P/N 351617
P/N 351601
P/N 351603
P/N 351610
Part No 351520 (A)
1
Form No F082815A
OSSP Owner’s Manual
CONTENTS
3
n
SPECIFICATIONS AND SOUND/VIBRATION
PACKING CHECKLIST
ASSEMBLY
OPERATION
4
ro
du
ct
io
INSTRUCTION LABELS
MAINTENANCE & TROUBLESHOOTING
6
7-8
9-10
11-22
N
ot
fo
rR
ep
PARTS LIST
5
Part No 351520
2
Form No F082815A
OSSP Owner’s Manual
SPECIFICATIONS
OS901SPH
Engine: HP’
9.0 HP (6.7kW)
9.0 HP (6.7kW)
Engine: Model
EX270D50021
GX270K1QA2
Engine: Type
Subaru
Honda
Engine: Fuel Capacity
6.4 qt. (6.1 L)
5.6 qt. (5.3 L)
Engine: Oil Capacity
1.06 qt. (1 L)
1.16 qt. (1.1 L)
ro
du
ct
io
Total Unit Weight:
n
OS901SPS
314# (142 kg)
Max. operating slope
15
Sound test in accordance with
2000/14/EC
Sound at operators ear
20
104 dB(a)
84 dB(a)
2
2
0.81g (7.95 m/s )
0.81g (7.95 m/s )
SOUND LEVEL 84 dB(a) at Operators Position
rR
ep
104
o
104 dB(a)
84 dB(a)
Vibration at operator position
SOUND
323# (147 kg)
o
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 10-13-2010 under the conditions listed
below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for
the sound power level for your model.
Sunny
o
o
73 F (23 C)
11 mph (17 kmh)
South West
27%
30.34Hg (770 mm Hg)
fo
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
2
VIBRATION LEVEL .81g (7.95m/s )
N
ot
VIBRATION DATA
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated
vibration test equipment. Tests were performed on 10-13-2010 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
Part No 351520
Sunny
o
o
66 F (19 C)
3 mph (4.8kph)
East
30.2%
29.9Hg (101.3kpa)
3
Form No F082815A
OSSP Owner’s Manual
INSTRUCTION LABELS
®
LABEL DANGER KEEP HANDS
AND FEET AWAY
ITEM #145 P/N 400424
LABEL CLUTCH ITEM #142
P/N 500177
LABEL INSTRUCTIONS SEEDER BOX
ITEM #56 P/N 351501
(pg 12)
ENGINE LABELS
LABEL TRANS. RELEASE
ITEM #146 P/N 351507
LABEL DEPTH GAUGE
ITEM #59 P/N 351504
rR
ep
LABEL CAUTION GUARDS
ITEM #133 P/N 900327
ro
du
ct
io
n
The labels shown below were installed on your BILLY GOAT Overseeder. If any labels are damaged or missing, replace them
before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in
ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers
shown.
fo
SUBARU
LABEL SEED METERING
ITEM #66 P/N 351503
(pg 12)
HONDA
READ OWNER
’S MANUAL
BEFORE OPERA
TION.
LIRE LE MANUEL
D UTILISA
TEUR
AVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER
MANUAL
LEIDO EL
HONDA MOTOR CO. , LTD. MADE IN JAPAN
OIL ALERT
N
ot
WHEN OIL LEVELLOW,
ENGINE STOPS IMMEDIA
TELY.
.
Part No 351520
4
Form No F082815A
OSSP Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Overseeder is shipped from the factory in one carton.
n
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box, the Handle Assembly is attached to the unit and
cables could snag.
PARTS BAG & LITERATURE ASSY
ro
du
ct
io
PUT OIL IN ENGINE BEFORE STARTING
Warranty card P/N- 400972, Owner’s Manual P/N-351520, General Safety and Warnings Manual P/N-100295, Declaration of
Conformity P/N-351508.
Boxing Parts
Checklist
Subaru 9 HP
Parts bag
P/N-351009
Foot pedal
assembly
N
ot
fo
rR
ep
Honda 9 OHV
Part No 351520
5
Form No F082815A
OSSP Owner’s Manual
ASSEMBLY
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-22.
1. UNFOLD the upper handle and slide handle lock loops (item 35) into place to secure the upper handle to the lower.
2. ATTACH the bar of the foot pedal to the bracket located on the engine. Use the lock nut (item 93) from the parts bag.
3. ATTACH the pedal section to the rear of the frame between the two brackets by aligning the holes and inserting the tube
(item 201) from the parts bag.
n
4. TAP the two pins (item 202) into both ends of the tube installed in step 3, and using pliers, spread the cotter pins to keep
it from coming out.
93
fo
rR
ep
6. CONNECT spark plug wire.
ro
du
ct
io
5. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Make sure to adjust
the machine so that the engine is level during checking. See engine manufacturers’ instruction manual.
ot
202
N
201
Part No 351520
6
Form No F082815A
OSSP Owner’s Manual
OPERATION
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-22.
FOLDING HANDLE
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by sliding the
handle lock loops (item 35) up. This releases the upper handle, allowing it to be folded over the unit.
BLADE POSITION & DEPTH CONTROL LEVER
ro
du
ct
io
The depth of the blades can be raised or lowered by rotating the knob located at the rear of the
machine. The relative depth of the blades can be gauged by using the depth scale located on
the rear of the machine and the bar next to it. (See Fig. 1)
n
ADJUSTING BLADE DEPTH
The blades can be raised or lowered into the ground by the height adjustment foot pedal at the
rear of the unit. The blades will be in lowered position when the foot pedal is unlocked from the
bracket and will be in transport position when the pedal is locked to the bracket. See Fig. 2 & 3
for operation. The resulting blade depth can be adjusted higher or lower.
Fig. 1
Pressing on the outside tabs of the pedal will allow it to unlock
from the bracket and lower into position. (See Fig. 2)
rR
ep
Pressing on the center of the pedal and pushing it into the bracket
will allow it to be locked in transport position. (See Fig. 3)
VERTI-CUTTING OPERATION
Fig. 2
Fig. 3
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e. driveway, or sidewalk).
ENGAGE BLADES: Push the Reel Lever down on the operator handle (upper left side). NOTE: When engaging the blades in
heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operator handle lifting the front wheels slightly.
Engage the blades. Slowly lower the unit into the turf.
fo
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be removed and deposited on top
of the healthy grass. Grass runners should be cut and ready for removal. If excessive damage occurs to healthy grass, adjust
the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If
a large drop in engine RPM occurs, or bounces during operation, the blade depth is set too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited over the top of the lawn. We
suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch/stems.
ot
OVERSEEDING OPERATION
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
2
2
N
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft [4.5 kg. per 93 m ]) Adjustments to
the seed drop is located on the front of the unit on the seed dial and should be used in conjunction with the seed chart on the
console.
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2" (6-12 mm) below a flat surface (i.e. driveway,
or sidewalk).
ENGAGE REEL AND SEED DROP: Push down on the reel lever on the operators handle. NOTE: When engaging the reel in heavy
load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage
the reel. Slowly lower the unit into the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to
healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or
east-west). NOTE: If a large drop in engine RPM occurs, or bounces during operation, the blade depth is set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed supplier’s directions.
Part No 351520
7
Form No F082815A
OSSP Owner’s Manual
ADJUSTING SEED RATE
ro
du
ct
io
n
To set the seed flow rate, loosen the knob on the indicator dial and turn it to the
corresponding stop setting on the seed application chart (below or on the console) for the
type and amount of seed being used. (See Fig. 4)
INSTRUCTION LABEL P/N 351501
rR
ep
Fig. 5
Fig. 4
Fig. 6
*****TIPS*****
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core samples from area to be treated. A core can
be cut using a piece of PVC, or metal pipe. Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to
determine the depth of thatch in your yard.
MOW
Mow the lawn to its normal cut height. Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
fo
INSPECT
Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can present a hazard during work.
IDENTIFY
Mark all fixed objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc.
ot
THATCH
Thatch is a dense layer of dead grass, clippings, and roots that builds up over time at the base of the lawn preventing air, water, and
fertilizer from reaching the soil. This can cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of thatch will keep your lawn in good health.
N
HEAVY THATCH
Lawns with an excessive amount of thatch will require multiple treatments for effective removal. Trying to remove excessive thatch
(greater than 3/4"[19 mm] deep) in one treatment will damage or destroy the living part of the lawn. It is best to remove heavy thatch in
seasonal treatments (i.e. spring, and fall).
SLOPES
Rake slopes across not up and down the slope. This is much easier and safer for the operator and is better for the lawn. Raking across
will help to reduce runoff during watering and allow the sloped ground to hold more seed, fertilizer, and water. The unit’s maximum
operating slope is 35% or 19°.
DEPTH
The wide range of depth adjustment on your unit is provided to allow for blade wear. Setting the reel deeper will not produce better results.
The flail reel is intended to be set so it just touches the surface on flat ground. The slicing reel should be set even with the ground for vertislicing work, and set to a maximum 1/2" depth for overseeding. Setting the reel deeper will only result in premature wear on the unit (i.e.
failed belt). If you desire to work the ground deeper than the above guidelines, it should be done gradually in multiple passes.
SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before starting (i.e. approximately 2" tall for fescue grass).
For the best result, slice/overseed in criss-cross pattern (See Fig. 5 & 6).
Part No 351520
8
Form No F082815A
OSSP Owner’s Manual
MAINTENANCE
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-22.
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily)
Every 25 Hours
Inspect for loose, worn or damaged parts
Check engine oil

Inspect belts
n

Engine (See Engine Manual)
Grease bearings
ro
du
ct
io


Inspect and clean engine air filter
Oil height adjustment linkage
SLICING BLADE WEAR


1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear and immediately replace any deformed or cracked blades. Measure the overall diameter of the
blade.
rR
ep
5. If blades are warped or the diameter of the blade is 6.75" (171 mm) in length, they must be replaced. NOTE: We
recommend replacing all the blades at once.
ENGINE BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove three screws (item 114) holding the belt guard (item 19) in place.
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place.
fo
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and remove the mule
assembly leaving the belt on the transmission.
7. Remove the carriage bolt and nuts holding the right bearing on the jackshaft. Do not remove the bearing and pulley.
8. Remove the belt guard (item 58) by removing the three screws (item 114).
ot
9. Walk the belt off of the crankshaft pulley, and then slide it down the jackshaft to the bearing hole. This will allow the belt
to be slid around the mule pulley.
N
10. Replace the belt by feeding it into the hole and around the pulley where the old one was removed. Make sure it is seated
in the jackshaft pulley and then walk it onto the crankshaft pulley making sure it is inside the belt fingers.
11. Reattach the bearing and tighten the hardware securely.
12. Reattach the mule drive and belt, making sure that the belt is seated properly in the transmission pulley and the mule
drive assembly.
13. Check the idler tension on the belt when the drive lever is engaged, if it is too loose, the spring (item 82) holding the idler
arm will need to be replaced.
14. Reattach the guards, tire, spring and spark plug and make sure of proper operation.
Part No 351520
9
Form No F082815A
OSSP Owner’s Manual
MULE BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove (3) screws (item 114) holding the belt guard (item 19) in place.
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place. This will allow access to the belt.
n
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and then sliding it off of the
transmission. Discard old belt.
ro
du
ct
io
7. Install new belt using same procedure to walk the belt into the groove, making sure it is seated fully in all pulleys. Reattach
the mule drive assembly.
8. With new belt installed, pull the drive levers up and make sure the idler pulley puts tension on the cable. The proper
adjustment should have the drive lever fully engaged and the belt should be snug on the pulleys.
9. Re-install the belt guard, spring, and tire, then reattach the spark plug.
REEL BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Remove two screws (item 38) holding the belt guard (item 20) in place
3. Remove the belt (item 17) by rotating the reel pulley (item16) and walking it out of the groove. Discard old belt.
4. Install new belt using same procedure to walk the belt into the groove, making sure that it is inside the belt fingers.
5. With new belt installed, push the reel drive lever down and make sure the idler pulley puts tension on the cable. The proper
adjustment should have the blade lever fully engaged and the belt should be snug on the pulleys.
TROUBLESHOOTING
Possible Cause
Damaged or missing blades. Loose
handle bolts. Loose engine bolts.
Solution
Stop work immediately. Replace any
damaged or missing blades. Tighten all
loose nuts and bolts.
Raise blades so that they just touch
the ground on a level surface.
Blades set too deep into ground.
Engine will not start
Stop switch off (Honda only). Throttle Check choke position.
in off position.
Out of gasoline or bad, old gasoline.
Check gasoline.
Spark Plug wire disconnected.
Connect spark plug wire.
Gas valve off.
Turn on gas valve.
Dirty air cleaner.
Clean or replace air cleaner. Contact a
qualified service person.
Debris locked against reel, or drive
pulleys. Engine problem.
Pull spark plug wire and remove debris.
Contact an engine servicing dealer for
engine problems.
N
fo
Engine stalls or labors when
raking
ot
Problem
Abnormal vibration
rR
ep
6. Re-install the belt guard and reattach the spark plug.
Engine is locked, will not pull
over
Part No 351520
10
Form No F082815A
OSSP Owner’s Manual
SLICING REEL ASSY
P/N 351603
3
ro
du
ct
io
n
4
1
2
rR
ep
ITEM NO
DESCRIPTION
1
SHAFT VERTICUTTING REEL OS900SP
2
BLADE VERTICUT OS900SP
3
SPACER PM REEL OS900SP
4
SPACER HARDENED REEL OS900SP
5
SPRING DISC 7/8" ID
6
NUT 7/8"-14 NC
PART NO.
351111
351305
351261
351297
351298
350341
5
QTY
1
11
10
1
1
1
45°
N
ot
fo
ORIENTATION HOLE
6
Part No 351520
EACH BLADE SHOULD BE ROTATED CLOCKWISE 45 DEGREES. USE THE HOLE
IN THE BLADE TO SET ORIENTATION.
11
Form No F082815A
OSSP Owner’s Manual
N
ot
fo
rR
ep
ro
du
ct
io
n
OSSP ENGINE ASSEMBLY PARTS DRAWING
Part No 351520
12
Form No F082815A
OSSP Owner’s Manual
OSSP ENGINE ASSEMBLY PARTS LIST
N
ot
fo
rR
ep
n
ro
du
ct
io
ITEM NO.
DESCRIPTION
1
ENGINE HONDA 9HP
ENGINE SUBARU 9HP
3
ENGINE BASE WA
7
JACKSHAFT WA
18
BELT GATES #8954-0298
50
ENGINE BRACKET WA
51
LINKAGE FOOT CONTROL WA
57
BRACKET GUARD BELT UPPER
58
GUARD BELT UPPER OS900SP
78
PULLEY IDLER 4" OD X 3/8 BORE
80
ARM IDLER WA UPPER
81
PULLEY 3.50" OD X 1.00" BORE
82
SPRING IDLER UPPER
91
BOLT SHOULDER 1/2" X 2"
93
NUT LOCK 5/16"-18
95
WASHER SPLIT LOCK
96
WASHER LOCK 7/16' S/T MED
99
SCREWCAP 7/16"-20 X 1" HCS GR. 8 W/PATCH
101
SCREWCAP 5/16"-24 X 1" GR 8 W/PATCH
102
SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
108
WASHER 5/16 FLAT
112
BOLT CARRIAGE 5/16"-18 X 1 1/2" ZP
113
LOCK NUT 3/8-16
114
SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F
116
WASHER 3/8" SAE
118
NUT FLANGE 5/16-18 ZP
119
PLATE IMPELLER WASHER PB110
121
SPACER 1.25 OD X 1.010 ID X .938 THK
133
LABEL DANGER
134
SCREWCAP 5/16"-18 X 1 3/4" HCS ZP
135
KEY SQ 1/4" X 1"
196
ENGINE BASE WA OS900SP W/LABELS
199
LABEL MADE IN U.S.A.
OS901SPH
OS901SPS
PART NO. QTY PART NO. QTY
430287
1
351299
1
351125
1
351125
1
351107
1
351107
1
351211
1
351211
1
351121
1
351121
1
351122
1
351122
1
351203
1
351203
1
351116
1
351116
1
500113
1
500113
1
351113
1
351113
1
351296
1
351296
1
351275
1
351275
1
520031
1
520031
1
8160002
7
8160002
7
8177011
6
8177011
6
8177013
1
8177013
1
510213
1
510213
1
400164
6
400164
6
8041053
1
8041053
1
8171003
8
8171003
8
8024042
1
8024042
1
8160003
2
8160003
2
890359
3
890359
3
8172009
2
8172009
2
350346
2
350346
2
850443
1
850443
1
351413
2
351413
2
900327
2
900327
2
8041031
5
8041031
5
9201113
1
9201113
1
351612
1
351612
1
520116
1
520116
1
Part No 351520
13
Form No F082815A
OSSP Owner’s Manual
N
ot
fo
rR
ep
ro
du
ct
io
n
OSSP REEL/REEL DRIVE ASSEMBLY PARTS DRAWING
Part No 351520
14
Form No F082815A
OSSP Owner’s Manual
OSSP REEL/REEL DRIVE ASSEMBLY PARTS LIST
rR
ep
ot
N
Part No 351520
QTY
1
1
1
2
2
2
1
1
2
1
1
1
1
1
1
1
2
1
4
1
2
4
2
4
5
1
6
4
1
1
1
1
1
1
1
n
QTY
1
1
1
2
2
2
1
1
2
1
1
1
1
1
1
1
2
1
4
1
2
4
2
4
5
1
6
4
1
1
1
1
1
1
1
OS901SPS
PART NO.
351125
351101
351126
350209
351210
351213
351117
890456
791080
441150
351012
351206
351408
351269
351268
351112
350114
520031
8160002
8177011
8041038
8041050
8171003
350346
8161042
351295
351264
8024039
9201080
351221
440124
440193
8041056
400164
351607
ro
du
ct
io
DESCRIPTION
ENGINE BASE WA
HOUSING VERTICUTTER WA OS900SP
FRAME SUPPORT OS900SP WA
BEARING 3/4" CAST FLANGE W/ZERK
PULLEY 0.75" ID X 4" 4L SECTION
BELT 4L
GUARD REEL BELT OS900SP
LABEL DECAL SM CIRCLE
SER HEX WASHER 3/8" - 16
WASHER 1.125 OD X .344 ID X 10 GA
REEL ASSY OS900SP
GUARD BEARING REEL OS900SP
SPACER SEED BOX AXLE OS900SP
DEFLECTOR RUBBER OS900SP
BAR CLAMP DEFLECTOR
ARM IDLER WA REEL ENGAGE
PULLEY
BOLT SHOULDER 1/2" X 2"
NUT LOCK 5/16"-18
WASHER SPLIT LOCK
SCREWCAP 5/16-18 X 3 1/2"
SCREWCAP 3/8"-16 X 1"
WASHER 5/16" FC
NUT FLANGE 5/16-18 ZP
NUT LOCK 3/8-16 LT WT THIN ZP
SPRING IDLER MULE DRIVE
SER HEX WASHER FLNG SCREW 5/16"-18 X 3/4"
BOLT CARRIAGE 5/16"-18 X 3/4" ZP
KEY 3/16" SQ X 1 1/4"
CABLE CLUTCH SEEDING CONTROL
PIN CLEVIS 1/4" X .50"
PIN CLIP HITCH 0.051" X 3/4"
SCREWCAP 3/8"-16 X 2 1/2" ZP
SCREWCAP 5/16"-24 X 1" GR.8 ZP W/PATCH
GUARD REEL BELT OS900SP W/LABELS
fo
ITEM NO.
3
4
5
13
16
17
20
21
38
41
49
54
55
68
69
76
77
91
93
95
103
104
108
118
120
124
127
129
135
138
147
150
187
191
193
OS901SPH
PART NO.
351125
351101
351126
350209
351210
351213
351117
890456
791080
441150
351012
351206
351408
351269
351268
351112
350114
520031
8160002
8177011
8041038
8041050
8171003
350346
8161042
351295
351264
8024039
9201080
351221
440124
440193
8041056
400164
351607
15
Form No F082815A
OSSP Owner’s Manual
N
ot
fo
rR
ep
ro
du
ct
io
n
OSSP HANDLE ASSEMBLY PARTS DRAWING
Part No 351520
16
Form No F082815A
OSSP Owner’s Manual
OSSP HANDLE ASSEMBLY PARTS LIST
rR
ep
ot
N
Part No 351520
OS901SPS
PART NO.
351126
791056
351406
360298
351208
500267
890132
351209
351231
351121
351122
520120
360279
351501
351615
351212
500379
8160002
8041053
8041058
8024062
8160003
890359
8172007
8160001
900407
8024039
8041006
351219
351271
351221
351500
360284
500177
8171004
351605
351124
351421
8197031
351321
351316
351309
351618
351619
QTY
1
2
1
1
1
2
2
2
2
1
1
2
2
1
1
1
1
5
2
4
2
9
1
1
1
2
2
1
1
1
1
1
1
1
12
1
1
1
2
1
1
1
1
1
n
QTY
1
2
1
1
1
2
2
2
2
1
1
2
2
1
1
1
1
5
2
4
2
9
1
1
1
2
2
1
1
1
1
1
1
1
12
1
1
1
2
1
1
1
1
1
ro
du
ct
io
OS901SPH
DESCRIPTION
PART NO.
FRAME SUPPORT OS900SP WA
351126
PLUG TUBE INSERT 1.25 OD
791056
HANDLE FOLDING OS900SP
351406
BUMPER RECESS
360298
BRACKET CONSOLE OS900SP
351208
GRIP HANDLE
500267
PLUG TUBE INSERT 1" OD
890132
CONTROL MAGURA OS900SP
351209
LOOP FOLDING HANDLE
351231
ENGINE BRACKET WA
351121
LINKAGE FOOT CONTROL WA
351122
PIN CLEVIS 3/8 X 2.125
520120
RETAINER 3/8" BOLT PUSH NUT
360279
LABEL INSTRUCTION OS900SP
351501
PEDAL SERVICE KIT
351615
LEVER CLUTCH/SEED DROP
351212
GRIP LEVER 0.125" X 1" X 5" ORANGE
500379
NUT LOCK 5/16"-18
8160002
SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
8041053
SCREWCAP 3/8"-16 X 3" HCS ZP
8041058
BOLT CARRIAGE 3/8"-16 X 2" ZP
8024062
LOCK NUT 3/8-16
8160003
SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F
890359
WASHER 1/4" SAE
8172007
LOCK NUT 1/4-20
8160001
TY WRAP
900407
BOLT CARRIAGE 5/16"-18 X 3/4" ZP
8024039
SCREWCAP 1/4"-20 X 1" HCS ZP
8041006
CABLE SPEED CONTROL RT
351219-S
CABLE SPEED CONTROL LFT
351271-S
CABLE CLUTCH SEEDING CONTROL
351221
LABEL LOGO OS900SP
351500
BOLT SHOULDER 3/8" X 1 1/4"
360284
LABEL CLUTCH BLADE
500177
WASHER 3/8 FC
8171004
BRACKET CONSOLE OS900SP W/LABELS
351605
RELEASE PEDAL WA
351124
SHAFT INNER PIVOT
351421
PIN COTTER 1/8" X 1" ZP
8197031
BRACKET PIN CATCH
351321
BOLT SHOULDER 3/8" DIA X 3.25 LG BLK OX
351316
SPRING PEDAL RELEASE
351309
HANDLE W/GRIP RIGHT OSSP SERVICE
351618
HANDLE W/GRIP LABEL LEFT OSSP SERVICE
351619
fo
ITEM NO.
5
28
29
30
31
32
33
34
35
50
51
52
53
56
67
70
72
93
102
107
110
113
114
115
117
128
129
131
136
137
138
140
141
142
144
194
200
201
202
204
205
206
208
209
17
Form No F082815A
OSSP Owner’s Manual
N
ot
fo
rR
ep
ro
du
ct
io
n
OSSP SEED BOX ASSEMBLY PARTS DRAWING
Part No 351520
18
Form No F082815A
OSSP Owner’s Manual
OSSP SEED BOX ASSEMBLY PARTS LIST
QTY
1
1
2
4
1
1
1
1
1
2
8
1
1
1
1
8
8
8
8
8
1
1
1
1
2
1
1
2
1
2
1
1
n
QTY
1
1
2
4
1
1
1
1
1
2
8
1
1
1
1
8
8
8
8
8
1
1
1
1
2
1
1
2
1
2
1
1
OS901SPS
PART NO.
351126
351103
351013
850232
351223
351105
351220
351222
351303
351408
351253
351265
400339
351503
791070
8041004
8172007
8160001
350346
8024039
351221
400424
350399
351505
430298
440193
8024041
8041026
8161041
8172020
351604
351616
N
ot
fo
rR
ep
ro
du
ct
io
OS901SPH
ITEM NO.
DESCRIPTION
PART NO.
5
FRAME SUPPORT OS900SP WA
351126
6
SEED BOX WA
351103
10
FRONT WHEEL 14" ASSY
351013
12
BEARING & FLANGETTE ASSY
850232
27
AXLE SEED BOX
351223
44
WHEEL PADDLE SEED WA
351105
45
PLATE SEED CONTROL OS900SP
351220
46
BRACKET CONTROL SEED RATE
351222
48
SPRING EXTENSION .5 X 5.00
351303
55
SPACER SEED BOX AXLE OS900SP
351408
63
SPACER SEED PLATE OS900SP
351253
64
DIAL SEED INDICATOR
351265
65
KNOB 5/16"-18 X 5/8" FLUTED
400339
66
LABEL SEED FLOW RATE
351503
83
CLAMP ROUTING FUEL LINE
791070
100
SCREW 1/4" - 20 X .75 HWH
8041004
115
WASHER 1/4" SAE
8172007
117
LOCK NUT 1/4-20
8160001
125
NUT 5/16"-18 SER HEX WASHER FLNG 350346
ZP
129
BOLT CARRIAGE 5/16"-18 X 3/4" ZP 8024039
138
CABLE CLUTCH SEEDING CONTROL 351221
145
LABEL WARNING OPEI
400424
147
PIN CLEVIS 1/4" X .61
350399
148
LABEL BADGING OS900SP
351505
149
WASHER LOCK 5/16" TWISTED TOOTH430298
HEAVY
150
PIN CLIP HITCH 0.051 X 3/4"
440193
151
BOLT CARRIAGE 5/16"-18 X 1 1/4" ZP 8024041
152
SCREWCAP 5/16"-18 X 3/4" HCS ZP 8041026
153
NUT LOCK 5/16"-18 LT WT TH ZP
8161041
154
WASHER FENDER 5/16"
8172020
192
SEED BOX WAS OS900SP W/LABELS 351604
207
SEED BOT SERVICE KIT
351616
Part No 351520
19
Form No F082815A
OSSP Owner’s Manual
N
ot
fo
rR
ep
ro
du
ct
io
n
OSSP TRANSMISSION ASSEMBLY PARTS DRAWING
Part No 351520
20
Form No F082815A
OSSP Owner’s Manual
OSSP TRANSMISSION ASSEMBLY PARTS LIST
OS901SPH
ITEM NO.
DESCRIPTION
OS901SPS
PART NO.
QTY
PART NO.
QTY
TRANSAXLE
351201
1
351201
1
3
ENGINE BASE WA
351125
1
351125
1
5
FRAME SUPPORT OS900SP WA
351126
1
351126
1
7
JACKSHAFT WA
351107
1
351107
1
11
REAR WHEEL13" X 5" PNEU ASSY
351202
2
351202
2
12
BEARING & FLANGETTE ASSY
850232
4
850232
4
14
BELT 3L550 TRUFLEX
351327
1
351327
1
15
PULLEY 0.75" ID X 3.50"
351325
1
351325
1
16
PULLEY 0.75" ID X 4" 4L SECTION
351210
1
351210
1
19
GUARD DRIVE BELT OS900SP
351118
1
351118
1
22
BRACKET FIXED FRONT FRAME
351226
2
351226
2
23
BRACKET RH WEAR PAD OS900SP
351227
1
351227
1
24
BRACKET LH WEAR PAD OS900SP
351228
1
351228
1
25
WEAR PAD RH OS900SP
351229
1
351229
1
26
WEAR PAD LH OS900SP
351230
1
351230
1
39
SPACER REAR WHEEL OS900SP
351409
2
351409
2
40
WASHER .765 ID X 1.25 OD X .06 THK
850238
2
850238
2
41
WASHER 1.125 OD X .344 ID X 10 GA
441150
1
441150
1
42
SPEED CONTROL ASSY
351011
1
351011
1
43
CONNECTOR SPEED CONTROL
351015
1
351015
1
59
LABEL DEPTH GAUGE OS900SP
351504
1
351504
1
60
MULE ASSY
351614
1
351614
1
61
KNOB HAND
850154
1
850154
1
62
ROD BYPASS ARM TRANSAXLE
351304
1
351304
1
75
SPACER PULLEY JACKSHAFT
351415
1
351415
1
79
BRACKET CLUTCH CABLE
351200
1
351200
1
84
LOCKNUT WA
800227
1
800227
1
85
WASHER .75"
800109
1
800109
1
86
ROD HEIGHT ADJUST SCREW
351311
1
351311
1
90
BOLT SHOULDER 3/8" X 2"
360153
2
360153
2
92
BOLT SHOULDER 3/8" X 1/2"
830528
1
830528
1
93
NUT LOCK 5/16"-18
8160002
10
8160002
10
94
RING RETAINING EXTERNAL 3/4"
95
WASHER SPLIT LOCK
97
SCREWCAP 5/16-24 X 1"
ot
fo
rR
ep
ro
du
ct
io
n
2
850230
2
850230
2
8177011
6
8177011
6
400164
2
400164
2
SCREWCAP 3/8"-16 X 1 3/4" HCS ZP
8041053
1
8041053
1
105
SCREWCAP 5/16"-18 X 3" HCS ZP
8041036
4
8041036
4
106
SCREWCAP 5/16"-18 X 2"
8041032
1
8041032
1
108
WASHER 5/16 FLAT
8171003
4
8171003
4
111
BOLT CARRIAGE 5/16"-18 X 2 3/4" ZP
8024047
4
8024047
4
113
LOCK NUT 3/8-16
8160003
4
8160003
4
114
SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F
890359
5
890359
5
115
WASHER 1/4" SAE
8172007
10
8172007
10
116
WASHER 3/8" SAE
8172009
2
8172009
2
117
LOCK NUT 1/4-20
8160001
6
8160001
6
118
NUT FLANGE 5/16-18 ZP
350346
4
350346
4
N
102
Part No 351520
21
Form No F082815A
OSSP Owner’s Manual
OSSP TRANSMISSION ASSEMBLY PARTS LIST
OS901SPH
ITEM NO.
DESCRIPTION
QTY
PART NO.
QTY
BRACKET TORQUE LIMITING
351294
1
351294
1
125
NUT 5/16"-18 SER HEX WASHER FLNG ZP
350346
7
350346
7
126
SCREW SPOT WELD 5/16"-18 X 3/4 W/PROJ
351263
4
351263
4
129
BOLT CARRIAGE 5/16"-18 X 3/4" ZP
8024039
5
8024039
5
131
SCREWCAP 1/4"-20 X 1" HCS ZP
8041006
4
8041006
4
135
KEY 3/16" SQ X 1 1/4"
9201080
1
9201080
1
136
CABLE SPEED CONTROL RT
137
CABLE SPEED CONTROL LFT
139
ro
du
ct
io
n
123
1
351219
1
351271
1
351271
1
SCREWCAP 5/16" SER HEX WSHR FLNG GR. 5 ZP
351264
8
351264
8
143
GROMMET 1.25" HOLE
520092
1
520092
1
146
LABEL DRIVE RELEASE OS900SP
351507
1
351507
1
150
PIN CLIP HITCH 0.051 X 3/4"
440193
1
440193
1
153
NUT LOCK 5/16"-18 LT WT TH ZP
8161041
1
8161041
1
154
WASHER FENDER 5/16"
8172020
1
8172020
1
155
SPRING LIFT ASSIST OS900SP
351254
2
351254
2
157
SCREW MACH #10-24 X 2" HWF ZP
8059143
1
8059143
1
159
SPACER EYELET SPEED CONTROL PM
351348
2
351348
2
160
BEARING 1/2" ID X 1.125 OD
351257
2
351257
2
161
BOLT SHOULDER 3/8" X 1 3/4"
351258
2
351258
2
162
BRACKET SPEED CONTROL WA OS900SP
351108
1
351108
1
163
BELLCRANK SPEED CONTROL WA OS900SP
351109
2
351109
2
164
CAM SPEED CONTROL WA
351110
1
351110
1
165
BUSHING PIVOT FRAME AE
360183
2
360183
2
166
BOLT SHOULDER 5/16" X 1 1/2"
500340
1
500340
1
167
SPRING EXTENSION
800242
2
800242
2
168
BUSHING 3/8" ID X 1/2" OD X 3/8"
840078
4
840078
4
169
SCREWCAP 1/4-20 X 1 3/4 SKT BUT HD
840199
2
840199
2
170
NUT LOCK 5/8"-11 LT WT TH ZP
8161046
1
8161046
1
fo
rR
ep
351219
171
WASHER 5/8" SAE
8172013
1
8172013
1
172
SCREWCAP 5/16"-18 X 1" HCS ZP
8041028
2
8041028
2
173
PULLEY IDLER 2.75" OD X 3/8" BORE
350114
1
350114
1
174
BRACKET DRIVE BELT WA OS900SP
351104
1
351104
1
175
PULLEY 3V GROOVE IDLER
351216
1
351216
1
177
BOLT SHOULDER 1/2" X 2"
520031
1
520031
1
178
ARM IDLER MULE DRIVE WA OS900SP
351120
1
351120
1
179
SPRING IDLER MULE DRIVE OS900SP
351302
1
351302
1
180
SCREWCAP 3/8"-16 X 1 1/2" HCS ZP
8041052
1
8041052
1
182
WASHER #10 SAE
8172005
1
8172005
1
183
KEY 3/16" SQ X 2 1/8"
9201087
2
9201087
2
186
SCREWCAP 5/16"-18 X 5" HCS ZP
8041042
1
8041042
1
189
KEY 3/16" SQ X 5/8"
9201072
1
9201072
1
195
FRAME SUPPORT OS900SP WA W/LABELS
351613
1
351613
1
197
DRIVE BELT GUARD WA W/LABELS
351609
1
351609
1
198
BRACKET BELT GUIDE OS900SP
351326
1
351326
1
203
RING SNAP TRUARC
850233
1
850233
1
210
SPACER STEPPED SPEED CONTROL PM
351347
2
351347
2
ot
N
Part No 351520
OS901SPS
PART NO.
22
Form No F082815A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising