ACTi | Z950 | Hardware manual | ACTi Z950 Hardware Manual

ACTi Z950 Hardware Manual
Speed Dome Camera
Hardware Manual
Z950
2019/10/05
Hardware Manual
Table of Contents
Precautions
3
Regulatory Compliance .................................................................... 4
Safety and Compliance Information ................................................ 5
Introduction
7
List of Models.................................................................................... 7
Package Contents............................................................................. 8
Physical Description ........................................................................ 8
Cable Connection ............................................................................. 9
Reset Camera to Default Settings ................................................... 9
Installation Procedures
10
Preparing for Installation ............................................................... 10
Install Memory Card (Optional)...................................................... 11
Mounting on the Wall...................................................................... 11
Waterproof RJ-45 Connector ......................................................... 14
Waterproof Tail Cable ..................................................................... 14
Access the Camera
15
2
www.acti.com
Hardware Manual
Precautions
Read these instructions
Read all the safety and operating instructions before using this product.
Heed all warnings
Adhere to all the warnings on the product and in the instruction manual. Failure to follow the
safety instructions given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
ACTi and ACTi logo are registered trademarks of ACTi Corporation. All other names and
products used in this manual are registered trademarks of their respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any
typographical or technical errors and reserves the right to make changes to the product and
manuals without prior notice.
3
www.acti.com
Hardware Manual
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the limits for digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause
undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU
and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a
responsible manner.
4
www.acti.com
Hardware Manual
Safety and Compliance Information
Installation and removal of the unit and its accessories must be carried out by qualified
personnel. You must read all of the Safety Instructions supplied with your equipment before
installation and operation.
Installation

This device is a class A product and may cause radio interference. Take measures if
necessary.

Make sure the camera operates in an environment where the temperature and humidity
meet requirements. Keep the camera from excessive pressure, vibration, moisture, dust,
and intensive electromagnetic radiation.

Use a power adapter that meets the requirements. Otherwise, the device may be
damaged.

Make sure the length of the power cable between the power adapter and the camera is not
too long, otherwise the voltage of the camera is lowered, causing the camera to work
abnormally. If it is required to lengthen the power cable, lengthen the cable between the
power adapter and the mains.

Do not hold the tail cable by hand for weight bearing. Otherwise, the cable connector of the
camera could be loosened.

Do not cut the tail cable. Exposed tail cables may cause short circuit and damage the
camera.

When connecting to an external interface, use an existing connection terminal, and ensure
that the cable terminal (latch or clamp) is in good condition and properly fastened. Ensure
that the cable is not tense during mounting, with a proper margin reserved to avoid poor
port contact or loosening caused by shock or shake.

The end of the tail cable must be kept under good protection. Take waterproof measures to
protect the tail cable.

During the process of transportation, special attention is required for the protection of the
transparent dome cover to prevent friction, scratch and contamination, etc. In order to
keep the cover clean, do not remove the protective film on the cover during mounting. After
mounting is finished, remove the film before the device is powered on.

Contact professionals for maintenance information. Do not attempt to dismantle the device
by yourself. We shall not assume any responsibility for problems caused by unauthorized
repair or maintenance.
5
www.acti.com
Hardware Manual
Maintenance

If there is dust on the front glass surface, remove the dust gently using an oil-free brush or
a rubber dust blowing ball.

If there is grease or a dust stain on the front glass surface, clean the glass surface gently
from the center outward using anti-static gloves or an oil-free cloth. If the grease or the
stain still cannot be removed, use anti-static gloves or an oil-free cloth dipped with
detergent and clean the glass surface gently until it is removed.

Do not use organic solvents, such as benzene or ethanol when cleaning the transparent
dome cover.

Never look at the transmit laser while the power is on. Never look
directly at the fiber ports and the fiber cable ends when they are
powered on.

Use of controls or adjustments to the performance or procedures
other than those specified herein may result in hazardous laser
emissions.
6
www.acti.com
Hardware Manual
Introduction
List of Models
This hardware manual contains the following models:
Z950
2MP Outdoor Speed Dome with D/N, Adaptive IR, Extreme
WDR, SLLS, 20x Zoom Lens
7
www.acti.com
Hardware Manual
Package Contents
Contact your local dealer if the package is damaged or incomplete. The attachments may vary
with models, please see the actual model for details.

Camera

AC24 Power Adapter

Quick Installation Guide

Accessory Pack

Bracket Adapter Ring

Cable Gland
Physical Description
8
www.acti.com
Hardware Manual
Cable Connection
All the cables are tagged to indicate their functions. This section takes the full pigtail cable as
an example. You can connect cables by referring to the following figure.
Display
device
1
2
Audio input
(Sound pickup)
9
3
5
4
Alarm input (Voice
activated switch)
Alarm output
(Alarm indicator)
6 7 8
Third-party device
connected through
RS485 interface
Ground
Power adapter
Network access
device connected
through optical
interface
Audio output
(Outdoor
sound box)
Network access
device connected
through copper
interface
NOTE:

Please disconnect the power before mounting the camera.

For specifications, see the latest product datasheets.
Reset Camera to Default Settings
Remove the back cover first. Press and hold the RST button for about 15 seconds to restore
factory default settings. The RST button only works within ten minutes after the camera is
powered on.
9
www.acti.com
Hardware Manual
Installation Procedures
Preparing for Installation
The following figures are for reference only. See the actual product for details.
Before mounting the camera, check the device model, accessory types and quantities against
the packing list to ensure the components are complete.
Bracket
adpater
Tail
cable
Safety
wire
Dome
Verify the bearing capacity of the mounted position
Verify that the mounted position meets the bearing requirements. Otherwise, you are advised
to reinforce the mounted position for the device weight. For more information, see the product
datasheet.
Verify the lightning protection and grounding requirements

Select proper lightning protection devices for the power supply, audio and video signals
interfaces, and RS485 interfaces.

See Error! Reference source not found. to ground the terminal properly.
Cable Requirements
10M/100M Ethernet CAT 5/5E UTP cables are applicable to the ANSI/EIA/TIA-568A/B and
ISO/D.
Eight wires in the network cable need to be inserted in parallel into the top of the cable
connector. The cable connector needs to be crimped in position. When the cable connector is
in position, ensure that the metal pieces of the cable connector are parallel to each other and
the clamp of the cable connector is intact.
10
www.acti.com
Hardware Manual
Install Memory Card (Optional)
Install the memory card first, then format the card in the software interface before use.
Disconnect the camera from the power before installation, otherwise the camera or the
memory card may be damaged.
1. Unscrew the four cross-recessed screws to remove the back cover.
2. Insert the memory card in Slot 1 as indicated on the figure below.
Slot 1
1
2
Slot 2
Screw
Micro SD card
Slot 3
Back cover
3. Attach the back cover.
4. Properly mount the waterproof ring in position.
Mounting on the Wall
1. Mark the positions of the holes by referring to the mount points of the bracket and lead the
cable through the hole on the wall. Then drill holes and knock the expansion bolts.
11
www.acti.com
Hardware Manual
2. Turn the bracket adapter (G1 ½ male thread) in and secure the bracket adapter with a
screw.
3. Attach the safety wire to the bracket and the dome. And Lead the tail cable through the
bracket.
4. Attach the dome to the bracket adapter.
Slide camera holders into inner track and turn camera till it is blocked by bracket adapter
screw.
Bracket
adapter
screw
Inner
track
Camera
holder
12
www.acti.com
Hardware Manual
5. Secure the dome with two M5 screws.
M5
screw
6. Connect the cables and attach the bracket to the wall with flat pads, washers and nuts.
NOTE:

When mounting the camera, install the bracket adapter to the bracket first and
then mount the camera to the bracket.

Tighten all the screws to hold the camera securely.

For waterproofing, apply sealant between the camera and the bracket, wall
veneer slits, and leading-out holes of the wall.

The above installation describes concealed installation. To implement open
installation, directly lead the cable out from the cable slot on the bracket.
13
www.acti.com
Hardware Manual
Waterproof RJ-45 Connector
Seal ring 3
2 1
Attach the seal ring to the Ethernet interface. Mount
the waterproof components in order. Then insert the
cable into the Ethernet interface and screw the
Insert in order
waterproof bolt in.
NOTE: You can crimp the inner wires of the cable with the RJ45 plug first and then cover the
waterproof components. You may also cover the waterproof components first.
Waterproof Tail Cable
Connect the tail cables and then take the following steps to protect the tail cables from water
using waterproof tapes. The figures are for your reference only.
Connect the tail cables, and protect the cables and cable
connections using insulating tapes. Then wrap all the tail
cables together using insulating tapes.
Choose a start point for waterproof tapes and protect the
tail cables using waterproof tapes.
NOTE:

Avoid short circuit when insulating the cables.

Use self adhesive waterproof tapes that will stick together with the twisted cables.

Tighten waterproof tapes when wrapping the cables and make sure the cable connections
are fully covered.

You are recommended to put the waterproof cables in a waterproof junction box which
needs to be purchased separately.
14
www.acti.com
Hardware Manual
Access the Camera
Before you begin, check that:

Your camera is operating properly and connected to the network.

The PC you are using is installed with Internet Explorer 11.
Follow these steps to access your camera through the Web:
1. Open your browser, input the IP address of your camera in the address bar and then press
Enter to open the login page.
2. Enter the username and password and then click Login.
The factory default Account and Password of the camera:
Account: Admin
Password: 123456
NOTE:

Install the ActiveX at your first login. When the installation of the ActiveX is completed,
open your IE to log in.

For your first login with Windows 7, if the system does not prompt you to install ActiveX,
follow these steps to turn off UAC: click the Start button, and then click Control Panel. In
the search box, type uac, and then click Change User Account Control Settings. Move
the slider to the Never Notify position, and then click OK. After UAC is turned off, log in
again.

If the installation failed, open Internet Option in IE before login. Click the Security tab,
click Trusted sites, and then click Sites to add the website. If you use Windows 7, you
need to save the setup.exe to your PC first, and then right-click the file, select Run as
administrator, and then install it according to instructions.
15
www.acti.com
Copyright © 2018, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C.
TEL : +886-2-2656-2588
FAX : +886-2-2656-2599
Email: sales@acti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising