ACTi | Q960 Q961 Q962 | Installation guide | ACTi Q960 Q961 Q962 Installation Guide

ACTi Q960 Q961 Q962 Installation Guide
People Counting Camera
Installation Guide
Q960, Q961, Q962
2019/08/02
INSTALLATION GUIDE
The following documentation covers the installation and configuration of your
device.
NOTE: The accuracy of the analytics algorithm may be affected by different
environmental factors or inappropriate installation. Please follow the
procedures in this installation guide. ACTi will not be held liable for
inaccuracies resulting from the aforesaid causes.
Part 1: Installation Specification
1. Model and counting width
The counting width depends on the installation height. The recommended
installation height for dual-lens camera is less than 4.0m (13.1ft). The specific
corresponding relation shown below:
Model
Q960
Q961
Q962
Installation
height
Max. counting
width
Without
(m/ft)
(m/ft)
doorframe
2.5/8.2
1.8/5.9
Placed in the middle
3.0/9.8
2.9/9.5
Placed in the middle
3.5/11.5
4.0/13.1
Placed in the middle
3.0/9.8
2.2/7.2
Placed in the middle
3.5/11.5
3.1/10.2
Placed in the middle
4.0/13.1
4.0/13.1
Placed in the middle
4.0/13.1
2.8/9.2
Placed in the middle
4.5/14.8
3.4/11.2
Placed in the middle
5.0/16.4
4.0/13.1
Placed in the middle
With doorframe
0.68m(2.2ft) to door
Placed in the middle
1.1m(3.6ft) to door
Placed in the middle
1.52m(5.0ft) to door
Placed in the middle
0.85m(2.8ft) to door
Placed in the middle
1.17m(3.8ft) to door
Placed in the middle
1.5m(4.9ft) to door
Placed in the middle
1.05m(3.4ft) to door
Placed in the middle
1.28m(4.2ft) to door
Placed in the middle
1.5m(4.9ft) to door
2
Placed in the middle
www.acti.com
INSTALLATION GUIDE
2.
Package Contents
Camera
Mounting Base
Quick Start Guide
Screw Kit
Quick Start
Guide
3
www.acti.com
INSTALLATION GUIDE
Part 2: Installation Steps
1. Installation
Please pay great attention to the mounting position. Inappropriate mounting
position may cause loss of accuracy. The recommended mounting position is
shown below:
Vertical sketch map of mounting position
Horizontal sketch map of mounting position
Effect picture after installation
Notice: Avoid the reflective environment (ex: Marble floor)
4
www.acti.com
INSTALLATION GUIDE
Make sure the camera is mounted vertically above the passenger flow
(90°vertical by the ground), see picture below:
Passenger flow(perpendicular to the door)
For some scenarios where there are multiple cameras, mount the cameras
according to two rules.

Rule one: If there are turnstiles, each camera should be mounted to monitor
certain turnstile
5
www.acti.com
INSTALLATION GUIDE

Rule two: If there is no turnstile, at first, mount the cameras in one line, and
make sure the cameras have the same focal length. Then, keep a proper
distance between each camera according to the overlap (see the yellow
area below) of the adjacent two cameras’ counting width. The suggested
overlapping length is between 0.2-0.5m.
Sketch map of multiple cameras installation
Notice:
1)
People flow should be in vertical up-and-down direction
Passenger flow in horizontal direction (wrong)
6
www.acti.com
INSTALLATION GUIDE
Passenger flow in slant direction (wrong)
Passenger flow in vertical up-and-down direction (right)
2)
Passageway width should be within camera’s counting width
3) Avoid obstacles such glass door, shield door and turnstile that block the
camera. For Each divided passageway, mount one camera right above.
7
www.acti.com
INSTALLATION GUIDE
4) The camera should be mounted as close as possible to the passageway
without obstacle. Remove the obstacle or adjust the camera mounting position if
there is obstacle below the camera. Meanwhile, to prevent miscounting, if there’s
a sliding door onsite, make sure the trajectory of the sliding door does not
overlap the detection line. Otherwise, the counting number may be misled by the
door opening and closing
Too far away from the door / Obstacle below camera
Recommended installation
8
www.acti.com
INSTALLATION GUIDE
2.
Configuration for single camera
Step 1: Enable People Counting: check [Configuration]-[People Counting]
-[Enable People Counting]
Step 2: Calibration- Select the green box, drag it to proper location and click
[Calibration]. After this, “Height” in the configuration page will refresh (close
to the real height). A red box, which means the counting scope, and yellow
detection line will turn up. The arrow shows the direction of entering. See
picture below:
Notice: If auto calibration fails, switch to [Manual] and input the measured “Height”,
then click [Calibration].
Step 3: Detection line: move the detection line to proper location, about 0.5m
to the door. Then adjust the length of detection line to the real door’s width by
dragging the detection line’s two ends. See picture below:
Notice: You should make the whole detection line in the same ground level or it may
lose accuracy.
9
www.acti.com
INSTALLATION GUIDE
Step 4: Save configuration and test. After configuration, click [save] and test.
If miscounting happens, slightly adjust the detection line’s location and
length.
3.
Configuration for multiple cameras
Step 1: Do configuration for each camera following the steps above
Step 2: Move each camera’s detection line and connect the ends of adjacent
lines. Some objects could be placed on the image border for reference. See
picture below:
Configuration of each detection line
10
www.acti.com
INSTALLATION GUIDE
Part 3: Application Scenario
The application scenario and the mounting position are very important to the
people counting accuracy. Usually the camera is mounted above the
passageway and the door. Below shows the mounting position and
configuration for two typical examples:
Mounting position and configuration for supermarket
Mounting position and configuration for subway
11
www.acti.com
Copyright © 2019, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan
114, R.O.C.
TEL : +886-2-2656-2588
FAX : +886-2-2656-2599
Email: sales@acti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising