ACTi | Outdoor PTZ / Speed Dome (I9x) on Straight Wall with Accessory Sets of PMAX-0305 | Installation guide | ACTi Outdoor PTZ / Speed Dome (I9x) on Straight Wall with Accessory Sets of PMAX-0305 Installation Guide

ACTi Outdoor PTZ / Speed Dome (I9x) on Straight Wall with Accessory Sets of PMAX-0305 Installation Guide
Outdoor PTZ
Mounting on the Wall
Using Accessory Sets
Installation Guide
For Models:
I93, I94, I95, I96, KCM-8211
2013/12/09
Installation Guide
Table of Contents
Mounting Accessory Set Solutions .................................. 3
Heavy Duty Wall Mount Installation Procedures ............. 4
Step 1: Unpack the Camera ...................................................................... 4
Step 2: Install the Heavy Duty Wall Mount ............................................... 6
Optional: Add Extension Tube ................................................................. 6
Step 3: Install the Camera ......................................................................... 7
Step 4: Connect the Cables ...................................................................... 9
How to Waterproof the Cable Using the Cable Gland ........................... 10
How to Waterproof the Cable Using the Conduit Gland ........................ 14
Heavy Duty Wall Mount with Junction Box
Installation Procedures ................................................... 18
Step 1: Unpack the Camera .................................................................... 19
Step 2: Unpack the Junction Box ........................................................... 20
Step 3: Drill the Holes on the Wall .......................................................... 21
Step 4: Waterproof the Cables ................................................................ 21
Step 5: Install the Junction Box ............................................................. 23
Step 6: Install the Heavy Duty Wall Mount ............................................. 24
Optional: Add Extension Tube ............................................................... 24
Step 7: Install the Camera ....................................................................... 25
Step 8: Connect the Cables .................................................................... 26
Appendices ....................................................................... 28
How to Install Extension Tubes .............................................................. 28
How to Use the Power Adapter (For I9x Models) .................................. 29
How to Attach the Safety Wire Strap (For I9x Models) ......................... 30
Safety Information ............................................................ 32
2
www.acti.com
Installation Guide
Mounting Accessory Set Solutions
If the camera will be installed on a straight wall, consider the following options:
Mounting Solution
Heavy Duty Wall
Cabling Solution
Cables go through the wall.
Must Drill a Hole
on the Wall
Yes
Mount
PMAX- 0305
Heavy Duty Wall
Mount with Junction
Box
The cables and the bundled power
adapter are hosted inside the junction
box. The cables go out the junction box
Yes / No
enclosed in a flexible conduit. The flex
conduit can pass through the wall or be
routed along the wall.
PMAX-00305
PMAX-0700
3
www.acti.com
Installation Guide
Heavy Duty Wall Mount Installation
Procedures
Perform the following procedures to install the camera on a straight wall using the heavy duty wall
mount with cables passing through the wall. You must be able to access the other side of the wall
to complete the cable connections.
The bundled power adapter and power cord, approximately 200 cm in length, are not waterproof
and must be protected indoors. Therefore with this type of installation, it is recommended to use a
high PoE injector (purchased separately) to connect the camera to the power outlet and the
network.
Before installation, prepare the tools and equipment which are not supplied with the mounting
accessory:

Exterior-grade Ethernet Cables

High Power-over-Ethernet (PoE) Injector

Waterproof Tape
Step 1: Unpack the Camera
NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended to retain
the plastic covering the dome cover until the camera is completely installed.
1. Loosen the four screws using the bundled Allen
wrench.
4
www.acti.com
Installation Guide
2. Carefully lift the camera cover and place it aside.
NOTE: The cover is attached to the camera by a
metallic wire; do not abruptly lift the cover.
3. Remove the outer and inner Styrofoam.
Outer Styrofoam
Inner Styrofoam
4. Attach the camera cover.
Align the cover screws to the screw holes on the
camera (as marked on the illustration) and secure the
screws using the bundled Allen wrench.
5
www.acti.com
Installation Guide
Step 2: Install the Heavy Duty Wall Mount
NOTE: Before installation, make sure that the wall can bear more than the total weight of the
camera and the mounting accessories.
1. Using the drill template (included in the heavy duty wall mount package), mark and drill the
screw holes and the conduit hole location on the wall. The conduit hole is where the cables
will pass through the wall.
2. Attach the heavy duty wall mount onto the wall using four (4) screws (purchased separately).
Optional: Add Extension Tube
If the heavy duty wall mount is not long enough, add one extension tube (purchased separately).
See How to Install Extension Tubes on page 28.
6
www.acti.com
Installation Guide
Step 3: Install the Camera
1. Insert the camera cables through the heavy duty wall mount, extension tube (if any), and
through the conduit hole on the wall.
2. Align the slot on the camera to the tab inside the heavy duty wall mount and insert the top of
the camera.
3. Twist the camera to align the screw holes and attach the two (2) mounting screws (included
in the camera package).
4. For I9x models, attach the safety wire strap for added protection; see How to Attach the
Safety Wire Strap (For I9x Models) on page 30.
5. Remove the plastic covering the dome cover.
7
www.acti.com
Installation Guide
Below is a sample installation.
8
www.acti.com
Installation Guide
Step 4: Connect the Cables
The camera itself is waterproof, however take note that the cable connections are not.
If the camera is mounted directly on the wall where the cables pass through the wall, then your
installation is complete and you do not need to waterproof the cable connections.
However, if the camera is mounted where the cables may be exposed then it is recommended to
waterproof the cable connections or use a junction box.
The camera comes with a Cable Gland and Conduit Gland. It is recommended to use one of
these glands when a high PoE injector will be used with the camera. However, if the bundled
power adapter will be used or digital input/output devices will be connected, it is recommended to
house the cables inside the junction box (see Heavy Duty Wall Mount with Junction Box
Installation Procedures on page 18).
Determine the type of waterproof solution applicable to your installation environment
requirements and prepare the necessary accessories or purchase extra materials.
Cable Gland
Conduit Gland
For use with an exterior-grade Ethernet cable
For use with 1/2” flexible conduit (not included
(not included in the package).
in the package).
See How to Waterproof the Cable Using
See How to Waterproof the Cable Using
the Cable Gland on page 10.
the Conduit Gland on page 14.
9
www.acti.com
Installation Guide
How to Waterproof the Cable Using the Cable Gland
1. Prepare the following items:
Cable Gland
Exterior-Grade
Ethernet Cable
Waterproof Tape
NOTE: Not included
in the camera
package.
NOTE: Not included
in the camera
package.
Gland Rubber Ring
Washer
NOTE: The washer will
not be used in this
installation, please set it
aside.
2. Detach the cable gland as shown below.
Gland Body
Clamping Nut
Sealing Rubber and Claw
3. Insert the clamping nut through the Ethernet cable.
10
www.acti.com
Installation Guide
4. Insert the Ethernet cable through the sealing rubber and claw.
5. Attach one (1) supplied rubber ring on the gland body (smooth end).
NOTE: Make sure the rubber ring is completely aligned on the gap on the gland body.
6. Attach the gland body to the Ethernet port of the camera.
IMPORTANT!
Make sure the rubber ring is completely aligned and flat on the gland body to avoid
possible water leakage.
11
www.acti.com
Installation Guide
7. Connect the Ethernet connector to the Ethernet port of the camera.
8. Insert the sealing rubber and claw into the cable gland body.
9. Attach the clamping nut to the cable gland body. Make sure the clamping nut is tightly
secured and the rubber is squeezed in to avoid water leakage.
12
www.acti.com
Installation Guide
10. If necessary, connect the colored wires to digital input or output (DI/DO) devices to trigger
events or notifications. Make sure to waterproof the cable connection (e.g. wrap with
waterproof tape).
NOTE: Follow the wiring instructions described in the Camera Hardware Manual
downloadable from the website (www.acti.com).
11. Arrange all unused cables and wrap them with the waterproof tape.
NOTE:

Different applications and installation environments require different types of
waterproofing methods which may not be covered in this manual. Check your
installation environment and adapt a suitable waterproofing method.

If the camera is installed outdoors and the bundled power adapter is used or
input/output devices are connected, be sure to protect them from different
environmental factors. It is recommended to place the cable connections indoors or
housed them inside a junction box (see Heavy Duty Wall Mount with Junction Box
Installation Procedures on page 18).
DISCLAIMER:
ACTi will not be responsible for camera damage caused by improper use
of the power adapter.
13
www.acti.com
Installation Guide
How to Waterproof the Cable Using the Conduit Gland
1. Prepare the following items:
Cable Gland
1/2” Flexible Conduit
Gland Rubber Ring
Waterproof Tape
Washer
NOTE: The washer
will not be used in this
installation, please set
it aside.
NOTE: Not included
in the camera
package.
NOTE: Not included in
the camera package.
2. Detach the conduit gland as shown below.
Gland Body
Clamping Nut
Sealing Rubber
3. Insert the Ethernet cable through the flexible conduit. Then insert the clamping nut through
the flexible conduit.
14
www.acti.com
Installation Guide
4. Insert the sealing rubber and attach it at the end of the flexible conduit.
5. Attach one (1) supplied rubber ring on the gland body (smooth end).
NOTE: Make sure the rubber ring is completely aligned on the gap on the gland body.
6. Attach the gland body to the Ethernet port of the camera.
IMPORTANT!
Make sure the rubber ring is completely aligned and flat on the gland body to avoid
possible water leakage.
15
www.acti.com
Installation Guide
7. Connect the Ethernet connector to the Ethernet port of the camera.
8. Insert the sealing rubber into the conduit gland body.
9. Attach the clamping nut to the conduit gland body. Make sure the clamping nut is tightly
secured to avoid water leakage.
16
www.acti.com
Installation Guide
10. If necessary, connect the colored wires to digital input or output (DI/DO) devices to trigger
events or notifications.
NOTE: Follow the wiring instructions described in the Camera Hardware Manual
downloadable from the website (www.acti.com).
11. Arrange all unused cables and wrap them with the waterproof tape.
NOTE:

Different applications and installation environments require different types of
waterproofing methods which may not be covered in this manual. Check your
installation environment and adapt a suitable waterproofing method.

If the camera is installed outdoors and the bundled power adapter is used or
input/output devices are connected, be sure to protect them from different
environmental factors. It is recommended to place the cable connections indoors or
housed them inside a junction box (see Heavy Duty Wall Mount with Junction Box
Installation Procedures on page 18).
DISCLAIMER:
ACTi will not be responsible for camera damage caused by improper use
of the power adapter.
17
www.acti.com
Installation Guide
Heavy Duty Wall Mount with Junction
Box Installation Procedures
Perform the following procedures to install the camera on a straight wall using the heavy duty wall
mount with a junction box. Cables can be routed to pass through the wall or along the wall and
into the junction box.
This type of installation is ideal when using the bundled power adapter and power cord to ensure
they are protected from different types of weather conditions.
Before installation, prepare the tools and equipment which are not supplied with the mounting
accessory:

Ethernet Cables

Flexible Conduit with Conduit Gland (Size 3/4”)
NOTE: Below is an example of a common conduit gland with flex conduit available in the
market. Actual items sold in your area may vary.
Sealing
insert
Gland
3/4" Size
Clamping Nut
Flexible Conduit
3/4" Size
For use with the bundled power adapter and power cord, prepare also the following equipment:

Female-type Socket

Male-type Plug

Power Cable without connectors (length depends on the distance of the power supply
outlet and installation site)

Electrical tape
18
www.acti.com
Installation Guide
Step 1: Unpack the Camera
NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended to retain
the plastic covering the dome cover until the camera is completely installed.
1. Loosen the four screws using the bundled Allen
wrench.
2. Carefully lift the camera cover and place it aside.
NOTE: The cover is attached to the camera by a
metallic wire; do not abruptly lift the cover.
3. Remove the outer and inner Styrofoam.
Outer Styrofoam
Inner Styrofoam
19
www.acti.com
Installation Guide
4. Attach the camera cover.
Align the cover screws to the screw holes on the
camera (as marked on the illustration) and secure the
screws using the bundled Allen wrench.
Step 2: Unpack the Junction Box
1. Determine how the cables will be routed:

If the cables will pass through a hole on the wall, remove one or two of the rear
metal cap(s) as needed.

If the cables will go along the wall, remove one or two side metal cap(s).
or
Rear Side Metal Caps
Side Metal Caps
2. Remove the four (4) screws securing the side door.
20
www.acti.com
Installation Guide
Step 3: Drill the Holes on the Wall
NOTE: Before installation, make sure that the wall can bear more than the total weight of the
camera and the mounting accessories.
Using the drill template (included in the junction box package), mark and drill the locations of the
screw holes and one or two conduit holes (as needed) on the wall. The conduit hole is where the
cables will pass through the wall.
Step 4: Waterproof the Cables
1. Insert the cables, such as the network cable, power cable without connectors (if using the
bundled power adapter and power cord), etc., through a flexible conduit (not included in the
package).
NOTE: Only a power cable fits through the conduit hole of the junction box; thus the
installation of a power outlet to the power cable must be done inside the junction box.
Conduit Gland Body:
Attach to the Junction Box
21
www.acti.com
Installation Guide
2. If the cables will pass through the wall, attach the conduit gland body to one of the rear
holes of the junction box. If cables will be routed along the wall, skip to Step 5: Install the
Junction Box on page 23.
3. Insert the cables through the hole and tightly attach the clamping nut to the conduit gland
body.
CAUTION: Make sure the clamping nut is securely attached to the conduit gland body
to avoid water leak, etc.
DISCLAIMER: The manufacturer will not be responsible for damage caused by water leak
from incorrect cabling methods.
22
www.acti.com
Installation Guide
Step 5: Install the Junction Box
1. Attach the junction box onto the wall using four (4) screws (purchased separately).
NOTE: Make sure the junction box is tightly screwed on the wall to avoid possible shifting of
the junction box position due to the PTZ camera movements.
2. If the cables pass through the wall, skip to Step 6: Install the Heavy Duty Wall Mount 24.
If the cables will be routed along the wall, attach the conduit gland body to one of the side
holes of the junction box.
23
www.acti.com
Installation Guide
3. Insert the cables into the side hole and tightly attach the clamping nut to the conduit gland
body.
CAUTION: Make sure the clamping nut is securely attached to the conduit gland body
to avoid water leak, etc.
DISCLAIMER: The manufacturer will not be responsible for damage caused by water leak
from incorrect cabling methods.
Step 6: Install the Heavy Duty Wall Mount
Attach the heavy duty wall mount to the junction box using the four (4) screws included in the wall
mount package.
Optional: Add Extension Tube
If the heavy duty wall mount is not long enough, add one extension tube (purchased separately).
See How to Install Extension Tubes on page 28.
24
www.acti.com
Installation Guide
Step 7: Install the Camera
1. Insert the camera cables through the heavy duty wall mount, extension tube (if any), and into
the junction box.
2. Align the slot on the camera to the tab inside the heavy duty wall mount and insert the top of
the camera.
3. Twist the camera to align the screw holes and attach the two (2) mounting screws (included
in the camera package).
4. For I9x models, attach the safety wire strap for added protection; see How to Attach the
Safety Wire Strap (For I9x Models) on page 30.
5. Remove the plastic covering the dome cover.
25
www.acti.com
Installation Guide
Below is a sample installation.
Step 8: Connect the Cables
Inside the junction box, perform the following:
1. Connect the bundled power adapter and power cord and place them inside the junction box.
For I9x models, see How to Use the Power Adapter (For I9x Models) on page 29 for more
information on using the power adapter.
2. Connect the Ethernet cable from the network side to the Ethernet port of the camera.
26
www.acti.com
Installation Guide
3. If necessary, connect the colored wires to digital input or output (DI/DO) devices to trigger
events or notifications.
NOTE: Follow the wiring instructions described in the Camera Hardware Manual
downloadable from the website (www.acti.com).
4. Attach the female-type socket to the power cable in the junction box, and connect the power
cord to the socket.
NOTE:

Only a power cable fits through the conduit hole of the junction box; thus the
installation of a power outlet to the power line cable must be done inside the junction
box.

Use only the supplied power adapter and power cord that came with the camera or
the optional High PoE Injector (PPOE-0110). Using other accessories not approved
by the manufacturer may cause damage to the equipment.
5. Close the junction box door using the four (4) screws supplied with the junction box.
NOTE: Make sure the side is door is tightly sealed to ensure water does not enter the junction
box.
6. On the network side, connect the other end of the Ethernet cable to a network switch.
7. On the power supply side, attach the male-type plug on the other end of the power cable, and
then connect it to a power outlet.
27
www.acti.com
Installation Guide
Appendices
How to Install Extension Tubes
If the mounting accessory is not long enough, add one extension tube (purchased separately).
NOTE: Do not attach more than one extension tube.
1. Remove the two (2) pre-installed screws on the extension tube.
2. Align the slot on the extension tube to the tab inside the mounting accessory and install the
extension tube.
3. Twist the extension tube to align the screw holes and reattach the two (2) mounting screws
removed from step 1.
28
www.acti.com
Installation Guide
How to Use the Power Adapter (For I9x Models)
1. Slide the voltage switch to set the adapter voltage according to the voltage standard in your
location.
2. Connect the power cord to the power adapter.
1
2
3. Connect the power connector of the camera to the cable connector of the adapter.
Camera Side
Power Adapter
Side
29
www.acti.com
Installation Guide
How to Attach the Safety Wire Strap (For I9x Models)
Most of ACTi’s mounting accessories have a safety screw where the bundled safety wire strap
can be used as additional protection to avoid dropping the camera while mounted on the high
ceilings, etc.
To attach the safety wire strap, do the following:
1. Using a screwdriver, remove the screw on top of the camera.
2. Insert the screw through the smaller end of the safety wire strap and attach it to the camera.
3. Remove the safety screw from the mounting solution (below is an example of the straight
tube).
30
www.acti.com
Installation Guide
4. Align the bigger end of the safety wire strap on the mounting solution and then tightly attach
the screw to lock the safety wire strap in place.
31
www.acti.com
Installation Guide
Safety Information
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Do not use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself. Refer all servicing to qualified service
personnel.
32
www.acti.com
Installation Guide
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the inner parts of video product have been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
33
www.acti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising