ACTi | NVR 3 Quick | Installation guide | ACTi NVR 3 Quick Installation Guide

ACTi NVR 3 Quick Installation Guide
ACTi NVR 3.0
Quick Installation Guide
Step 2
ACCESS VIA BROWSER
Wait for a few seconds
before the server is
ready. Connect to
http://localhost/ via
Internet Explorer.
BEFORE YOU START
Thank you for using ACTi NVR 3.0 server system. This
guide will demonstrate the fundamentals of how to
setup this server system. For detailed instructions,
please refer to ACTi NVR 3.0 System Administrator’s
Manual ,available at http://www.acti.com/nvr3
The pre-requisites below are necessary for installation:
 Ensure that your server computer meets the
minimum system requirements.
 Uninstall previous ACTi NVR 2.X product from the
server computer.
 Disable UAC function in Windows.
 Make sure there is more than 20 GB disk space in
your C drive.
Install two ACTi
ActiveX control
components.
Step 3
LOGIN
On Login page, enter:
●Account: Admin
●Password: 123456
Step 1
INSTALL THE SERVER
Click “Login”.
Execute and install shield
application . Follow the
onscreen instructions to
complete the installation.
If you meet the following problems, please refer to the chapters
mentioned below in ACTi NVR 3.0 System Administrator’s
Manual :
1. Cannot access Login page
(1) Server is not ready, please wait for a while and connect
again.
(2) Port 80 is currently occupied by another application, please
close that application.  Login Failure Troubleshooting
2. Cannot install the ActiveX control
(1) Use Internet Explorer browser 32-bit version.
(2) The UAC function in Windows Vista/7 or bans on the
installation of add-ons. Please turn off the UAC function.
 Turn off Windows UAC Function
(3) Internet Explorer security settings restrict the installation of
add-on components. Please adjust the browser settings.
 Login Failure Troubleshooting
SETUP WIZARD
Step 5
ADD DEVICES
Note
On NVR screen,
(1) Click the Setup
button.
2
1
(2) Select “Device”.
(3) On Setup
pageDevice tab,
click “Add Device”.
3
Step 4
Setup Wizard will guide you through the setup
procedures. You may configure these settings on NVR
Setup page later after this wizard.
(4) Select a search
method based on
network
environment.
4
1
Step 5
ADD DEVICES (continued)
Step 6
CREATE USERS
Go to Setup page Users tab.
●Create a User Group
(1) Select “User Groups”, click “Add”.
(2) Enter group ID and click “Apply”.
(3) Configure user group permissions and click “Apply”.
1
● Select “Search
Devices” to autosearch the local
network for ACTi
devices. Select your
devices and click
“Apply”.
2
● Select “Search
ONVIF Devices” to
auto-search the
local network for
ONVIF-compliant
devices. Fill in the
device’s credentials
then click
.
Select your devices
and click “Apply”.
3
●Create a User Account
(4) Select “Users”, click “Add”.
(5) Enter user Account, Password and select User
Group, and click “Apply”.
● Select “Add Device
41
Manually” to add
devices cross-LAN or
WAN. Fill in the
fields Media Type,
Protocol, IP Address,
HTTP Port, Account
& Password. Click
“Get Device Settings”
then “Apply”.
5
Step 7
SET RECORDING SCHEDULE
Go to Setup page Schedule tab.
(1) Select the device on Device List.
(2) Choose recording mode:
(3)Drag on
timetable.
4
1
or
2
(4) Click
“Apply”.
Step 9
CUSTOMIZE VIEWS
Go to Live View page.
(1) On View Tool bar, click
to create a new layout,
then click
to enter edit mode.
(2) Select a layout style.
(3) ●To add a camera view:
Pull a device from Device List to a channel.
●To add a map view:
Select a channel and click
, upload the map,
drag the lower right corner to adjust map size.
(4) On View Tool bar, click
to save the view.
(5) Click
to set this view as default live view.
3
View Tool bar
2
Step 8
CAMERA SETTINGS
Go to Setup page Device tab
(1) Select the device on Device List.
(2) Enter Basic/Video/PTZ/Preset Tour tabs for settings.
2
1
1
4 5
3
VALIDATION
Step 10
(1) To check live streaming, go to Live View page, select
certain view from View List or a camera from Device
List.
(2) To check recording, go to Playback page, select
certain view from View List or a camera from Device
List. Drag on the time bar to see the recorded video.
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising