American Hearth | Vented/Vent-Free Slope Glaze Burners (VFSR, VFSM) | Owner Manual | White Mountain Hearth Vented/Vent-Free Slope Glaze Burners (VFSR, VFSM) Owner Manual

White Mountain Hearth Vented/Vent-Free Slope Glaze Burners (VFSR, VFSM) Owner Manual
INSTALLATION INSTRUCTIONS
AND OWNER’S MANUAL
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
UNVENTED AND VENTED
GAS LOG BURNERS AND
DECORATIVE APPLIANCES
GAS-FIRED
MODELS:
VFSR-(16,18,24,30)-4
VFSM-(18,24,30)-3
WARNING
FIRE OR EXPLOSION HAZARD
If the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas
supplier, call the fire department.
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
MH-46389
WARNING
If not installed, operated and maintained in
accordance with the manufacturer's instructions,
this product could expose you to substances in
fuel or from fuel combustion which can cause
death or serious illness.
This is an unvented gas-fired heater. It
uses air (oxygen) from the room in which
it is installed. Provisions for adequate
combustion and ventilation air must be
provided. Refer to page 12.
This appliance may be installed in an after-market
permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases.
Water Vapor: A By-Product of
Unvented Room Heaters
Water vapor is a by-product of gas combustion. An unvented room heater produces
approximately one (1) ounce (30ml) of water
for every 1,000 BTU's (.3KW's) of gas input
per hour. Refer to page 11.
Page 1
BEFORE YOU START
1.
2.
Read the safety information on Pages 7 to 9.
If located in the Commonwealth of Massachusetts, please
note the special requirements on page 11.
Where are you going to install the fireplace? See pages 13
to 15.
Install the gas lines. See page 17.
3.
4.
5.
6.
Install the wiring. See page 23.
Light the burner and troubleshoot. See pages 19 to 21 and
24.
Installer must instruct the homeowner how to operate the
burner.
Installer must instruct the homeowner how to do basic maintenance.
7.
8.
CARTON CONTENTS & HARDWARE PACK
CARTON CONTENTS
HARDWARE PACK CONTENTS
1
3
1
2
(VFSR SHOWN)
2
3
Items not shown to scale.
Index
Number
5
4
Description
Quantity
Supplied
1
1/4" x 1-1/4" Slotted Hex Head
Anchor Screw
3
2
#10 x 1/2" Phillips Hex Head Screw
3
3
Clamp
1
See Parts Lists on page 25 for ordering replacement parts. Do
not order batteries, bolts, screws, washers or nuts. They are
standard hardware items and can be purchased at any local
hardware store.
6
Items not shown to scale.
Index
Number
1
Description
Quantity
Supplied
Burner Assembly
1
2 bags
2
Decorative Rocks
3
Valve Shield (VFSM models)
4
Rock Wool
5
Hardware Package
1
6
Log Switch
1
1
1 bag
See Parts Lists on page 25 for ordering replacement parts. Do
not order batteries, bolts, screws, washers or nuts. They are
standard hardware items and can be purchased at any local
hardware store.
Page 2
27829-13-1019
TABLE OF CONTENTS
SECTION
PAGE
Before You Start............................................................................................................................ 2
Carton Contents & Hardware Pack............................................................................................... 2
Important Soot Prevention Steps.................................................................................................. 4
Product Specifications................................................................................................................... 5
Introduction.................................................................................................................................... 6
Accessories................................................................................................................................... 6
Important Safety Information...................................................................................................... 7-8
Safety Information For Users Of Propane Gas............................................................................. 9
Requirements For Canada.......................................................................................................... 10
General Information......................................................................................................................11
Water Vapor: A By-Product Of Unvented Room Heaters.............................................................11
Provisions For Adequate Combustion & Ventilation Air............................................................... 12
Clearances............................................................................................................................. 13-14
Combustible Material................................................................................................................... 15
Fireplace Preparation.................................................................................................................. 15
Installing As A Vented Appliance................................................................................................. 16
Before Fully Installing The Appliance.......................................................................................... 16
Gas Supply.................................................................................................................................. 17
Placement Of Glowing Embers And Lava Rock.......................................................................... 18
Operation Instructions/Flame Appearance.................................................................................. 18
Lighting Instructions - Vfsr-(16,18,24,30)................................................................................. 19
Lighting Instructions - Vfsm-(18,24,30) ..................................................................................... 20
Pilot Flame Characteristics.......................................................................................................... 21
Cleaning And Servicing............................................................................................................... 22
Wiring.......................................................................................................................................... 23
Troubleshooting........................................................................................................................... 24
Master Parts Distributor List........................................................................................................ 25
How To Order Repair Parts......................................................................................................... 25
Parts List..................................................................................................................................... 26
Parts View................................................................................................................................... 27
Warranty...................................................................................................................................... 28
27829-13-1019
Page 3
IMPORTANT SOOT PREVENTION STEPS
NOTICE
IMPORTANT
NOTICE
INSTALLER - SERVICE PERSON - HOMEOWNER
SOOT MAY BE CREATED IF THE FOLLOWING DIRECTIONS ARE NOT FOLLOWED.
1. Ensure the air shutter is set to the specification. See
Figures 1, 2, and 3 on this page and Tables 1 and 2
on the Product Specifications page 5.
2. Ensure burner, venturi, and air shutter are free of dirt,
lint, animal hair (i.e. cat and dog) or anything that may
block the needed air flow. See Cleaning and Servicing,
page 22.
3.
Verify the air shutter for the correct setting. Refer to Tables 1
and 2 on page 5 for specific air shutter settings for each model.
Natural Gas Models - The air shutter setting must be
1/16" or 1/8". See Figures 1 and 2 and Table 1 on page 5.
WARNING: Do not allow fans to blow directly into
the fireplace. Avoid any drafts that alter burner flame
patterns. Pay particular attention to ceiling fans and
exhaust fans.
4. Do not place debris, additional logs or other articles on
the log set during operation.
5. Avoid the use of scented air fresheners while the log
set is in operation. A residue can be produced which
may produce soot.
6. Avoid the use of decorative or scented candles while
the log set is in operation. Soot may be produced from
the by-products of a burning candle. Some candles
also produce soot.
Figure 1
(1/16” opening shown)
NOTICE: Orifice shield removed for photo clarity.
Test 1/16 or 1/8 air shutter setting with a round object like a
drill bit. The object should barely slide between the opening.
See Figure 2.
7. Do not place lava rocks on burner or burner ports. The
lava rocks should only be placed on the fireplace floor.
8. Do not place rock wool (embers) over the large ports
of the burner.
9. Check level of ceramic media in burner if the burner
has ceramic media. Burner should be full, up to the
level of openings in the burner top.
10. Annual inspection and cleaning by your dealer or a
qualified service technician is recommended to prevent malfunction and/or sooting.
11. Install logs according to the installation instructions.
Do not alter log placement from the prescribed layout
in this manual. Only use Empire Logs specially made
for this burner.
Figure 2
(1/16" opening shown)
Propane Gas Models- The air shutter setting must be "fully
open." See Figure 3 and Table 2 on page 5.
The air shutter setting must be set to the maximum opening.
12. Verify the venturi tube is not bent or distorted. The
main burner orifice must be centered in the venturi
tube for proper combustion and to prevent sooting.
Figure 3
NOTICE: Orifice shield removed for photo clarity.
Page 4
27829-13-1019
PRODUCT SPECIFICATIONS
Natural Gas
Millivolt
Manual
Millivolt
Manual
3.5" W.C.
6.0" W.C.
10.0" W.C.
10.0" W.C.
Max.
10.5" W.C.
10.5" W.C.
13.0" W.C.
13.0" W.C.
Min.
5.0" W.C.
7.0" W.C.
11.0" W.C.
11.0" W.C.
Valve Type
Orifice
BTUH
Max. Rate
BTUH
Med. Rate
BTUH
Min. Rate
Regulator pressure setting
Gas inlet pressure
Model
Gas
Propane Gas
VFSR-16
Natural
Millivolt
#41
25,000
—
17,500
VFSR-16
Propane
Millivolt
#54
22,500
—
15,750
VFSR-18
Natural
Millivolt
#36
32,000
—
22,000
VFSR-18
Propane
Millivolt
1.65mm
32,000
—
22,000
VFSM-18
Natural
Manual
#38
32,000
27,000
22,000
VFSM-18
Propane
Manual
1.65mm
32,000
27,000
22,000
VFSR-24
Natural
Millivolt
#33
36,000
—
25,000
VFSR-24
Propane
Millivolt
#50
36,000
—
25,000
VFSM-24
Natural
Manual
#33
36,000
27,000
22,000
VFSM-24
Propane
Manual
#50
36,000
27,000
22,000
VFSR-30
Natural
Millivolt
#32
38,000
—
26,000
VFSR-30
Propane
Millivolt
#49
38,000
—
26,000
VFSM-30
Natural
Manual
#31
38,000
27,000
22,000
VFSM-30
Propane
Manual
#49
38,000
27,000
22,000
Table 1 - Air Shutter Opening
Natural Gas Models
Table 2 - Air Shutter Opening
Propane Gas Models
Model
Air Shutter Opening
Model
Air Shutter Opening
VFSR-16
1/16"
VFSR-16
Full Open
VFSR-18
1/8"
VFSR-18
Full Open
VFSM-18
1/8"
VFSM-18
Full Open
VFSR-24
1/16"
VFSR-24
Full Open
VFSM-24
1/16"
VFSM-24
Full Open
VFSR-30
1/16"
VFSR-30
Full Open
VFSM-30
1/16"
VFSM-30
Full Open
27829-13-1019
Page 5
INTRODUCTION
IMPORTANT: Read all instructions carefully before starting
installation. Failure to follow these installation instructions may
result in a possible fire hazard and will void the warranty.
Save this manual for future reference.
Please read this manual before installing and using the
appliance.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card supplied
with unvented room heater/vented decorative appliance.
3. Installer should show owner how to start and operate unvented
room heater/vented decorative appliance.
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of an unvented
room heater/vented decorative appliance.
This appliance may be installed in an aftermarket* manufactured
(mobile) home, where not prohibited by state or local codes.
*Aftermarket: Completion of sale, not for purpose of resale, from
the manufacturer.
Well Head Gas Installations
Some Natural Gas utilities use “well head” gas. This may affect
the Btu output of the unit and promote sooting. Units shall not be
converted to use well head gas.
This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other gases.
New Installation
Solid-fuels shall not be burned in a fireplace where a vented decorative
appliance is installed.
A vented decorative appliance must be installed only in a
solid-fuel burning fireplace with a working flue and constructed of
non-combustible material.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
Attention: During initial use of log set you will detect an odor
as the logs cure.
Notice: During initial firing of this unit, its paint will bake out, and
smoke will occur. To prevent triggering of smoke alarms, ventilate
the room in which the unit is installed.
WARNING
This appliance is for installation only in a solid-fuel burning
masonry or UL 127 factory-built fireplace or in a listed
ventless firebox enclosure. It has been design certified for
these installations. Exception: DO NOT install this appliance
in a factory-built fireplace that includes instructions stating
it has not been tested or should not be used with unvented
gas logs.
WARNING
Any modification to this unvented gas heater or its controls
can be dangerous. Improper installation or use of the heater
can cause serious injury or death from fire, burns, explosion
or carbon monoxide poisoning.
ACCESSORIES
The following accessory parts can be obtained from your Empire Comfort Systems dealer. Contact your Empire Dealer for more accessory options. If you need additional information beyond what your dealer can furnish, contact Empire Comfort Systems Inc., 918 Freeburg
Ave., Belleville, Illinois 62220-2623.
Model Number
EK-1
ELH-1
DCG24BL
Page 6
Description
Embers Kit
Fireplace Hood for Vent-Free Logs - Black
Black Decorative Grate
LR18
2-in. Riser (fits 18-in burner)
LR24
2-in. Riser (fits 24-in burner)
LR30
2-in Riser (fits 30-in burner)
PE20
Platinum Embers
GF24
Flex Gas Line, 24-in. - Stainless Steel
For use with VFSR models only
Model Number
FRBC
FRBTC
Description
Battery Operated Remote Control
Battery Operated Remote Control with
Thermostat
FREC
Electric Remote Control
FWS1
Wall Switch
TMV
Wall Thermostat, Millivolt - Reed Switch
Notice: Thermostats are for Vent-Free Applications only.
Notice: FREC requires receptical for 120V plug
27829-13-1019
IMPORTANT SAFETY INFORMATION
Definitions:
DANGER - Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING - Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION - Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE - Addresses practices not related to personal injury.
WARNING
When used without adequate combustion and ventilation air,
heater may give off CARBON MONOXIDE, an odorless, poisonous gas.
Do not install heater until all necessary provisions are
made for combustion and ventilation air. Consult the written instructions provided with the heater for information
concerning combustion and ventilation air. In the absence
of instructions, refer to the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Air for Combustion and Ventilation, or
applicable local codes.
This heater is equipped with a pilot light safety system designed to turn off the heater if not enough fresh air
is available.
Do NOT TAMPER WITH PILOT LIGHT SAFETY SYSTEM!
If heater shuts off, do not relight until you provide fresh air.
If heater keeps shutting off, have it serviced. Keep burner and
control compartment clean.
Carbon monoxide poisoning may lead to death.
Early signs of carbon monoxide poisoning resemble the flu,
with headache, dizziness and/or nausea. If you have these
signs, heater may not be working properly. Get fresh air at
once! Have heater serviced.
Some people — pregnant women, persons with heart or lung
disease, anemia, those under the influence of alcohol , those
at high altitudes — are more affected by carbon monoxide
than others.
The pilot light safety system senses the depletion of oxygen
at its location. If this heater is installed in a structure having a
high vertical dimension, the possibility exists that the oxygen
supply at the higher levels will be less than that at the heater.
In this type of application, a fan to circulate the structure air will
minimize this effect. The use of this fan will also improve the
comfort level in the structure. When a fan is used to circulate
air, it should be located so that the air flow is not directed at
the burner.
27829-13-1019
DANGER
The installer of this product is responsible for the verifying the
correct position of the air shutter and adjusting it if required.
If not adjusted to the proper opening, a fire, explosion, or
production of carbon monoxide may result causing property
damage, personal injury or loss of life.
DANGER
The installer of this product is responsible for testing all
connections for gas leaks. A gas leak will create a situation
where a fire, explosion, or production of carbon monoxide may
result causing property damage, personal injury or loss of life.
WARNING
Do not use a blower insert, heat exchanger insert or other
accessory not approved for use with this heater.
WARNING
This burner needs fresh air for ventilation to run properly.
This burner has an ODS (oxygen depletion sensor) which will
shut down the fireplace if adequate fresh air is not available.
See troubleshooting section in the instructions.
WARNING
Do not allow fans to blow directly into the fireplace. Avoid
any drafts that alter burner flame patterns.
WARNING
DO NOT operate this appliance unless all components
including logs, burners, and controls are in good working
condition. Never operate this appliance if any log or twig is
broken, or out of their intended position. Refer to the Log set
placement instructions for correct log and twig positioning.
Replacement components are available through your local
dealer as indicated in the How to Order Repair Parts section
of the appliance manual.
WARNING
Failure to keep the primary air opening(s) of the burner(s)
clean may result in sooting and property damage.
WARNING
All previously applied loose material must be removed prior
to reapplication.
Page 7
IMPORTANT SAFETY INFORMATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Avoid the use of scented air fresheners (plug in type air
fresheners, etc. ) while the log set is in operation. Air fresheners
produce a residue in the air similar to candles and may produce
a soot like substance.
Avoid the use of scented or decorative candles while the log
set is in operation. Candles produce a residue in the air that
creates a soot like substance. Burning candles while the log
set is operating magnifies the problem. It should be noted that
candles, in general, produce soot. The amount of time burned
and the quantity of candles burned will determine the amount
of soot produced and deposited.
Installation and repair should be done by a qualified service person. This appliance should be inspected before use
and at least annually by a professional service person. More
frequent cleaning may be required due to excessive lint from
carpeting, bedding materials, etc. It is imperative that control
compartments, burners and circulating air passageways of the
appliance be kept clean.
Do not place debris, additional logs or other articles on the log
set during operation.
An unvented room heater having an input rating of more than
6,000 Btu per hour shall not be installed in a bathroom
An unvented room heater having an input rating of more than 10,000
Btu per hour shall not be installed in a bedroom or bathroom.
Due to high temperatures, the appliance should be located out of
traffic and away from furniture and draperies.
Children and adults should be alerted to the hazard of high surface
temperature and should stay away to avoid burns or clothing
ignition.
Young children should be carefully supervised when they are in
the same room with the appliance.
Do not place clothing or other flammable material on or near the
appliance.
Do not use this room heater if any part has been under water.
Immediately call a qualified service technician to inspect the
room heater and to replace any part of the control system and
any gas control which has been under water.
You must operate heater with fireplace screen in place.
During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain oils, films
or bonding agents. These bonding agents are not harmful but
may produce annoying smoke and smells as they are burned
off during initial operation of the appliance. This is a normal
temporary occurrence. A window should be opened during the
initial bake out period.
Correct installation of the ceramic fiber logs, proper location
of the heater and annual cleaning are necessary to avoid
potential problems with sooting. Sooting, resulting from improper
installation or operation, can settle on surfaces outside the
fireplace. See instructions for proper installation.
Keep appliance area clear and free from combustible materials,
gasoline and other flammable vapors and liquids.
Sooting: A vent-free fireplace or burner draws room air to
support combustion. Lightweight particles suspended in the
air – including dust, carpet fibers, candle or tobacco smoke,
and pet hair – will be drawn toward the fireplace. These can
lead to soot build up on logs, fireplace walls, and even walls
of the room. To prevent malfunctions and sooting, have your
dealer perform an inspection and cleaning each year – before the heating season. If you have pets or excessive dust,
more frequent cleaning may be necessary. See cleaning and
service section in this manual.
Page 8
•
•
•
•
•
•
•
•
•
Use Non-Combustible Materials where indicated for the fireplace installation. Non-combustible material do not ignite or
burn as a result of using the fireplace. These include metal,
brick, ceramic, concrete, slate, glass, and plaster. Adhesives
must be rated for high temperatures. Any mechanical fasteners used to install material must also be non-combustible,
including wall anchors and tile spacers. Materials that pass
the ASTM E 136 test (Standard Test Method for Behavior of
Materials in a Vertical Tube Furnace at 750C) are considered
non-combustible.
Do not allow Combustible Materials adjacent to or in contact
with the fireplace or venting. Combustible materials include
wood, compressed paper, plant fibers, or other materials that
will burn. These materials are considered combustible even
when treated with fire-retardant chemicals.
Proper installation, burner pan location and log placement is
important to achieve optimum look and performance of your
gas log set. The logs have been designed for easy location
and placement on the grate and must be followed for proper
operation.
A yearly examination and cleaning of the venting system of
the solid-fuel burning fireplace must be performed by a qualified agency.
Do not place embers (rock wool) over large ports in rear portion of burner.
Do not place lava rocks on burner, logs or rock wool (glowing
embers). The lava rocks should only be placed on the fireplace floor.
Replacement of loose material (glowing embers) must be purchased from a dealer of Empire Comfort Systems Inc. Application of loose material (glowing embers may adversely affect
performance of the heater.
Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into fireplace. Do not place a blower
inside the burner area of the firebox. Ceiling fans may create
drafts that alter flame patterns. Sooting and improper burning
will result.
Installing a television above a fireplace has become a desirable feature; however, the following information should be
considered.
All fireplaces, whether decorative or heater rated create
heat. Most television manufacturers recommend not placing
a television near a heat source. Because there is a large
variety of television manufactures, styles and sizes, it is impractical to test every potential installation. If you choose to
install a television above or near your fireplace, understand
that Empire Comfort Systems accepts no responsibility for
this decision and any injury or damage due to this application
is the sole responsibility of the owner. Additionally, it is highly
recommended to turn off the fireplace and let it cool down
before servicing or using the operational buttons located
on the television. In all cases, the television manufacturer’s
instructions and warnings should be followed.
27829-13-1019
SAFETY INFORMATION FOR USERS OF Propane GAS
Propane is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and colorless.
You may not know all the following safety precautions which
can protect both you and your family from an accident. Read
them carefully now, then review them point by point with the
members of your household. Someday when there may not
be a minute to lose, everyone's safety will depend on knowing
exactly what to do. If, after reading the following information,
you feel you still need more information, please contact your
gas supplier.
Propane Gas WARNING ODOR
If a gas leak happens, you should be able to smell the gas
because of the odorant put in the Propane Gas.
That's your signal to go into immediate action!
•
•
•
•
•
•
Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
Close all gas tank or cylinder supply valves.
Propane Gas is heavier than air and may settle in low areas
such as basements. When you have reason to suspect a gas
leak, keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
Use your neighbor's phone and call a trained Propane Gas
service person and the fire department. Even though you may
not continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained Propane Gas service people should repair the leak,
then check and relight the gas appliance for you.
no odor detected - odor fade
Some people cannot smell well. Some people cannot smell
the odor of the chemical put into the gas. You must find out if
you can smell the odorant in propane. Smoking can decrease
your ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors in
the area mask the gas odor. People may not smell the gas odor or
their minds are on something else. Thinking about smelling a gas
odor can make it easier to smell.
The odorant in Propane Gas is colorless, and it can fade under
some circumstances. For example, if there is an underground
leak, the movement of the gas through soil can filter the odorant.
Odorants in Propane Gas also are subject to oxidation. This fading
can occur if there is rust inside the storage tank or in iron gas pipes.
some points to remember
•
Learn to recognize the odor of Propane Gas. Your local
Propane Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use it to find out what the propane odor smells like. If
you suspect that your Propane Gas has a weak or abnormal
odor, call your Propane Gas Dealer.
•
If you are not qualified, do not light pilot lights, perform service,
or make adjustments to appliances on the Propane Gas system.
If you are qualified, consciously think about the odor of Propane
Gas prior to and while lighting pilot lights or performing service
or making adjustments.
•
Sometimes a basement or a closed-up house has a musty
smell that can cover up the Propane Gas odor. Do not try to
light pilot lights, perform service, or make adjustments in an
area where the conditions are such that you may not detect
the odor if there has been a leak of Propane Gas.
•
Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people should
be particularly alert and careful when new tanks or cylinders
are placed in service. Odor fade can occur in new tanks, or
reinstalled old tanks, if they are filled and allowed to set too
long before refilling. Cylinders and tanks which have been out
of service for a time may develop internal rust which will cause
odor fade. If such conditions are suspected to exist, a periodic
sniff test of the gas is advisable. If you have any question
about the gas odor, call your Propane Gas Dealer. A periodic sniff test of the Propane Gas is a good safety measure
under any condition.
•
If, at any time, you do not smell the Propane Gas odorant and
you think you should, assume you have a leak. Then take the
same immediate action recommended above for the occasion
when you do detect the odorized Propane Gas.
•
If you experience a complete "gas out," (the container is under
no vapor pressure), turn the tank valve off immediately. If the
container valve is left on, the container may draw in some air
through openings such as pilot light orifices. If this occurs, some
new internal rusting could occur. If the valve is left open, then
treat the container as a new tank. Always be sure your container is under vapor pressure by turning it off at the container
before it goes completely empty or having it refilled before it is
completely empty.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That will
take some of the odorant out of the gas, reducing its odor intensity.
Propane Gas may stratify in a closed area, and the odor intensity
could vary at different levels. Since it is heavier than air, there may
be more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
27829-13-1019
Page 9
REQUIREMENTS FOR CANADA
This unit cannot be installed in a UNVENTED application,
this unit can only be installed as a VENTED application
with these requirements.
IMPORTANT SAFETY INFORMATION
This unit complies with ANSI Z21.60 / Z21.11 and CGA 2.26
Decorative Gas Appliances For Installation In Solid Fuel
Burning Fireplaces. Do not burn wood or solid fuels in a
fireplace where a decorative gas log set is installed. This
appliance is for installation only in a solid fuel burning fireplace, masonry fireplace or manufactured fireplace.
WARNING
Do not operate this gas log set with glass doors closed
•
•
•
WARNING
Any modification to this gas log set or to controls can
be dangerous. Improper installation or use of the gas
log set can cause serious injury or death from fire,
burns, explosion or carbon monoxide poisoning.
1. Please follow all local codes regarding installation,
combustion and ventilation air or in the absence of
local codes follow the National Fuel Gas Code ANSI
Z223.1(U.S. installation), or CAN/CGA-B149, Installation Code (Canada installation).
2. Proper installation, burner pan location and log
placement is important to achieve optimum look and
performance of your gas log set. The logs have been
designed for easy location and placement on the grate
and must be followed for proper operation.
3. Do not operate this log set with glass doors in the closed
position. A fireplace screen must be in place when the
log set is burning. Adequate combustion air must be
provided for proper venting. All flames should go up
and out the top of the firebox into the flue vent. If any
flames float or curl forward into the room do not operate
appliance. Check for an open flue and adequate
combustion air into the room. A damper clamp must
be installed on the firebox damper to maintain an open
flue vent condition. Refer to page 16 INSTALLING
DAMPER CLAMP
4. Young children must be carefully supervised when
they are in the same room as the gas log while in
operation. Do not place stockings, clothing or any
flammable material above or near the fireplace.
5. Do not substitute or use materials other than those
supplied for use with the log set.
6. Also refer to IMPORTANT SAFETY INFORMATION on
pages 7 and 9 of this manual.
Page 10
•
Clothing or other flammable material should not be
placed on or near the appliance.
Do not place trash or other articles on the log set during
operation.
During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain oils,
films or bonding agents. These bonding agents are not
harmful but may produce annoying smoke and smells as
they are burned off during initial operation of the appliance. This is a normal temporary occurrence. A window
should be opened during the initial bake out period.
Keep burner and control compartment clean.
WARNING
Before installing in a solid fuel burning fireplace,
the chimney flue and firebox must be cleaned of
soot, creosote, ashes and loose paint by a qualified
chimney cleaner.
•
•
•
•
•
•
•
•
Installation and repair should be done by a qualified service person. The appliance should be inspected before
use and at least annually by a qualified service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.
Do not put anything around the fireplace that will
obstruct the flow of ventilation air.
Do keep the appliance area clear and free from
combustible material, gasoline and other flammable vapors and liquids.
A yearly examination and cleaning of the venting system
of the solid-fuel burning fireplace must be performed by
a qualified agency.
Do make a periodic visual check of pilot and burners.
Clean and replace damaged parts.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
Never burn solid fuels in fireplace where a gas log set is
installed.
This unit complies with ANSI Z21.60 / Z21.11 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this
appliance in a vented configuration. Check your state or
local codes.
27829-13-1019
GENERAL INFORMATION
This is an unvented gas-fired heater. It uses air (oxygen) from the
room in which it is installed. Provisions for adequate combustion
and ventilation air must be provided.
Keep room area clear and free from combustible materials, gasoline
and other flammable vapors and liquids.
Unvented gas heaters are a supplemental zone heater. They are not
intended to be a primary heating appliance. Water vapor produced
by an unvented heater can create moisture problems in a home
when operated for extended periods of time.
During manufacturing, fabricating and shipping, various components
of this appliance are treated with certain oils, films or bonding agents.
These chemicals are not harmful but may produce annoying smoke
and smells as they are burned off during the initial operation of the
appliance; possibly causing headaches or eye or lung irritation. This
is a normal and temporary occurrence.
The initial break-in operation should last 2-3 hours with the burner
at the highest setting. Provide maximum ventilation by opening
windows or doors to allow odors to dissipate. Any odors remaining
after this initial break-in period will be slight and will disappear with
continued use.
This appliance must not be used with glass doors in the closed
position. This can lead to pilot outages and severe sooting outside
the fireplace. This appliance must be operated with the glass doors
fully opened.
Do not use this room heater if any part has been under water.
Immediately call a qualified service technician to inspect the room
heater and replace any part of the control system and any gas
control which has been under water.
WARNING
Handle the gas log burner assembly by the grate and legs only.
Do not pick the unit up by the burner.
Gloves are recommended when handling logs to prevent skin
irritation. Logs are fragile - Handle with care.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be
performed only by a qualified agency. The term "qualified agency"
means any individual, firm, corporation, or company that either in
person or through a representative is engaged in and is responsible for (a) the installation, testing, or replacement of gas piping
or (b) the connection, installation, testing, repair, or servicing of
equipment; that is experienced in such work; that is familiar with all
precautions required, and that has complied with all the
requirements of the authority having jurisdiction.
Commonwealth of Massachusetts: The installation must be
made by a licensed plumber or gas fitter in the Commonwealth
of Massachusetts.
Sellers of Unvented Propane or Natural Gas-Fired supplemental
room heaters shall provide to each purchaser a copy of 527 CMR30 upon sale of the unit.
The installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI Z223.1.*
*Available from the American National Standards Institute, Inc. 11
West 42nd St., New York, N.Y. 10018.
High Altitudes: For altitudes/elevation above 2,000 feet ratings
should be reduced at the rate of 4 percent for each 1,000 feet above
sea level. Contact the manufacturer.
This appliance is equipped for (Natural or Propane) Gas.
Field conversion is not permitted.
Before you get started
Carefully inspect the contents for shipping damage. If any parts are
missing or damaged, immediately inform the dealer from whom you
purchased the appliance. Do not attempt to install any part of the
appliance unless you have all parts in good condition.
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An unvented room
heater produces approximately one (1) ounce (30ml) of water for
every 1,000 BTU's (.3KW's) of gas input per hour.
Unvented room heaters must be used as supplemental heat (a
room) rather than a primary heat source (an entire house). In most
supplemental heat applications, the water vapor does not create a
problem. In most applications, the water vapor enhances the low
humidity atmosphere experienced during cold weather.
27829-13-1019
The following steps will help insure that water vapor does not
become a problem.
1. Be sure the heater is sized properly for the application, including
ample combustion air and circulation air.
2. If high humidity is experienced, a dehumidifier may be used to
help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source
(an entire house).
Page 11
PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR
This heater shall not be installed in a confined space unless provisions
are provided for adequate combustion and ventilation air.
DIVIDER
The National Fuel Gas Code defines a confined space as a space
whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8m3
per kw) of the aggregate input rating of all appliances installed in that
space and an unconfined space as a space whose volume is not less
than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms
communicating directly with the space in which the appliances are
installed, through openings not furnished with doors, are considered a
part of the unconfined space.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh
air for combustion and ventilation. However, in buildings of unusually
tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction
where:
a. Walls and ceilings exposed to the outside atmosphere have a
continuous water vapor retarder with a rating of one perm or
less with openings gasketed or sealed, and
b. Weatherstripping has been added on openable windows and
doors, and
c. Caulking or sealants are applied to areas such as joints around
window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for
plumbing, electrical, and gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide
additional fresh air.
WARNING
If the area in which the heater may be operated is smaller than
that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and
ventilation air by one of the methods described in the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and
Ventilation, or applicable local codes.
Page 12
FIREPLACE
H
L2
L1
W
Example of Large Room with 1/2 Wall divider.
Figure 4
The following formula can be used to determine the maximum heater
rating per the definition of unconfined space:
Btu/Hr =
(L1 + L2)FT x (W)FT x (H)FT
x 1000
50
If the area in which the heater may be operated is smaller than that defined
as an unconfined space, provide adequate combustion and ventilation
air by one of the methods described in the National Fuel Gas Code,
ANSI Z223.1, NFPA54.
Adhere to all codes, or in their absence, the latest edition of THE
NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA54 which can be
obtained from:
American National Standards InstituteNational Fire Protection Association, Inc.
11 West 42nd St.
Batterymarch Park
New York, NY 10018
Quincy, MA 02269
27829-13-1019
CLEARANCES
Follow these instructions to ensure safe installation.
Failure to follow instructions exactly can create a fire hazard.
Minimum Dimensions For Solid Fuel Burning Fireplaces UL127
Factory Built Fireplaces
Sidewall & Ceiling Clearances
18”, 24”, 30” Burner 41”
16” Burner 36”
W
6”
T
Figure 7
U
V
Model
W
V
U
T
VFSR-16
18"
11 1/2"
24"
18"
VFSR-18
17"
14"
28"
17"
VFSM-18
21"
14"
32"
17"
VFSR-24
23"
14"
30"
18"
VFSM-24
27"
14"
34"
18"
VFSR-30
26"
14"
34"
20"
VFSM-30
30"
14"
38"
20"
The sides of the fireplace opening must be 6" from any combustible
wall. The ceiling must be at least 36" (for the 16" burner) and 41"
(for 18", 24" and 30" burner) from the fireplace opening.
Mantel Clearances Without Hood
You must have non-combustible materials above the fireplace
opening. Non-combustible material must extend at least 12" above
fireplace opening. With sheet metal, you must have non-combustible
material behind it.
Non-combustible materials such as slate and marble must be
at least 1/2" thick. Sheet metal should not be installed onto
combustible material.
10” and less Mantel
NON-COMBUSTIBLE
MATERIAL
Figure 5
The dimensions shown and defined in the fireplace manufacturer’s
instructions are minimum clearances to maintain in installing this
heater. Left and right clearances are determined when facing the
front of the heater.
12”
HEATER IN FIREPLACE
OR FIREBOX
Glass Doors
Make sure that glass doors are fully open during all operations
of the logset. The opening of the glass door frame should be the
dimension used for the minimum front opening of the firebox.
INCORRECT DOOR POSITION WHEN
OPERATING THE FIREPLACE
Figure 8
If your installation does not meet the above clearances, you can
proceed to one of the following steps to see if these clearances
are possible:
•
Use a hood (see mantel clearances with hood)
•
Operate the heater with flue damper open. See page 16 for
Installing as a Vented Appliance.
•
Raise the mantel to the proper height.
•
Remove the mantel.
Non-Combustible
Material Distance
PARTIALLY OPEN DOORS.
Figure 6
27829-13-1019
28”
Requirements for Safe Installation
12" or more
Non-combustible material
Less than 12"
Non-combustible material must be extended to at least 8" with the installation
of the optional fireplace hood. If you cannot extend non-combustible material at
least 8", you must operate heater with
flue damper open.
Page 13
CLEARANCES (CONT'D)
Mantel Clearances with Hood
You must have non-combustible materials above the fireplace
opening. Non-combustible material must extend at least 8" above
fireplace opening. With sheet metal, you must have non-combustible
material behind it.
Non-combustible materials such as slate and marble must be
at least 1/2" thick. Sheet metal should not be installed onto
combustible material.
Example: A mantel may project from the wall a maximum of 2" at a
minimum of 8" above the opening, and a maximum of 6" at a
minimum of 15" above the opening.
8” Mantel
6” Mantel
2” Mantel
16.0”
14.25”
8”
COMBUSTIBLE
MATERIAL
Note: If floor is sunken below the opening, the unit needs to be
raised above the hearth level or the opening of the glass door
surround.
15.0”
HOOD
BURNER IN
FIREPLACE OR
FIREBOX
Figure 9
If your installation does not meet the above minimum clearances,
you must proceed to one of the following steps:
•
Operate the heater with the flue damper open. See page 16
for Installing as a Vented Appliance.
•
Raise the mantel to the proper height.
•
Remove the mantel.
Page 14
BURNER IN
FIREPLACE OR
FIREBOX
Figure 10
4” Mantel
NON-COMBUSTIBLE
MATERIAL
8” WITH HOOD
Floor Clearance
If installing heater at floor level, the minimum distance to combustibles is “0” inches.
BURNER IN
FIREPLACE
OR FIREBOX
Hearth
Figure 10a - Example of incorrect installation
27829-13-1019
COMBUSTIBLE MATERIAL
Do not attach combustible material to the mantel of your fireplace.
This is a fire hazard.
Figure 11
Use non-combustible materials where indicated for the fireplace
installation. Non-combustible materials do not ignite or burn as a
result of using the fireplace. These include metal, brick, ceramic,
concrete, slate, glass, and plaster. Adhesives must be rated for
fireplace high temperature applications. Any mechanical fasteners used to install materials must also be non-combustible,
including wall anchors and tile spacers. Materials that pass the
ASTM E-136 test (Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C) are considered noncombustible.
Do not allow combustible materials adjacent to or in contact with
the fireplace or venting. Combustible materials include wood,
compressed paper, plant fibers, or other materials that will burn.
These materials are considered combustible even when treated
with fire-retardant chemicals.
Television Considerations
Installing a television above a fireplace has become a desirable
feature; however, the following information should be considered.
All fireplaces, whether decorative or heater rated create heat.
Most television manufacturers recommend not placing a television near a heat source. Because there is a large variety of
television manufactures, styles and sizes, it is impractical to test
every potential installation. If you choose to install a television
above or near your fireplace, understand that Empire Comfort
Systems accepts no responsibility for this decision and any injury
or damage due to this application is the sole responsibility of
the owner. Additionally, it is highly recommended to turn off the
fireplace and let it cool down before servicing or using the operational buttons located on the television. In all cases, the television
manufacturer’s instructions and warnings should be followed.
FIREPLACE PREPARATION
•
•
Turn off gas supply to fireplace or firebox.
Have the fireplace floor and chimney professionally cleaned to
remove ashes, soot, creosote or other obstructions. Have this
cleaning performed annually after installation.
•
Seal any fresh air vents or ash clean-out doors located on floor
or wall of fireplace. If not, drafting may cause pilot outage or
sooting. Use a heat-resistant sealant. Do not seal chimney flue
damper.
Install and operate the appliance as directed in this manual.
FOR MASONRY BUILT FIREPLACES
free opening area of chimnEy damper for venting
combustion products from decorative appliances
for installation in solid fuel burning fireplaces
FOR FACTORY BUILT FIREPLACES
Free opening area of chimney damper for venting
combustion products from decorative appliances
for installation in solid fuel burning fireplaces
*
**
Appliance Input Rate (BTU/hr)
Chimney
Height* (ft)
20
10
11.3
16.6
22.1
15
8.6
12.6
17.3
20
7.5
10.8
14.5
30
40
Minimum Opening** (sq. in.)
25
6.6
9.6
12.6
30
6.2
9.1
11.3
35
5.7
8.0
10.8
40
5.3
7.5
10.2
*
**
Appliance Input Rate (BTU/hr)
Chimney
Height* (ft)
20
6
17.6
25.7
33.8
8
16.5
23.7
31.2
10
15.1
21.7
28.7
15
14.1
19.9
26.1
20
12.9
18.5
23.7
30
12.2
16.9
21.6
30
40
Minimum Opening** (sq. in.)
Height is from hearth to top of chimney and the minimum height
is 6 feet.
Chart shows minimum opening (sq. in.) for given height and
input rate.
Height is from hearth to top of chimney and the minimum height
is 10 feet.
Chart shows minimum opening (sq. in.) for given height and
input rate.
27829-13-1019
Page 15
INSTALLING AS A VENTED APPLIANCE
Notice: (Damper Clamp Installation)
When installing your log set as a vented installation the damper
clamp (provided in the hardware kit) must be used.
When installing your log set as a vent-free installation the damper
clamp can be used to eliminate the potential for odors when burning
the logs for the first time.
Installing Damper Clamp
Remove all ashes or other debris from the fireplace. If the fireplace
is equipped with an ash dump be sure to seal the door with furnace
cement or high temperature silicone. Be sure to check the damper
for proper operation and verify that the flue passageway is open.
Place the clamp over the lip of the damper and tighten the hold
down bolt until the clamp is securely attached to the damper. This
will prevent the damper from accidentally closing.
Manual and millivolt controlled gas logs may be installed as a
vented decorative log set in compliance with ANSI Z21.60 / Z21.11
and National Fuel Gas Code. When the gas logs are operated with
the damper open, non-combustible material and minimum mantel
requirements do not apply.
Figure 12
BEFORE FULLY INSTALLING THE APPLIANCE
•
•
Turn off the gas supply to the fireplace or firebox.
Seal any fresh air vents and/or ash clean-out doors located on
the floor or wall of the fireplace. If left unsealed, drafting may
cause pilot outage or sooting. Use a heat resistant sealant. Do
not seal the chimney flue damper.
Before installing in a solid fuel burning fireplace, the chimney flue
and firebox must be cleaned of soot, creosote, ashes and loose
paint by a qualified chimney cleaner.
You must secure the gas log heater to the fireplace floor. If
not, the entire unit may move when you adjust the controls.
Movement of unit may cause shifting of the gas logs which
leads to sooting and improper burning. Grate movement
could cause a gas leak.
Assembly Procedure:
1. Center the gas log unit in the fireplace or firebox. Make
certain the front feet of the grate sit inside the front edge of the
fireplace or firebox.
2. An anchor hole is provided in the two bottom side members of
the grate frame. After centering the grate correctly, mark the
hole positions on the fireplace/firebox floor. Drill two (2) 5/32"
diameter holes approximately 1-1/2" deep for masonry screws
or 1/8" hole for sheet metal screws.
3. Anchor the grate to the fireplace/firebox floor using the screws
provided. Refer to Figure 13.
Proper installation of the grate is essential to prevent any
movement of the gas logs and controls during operation.
Special care is required if you are installing the unit into a
sunken fireplace. You must raise the fireplace floor to allow
access to gas log controls. This will insure adequate air
flow and guard against sooting. Raise the fireplace floor
using noncombustible materials.
Figure 13 - VFSR Shown
Page 16
27829-13-1019
GAS SUPPLY
Check all local codes for requirements, especially for the size and
type of gas supply line required.
Recommended Gas Pipe Diameter
Pipe
Length
Schedule 40 Pipe
Inside Diameter
Tubing, Type L
Outside Diameter
Natural
Propane
Natural
Propane
0-10 feet
0-3 meters
1/2”
12.7mm
3/8”
9.5mm
1/2”
12.7mm
3/8”
9.5mm
10-40 feet
4-12 meters
1/2”
12.7mm
1/2”
12.7mm
5/8”
15.9mm
1/2”
12.7mm
40-100 feet
13-30 meters
1/2”
12.7mm
1/2”
12.7mm
3/4”
19mm
1/2”
12.7mm
100-150 feet
31-46 meters
3/4”
19mm
1/2”
12.7mm
7/8”
22.2mm
3/4”
19mm
Notice: Never use plastic pipe. Check to confirm whether your
local codes allow copper tubing or galvanized.
Notice: Since some municipalities have additional local codes, it
is always best to consult your local authority and installation code.
Installing a New Main Gas Shut-Off
Each appliance should have its own manual gas shut-off.
A manual main gas shut-off should be located in the vicinity of
the unit. Where none exists, or where its size or location is not
adequate, contact your local authorized installer for installation
or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
checked for leaks by the installer. Testing for leaks on all exposed
connections should be done with leak detection test solution. After
testing is complete, all solution should be cleaned off. On unexposed
connections, a pressure test should be made.
Never use an exposed flame to check for leaks. Fireplace must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test.
Never use an exposed flame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required by
the National Fuel Gas Code that a drip line be installed near the gas
inlet. This should consist of a vertical length of pipe tee connected
into the gas line that is capped on the bottom in which condensation
and foreign particles may collect.
Figure 15
The use of the following gas connectors is recommended:
— ANSI Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
— ANSI Z21.45 Assembled Flexible Appliance Connectors of
Other Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The Commonwealth of Massachusetts requires
that a flexible appliance connector cannot exceed three feet in length.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3.175mm)
N.P.T. plugged tapping, accessible for test gauge connection,
must be placed immediately upstream of the gas supply
connection to the appliance.
2. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will
result in a hazardous condition.
TO CONTROL
VALVE
GAS SUPPLY PLUMBING
MANUAL
SHUT-OFF VALVE
GAS SUPPLY
INLET
1/8 NPT PLUGGED
HOLE FOR
TEST GAGE
3”
MINIMUM
Figure 14
27829-13-1019
Page 17
PLACEMENT OF GLOWING EMBERS AND LAVA ROCK
Placement of the rock wool is for a glowing effect based on the
look you desire.
Place just enough embers on the burner to obtain the glow and a
gold, yellow flame.
WARNING
"Apply loose material per instructions manual. DO NOT
apply extra material or material not supplied with the heater.
Replace only with (Empire Comfort Systems)."
Do not place embers (rock wool) over large ports in rear or front portion of burner.
Rock wool should not be placed in the area of the pilot assembly.
Replacement of loose material (glowing embers) must be purchased
from a dealer of Empire Comfort Systems, Inc. Application of excess
loose material (glowing embers) may adversely affect performance
of the heater.
ROCKWOOL
Ember Placement VFSM - Figure 17
WARNING
All previously applied loose material must be removed prior
to reapplication.
Refer to Parts List, Page 25 to order loose material (rock wool).
Placing Lava Rock in Front of Burner on Fireplace Floor
Spread lava rocks on fireplace floor in front of the burner pan. The
lava rocks are for decorative effect and are not required for fireplace
operation.
WARNING
ROCKWOOL
Ember Placement VFSR - Figure 16
Do not place lava rocks on Burner, logs or rock wool. The
lava rocks should only be placed on the fireplace floor.
OPERATION INSTRUCTIONS/FLAME APPEARANCE
Flames from the pilot (rear right back side of the pan burner) as
well as the main flame should be visually checked as the log set
is installed.
windows or doors to allow odors to dissipate. Any odors remaining
after this initial break-in will be slight and will disappear with
continued use.
In normal operation at full rate after 10 to 15 minutes, the flame
appearance should be sets of yellow flames.
Notice: All flames will be random by design, flame height will go
up and down.
Glowing embers (rock wool) can cover the pan burner in between
the front and middle logs, but very little is necessary to cover this
area. Excess ember material causes the yellow flame to become
orange and stringy. Apply just enough to obtain slow glow and a
gold yellow flame.
Avoid any drafts that alter burner flame patterns. Do not allow fans to
blow directly into fireplace. Do not place a blower inside the burner
area of the firebox. Ceiling fans may create drafts that alter flame
patterns. Sooting and improper burning will result.
Millivolt - Figure 18
During manufacturing, fabricating and shipping, various components
of this appliance are treated with certain oils, films or bonding agents.
These chemicals are not harmful, but may produce annoying smoke
and smells as they are burned off during the initial operation of the
appliance, possibly causing headaches or eye or lung irritation. This
is a normal and temporary occurrence.
The initial break-in operation should last 2-3 hours with the burner
at the highest setting. Provide maximum ventilation by opening
Manual - Figure 19
Do not place embers (rock wool) over large ports in rear or front portion of burner.
Page 18
27829-13-1019
LIGHTING INSTRUCTIONS - VFSR-(16,18,24,30)
FOR YOUR SAFETY READ BEFORE LIGHTING
Warning
If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A.
This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B.
Before lighting smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
C.
Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
What To Do If You Smell Gas
•
Do not try to light any appliance.
•
Do not touch any electrical switch;
do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
•
If you cannot reach your gas supplier, call the fire
department.
LIGHTING INSTRUCTIONS
Notice: For easy access to valve for lighting pilot, remove branch
log and middle log from burner assembly before lighting.
1. STOP! Read the safety information label.
2. Make sure the manual shutoff valve is fully open.
3. This gas log set is equipped with an ignition device (piezo)
which lights the pilot. If piezo ignitor does not light the pilot,
refer to Step 7.
4.
5.
6.
Turn gas control knob clockwise
to the “OFF” position, set the thermostat to the lowest setting and turn ON/OFF
switch to OFF position.
Wait ten (10) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas STOP! Follow “B” in
the safety information label. If you do not smell gas, go to the
next step.
From OFF position, turn the gas control knob counterclockwise
to “Pilot” position. Push in and hold control knob for
5 seconds.
THERMOCOUPLE
7.
With the control knob pushed in, repeatedly push the piezo
ignitor button until pilot is lit (or use a match to light pilot).
8. Continue pushing the control knob in for a further 60 seconds
to prevent the flame detector from shutting off the gas while
the probe is warming up. Release the control knob.
9. Turn gas control knob counterclockwise
to the “ON”
position.
10. After the pilot has been lit for one minute, the burner can be
turned on. Turn the ON/OFF switch to “ON” position or adjust
thermostat to desired setting.
11. If the gas logs will not operate, follow the instructions “To Turn
Off Gas To Appliance” and call your service technician or gas
supplier.
Wait 30 seconds before readjusting the heater when the control
knob has been turned down to a lower setting.
CONTROL
KNOB
PILOT
THERMOCOUPLE
(NATURAL)
THERMOCOUPLE
(PROPANE)
PIEZO
IGNITOR
HI / LO
REGULATOR
TO TURN OFF GAS TO APPLIANCE
1.
Turn control knob clockwise
completely shut off the heater.
27829-13-1019
to OFF position to
2.
If applicable: Turn ON/OFF switch to OFF position and/or set
thermostat (if present) to lowest setting. If applicable: Turn off
all electric power to the heater.
Page 19
LIGHTING INSTRUCTIONS - VFSM-(18,24,30)
FOR YOUR SAFETY READ BEFORE LIGHTING
Warning
If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A.
This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. Before lighting smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
What To Do If You Smell Gas
•
Do not try to light any appliance.
•
Do not touch any electrical switch;
do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
•
If you cannot reach your gas supplier, call the fire
department.
C.
D.
Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1.
2.
3.
4.
5.
6.
STOP! Read the safety information.
Make sure the manual shutoff valve is fully open.
This heater is equipped with an ignition device (piezo) which
automatically lights the pilot.
Refer to Figure 19 for the location of the piezo ignitor and
control knob. Push in gas control knob slightly and turn
to the OFF position.
control knob clockwise
NOTE: Knob cannot be turned to OFF unless knob is pushed
in slightly. Do not force.
Wait ten (10) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas STOP! Follow
the instructions under ‘What To Do If You Smell Gas”. If you
do not smell gas, go to the next step.
From OFF position, push in gas control knob slightly and turn
counterclockwise
to the PILOT position. Push in and
hold control knob for 5 seconds.
NOTE: If you are running the heater for the first time, it will
be necessary to press in the control knob for 30 seconds to
allow air to bleed out of the gas piping.
7.
With the control knob pushed in, push and release the piezo
ignitor button to light the ODS pilot. The pilot is located on the
right rear side of the heater, behind the middle log and in front
of the rear log. If piezo ignitor does not light the pilot, refer to
“Match Lighting Instructions”.
PILOT
THERMOCOUPLE
(PROPANE)
THERMOCOUPLE
(NATURAL)
8.
Hold the control knob in for an additional 10 seconds to prevent
the ODS pilot from shutting off the gas while the thermocouple
is warming up.
9. Release the control knob.
*
If the knob does not pop out when released, stop and
immediately call your service technician or gas supplier.
*
If the ODS pilot will not stay lit after several tries, push
and turn the gas control knob clockwise
to OFF
and wait 15 seconds. Repeat steps 6 through 9.
10. Push in control knob and turn to desired setting (1, 2, 3).
The control knob must be set at either the low or high
position, and the control knob will pop out when positioned
correctly. Do not set the control knob at a position between
pilot (1, 2, 3).
TO TURN OFF GAS TO APPLIANCE
1.
Turn control knob clockwise
completely shut off the heater.
Page 20
to OFF position to
27829-13-1019
PILOT FLAME CHARACTERISTICS
Figures 20 and 22 show a correct pilot flame pattern. The correct
flame will be blue and will extend beyond the thermocouple. The
flame will surround the thermocouple just below the tip. A slight
yellow flame may occur where the pilot flame and main burner flame
meet. Figures 21 and 23 show an incorrect pilot flame pattern.
The incorrect pilot flame is not touching the thermocouple. This will
cause the thermocouple to cool. When the thermocouple cools, the
heater will shut down.
VFSM Pilot
VFSR Pilot
THERMOCOUPLE
THERMOCOUPLE
(PROPANE)
PILOT
THERMOCOUPLE
(NATURAL)
Correct Pilot Flame Pattern - Figure 20
THERMOCOUPLE
THERMOCOUPLE
(PROPANE)
THERMOCOUPLE
(PROPANE)
THERMOCOUPLE
(NATURAL)
If pilot flame pattern is incorrect, as shown in Figure 21:
• See Troubleshooting, page 24.
THERMOCOUPLE
(NATURAL)
Correct Pilot Flame Pattern - Figure 22
PILOT
Incorrect Pilot Flame Pattern - Figure 21
27829-13-1019
PILOT
PILOT
THERMOCOUPLE
(PROPANE)
THERMOCOUPLE
(NATURAL)
Incorrect Pilot Flame Pattern - Figure 23
If pilot flame pattern is incorrect, as shown in Figure 23:
•
See Troubleshooting, page 24.
Page 21
CLEANING AND SERVICING
Cleaning and Maintenance/Pilot
Oxygen Depletion Sensor Pilot
When the pilot has a large yellow tip flame, clean the Oxygen
Depletion Sensor as follows:
1. Clean the ODS pilot by loosening nut B from the pilot tubing.
When this procedure is required, grasp nut A with an open end
wrench.
2. Blow air pressure through the holes indicated by the arrows.
This will blow out foreign materials such as dust, lint and spider
webs. Tighten nut B also by grasping nut A.
CAUTION
Never use needles, wires, or similar cylindrical objects to
clean the pilot to avoid damaging the calibrated ruby that
controls the gas flow.
Annual inspection and cleaning by your dealer or qualified
service technician is recommended to prevent malfunction
and/or sooting.
TURN OFF HEATER AND ALLOW TO COOL BEFORE
CLEANING.
Remove logs, handling carefully by holding gently at each end.
Gloves are recommended to prevent skin irritation from ceramic
fibers. If skin becomes irritated, wash gently with soap and water.
Refer to manual for correct log placement.
PERIODIC CLEANING – Refer to parts diagram for location of
items discussed below.
•
Do not use cleaning fluid to clean logs or any part of heater.
•
Logs - brush with soft bristle brush or vacuum with brush
attachment.
•
Remove loose particles and dust from the burner areas,
controls, piezo covers and grate. Don’t remove media from
inside burner box.
•
Inspect and clean burner air intake hole. Remove lint or particles
with brush. Failure to keep air intake hole clean will result in
sooting and poor combustion.
ANNUAL CLEANING/INSPECTION – Refer to parts diagram for
location of items discussed below.
Figure 24
•
•
•
•
•
•
Page 22
Inspect and clean burner air intake hole. Remove lint or particles
with vacuum or brush. Failure to keep air intake hole clean will
result in sooting and poor combustion.
Inspect and clean all burner ports.
Inspect ODS pilot for operation and accumulation of lint at air
intake holes.
Verify flame pattern and log placement for proper operation.
Verify smooth and responsive ignition of main burner.
Check level of ceramic media in burner. Burner should be full,
up to the level of openings in burner top.
27829-13-1019
WIRING
VFSR Wiring Diagram
Thermostats are not approved on vented decorative appliances.
Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation. Verify proper
operation after servicing.
REMOTE CONTROL RECEIVER /
THERMOSTAT
16", 18", 24" and 30" Gas Logs (Millivolt) thermopile is self powered
gas valve and does not require 120 volts. See Figure 25 to provide
optional wall switch, thermostat, or remote control. Maximum
length of 20 feet of 16 AWG to conductor wires is to be used with
all optional switches.
Use the two leads (black wires) from ON/OFF switch to attach
optional components. Output should be a minimum of 325 millivolts
across TH/TP and TP terminals with ON/OFF switch in the OFF
position.
Check System Operation
Millivolt system and all individual components may be checked with
a millivolt meter 0-1000 MV range.
Remote Receiver -VFSR-(16, 18, 24, 30)
Use the following steps to place the remote receiver adjacent to
the gas valve.
Attention:
1. The remote receiver can not be placed behind the gas valve
and burner assembly.
2. When facing the appliance, the remote receiver must be placed
to the right of the gas valve and burner assembly.
Notice: Do not let remote control receiver come in contact with
burner assembly.
On circulating vent-free firebox, install remote control receiver
behind bottom louver.
Refer to remote control installation and operating instructions for
more details on remote control.
750 Millivolt System
When you ignite the pilot, the thermocouple produces millivolts
(electrical current) which energizes the magnet in the gas valve.
After 30 seconds to 1 minute time period you can release the gas
control knob and the pilot will stay ON. Allow your pilot flame to
operate an additional one (1) to two (2) minutes before you turn the
gas control knob from the PILOT position to the ON position. This
time period allows the millivolts (electrical current) to buildup to a
sufficient level allowing the gas control to operate properly. GAS VALVE
(OPTIONAL) WALL SWITCH
REMOTE / OFF / ON SWITCH
(OPTIONAL) THERMOSTAT
(OPTIONAL) REMOTE CONTROL RECEIVER
OFF / ON SWITCH
BLACK
OFF
THERMOCOUPLE
THERMOCOUPLE
(PROPANE)
(LPG)
ON
BLACK
THERMOPILE
THERMOCOUPLE
(NATURAL)
IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THIS UNIT MUST BE
REPLACED, IT MUST BE REPLACED WITH NO. 18, 150º WIRE OR ITS
EQUIVALENT.
Figure 25
Millivolt Control
The valve regulator controls the burner pressure which should be
checked at the pressure test point. Turn captured screw counter
clockwise 2 or 3 turns and then place tubing to pressure gauge over
test point (Use test point “A” closest to control knob). After taking
pressure reading, be sure and turn captured screw clockwise firmly
to re-seal. Do not over torque. Check for gas leaks.
VFSR
Notice: (Wiring harness located in envelope)
Connect the 2 - 1/4" terminals onto the TH and TH/TP terminals
on valve. Place decorative log to right of the gas valve and burner
assembly. When connecting to remote receiver, cut off 1/4" terminals
from wires attached to ON/OFF switch. Strip wires back about 1/4".
Connect stripped ends into remote receiver.
27829-13-1019
Page 23
TROUBLESHOOTING
SYMPTOMS - POSSIBLE CAUSES AND CORRECTION
1.
2.
3.
4.
5.
6.
When ignitor button is pressed, there is no spark at ODS/
pilot.
a. Ignitor electrode not connected to ignitor cable - Reconnect
ignitor cable.
b. Ignitor electrode positioned wrong - Replace pilot.
c. Ignitor electrode is broken - Replace pilot.
d. Ignitor cable pinched or wet. Keep ignitor cable dry - Free
ignitor cable if pinched by any metal or tubing.
e. Broken ignitor cable - Replace ignitor cable.
f. Bad piezo ignitor - Replace piezo ignitor.
Appliance produces unwanted odors.
a. Appliance burning vapors from paint, hair spray, glues, etc.
- Ventilate room. Stop using odor causing products while
heater is running.
b. Gas leak - Locate and correct all leaks.
Appliance shuts off during use. (Pilot and main burner are
off.)
a. Not enough fresh air is available for ODS/pilot to operate Open window and/or door for ventilation.
b. Low line pressure - Contact local gas company.
c. ODS/pilot is partially clogged - Clean ODS/pilot.
d. Defective thermocouple - Replace pilot.
Appliance shuts off during use. (Pilot stays on.)
a. Low line pressure - Check line pressure to the valve.
b. Defective thermopile - Check pilot flame, check wire
connections, output should be a minimum of 325 millivolts
across TH/TP and TP terminals with ON/OFF switch off.
Gas odor even when control knob is in OFF position.
a. Gas leak - Locate and correct all leaks.
b. Control valve defective - Replace control valve.
When ignitor button is pressed, there is spark at ODS/pilot,
but no ignition.
a. Gas supply turned off or manual shutoff valve closed - Turn
on gas supply or open manual shutoff valve.
b. Control knob not in PILOT position - Turn control knob to
Pilot position.
c. Control knob not pressed in while in PILOT position - Press
in control knob while in PILOT position.
d. Air in gas lines when installed - Continue holding down control
knob. Repeat igniting operation until air is removed.
e. ODS/pilot is clogged - Replace ODS/pilot assembly or get
it serviced.
g. Gas regulator setting is not correct - Replace gas
regulator.
7.
ODS/pilot lights but flame goes out when control knob is
released.
a. Control knob not fully pressed in - Press in control knob
fully.
b. Control knob not pressed in long enough - After ODS/pilot
lights, keep control knob pressed in 30 seconds.
c. Manual Shutoff valve not fully open - Fully open manual
shutoff valve.
d. Thermocouple connection loose at control valve - Hand
tighten until snug, then tighten 1/4 turn more.
e. Pilot flame not touching thermocouple, which allows
thermocouple to cool, causing pilot flame to go out. This
problem could be caused by either low gas pressure or dirty or
partially clogged ODS/pilot - Contact local gas company.
f. Thermocouple damaged - Replace thermocouple.
h. Control valve damaged - Replace control valve.
8. Burner does not light after ODS/pilot is lit.
a. Burner orifice clogged - Clean burner or replace main burner
orifice.
b. Burner orifice diameter is too small - Replace burner
orifice.
c. Inlet gas pressure is too low - Contact qualified service
person.
9. If burning at main burner orifice occurs (a loud, roaring
blow torch noise).
a. You must turn off burner assembly and contact a qualified
service person.
b. Manifold pressure is too low - Contact local gas company.
c. Burner orifice clogged - Clean burner or replace burner
orifice.
10. Logs appear to smoke after initial operation.
a. Vapors from paint or curing process of logs - Problem will
stop after a few hours of operation. Run the heater with the
damper open if you have one, or open a window for the first
few hours.
Log heater is intended to be smokeless. Turn OFF heater
and call qualified service person.
11. Heater produces a whistling noise when main burner is
lit.
a. Turning control knob to HIGH position when main burner is
cold - Turn control knob to LOW position and let warm up
for a minute.
b. Air in gas line - Operate burner until air is removed from
line. Have gas line checked by local gas company.
c. Dirty or partially clogged burner orifice - Clean burner or
replace burner orifice.
12. No gas to pilot.
a. Propane-regulator shut down due to inlet pressure too high
- Verify propane tank regulator is installed and set at 11" to
13" w.c. Replace regulator on heater.
If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the
gas quality or pressure is low, contact your local gas supplier immediately.
Page 24
27829-13-1019
MASTER PARTS DISTRIBUTOR LIST
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater, Hearth and Grills
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com & www.victormfg.com
Parts: Heater, Hearth and Grills
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Parts: Heater, Hearth and Grills
HOW TO ORDER REPAIR PARTS
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distributors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number and Serial Number from the
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following illustration and part list. Be sure to give all this information . . .
Appliance Model Number
Part Description
Appliance Serial Number
Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
27829-13-1019
Page 25
PARTS LIST
Attention: When ordering parts, it is very important that part number and description of part coincide.
Index
No.
Part
No.
Index
No.
Part
No.
REAR LOG SUPPORT (VFS(M,R)-16)
11
20294
VVALVE BRACKET
Description
COMMON PARTS
1
15425
Description
MILLIVOLT SYSTEM (CONT'D)
1
15426
REAR LOG SUPPORT (VFS(M,R)-18)
12
R10405
GAS VALVE - NATURAL
1
15427
REAR LOG SUPPORT (VFS(M,R)-24)
12
R10406
GAS VALVE - Propane
1
15428
REAR LOG SUPPORT (VFS(M,R)-30)
13
26304
PIEZO IGNITOR BRACKET
2
11376
BURNER SUPPORT - LEFT
(VFS(M,R)-(18,24,30))
14
R9761
PIEZO IGNITOR
2
11285
BURNER SUPPORT - LEFT (VFS(M,R)-16)
NS
26331
TUBING - VALVE TO PILOT - Propane
3
P200
ORIFICE FITTING
NS
26330
TUBING - VALVE TO PILOT
REGULATOR - NATURAL
NS
14041
TUBING - PILOT REGULATOR TO
PILOT - NATURAL
NS
26332
TUBING - VALVE TO BURNER
R5668
IGNITOR WIRE
4
P250
ORIFICE - Propane (VFS(M,R)-18)
4
P245
ORIFICE - Propane (VFS(M,R)-24)
4
P265
ORIFICE - Propane (VFS(M,R)-30)
4
P204
ORIFICE - Propane (VFSR-16)
NS
4
P244
ORIFICE - Natural (VFS(M,R)-24)
NS
R5910
4
P256
ORIFICE - NATURAL (VFSR-16)
SWITCH LOG ASSEMBLY (INCLUDES
SWITCH AND WIRE)
4
P243
ORIFICE - NATURAL (VFSR-18)
NS
R11558
OFF/ON SWITCH
4
P211
ORIFICE - NATURAL (VFSR-30)
NS
R5699
WIRE HARNESS
4
P203
ORIFICE - NATURAL (VFSM-18)
4
P209
ORIFICE - NATURAL (VFSM-30)
6
R5170
PILOT - Propane
5
R5675
AIR SHUTTER - Propane
5
R5676
AIR SHUTTER - NATURAL
7
11833
PILOT SHIELD (NATURAL ONLY)
9
17370
BURNER ASSEMBLY (VFS(M,R) -24)
9
12348
BURNER ASSEMBLY (VFS(M,R)-16) Propane
9
12347
BURNER ASSEMBLY (VFS(M,R)-16) NATURAL
9
18838
BURNER ASSEMBLY (VFS(M,R)-18)
9
17386
BURNER ASSEMBLY (VFS(M,R)-30)
22
11370*
GRATE ASSEMBLY (18" MODELS) (2 REQ'D)
22
16178*
GRATE ASSEMBLY (24" & 30" MODELS)
(2 REQ'D)
* Requires 2/Grate ASM of R9628 Clips
MANUAL SYSTEM
6
R5171
PILOT - NATURAL
10
26291
BURNER SUPPORT - RIGHT
14
R9761
PIEZO IGNITOR
16
R2783
CONTROL KNOB
17
15416
VALVE BRACKET
18
R4499
GAS VALVE - Propane
18
R4495
GAS VALVE - NATURAL
19
15494
COVER PLATE
20
R2480
INLET REGULATOR - Propane
20
R2479
INLET REGULATOR - NATURAL
21
15414
REGULATOR MOUNTING BRACKET
NS
R5668
IGNITOR WIRE
NS
12389
CERAMIC MEDIA
NS
15528
TUBING ASSEMBLY - INLET REGULATOR
TO VALVE
NS
R2809
DAMPER CLAMP (INCLUDED IN HARDWARE
PACKAGE)
NS
15529
TUBING - VALVE TO BURNER
NS
15530
TUBING - VALVE TO PILOT
NS
11788
DECORATIVE ROCK (2 REQ’D)
NS
15998
ROCK WOOL (VFS(M,R)-16)
NS
15999
ROCK WOOL (VFS(M,R)-18)
NS
15970
ROCK WOOL (VFS(M,R)-24,30)
6
R3624
PILOT - NATURAL
6
R3623
PILOT - Propane
8
R7063
PILOT REGULATOR (NATURAL ONLY)
10
26321
BURNER SUPPORT - RIGHT (16)
10
26291
BURNER SUPPORT - RIGHT (18,24,30)
NS = Not Shown
MILLIVOLT SYSTEM
Use Only Manufacturer's Replacement Parts. Use of Any Other Parts Could Cause Injury Or Death.
Page 26
27829-13-1019
PARTS VIEW
20
21
22
27829-13-1019
Page 27
WARRANTY
Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the periods specified
below. Hearth products must be installed by a qualified technician and must be maintained and operated safely, in accordance with the
instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All warranty repairs must
be accomplished by a qualified gas appliance technician.
Limited Five-Year Parts & Labor Warranty – All Other Components
(Except Remote Controls, Thermostats, Accessories and Replacement Parts)
Should any part fail because of defective workmanship or material within five years from the date of purchase, Empire will
repair or replace at Empire’s option. Within five years from the date of purchase, Empire will pay reasonable labor to have that
defect repaired at Empire’s option.
Limited One-Year Parts Warranty – Remote Controls, Thermostats, Accessories, and Parts
Should any remote control, thermostat, accessory, or other part fail because of defective workmanship within one year from
the date of purchase, Empire will repair or replace at Empire’s option. Duties Of The Owner
The appliance must be installed by a qualified installer and operated in accordance with the instructions furnished with the
appliance. A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty
period. Ready access to the appliance for service.
What Is Not Covered
Damages that might result from the use, misuse, or improper installation of this appliance.
Travel, diagnostic costs and freight charges on warranted parts to and from the factory.
Claims that do not involve defective workmanship or materials.
Unauthorized service or parts replacements.
Removal and reinstallation cost.
Inoperable due to improper or lack of maintenance.
How To Get Service
To make a claim under this warranty, please have your receipt available and contact your installing dealer. Provide the dealer
with the model number, serial number, type of gas, and purchase verification. The installing dealer is responsible for providing
service and will contact the factory to initiate any warranted parts replacements. Empire will make replacement parts available
at the factory. Shipping expenses are not covered.
If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department,
Empire Comfort Systems Inc., PO Box 529, Belleville, Illinois 62222, or send an e-mail to info@empirecomfort.com with
“Consumer Relations” in the subject line.
Your Rights Under State Law
This warranty gives your specific legal rights, and you may also have other rights, which vary from state to state.
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at info@empirecomfort.com.
If you have a service or repair
question, please contact your dealer.
www.empirecomfort.com
Page 28
27829-13-1019
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising