American Hearth | Surrounds and Fronts for Loft Direct-Vent Fireplaces | Owner Manual | White Mountain Hearth Surrounds and Fronts for Loft Direct-Vent Fireplaces Owner Manual

White Mountain Hearth Surrounds and Fronts for Loft Direct-Vent Fireplaces Owner Manual
INSTALLATION INSTRUCTIONS
FOR USE ONLY WITH DVL(25,33)FP-1 AND DVL(25,33)FP7-2 SERIES FIREPLACES
INSTRUCTIONS MUST BE LEFT WITH THE OWNER FOR FUTURE REFERENCE AFTER INSTALLATION.
SURROUNDS
DECORATIVE FRONT KITS
DS(25,33)66BL-1
DFB(25,33)R(BL,HP,SS)-1
HARDWARE FOR SURROUND
HARDWARE
FRAMING
MEMBER
FOR 3/8” SET-BACK
#8-18 x ½” TRUSS-HEAD SCREWS - QTY 3
USE REAR
PAIR OF
HOLES
FLANGE
TO REAR
FRAMING
BRACKET
BUSHING - QTY 1
3/8”
SET-BACK
BEND TABS TO REAR
The following instructions apply to installation of the
Decorative Fronts and Surrounds.
Figure 1a
Note: The Direct-Vent Fireplace must be installed into
the fireplace cavity with all venting, gas and electrical
connections completed prior to installation of the Surround
and Front assemblies.
Note: All Fronts require the installation of a 4-Sided
Surround as shown in Figure 2.
Securing the Fireplace
1. Installation of the fireplace in the framed out wall opening will require that the side and top flanges of the fireplace face (with glass door removed) be a minimum of
3/8-inch forward from the surface of the finished wall.
See Figure 1a.
2. If needed the framing brackets can be installed as
shown in Figure 1b to allow an additional 1/2-inch (7/8inch total) set back for finishing materials such as tile,
glass or marble.
Note: The framing brackets include two hand-bend tabs
at the top and bottom of the bracket. Depending on which
way the brackets are mounted (Figures 1a and 1b), bend
these tabs rearward to assist in maintaining the proper
combustible clearance to the fireplace sides.
34965-2-0519
FINISHED
WALL SURFACE
(½” THICK SHOWN)
FRAMING
MEMBER
FOR 7/8” SET-BACK
USE FRONT
PAIR OF HOLES
FLANGE
TO FRONT
FRAMING
BRACKET
FINISHED
WALL SURFACE
(½” THICK SHOWN)
7/8”
SET-BACK
BEND TABS TO REAR
Figure 1b
Note: The side framing brackets provided with the fireplace
include mounting holes. In addition, there are two sets of pilot
holes in the sides of the fireplace to mount the framing brackets,
which will allow for various setback positions. Choose the
mounting holes that secure the fireplace forward of the finished
wall material 3/8-inches as recommended in step 1.
Page 1
Installation of Surrounds
Installation of Decorative Front kits
1. Install the upper deflector to the surround as shown in
Figure 2. Secure with three #8-18 x 1/2 PH.HD. screws.
Make sure the deflector is directed upward as shown in
Figure 2.
1. Carefully unpack the Decorative Front assembly. This
kit comes fully assembled.
2. After the Direct Vent Fireplace has been installed with
all required connections completed, install the Surround
by placing the upper surround flange over the top flange
of the fireplace cabinet.
3. Install the Decorative Front to the Insert by aligning the
four extended fingers on the back of the Decorative Front
with the slots located in the side flanges of the Fireplace.
See Figure 3.
3. Center the surround left to right, then swing the legs of
the surround inward to the side flanges of the fireplace.
Lift each surround leg slightly so that the lower retaining
hooks engage the notched out areas in the side flanges.
See Figure 2.
2. To install, a Surround must be secured to the Fireplace.
See Figure 2.
4. If power is connection is needed outside of fireplace,
break knockout Figure 2. Place cord through cutout
and snap bushing in hole.
DEFLECTOR
Figure 3
4. Once the four fingers are started, gently push the Front
assembly inward until it is fully engaged with the Fireplace.
Note: the Decorative Front will set out from the Surround
approximately 2 to 3 inches.
SURROUND
TOP
BUSHING
Figure 2
SWITCH KNOCK-OUT
POWER CORD KNOCK-OUT
Page 2
34965-2-0519
Surrounds
4-Sided Surround
Models and
Finish Options
DS(25,33)66BL
•
Black
Required for use with Eclipse
style fronts.
Decorative
Front Kits
Eclipse
Model and
Finish Options
DFB(25,33)R(BL,HP,SS)
•
Black
•
Hammered Pewter
•
Stainless Steel
Note: Must also use
4-sided surround. Install
surround before installing
decorative front.
34965-2-0519
Page 3
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at info@empirecomfort.com.
If you have a service or repair
question, please contact your dealer.
www.empirecomfort.com
Page 4
34965-2-0519
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising