American Hearth | Reflective Liner Kits for VFLB36FP, VFLB48FP, & VFLB48SP (VBP36LSS, VBP36LKR, VBP36LWR, VBP48LSS, VBP48LBKR, VBP48LBWR, & VBP48BLKR) | Owner Manual | White Mountain Hearth Reflective Liner Kits for VFLB36FP, VFLB48FP, & VFLB48SP (VBP36LSS, VBP36LKR, VBP36LWR, VBP48LSS, VBP48LBKR, VBP48LBWR, & VBP48BLKR) Owner Manual

White Mountain Hearth Reflective Liner Kits for VFLB36FP, VFLB48FP, & VFLB48SP (VBP36LSS, VBP36LKR, VBP36LWR, VBP48LSS, VBP48LBKR, VBP48LBWR, & VBP48BLKR) Owner Manual
INSTALLATION INSTRUCTIONS
For Use On: REFLECTIVE LINER KITS
INSTRUCTIONS MUST BE LEFT WITH THE OWNER FOR FUTURE REFERENCE AFTER INSTALLATION.
REFLECTIVE LINER Kits
VFLB36FP(30,90)0-1
1.
VFLB48FP(30,90)-1
VFLB48SP90-1
VBP48BLKR-1
VBP36LSS-1
VBP48LSS-1 VBP36LKR-1
VBP48LBKR-1
VBP36LWR-1
VBP48LBWR-1
Remove barrier screen assembly from fireplace by lifting up,
slightly and pulling out. See Figure 1.
3.
Remove the burner cover by lifting it up and out. Discard
burner cover for porcelain kits (VBP36LKR, VBP36LWR,
VBP48LBKR, VBP48LBWR, and VBP48BLKR). Keep burner
cover for Stainless kits (VBP(36,48)LSS). See Figure 3.
Figure 1
2.
Remove glass panels around burner. See Figure 2.
Note: VFLB48SP models will have four glass panels.
Figure 3
T
RIGH
TER
CEN
EFT
L
Figure 2
40243-0-0119
Page 1
4.
Remove the inner firebox top by removing five Phillips Truss
Head Screws. See Figure 4.
Note: If a Light Kit is installed: Unhook the wire harness from
the light before removing the inner firebox top. See Figure 5.
Note for VBP(36,48)LSS Liners: Remove plastic coating
protecting stainless steel parts before installing. Use stainless
steel cleaner to remove manufacturing marks or fingerprints.
5.
Place the back liner into the firebox back and secure with
two 10 X 1/2 inch screws. The liner will rest on top of the rear
liner support brackets. See Figure 6.
Note: VBP48BLKR does not include a back liner; skip to step 6.
SCREWS
Figure 4
Figure 5
Page 2
Figure 6
40243-0-0119
Place the left liner on the left side of the firebox. Angle
liner up into place and allow bottom to rest on the left liner
support brackets. Secure the liner with one 10 x 1/2 inch
screw. See Figure 7.
6.
Note: VBP48BLKR will use two 10 x 1/2 inch screws to
secure. See Figure 8.
7.
Place the right liner on the right side of the firebox. Angle
liner up into place and allow bottom to rest on the right liner
support brackets. Secure the liner with one 10 x 1/2 inch
screw. See Figure 9.
Note: VBP48BLKR will use two 10 x 1/2 inch screws to
secure. See Figure 10.
LINER
SUPPORT
BRACKETS
LINER SUPPOR
LINER
SUPPORT
BRACKETS
ER SUPPORT
BRACKETS
RACKETS
SCREW
SCREW
Figure 7
Figure 9
LINER
SUPPORT
BRACKETS
LINER
SUPPORT
BRACKETS
LINER SUPPOR
BRACKETS
NER SUPPORT
BRACKETS
SCREWS
SCREWS
Figure 10
Figure 8
40243-0-0119
Page 3
NOTE: If a decorative front will be installed, install it at this time.
Refer to the instructions provided with the decorative front kit.
8.
Secure the liners in place by reinstalling the inner firebox top
and five screws removed in Step 3. See Figures 4 and 11.
Note: If a light kit is installed, reconnect the wire harness to
the light. See Figure 5.
10. For VBP(36,48)LSS Models: Reinstall the burner cover
removed in Step 3. See Figure 3.
For other Models: Install new burner cover included in the
porcelain kit to replace burner cover removed in Step 3.
See Figure 3.
Note: Make certain burner cover lays flat in fireplace.
Burner cover should not bow.
11. Reinstall glass panels removed in Step 2. See Figure 2.
Note: Verify glass panels are level.
12. Reinstall the Barrier Screen onto the fireplace by lining up the
tabs with the slots in the firebox. Push the barrier screen toward
the unit and lower it slightly to lock in place. See Figure 14.
Figure 11
9.
For Porcelain Liner Kits only: Burner box may have tabs
bent away from the burner box. Bend these tabs flush with
the burner box. These tabs will allow the burner cover to fit
around the burner box.
Note: These are not the tabs that hold the short glass
panels in place. See Figures 12 and 13.
Figure 14
Figure 12
Figure 13
Page 4
40243-0-0119
2
1
2
3
4
INDEX NO.
PART NUMBER
DESCRIPTION
VBP36LKR
VBP36LWR
VBP36LSS
1
40262BL
40262WT
40263
2
29487BL
29487WT
32686
Liner Side (2 Required)
3
40252BL
40252WT
N/A
Burner Cover Assembly
4
R2737
R2737
R2737
#10 X 1/2 inch Screw (4 Required)
INDEX NO.
1
PART NUMBER
VBP48LBKR
VBP48LBWR
VBP48LSS
32684BL
32684WT
32685
Liner Rear
DESCRIPTION
Liner Rear
2
29487BL
29487WT
32686
Liner Side (2 Required)
3
40254BL
40254WT
N/A
Burner Cover Assembly
4
R2737
R2737
R2737
#10 X 1/2 inch Screw (4 Required)
INDEX NO.
PART NUMBER
VBP48BLKR
DESCRIPTION
1
N/A
2
40264BL
Liner Side (2 Required)
3
40253BL
Burner Cover Assembly
4
R2737
#10 X 1/2 inch Screw (4 Required)
40243-0-0119
Liner Rear
Page 5
This page intentionally left blank.
Page 6
40243-0-0119
This page intentionally left blank.
40243-0-0119
Page 7
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at info@empirecomfort.com.
If you have a service or repair
question, please contact your dealer.
www.empirecomfort.com
Page 8
40243-0-0119
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising