Hanna Instruments | HI144 | Owner Manual | Hanna Instruments HI144 Owner Manual

Hanna Instruments HI144 Owner Manual
Operational Guide
Technical Service
This instrument is factory calibrated, but it is generally
recommended to have all thermometers recalibrated at least
once a year.
For an accurate recalibration, contact your nearest Hanna
Customer Service Center.
Initial Operation
The logger is supplied complete with a CR2032 lithium battery.
Open the battery compartment cover (see “Battery Replacement”
section for details), insert the battery with the + sign facing
up and tighten back the compartment cover.
The display will show the “PC” message
to indicate that the logger needs to be
programmed through a PC.
If the starting type was set to PC Start, then the Start key will
become active. Click to Start.
If the starting type was set to Button Start, then the logger
display will indicate that the logger button has to be pressed
to start logging. Keep the button pressed for about 3 seconds.
3 sec.
Wall Installation
The logger is supplied complete with wall cradle and lock
(mounting materials as screws and dowels are not included).
Position the wall cradle at the desired location and fix it to the
wall with proper screws.
INSTRUCTION MANUAL
HI144 T-Logger
If the starting type was set to Date/Time Start, then the
logger will automatically start logging at the programmed time.
Button Functions
Pressing the logger button will give different outputs depending
on the logger status.
• If the logger is in “WAIT TO LOG” status, then pressing
the button will navigate through current measurement, high
and low alarm thresholds.
Insert the logger into the cradle and secure it with the supplied
lock.
Startup
In order to communicate with the logger, the application
software must be installed on your PC.
Connect HI144002 communication cradle to your computer
through a USB port, and place the HI144 on the cradle.
• If the logger is in “LOG” or “LOG DONE” status, then
pressing the button will navigate through current measurement, maximum and minimum recorded values.
Certification
• If you keep the button pressed, after 2 seconds the display
will show alternatively (toggle every 2 seconds) the high
and low alarm thresholds.
Run the application software. The yellow LED on the cradle
blinks to indicate that the communication is active. Do not
remove the logger while the LED is blinking.
The following operating parameters can be set:
• Measurement Unit: °C or °F
• Starting Type: PC Start, Button Start or Date/Time Start
(hh:mm:ss)
• Logging Method: Wrap Around Memory, until memory is full (at
8000 samples) or number of samples (a maximum of 8000)
• Logging Interval: from 1 minute to 24 hours (1 minute
resolution)
• High and Low Alarm thresholds
• Logger Password
Click on the Program key to program the logger with the
selected options.
keep pressed,
then after 2 sec.
toggle every
2 seconds
Notes:
• If an alarm threshold has not been
set, then the logger will display the
“diS” (disabled) message.
• If an alarm condition has occurred during logging, then
in the “LOG” or “LOG DONE” status the corresponding
alarm indication (“ALARM HI” or “ALARM LO”) will blink.
All Hanna Instruments products conform to CE
European Directives.
Disposal of Electrical & Electronic Equipment. The product
should not be treated as household waste. Instead hand it over
to the appropriate collection point for the recycling of electrical
and electronic equipment which will conserve natural resources.
Disposal of waste batteries. This product contains batteries, do not dispose of them with other household waste.
Hand them over to the appropriate collection point for recycling.
Ensuring proper product and battery disposal prevents potential negative consequences for the environment and human
health. For more information, contact your city, your local
household waste disposal service, the place of purchase or go
to www.hannainst.com.
Recommendations for Users
Before using Hanna Instruments products, make sure that they
are entirely suitable for your specific application and for the
environment in which they are used. Any variation introduced
by the user to the supplied equipment may degrade the meter’s
performance. For yours and the instrument safety do not use or
store the instrument in hazardous environments.
IST144 05/19
Warranty
HI144 logger and communication cradle are warranted for
two years against defects in workmanship and materials when
used for their intended purpose and maintained according to
instructions. This warranty is limited to repair or replacement free
of charge. Damages due to accident, misuse, tampering or lack of
prescribed maintenance are not covered. If service is required,
contact your local Hanna Instruments Office. If under warranty,
report the model number, date of purchase, serial number
and the nature of the problem. If the repair is not covered by
the warranty, you will be notified of the charges incurred. If
the instrument is to be returned to Hanna Instruments, first
obtain a Returned Goods Authorization (RGA) number from the
Technical Service department and then send it with shipping
costs prepaid. When shipping any instrument, make sure it is
properly packaged for complete protection.
All rights are reserved. Reproduction in whole or in part is
prohibited without the written consent of the copyright owner.
Hanna Instruments reserves the right to modify the design, construction or appearance
of its products without advance notice.
Thank You
Thank you for choosing a Hanna Instruments product. Please
read this instruction manual carefully before using the meter.
For more information about Hanna Instruments and our
products, visit www.hannainst.com or e-mail us at sales@
hannainst.com.
For technical support, contact your local Hanna Instruments
Office or e-mail us at tech@hannainst.com
Find your local Hanna Instruments Office on www.hannainst.com
Preliminary Examination
Remove the instrument from the packing and examine it carefully
to make sure that no damage has occurred during shipping.
Notify your nearest Hanna Costumer Service Center if damage
is observed.
Note: Save all packing material until you are sure that the
meter works correctly. Any damaged or defective items
must be returned in their original packing material together
with the supplied accessories.
Each HI144 is supplied with:
• CR2032 lithium battery
• Wall cradle
• Lock
• Instruction manual
Each HI144-10 is supplied with
• HI144
• HI144002 USB communication cradle
• CR2032 lithium battery
• Wall cradle
• Lock
• Instruction manual
PC Software
The HI92144 PC application software supports communication
between the logger and a PC. The PC compatible software is
available for download at http://software.hannainst.com.
Select the product code and click Download Now.
After download is complete, use the setup.exe file to install
the software.
General Description
Data transfer to PC
Battery Replacement
HI144 is a temperature data logger with internal NTC sensor
able to memorizes 8000 logs. The user can program the device
or download the logged data through the HI144002 USB
communication cradle.
The main features of HI144 temperature logger include:
• Up to 8000 logged samples
• Selectable logging interval, from 1 minute to 24 hours
• Selectable measurement unit, °C or °F
• Programmable high and low alarms
• Logger password
• Logging through PC Start, Button Start or Data/Time Start
• Non-volatile logging parameters and data storage
• Storage and display of minimum or maximum measured values
• Battery level indicator on display
• IP65 protection
To download logged data, remove the logger from its installation
and place it on HI144002 communication cradle connected to
your PC through a USB port.
Each time the battery is installed, the logger enters reset status
and displays the “PC” message.
The memory content can then be downloaded from the instrument to the PC using the Windows® compatible application
software offered by Hanna Instruments.
This software allows you to use the powerful capabilities of most
spread sheet programs (e.g. Excel©, Lotus 1-2-3©) and to make
any elaboration available (e.g. graphics, statistic analysis, etc.).
The user-friendly online help and clear messages will support
you throughout.
During data transfer the yellow LED on the cradle blinks to
indicate that the communication is active. Do not remove
the logger while the LED is blinking.
Then it starts to calculate remaining battery life and displays
current battery level through a 4-tag indicator.
When the last tag (empty battery) starts blinking, the battery
level is below 5%. It is recommended to change the battery
with a new one.
Battery replacement must only take place in a safe area and
using the appropriate battery type (CR2032 3V lithium battery).
Note: It is recommended to use a new battery for
replacement, otherwise the battery level indication may
not be reliable.
Specifications
Range
-30.0 to 70.0 ºC / -22.0 to 158.0 ºF
Resolution
0.1°C / 0.1°F
Accuracy
Calibration
LCD Functional Description
1
2
When the battery needs to be replaced, open the battery
compartment cover at the back using a small coin. Turn
counter-clockwise to open.
3
±0.4 °C (-20 to 60 °C); ±0.6 °C (outside)
±0.7 °F (-4 to 140 °F); ±1.1°F (outside)
Factory calibrated
Data Logging Up to 8000 samples
Logging Interval User selectable, from 1 minute to 24 hours
Battery Type
1 x CR2032 3V lithium battery
Battery Life
2 years
Environment
0 to 50 ºC (32 to 122 ºF) RH max. 100%
Dimensions 60 x 37 x 17 mm (2.4 x 1.5 x 0.7’’)
Weight
29.4 g (1 oz.)
(with batteries)
Casing Ingress
Protection
IP65 (watertight)
Rating
8
7
6
1. “WAIT TO LOG”: Waiting to start logging
2. “LOG”: Logging in progress
3. “LOG DONE”: Logging completed
4. High and Low alarm values
5. Measurement unit
6. Start by pressing the logger button
7. Battery level indicator
8. Maximum and minimum logged values
5
4
Insert the new battery with the + sign facing up, tighten back
the compartment cover and program the instrument.
Note: Dispose the depleted battery (Li) according to local
regulations.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising