Hanna Instruments | HI8010 | Owner Manual | Hanna Instruments HI8010 Owner Manual

Hanna Instruments HI8010 Owner Manual
Probe Maintenance
To obtain the highest accuracy for measurements
it is important to follow these tips:
• Calibration is only as good as the buffers being used.
The pH buffers value change over time once the sachets
are opened. Fresh buffer should be used for each
calibration.
• The probe should be rinsed with purified water each
time before pla cing in buffer or sample to be tested.
• When the meter is not in use it is important to add
several drops of storage solution to a sponge in the
protective cap to keep the probe hydrated. If storage
solution is not available, then pH 4.01 or pH 7.01 buffer
can be used.
• For improved accuracy it is recommended to calibrate
in two points. It is important to use buffers that bracket
the expected value of the sample to be tested. For
example, if the expected value is pH 8, the meter should
be calibrated using pH 7.01 and pH 10.01 buffers.
• It is important to calibrate and measure samples at the
same temperature. A dramatic change in temperature
between buffer solutions and samples to be tested will
give inaccurate readings.
Battery Replacement
When the battery becomes weak, the instrument
automatically switches the display off. It is recommended to
replace the battery immediately.
Replacement must only take place in a safe area using an
alkaline 9V battery. Remove the battery cover and replace
the old battery with a new one, while paying attention to
its polarity.
Note: After changing the battery, recalibrate the meter.
Recommendations for Users
Before using Hanna products, make sure that they are
entirely suitable for your specific application and for the
environment in which they are used. Operation of these
instruments may cause unacceptable interferences to
other electronic equipment. Take all necessary steps to
correct such interferences. Avoid touching the probe at
all times. Any variation introduced by the user to the
supplied equipment may degrade the instrument’s EMC
performance. Do not put the instrument in a microwave
oven to avoid burns or damage to equipment. Do not use
or store the instrument in hazardous environments.
Warranty
This meter is warranted for two years against defects
in workmanship and materials when used for their
intended purpose and maintained according to instructions.
Electrodes are warranted for six months. This warranty is
limited to repair or replacement free of charge. Damage
due to accidents, misuse, tampering or lack of prescribed
maintenance are not covered. If service is required, contact
the dealer from whom you purchased the instrument.
If under warranty, report the model number, date of purchase, serial number and the nature of the problem. If the
repair is not covered by the warranty, you will be notified
of the charges incurred. If the instrument is to be returned
to Hanna Instruments, first obtain a Returned Goods Authorization Number from the Customer Service department and
then send it with shipment costs prepaid. When shipping
any instrument, make sure it is properly packaged for
complete protection.
Hanna Instruments reserves the right to modify the design,
construction, or appearance of its products without advance notice.
Accessories
Code
HI98501
HI1230B
HI1332B
HI70300M
Description
Digital thermometer
(range: -50.0 to 150.0 ˚C)
Plastic-body, double junction, gelfilled, combination pH electrode with
BNC connector and 1 m cable
Plastic-body, double junction, refillable,
combination pH electrode with BNC
connector and 1 m cable
Electrode storage solution, 230 ml
bottle
HI7004M
pH 4.01 buffer solution, 230 ml bottle
HI7006M
pH 6.86 buffer solution, 230 ml bottle
HI7007M
pH 7.01 buffer solution, 230 ml bottle
HI7009M
pH 9.18 buffer solution, 230 ml bottle
HI7010M
pH 10.01 buffer solution, 230 ml bottle
General cleaning solution, 230 ml
bottle
Refilling electrolyte solution for double
junction electrodes, 3.5M KCl 30 ml
bottle, 4 pcs.
HI7061M
HI7082
HI740029P
IST8010V
06/16
9V battery, 10 pcs.
INSTRUCTION MANUAL
HI8010
Portable pH Meter
Thank You
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using
the instrument.
For more information about Hanna and our products, visit
www.hannainst.com.
For technical support, contact your local Hanna office or
email us at tech@hannainst.com
Find your local Hanna office at www.hannainst.
Preliminary Examination
Remove the instrument from the packing material and
examine it carefully to make sure that no damage has
occurred during shipment. If noticeable damage is found,
notify your dealer.
HI8010 comes supplied complete with:
• HI1230B pH electrode
• calibration screwdriver
• 9V battery (1 pc.)
• instruction manual
• certificate
Note: Save all packing material until you are sure that
the instrument functions correctly. Any defective items
must be returned in the original packing together with
the supplied accessories.
Functional Description
BNC socket for pH
electrode
Liquid Crystal
Display (LCD)
Calibration Procedure
Offset (pH7)
& slope
(pH4/10)
Rotary knob
trimmers
for pH
calibration
Trimmer
for manual
temperature
setting
Specifications
Range
Resolution
Accuracy
(@25 °C/77 °F)
Calibration
Temperature
Compensation
Probe
Environment
Power Supply
Dimensions
Weight
0.00 to 14.00 pH
0.01 pH
±0.01 pH
manual, two point, through
trimmers
manual, through trimmer from 0 to
100 °C (32 to 212 °F)
HI1230B double junction, gel-filled.
pH electrode with BNC connector
and 1 m cable (included)
0 to 50 °C (32 to 122 °F);
RH max 95 %
9V battery (1 pc.)
approx. 100 hours of continuous use
185x82x53 mm (7.3x3.2x2.1’’)
265 g (9.3 oz.)
For better accuracy, a frequent calibration of the meter is recommended. Moreover, the instrument should be calibrated:
a) when the pH electrode or the battery is replaced;
b) at least once a month;
c) after testing aggressive chemicals;
d) where extreme accuracy is required.
Preparation
• Pour small quantities of pH 7.01 (HI7007) and pH
4.01 (HI7004) solutions into two clean beakers.
• For accurate calibration use two beakers for each
solution: the first one for rinsing the electrode, the
second one for calibration.
• For accurate readings, use pH 7.01 (HI7007) and pH
4.01 (HI7004) if samples to be measured are acidic,
or pH 7.01 (HI7007) and pH 10.01 (HI7010) for
alkaline measurements.
• If calibration to NBS standards is required, use
pH 6.86 (HI7006) instead of pH 7.01 and pH 9.18
(HI7009) instead of pH 10.01.
Procedure
• Remove the protective cap from the electrode, rinse
and immerse it in pH 7.01 buffer and stir gently. Wait
a couple of minutes for the reading to stabilize.
• Measure the solution temperature with a HI98501,
e.g. 20 °C.
• Set the rotary knob to the °C position to display the
manual temperature setting and adjust the °C trimmer
until the LCD shows the measured temperature.
• Set the rotary knob to the pH position, wait for the
reading to stabilize and with a small screwdriver adjust
the AP trimmer until the LCD shows the pH value at
the above temperature (see pH vs. temperature chart
on the buffer bottle).
• Rinse and immerse pH electrode and thermometer in
pH 4.01 or pH 10.01 buffer (2nd calibration point); stir
gently.
• Wait a few minutes, then adjust the pH trimmer until
the LCD shows the pH value at the noted temperature
(see pH vs. temperature chart on the buffer bottle).
Operational Guide
• Slide off the battery compartment cover on the back
of the meter and install the supplied 9V battery, while
paying attention to its polarity.
• Connect the pH electrode to the BNC socket on the top
of the meter and remove the electrode protective cap.
• Immerse the electrode (at least 4 cm/1.5’’) and an
accurate thermometer (eg. HI98501) in the sample to
be tested, as close as possible one to the other.
• Turn the rotary knob to the °C position to display the
temperature setting. With the provided screwdriver,
adjust the °C trimmer to read on the LCD the
temperature measured by the thermometer.
• Turn the rotary knob to the pH position, shake the
electrode briefly and allow the reading to stabilize. The
display will show the pH value compensated for the
manually adjusted temperature.
• After measurements, switch the meter OFF by turning
the rotary knob to the OFF position, disconnect the
electrode from the meter and store it with a few drops
of HI70300 solution in the protective cap.
Notes:
Before taking measurements, make sure the meter is
calibrated.
If the electrode has been left dry, soak the tip in
HI70300 storage solution for at least one hour to
reactivate it.
For a faster response time when using refillable
electrodes, unscrew the refill hole cap.
• If measurements are taken in different samples
successively, it is recommended to clean the electrode
thoroughly to eliminate cross-contamination. After
cleaning, rinse the electrode with some of the sample
to be measured.
All rights are reserved. Reproduction in whole or in part is
prohibited without the written consent of the copyright owner,
Hanna Instruments Inc., Woonsocket, Rhode Island, 02895, USA.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising