Hanna Instruments | BL983321-0,BL983321-1 | Owner Manual | Hanna Instruments BL983321-0,BL983321-1 Owner Manual

Hanna Instruments BL983321-0,BL983321-1 Owner Manual
Instruction Manual
BL 983321-0
BL 983321-1
Panel-Mounted
TDS Indicators &
Controllers
Dear Customer,
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using
these instruments. This manual will provide you with the
necessary information for correct use of these instruments.
If you need additional technical information, do not hesitate
to e-mail us at tech@hannainst.com or view our worldwide
contact list at www.hannainst.com.
PRELIMINARY EXAMINATION
Remove the instrument from the packing material and
examine it carefully to make sure that no damage has
occurred during shipping. If there is any damage, notify
your Dealer or the nearest Hanna Customer Service Center.
Each meter is supplied with:
• Mounting brackets
• Instruction manual
Note: Save all packing material until you are sure that the
instrument functions correctly. All defective items must
be returned in the original packing with the supplied
accessories.
WARRANTY
GENERAL DESCRIPTION
These instruments are guaranteed for two years against defects in
workmanship and materials when used for their intended purpose and
maintained according to instructions. Electrodes and probes are guaranteed
for six months. This warranty is limited to repair or replacement free of
charge.
Damages due to accidents, misuse, tampering or lack of prescribed
maintenance are not covered.
If service is required, contact the dealer from whom you purchased the
instrument. If under warranty, report the model number, date of purchase,
serial number and the nature of the problem. If the repair is not covered
by the warranty, you will be notified of the charges incurred. If the
instrument is to be returned to Hanna Instruments, first obtain a Returned
Goods Authorization number from the Technical Service department and
then send it with shipping costs prepaid. When shipping any instrument,
make sure it is properly packaged for complete protection.
BL983321-0 and BL983321-1 are TDS indicators and
controllers with a relay output designed for simplicity of use in
a wide range of applications.
Connections and wiring to probe, power supply and contacts
are made via the terminal blocks on the rear panel.
The probe is easy to clean and requires little maintenance.
Other features include: automatic temperature compensation
of readings, single point calibration, overtime control system,
multi-colour LED for indicating if the meter is in measurement/
dosing/alarm condition, possibility to set (Off-Auto-On switch)
dosing action mode.
Two models are available:
• BL 983321-0 powered at 12 Vdc
• BL 983321-1 powered at 115 or 230 Vac
Recommendations for Users
Before using these products, make sure that they are entirely suitable for the environment
in which they are used. Operation of these instruments in residential areas could cause
unacceptable interferences to radio and TV equipment. Any variation introduced by the user
to the supplied equipment may degrade the instrument’s EMC performance. To avoid
electrical shock, do not use these instruments when voltages at the measurement surface
exceed 24 Vac or 60 Vdc. To avoid damages or burns, do not perform any measurement in
microwave ovens.
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner, Hanna Instruments
Inc., Woonsocket, Rhode Island, 02895 , USA.
SPECIFICATIONS
Range
0.00 to 19.99 ppm
Resolution
0.01 ppm
Accuracy (@ 25 °C / 77 °F)
±2% f.s.
TDS conversion factor
0.5
Probe
HI 7634-00 EC/TDS probe (not included)
Temp.Compensation Automatic from 5 to 50 °C (41 to 122 °F);
ß=2%/ºC
Calibration
Manual, through CAL trimmer
Dosing Contact Maximum 2A (fuse protected), 250 Vac, 30 Vdc
Contact close when measure > setpoint
Setpoint
Adjustable, from 0 to 19.99 ppm
Overtime
Adjustable, typically from 5 to approx. 30 minutes
Power Consumption
10 VA
Installation Category
II
Power supply:
External (fuse protected)
BL983321-0
12 Vdc
BL983321-1
115/230 Vac ; 50/60 Hz
Dimensions
83 x 53 x 99 mm (3.3 x 2.1 x 3.9”)
ASSEMBLING VIEW
ACCESSORIES
HI 7634-00
HI 7061M
HI 7061L
HI 710005
HI 710006
HI 710012
HI 710013
HI 710014
HI 731326
HI 740146
EC/TDS probe
Probe cleaning solution, 230 mL bottle
Probe cleaning solution, 500 mL bottle
12 Vdc power adapter, US plug
12 Vdc power adapter, European plug
12 Vdc power adapter, Australian plug
12 Vdc power adapter, South African plug
12 Vdc power adapter, UK plug
Calibration screwdriver (20 pcs.)
Mounting brackets
FUNCTIONAL DESCRIPTION
Front panel
1. Liquid Crystal Display
2. Switch for selecting dosing mode:
• OFF = dosing disabled
• Auto = automatic dosage, depending on setpoint value
• ON = dosing always active
3. MEAS key to set the instrument to measurement mode
4. SET key to display and set the setpoint value
5. SET trimmer to adjust the setpoint value
6. CAL trimmer
7. 3-colour LED indicator:
• Green = meter in measurement mode
• Orange/Yellow = dosing in progress
• Red, blinking = indicates an alarm condition
OPERATIONS
Rear panel
1. Connections for EC probe
2. Power supply terminal:
• for BL983321-0 model: 12 Vdc adapter
• for BL983321-1 model: 115 Vac or 230 Vac option
3. This contact acts as a switch for driving the dosing system
(e.g. dosing pump)
4. Not used contact
5. Jumper for enabling (jumper in) or disabling (jumper
removed) the overtime control
6. Trimmer for overtime setting (typically from 5 to 30 minutes)
All external cables connected to the rear panel
should end with cable lugs.
A circuit breaker (rated 6A max.) must be
connected in close proximity to the equipment,
and in a position easy to reach by the operator,
for disconnection of the instrument and of all
the devices connected to the relays.
REAR PANEL CONNECTIONS
Terminals #1: Probe
• Connect the HI 7634-00 probe by following the colour
indication of the wires.
Terminals #2: Power Supply
• Model BL983321-0: connect the 2 wires of a 12 Vdc
power adapter to the terminals +12 Vdc and GND.
• Model BL983321-1: connect a 3-wire power cable to the
terminals while paying attention to the correct earth (PE),
line (L) and neutral (N1 for 115 V or N2 for 230 V) contacts.
Terminals #3: Dosing Contact
• This contact drives the dosing system according to the
selected setpoint.
Note: The setpoint has a typical hysteresis value comparable
to the meter’s accuracy.
Terminals #4: Not Used Contact
Overtime system: jumper (#5) and trimmer (#6)
• This system allows the user to set a maximum dosing
period, by adjusting the rear trimmer from 5 (min) to
approx. 30 (max) minutes.
• When the set time is exceeded, any dosing action stops,
the LED indicator on the front panel will blink Red and the
LCD will show the “TIMEOUT” warning message. To exit
the overtime condition, set the OFF/Auto/ON switch to
OFF position, and then to Auto again.
• For disabling the overtime feature, simply remove the
jumper from the rear panel.
Note: The overtime system works only if the OFF/Auto/ON
switch is in Auto position.
OPERATING THE METER
Before proceeding make sure that:
• the meter has been calibrated;
• the setpoint value has been properly adjusted;
• all rear panel wiring and selections are correct;
• the OFF/Auto/ON switch is in the desired position.
Install or immerse the probe in the solution to be monitored,
then press the MEAS key (if necessary).
The LCD will show the TDS (ppm) value. The LED indicator will
light up Green when the meter is in measurement mode and
dosing is not active, while it will light up Orange/Yellow
signaling that a dosing action is in progress.
CALIBRATION
To calibrate the meter, proceed as follows:
• ensure the meter is in measurement mode;
• use a solution with a TDS value higher than 13 ppm and
immerse the probe;
• shake briefly and wait for reading to stabilize;
• adjust the CAL trimmer to read the TDS value of the
solution on the LCD.
SETPOINT
Press the SET key: the display will show the default or
previously adjusted value, together with the ”SET“ indication.
Using a small screwdriver adjust the SET trimmer until the
desired setpoint value is displayed.
After 1 minute the meter automatically returns to the normal
mode; if not, press the MEAS key.
PROBE MAINTENANCE
To improve the probe’s performance and prolong its life, it is
recommended to clean it regularly.
• Immerse the tip of the probe in HI 7061 Cleaning
Solution at least for one hour.
• If a more thorough cleaning is required, brush the metal
pins with very fine sandpaper.
• After cleaning, rinse the probe with tap water and
recalibrate the meter.
• When not in use, clean the probe before storing it.
Hanna Instruments reserves the right to modify the design, construction
or appearance of its products without advance notice.
ISTBL3321 04/13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising