Miele | WWB020 | Owner Manual | Miele WWB020 Owner Manual

Miele WWB020 Owner Manual
Program selection
ĺĺ Sort the laundry by color and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺĺ Pre-treat stains and badly soiled areas (see the Miele
website for advice).
1 Control panel
2 Sensor buttons – temperature
for selecting the wash temperature.
3 Sensor buttons – spin speed
for selecting the spin speed.
4 Sensor buttons – extra options
for the various extra options that can be
added to the wash programs.
5 Indicator lights   


=
Water intake or drain fault
=
Excess detergent used

=
Hygiene info

=
Flashes: Laundry can be added
Lights up: Door is locked
6 CapDosing sensor buttons

=

Fabric care (e.g., fabric softener,
proofing agent)
=

Additives (e.g., detergent enhancers)
=
Detergent (for the main wash only)
7 Time display
After the program has started, the program duration will appear in the display in
hours and minutes.
8 Sensor buttons   
for the Delay Start function
9 Start/Stop sensor button
Touching the Start/Stop sensor button
starts the selected program or cancels
a program that has already started. The
sensor button flashes slowly as soon as
it is possible for a program to be started
and then lights up constantly after the
program has started.
10 Optical interface
for service technicians
11 Program selector
for selecting programs and for switching
off. The washing machine is switched on
when you select a program, and switched off by turning the program selector
to the  position.
–– Use the Express program for small,
lightly soiled loads.
–– Modern detergents make it possible
to wash at lower temperatures (e.g.,
70°F/20°C). Using the corresponding
temperature settings will save energy.
–– Use the correct amount of detergent
in accordance with the manufacturer’s
recommendations. Reduce the amount
of detergent with smaller loads (approx.
1/3 less than the amount recommended
can be used when washing a half load).
–– Select the highest possible spin speed
for the wash program to save energy in
the subsequent tumble dryer cycle.
1
2
3
4
4
Detergent dispenser drawer
Control panel
Drain filters
Door
Selecting extra options
The selection of extra options available for the wash program lights up dimly.
ĺĺ Touch the sensor button for
the required extra option. It will
then light up brightly.
尝尝Chlorine bleach is a very aggressive
substance. It can cause damage to the
colors and fibers of textiles. Only use chlorine bleach on suitable textiles.
Chlorination must be activated in the settings before chlorine bleach is first used.
The extra option Pre-wash must not be
selected.
ĺĺ Pour max. ¼ cup (60 ml) of chlorine bleach into the   chamber.
The chlorine bleach is added automatically 10 minutes before the end of the main
wash.
Using powder detergent
The detergent drawer contains an insert for
liquid detergent in the  compartment.
This insert must be removed to use powder
detergent.
Using powder detergent in the
 compartment is not possible.
CapDosing
Three different types of capsule are available:
Contents:

Fabric care (e.g., fabric softener,
proofing agent)
 Additives (e.g., detergent enhancers)

Detergent (for the main wash only)
Each cap contains the correct amount for
one wash cycle.
Switching on CapDosing
ĺĺ Touch the sensor button for the cap you
want to use
Sensor button



Tip: You can select multiple extra options for a
wash program.
OPERATION
–– Make use of the maximum load that
the wash program can accommodate.
–– When smaller amounts of laundry are
washed, the washing machine’s automatic load control system will reduce
the amount of water and energy used.
3
ĺĺ Pull out the detergent drawer and add
detergent to the compartments.
  Chlorine bleach for removing
stains or liquid detergent for the
pre-wash
Detergent for the main wash,

including Soak if selected
 /  Fabric softener, liquid starch, or
caps
ĺĺ Shut the door.
Environmentally friendly washing
Using chlorine bleach
Follow the manufacturer’s instructions on
the packaging.
Selecting a temperature and spin speed
The wash program’s pre-set temperature and spin speed
light up brightly. The choice of temperatures and spin
speeds selectable for the wash program light up dimly.
ĺĺ Touch the sensor button for
the temperature desired. It will
then light up brightly.
ĺĺ Touch the sensor button for
the spin speed desired. It will
then light up brightly.
ĺĺ Take hold of the door and pull
it open.
ĺĺ Loosely load the laundry in the
drum.
ĺĺ Make sure that no items are
caught between the door and
the seal.
Detergent drawer
This washing machine requires
high-efficiency (HE) detergent
ĺĺ Turn the program selector to
the required program.
The estimated wash time is shown
on the time display and the pre-set temperature and spin
speed light up on the control panel.
Check the drum for pets or foreign objects before loading it with laundry.
Closing the door
There are several options for adding detergent to the washing machine.
Dispensing chlorine bleach
2. Loading the washing machine
Opening the door
4. Adding detergent
The washing machine is switched on by turning the program selector to a wash program.
Cap
for

for

for

5. Starting a program
ĺĺ Touch the flashing Start/Stop sensor button.
The door will lock (the  symbol will appear
on the control panel to show this) and the
program will start.
Extra options
Selecting Delay Start
ĺĺ Select the program required.
ĺĺ Touch the 
sensor button.
Heavy soiling
For laundry that is very heavily soiled.
The extended wash duration enhances
the stain-removing effect.
With Delay Start, you can delay the start of
a program from 30 minutes up to a maximum of 24 hours..
6. Program end
The time display shows :. The  symbol will remain lit up on the control panel.
The door is locked in the Anti-crease phase.
ĺĺ Touch the Start/Stop sensor button.
ĺĺ The door unlocks and the  symbol on
the control panel goes out.
ĺĺ Pull open the door.
ĺĺ Remove the laundry.
Extra options are selected and deselected using the relevant sensor buttons on
the control panel.
Light soiling
For slightly soiled textiles that are not
stained. The wash duration is reduced.
ĺĺ Touch the  or  sensor button repeatedly until the required Delay Start time
appears on the time display.
–– In the case of settings below 10 hours,
the Delay Start time changes in
increments of 30 minutes
–– In the case of settings above 10 hours,
the Delay Start time changes in
increments of 1 hour
ĺĺ Touch the flashing Start/Stop sensor button.
The Delay Start process starts and counts
down on the time display.
Tip: Delay Start cannot be selected in the
Drain/Spin or Proofing programs.
尝尝Check that all items have been removed from the drum.
ĺĺ Check the folds
in the door seal
for any small
articles, such as
buttons, which
might be lodged
there.
ĺĺ Turn the program selector to the  position. This switches the washing machine
off.
ĺĺ If applicable, remove the used cap from
the detergent drawer and leave the drawer slightly open.
Delay Start
Pre-wash
For laundry with large amounts of dirt,
e.g., dust and sand.
Buzzer
A buzzer sounds at the end of the program. The buzzer will sound until the
washing machine is switched off. The
buzzer volume can be changed.
en - US
2
coins, paper clips, etc.) can
cause damage to garments and
components in the machine.
Using detergent could result in an excessive build-up of foam!
At the end of the program
The  symbol lights up on the control
panel, : appears on the time display,
and the drum occasionally rotates.
ĺĺ Touch the Start/Stop sensor button.
The door will be unlocked.
ĺĺ Reach under the recessed grip and pull
the door open.
Note: Leave the door slightly open to
allow the drum to dry.
ĺĺ When the program has ended, turn the
program selector to .
1
尝尝Foreign objects (e.g. nails,
For safety reasons, spinning is not possible
until the machine has been prepared for use
for the first time. To activate the spinning
function, you must run a wash program
without laundry and without detergent.
Running the first program
ĺĺ Turn on the water supply.
ĺĺ Turn the program selector to Normal.
The washing machine is now switched on
and the temperature hot+ lights up on the
control panel.
ĺĺ Touch the Start/Stop sensor button.
The program starts and the  symbol lights
up on the control panel.
3. Selecting a program
ĺĺ Empty all pockets.
time, ensure that it is correctly installed
and connected.
Please read the separate Operating Instructions supplied with the appliance.
WWB 020
1. Preparing the laundry
尝尝Before using the machine for the first
The ball valve is activated at the same time.
The ball valve prevents detergent escaping from the suds container into the sump
during a wash program, thus making maximum use of the detergent.
Delay Start/Extra options
M.-Nr. 10 980 040/01
Washing
DELAY START/EXTRA OPTIONS
Operation
WASHING
Initial commissioning
Cleaning the detergent dispensing
drawer
Miele
UltraWhite
Miele
UltraColor
Normal


Wrinkle-free
–

Drain only: Set spin speed to .
Make sure you select the appropriate spin speed.

Sanitize

–
Handwash
–
–
Dress Shirts


Express
–

Darks/Denims
–

Extra White


Outdoor
–
–
Proofing
–
–
Miele
Cap 
Miele
Cap 
Miele
Cap 
–


–
, , 
–
, , 
–
–
–
–

–


–





–


–
–



–
–
 = Recommended; – = Not recommended
 = Sportswear;  = Downs;  = Outdoor;  = WoolCare;  = SilkCare;  = Fabric Softener;
 = Proofing;  = Booster
PROGRAM GUIDE

–
Washing at low temperatures and the use
of liquid detergent can lead to a build-up
of bacteria in the detergent dispensing
drawer.
ĺĺ Clean the entire drawer at regular intervals for hygiene reasons, even if you are
using the TwinDos system exclusively.
ĺĺ Pull out the
detergent
dispenser drawer
until a resistance
is felt.
ĺĺ Press down the release button and, at
the same time, pull the drawer completely
out of the machine.
Removing and cleaning the insert for
liquid detergents
An insert for liquid detergents is located in
the compartment of the detergent dispenser drawer.
ĺĺ Remove the
insert. Clean the
insert thoroughly
with warm water.
Cleaning the  compartment
The  compartment has a siphon for
better dispensing of the chlorine bleach.
ĺĺ Remove the
release catch.
ĺĺ Remove and
clean the siphon.
ĺĺ Pull the siphon
out of the 
chamber
ĺĺ Clean all parts and the detergent drawer
with warm water.
Cleaning the detergent dispenser
drawer housing
ĺĺ Use a bottle brush to remove detergent residues and limescale from the jets
inside the detergent dispenser drawer
housing.
Cleaning the drum (hygiene info)
Washing at low temperatures and/or using
liquid detergent can cause bacteria and
unpleasant odors to build up in the washing
machine.
Use the Normal program to clean the
machine. This should be done at the latest
when the
 indicator light comes on.
To switch off the fault messages: Switch the washing machine off with the  button.
The messages will appear at the end of the program and when the washing machine is switched on, and need to be confirmed with the OK sensor button.
Problem/Fault message
Possible cause and solution
The control panel remains
There is no power to the machine.
dark.
ĺĺ Check whether the plug is plugged in.
ĺĺ Check whether the fuse has tripped.
The washing machine has switched off automatically to
save energy.
ĺĺ Switch the washing machine on again by turning the
program selector.
 and  appear alternately The door is not closed properly. The door lock could not
engage.
on the time display.
ĺĺ Close the door again.
ĺĺ Start the program again. If the fault message appears
again, contact Technical Service.
The fault indicator light
The water intake is blocked or restricted.
 lights up, and  and 
ĺĺ Check whether the water supply is turned on properly.
ĺĺ Check whether the intake hose is kinked.
appear alternately on the
time display, and the buzzer ĺĺ Check whether there is sufficient water pressure.
sounds.
The filter in the water intake is blocked.
ĺĺ Clean the filter (see the Operating Instructions).
The fault indicator light
The drain is blocked or restricted.
 lights up, and  and  
The drain hose has been fixed too high.
appear alternately on the
ĺĺ Clean the filter and the pump.
time display, and the buzzer ĺĺ The maximum drain height is 1 m.
sounds.
The fault indicator light
The water protection system has reacted. The washing
machine is switched off.
 lights up, and  and 
ĺĺ Close the water supply.
appear alternately on the
time display, and the buzzer ĺĺ Contact Technical Service.
sounds.
 and  appear alternately There is a fault.
on the time display and the ĺĺ Disconnect the washing machine from the power supply, either by unplugging the machine or by disconnecbuzzer sounds.
ting it at the breaker
ĺĺ Wait at least 2 minutes before reconnecting the washing machine to the electricity supply.
ĺĺ Then switch the washing machine on again.
ĺĺ Restart the program.
If the fault message appears again, contact Technical
Service.
Problem/Fault message
 lights up
Possible cause and solution
The program selector was moved to a different position
after the program had started.
ĺĺ Turn the program selector back to the original
position.
The program has been interrupted.
ĺĺ Open the door.
ĺĺ Close the door. Close the door.
The indicator light  lights Excessive foam has built up during washing.
ĺĺ Use less detergent next time and follow the manufactuup.
rer’s instructions on dosage given on the packaging.
The indicator light  lights A temperature program above 140°F (60°C) has not been
run for a long period of time.
up.
ĺĺ In order to prevent bacteria and unpleasant odors building up in the machine, run the Normal program using
Miele washing machine cleaner or universal powder
detergent.
The door cannot be pulled
The drum is locked during a program.
open during a program.
ĺĺ Touch the Start/Stop button and cancel the program.
The program is canceled, the door will unlock, and you
will be able to pull it open.
There is still water in the drum and the machine is unable
to drain.
ĺĺ Clean the drain filter and the drain pump (see the operating instructions).
After the program is canTo protect the user against scalding, the door cannot
be opened if the suds temperature is higher than 130°F
celed, flashing bars
 ...  ...  ... appear on (55°C).
ĺĺ Wait until the temperature in the drum has decreased
the time display.
and the bars have stopped flashing on the time display.
 and  appear alternately The door lock has jammed.
ĺĺ Contact Technical Service.
on the time display.
Quick Guide
Washer
WAS TUN, WENN …
Miele recommended detergents
The Miele detergents have been developed by Miele especially for the Miele washing
machine. You can order the Miele detergents from Miele’s online store.
Frequently asked questions
CLEANING AND CARE
Full load (17.6 lb/8 kg)
Cleaning and care
Delicates
max.; fast; medium; slow; 
Drain/Spin
Detergent
Programs
Cold
Small load (5.5 lb/2.5 kg)
Performance outerwear (e.g., jackets and trousers) made from membrane
fabric.
Treating microfiber fabric, ski wear, or table linens/drapes made from
mainly synthetic fibers to provide a finish which is resistant to water and
dirt.
fast; medium; slow; ; 
warm+
Proofing
Outdoor
warm+; warm; cold
medium; slow; ; 
Small load (5.5 lb/2.5 kg)
Full load (17.6 lb/8 kg)
For white textiles made of cotton or linen without special hygiene requirements.
max.; fast; ; 
Extra White
hot+
Small load (4.4 lb/2 kg)
Black and dark garments made from cotton, mixed fibers, and denim.
fast; medium; slow; ; 
Darks/Denims
warm+; warm; cold
Half load (7.7 lb/3.5 kg)
Cotton textiles that have hardly been worn or are only very lightly soiled.
Selecting the Lightly soiled extra option will reduce the washing time by
10 minutes.
fast; medium; slow; ; 
Express
warm+; warm; cold
Pre-treat collars and cuffs depending on the level of soiling.
medium; slow; ; 
hot+; hot; warm+; warm; cold
For fine textiles which are only suitable for hand washing.
Small load (4.4 lb/2 kg)
Dress Shirts
Handwash
warm+; warm; cold
fast; medium; slow; ; 
Small load (4.4 lb/2 kg)
Full load (17.6 lb/8 kg)
Cotton or linen fabrics with direct skin contact or for which special hygiene
requirements apply.
max.; fast; ; 
Sanitize
Sanitize
Small load (6.6 lb/3 kg)
For fine textiles made from synthetic fibers.
medium; slow; ; 
Delicates
hot+; hot; warm+; warm; cold
Synthetic or mixed fiber fabric, or wrinkle-free cotton.
fast; medium; slow; ; 
hot+; hot; warm+; warm; cold
Cotton, linen, and mixed fiber textiles made of both cotton and linen.
Half load (8.8 lb/4 kg)
Wrinkle-free
hot+; hot; warm+; warm; cold
Normal
Temperature
max.; ; 
Spin speed
Laundry type
Full load (17.6 lb/8 kg)
Program guide
These short instructions are not a substitute for the Operating Instructions supplied with
the appliance! Please read the Operating Instructions supplied with your washing machine
before using it for the first time and take note of the IMPORTANT SAFETY INSTRUCTIONS, as well as the full descriptions on how to use your appliance.
en - US
M.-Nr. 10 980 040
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising