Sonance | AS68RS | Guide | Sonance AS38RS Guide

Sonance AS38RS Guide
SONANCE ARCHITECTURAL SERIES
®
AS38RS AND AS68RS PLASTER SHIM QUICKSTART GUIDE
Box Contents
(1) Quickstart guide
#4 x 3/4” Wood Screw(s)
(1) Plaster Shim 1/16” thickness
a. (1) for Discreet
Discreet or Medium
b. (3) for Medium
Set of mud ring screw(s) (#6-32 PH x 1 1/4”)
Speaker Installation Screws (#6-32 FH x 1 3/4”)
a. (6) for Discreet
a. (3) for Discreet
b. (12) for Medium
b. (4) for Medium
93303 Medium AS Plaster Shim
1. Sanding Shield Shim
2. Speaker Shim
3. DOS Mud Ring Shim
5
4. Medium Round Mud Ring Shim
5. Medium Square Mud Ring Shim
*Break off for Round
1
93302 DOS Plaster Shim
2
4
3
2
1
*Cut Here
*Cut Here
SHIM INSTALLATION
(Discreet size shown in example)
1
Using a philips screw driver, remove the sanding
shield and set aside for later use. Discard the
removed screw to replace with the longer 3/4”
screw provided.
(Note: Medium will have 3 of these screws)
2
Remove the paint shield by pulling carefully. The
back of the paint shield has adhesive. Save for
later use!
Page 1
4
3
Remove the four mud dam screws with a philips
screw driver. (Note: Medium will have 12 screws)
Sanding shield removed.
6
5
Attach the desired number of plaster shims to
the mud dam using the longer screws provided.
This step makes it easier to install the shims and
mud dam in the ceiling.
Mud dam removed.
7
8
PAINT SHIELD
SANDING SHIELD
*SHIM
*SHIM
#4 x 3/4” wood screw (provided)
*2 SHIMS ARE SHOWN, USE THE SAME NUMBER AS MUD RING SHIMS
Re-install the mud dam and shim sub-assembly
as shown.
Page 2
Using the #4 screw provided, align the sanding
shield, paint shield, and the same number of
sanding shield shims as mud dam shims into a
sub-assembly.
9
Sanding shield sub-assembly.
10
This phase of the installation is complete. Save
the speaker shim for installation of speaker after
plaster and paint is complete.
11
After the plaster is applied and sanded, remove
the sanding shield and discard. Leave the paint
shield until ready to install the speaker.
12
With paint shield in place, finish paint, then
remove the paint shield.
SPEAKER INSTALLATION
13
Remove the sanding shield support.
14
When using AS38RS/BPS6 or AS68RS/BPS8
System, switch to high pass ON. High pass switch
is located on the back of the crossover cover.
Switch high pass to OFF when choosing full
range and no BPS6 or BPS8.
Page 3
15
Add the appropriate number of speaker shims
and install the speaker. Connect the negative
wire to the black spring terminal and the positive
wire to the red spring terminal.
16
Using the provided longer speaker installation
screws, apply Loctite to screws and screw
speaker to mounting platform.
17
For wiring diagrams and detailed eManual
scan the QR code or visit www.sonance.com/
in-wall-in-ceiling/architectural-series/
discreet-opening-system
The leveling ring is for fine adjustment. If
necessary adjust the magnetic grille leveling ring
with a screwdriver and install magnetic grille.
See grille painting instructions.
©2015 Sonance. All rights reserved.
Sonance and Architectural Series are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice.
For the latest Sonance product specification information, visit our website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA
(949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (949) 492-7777
www.sonance.com
33-7441 REV A
Page 4
06.26.17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising