Sonance | Fire-Rated Deep Backcan for In-Ceiling VP (Round & Square) | manual | Sonance Fire-Rated Shallow Backcan for In-Wall VP (Rectangle)*not compatible with Large VP Manual

Sonance Fire-Rated Shallow Backcan for In-Wall VP (Rectangle)*not compatible with Large VP Manual
I N S TA L L AT I O N I N S T R U C T I O N S
F I R E - R A T E D
( L I S T E D )
SHALLOW & DEEP BACKCANS
FOR
SONANCE
SPEAKERS
Introduction
Installation in a Wall or Ceiling
Thank you for purchasing the Sonance model 92807 shallow
(in-wall) or model 92808 deep (in-ceiling) fire-rated speaker
backcan.
N OT E : T H E I N S TA L L AT I O N P R O C E D U R E I S T H E S A M E F O R
S H A L LO W A N D D E E P B AC KC A N M O D E L S.
• The Intertek Listed* fire-rated shallow speaker backcan is
a component in the Sonance In-Wall Speaker System
(WHI Design Listing DII/PV 60-08), comprised of an
Intertek Listed fire-rated shallow metal backcan (Sonance
model # 92807), a Sonance Flex bracket (available separately) and a Sonance in-wall speaker (or equivalent
speaker) or a metal coverplate to protect the exposed
opening.
• The Intertek Listed* fire-rated deep speaker backcan is a
component in the Sonance In-Ceiling Speaker System
(WHI Design Listing DII/PV 60-09), comprised of an
Intertek Listed fire-rated deep metal backcan (Sonance
model # 92808), a Sonance Flex bracket (available separately) and a Sonance in-ceiling speaker (or equivalent
speaker) or a metal coverplate to protect the exposed
opening.
1. Determine the location for the speaker according to the
speaker’s instruction manual.
2. Run speaker wire to the speaker location.
N OT E :
A LWAY S C H E C K LO C A L B U I L D I N G
BEFORE RUNNING WIRES THROUGH WALLS.
CODES
3. Open one of the knockouts in the Backcan and install one
of the Snap2it™ wire clamps into the open knockout.
N OT E :
A SECOND SNAP2IT™ WIRE CLAMP IS
I N S TA L L AT I O N S .
INCLUDED
FOR
D A I S Y- C H A I N E D
A S E C O N D K N O C K- O U T O N T H E B A C KC A N W I L L N E E D
TO B E R E M O V E D F O R T H I S T Y P E O F I N S TA L L AT I O N .
4. Attach the Backcan to the studs/joists through the
pre-drilled holes in the Backcan flange using a minimum
of four (4) #8 x 1¼-inch long screws, one applied to
each corner. See Figure 1.
N OT E : T H E I N C L U S I O N O F A S O N A N C E F L E X B R A C K E T
S O N A N C E I N -WA L L O R I N - C E I L I N G S P E A K E R
AND
( O R E Q U I V A L E N T S P E A K E R ) , O R A M E TA L C O V E R P L AT E TO
P R OT E C T T H E E X P O S E D O P E N I N G I S R E Q U I R E D I N T H I S
A S S E M B LY TO A C H I E V E T H E 1 - H R F I R E - R E S I S TA N C E R AT I N G .
Compatible Speaker Models
Sonance fire-rated shallow & deep speaker backcans can be
used with all Sonance in-wall and in-ceiling speaker models
EXCEPT FOR THE FOLLOWING MODELS:
• All Sonance Virtuoso® in-wall (rectangular) speakers
®
• All Sonance Ellipse speakers
• All Sonance Cinema ® series speakers (LCR1/2 and
SUR1/2)
Use at least
four screws
F IGURE 1: ATTACHING
THE
B ACKCAN
TO STUDS / JOISTS .
®
• Sonance Cinema Ultra II LCR, SUR, Cinema SUB and
Cinema TWO SUB
®
• Sonance Silhouette I and II
5. Insert speaker wire through the Snap2it™ clamp and into
the backcan. Leave enough slack to connect the speaker.
Box Contents
The shipping box contains the following:
continued on page 2
(1) Intertek Listed Sonance Fire-Rated Backcan
(2) Snap2it™ wire clamps
1
FIRE-RATED (LISTED) SHALLOW & DEEP BACKCANS FOR SONANCE IN-WALL AND IN-CEILING SPEAKERS
6. Attach a Sonance Flex bracket or Sonance Architectural
Series mounting platform (appropriate for the speaker
model being installed) over the backcan opening in the
exact speaker mounting location according to the directions in its instruction manual. Drive at least 4 drywall
screws into the studs/joists, directly through the Flex
bracket wings and the Backcan flange. See Figure 2.
9. Follow the instructions included with the speaker for the
remainder of the installation, or install a metal coverplate
to close the Backcan opening.
Backcan
Flex bracket
Flex bracket
wing
Use at least
four screws
Flex bracket
wing
F I G U R E 2 : A T TA C H I N G T H E F L E X B R A C K E T
B AC KC A N O P E N I N G
OVER THE
7. Cut a hole in the gypsum board that matches the opening
in the Flex bracket or Architectural Series bracket.
N OT E : G Y P S U M B O A R D W A L L A S S E M B LY
CONSISTING
O F A N Y G Y P S U M B O A R D W A L L A S S E M B LY, O N E - H O U R
R AT E D I N A C C O R D A N C E W I T H A S T M E 1 1 9 , U L 2 6 3 ,
N F PA 2 5 1 , O R C A N / U L C S 1 0 1 .
8. Install the gypsum board over the Backcan so that the hole
is aligned with the bracket opening. See Figure 3.
Position drywall
opening over
Flex bracket
opening
F I G U R E 3 : I N S TA L L I N G
2
DRYWALL OVER THE
B AC KC A N
*See Intertek Directory of Listed Building Products at:
http://etlwhidirectory.etlsemko.com/WebClients/ITS/DLP/
Products.nsf/$$Search?OpenForm
FIRE-RATED (LISTED) SHALLOW & DEEP BACKCANS FOR SONANCE IN-WALL AND IN-CEILING SPEAKERS
LIMITED FIVE (5) YEAR WARRANTY
Sonance warrants to the first end-user purchaser that this Sonance-brand product (“Product”), when purchased from an
authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated below.
Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new
or remanufactured Product or a reasonable equivalent.
EXCLUSIONS
TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY SONANCE. ALL OTHER
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTY OF
FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. No one
is authorized to make or modify any warranties on behalf of Sonance.
The warranty stated above is the sole and exclusive remedy and Sonance’s performance shall constitute full and final satisfaction
of all obligations, liabilities and claims with respect to the Product. IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR
CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM
THE PRODUCT, ANY BREACH OF THIS WARRANTY OR OTHERWISE.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state.
Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations
may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied warranties is
limited to period of Sonance’s express warranty.
Your Product Model and Description: Fire-rated Backcan
Warranty Period for this Product: Five (5) years from the date on the original sales receipt or invoice or other satisfactory proof
of purchase.
Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is non-transferable, applies only
to the initial installation of the Product, does not include installation of any repaired or replaced Product, does not include
damage to allied or associated equipment which may result for any reason from use with this Product, and does not include
labor or parts caused by accident, disaster, negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker,
excessive heat or cold or humidity, outdoor installation), or from service or repair which has not been authorized by Sonance.
Obtaining Authorized Service: To qualify for the warranty, you must contact your authorized Sonance Dealer/Installer or call
Sonance Customer Service at (800) 582-0772 within the warranty period, must obtain a return merchandise number (RMA),
and must deliver the Product to Sonance shipping prepaid during the warranty period, together with the original sales receipt,
or invoice or other satisfactory proof of purchase.
3
©2008 Sonance. All rights reserved. Sonance, Sonance Architectural Series, Sonance Virtuoso, Sonance Ellipse, Sonance Cinema,
and Sonance Silhouette are registered trademarks of Dana Innovations.
Due to continuous product improvement, all specifications are subject to change without notice.
For the latest Sonance product specification information visit our website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673
USA 949.492.7777 • FAX: 949.361.5151
www.sonance.com
33-5148
110708Final
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising