Central Machinery 8 in. 5 Speed Bench Drill Press Owner's Manual
Central Machinery 62520 is a versatile drill press suitable for various drilling tasks. It features a powerful motor that delivers ample torque for drilling through different materials, including wood, metal, and plastic. The variable speed control allows you to adjust the drilling speed based on the material and the desired outcome. The drill press also comes with a depth stop for precise drilling depths, ensuring consistent results. Additionally, the sturdy cast-iron base provides stability during operation, minimizing vibrations and enhancing accuracy.
PDF
Download
Document
Advertisement
Advertisement
Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. REV 17a Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected] When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2015 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Table of Contents SAFETY Safety ......................................................... 2 Specifications ............................................. 6 Setup .......................................................... 6 Operation .................................................... 8 Maintenance .............................................. 12 Parts List and Diagram .............................. 14 Warranty .................................................... 16 WARNING SYMBOLS AND DEFINITIONS SETUP This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. OPERATION IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. KEEP GUARDS IN PLACE and in working order. MAINTENANCE 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area. 6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. 8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. Page 2 For technical questions, please call 1-888-866-5797. Item 62520 General Tool Safety Warnings (continued) 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. 10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. 11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. 16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons. 18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. 19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. MAINTENANCE 12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. SAFETY (at full load) 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. SETUP NAMEPLATE AMPERES EXTENSION CORD LENGTH ƍ ƍ ƍ ƍ 13. DON’T OVERREACH. Keep proper footing and balance at all times. OPERATION Table A: RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) Item 62520 For technical questions, please call 1-888-866-5797. Page 3 Grounding Instructions SAFETY TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS: 110-120 VAC Grounded Tools: Tools with Three Prong Plugs 1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. SETUP 2. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician. 3. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. OPERATION 4. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. 5. Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. 6. Repair or replace damaged or worn cord immediately. Grounding Pin 125 VAC 3-Prong Plug and Outlet (for up to 125 VAC and up to 15 A) 7. This tool is intended for use on a circuit that has an outlet that looks like the one illustrated above in 125 VAC 3-Prong Plug and Outlet. The tool has a grounding plug that looks like the plug illustrated above in 125 VAC 3-Prong Plug and Outlet. 8. The outlet must be properly installed and grounded in accordance with all codes and ordinances. 9. Do not use an adapter to connect this tool to a different outlet. Drill Press Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Drill Press 1. Wear eye protection. 2. Do not wear gloves, necktie, or loose clothing. MAINTENANCE 3. Clamp workpiece or brace against column to prevent rotation. 4. Use recommended speed for drill accessory and workpiece material. 5. The included chuck key is specially designed to be self-ejecting, reducing the risk of ejecting at high speed. Only use the included chuck key or an identical replacement key. 6. DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED. Moving guards must move freely and close instantly. Page 4 7. The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Only use safety equipment that has been approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area. 10. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. For technical questions, please call 1-888-866-5797. Item 62520 12. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 13. Avoid unintentional starting. Prepare to begin work before turning on the tool. 14. To prevent FIRE, do not install a larger EXOELQWKLVLWHPƍVEXOEKROGHUWKDQ listed in the specifications chart. 15. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. 16. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints • Crystalline silica from bricks and cement or other masonry products • Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) 17. WARNING: The cord of this product contains lead and/or di (2-ethylhexyl) phthalate (DEHP), chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 18. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SETUP 11. Industrial applications must follow OSHA guidelines. SAFETY Drill Press Safety Warnings (continued) Vibration Safety 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Use tools with the lowest vibration when there is a choice between different processes. 4. Include vibration-free periods each day of work. 5. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. For technical questions, please call 1-888-866-5797. MAINTENANCE SAVE THESE INSTRUCTIONS. Item 62520 OPERATION This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: Page 5 Specifications SAFETY Electrical Rating 1209$&+]$ Spindle Speeds 620, 1100, 1720, 2340, 3100 RPM 5 Speeds Table Tilt 45° left and right Swing 8" Spindle Stroke 2" Spindle Taper B16 Chuck Capacity ± PP Worklight Bulb Size (EDVH9: Setup - Before Use: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SETUP TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting OPERATION Secure the tool to a supporting structure before use. Before assembly, bolt the Base to a flat, level, solid workbench capable of supporting the weight of the drill press and any workpieces. Verify that installation surface has no hidden utility lines before drilling or driving screws. Assembly Column to Base Column (8) MAINTENANCE 1. Place Column (8) on the Base (1) and align holes in the Column with holes in the Base. Bolt (5) Spring Washer (4) Washer (3) 2. Attach using Bolt (5), Spring Washer (4), and Washer (3) in each hole through the Column and into the Base. Base (1) Figure A: Column to Base Connection Page 6 For technical questions, please call 1-888-866-5797. Item 62520 Table Support Column 1. Loosen the Pivot Lever (51). Pivot Lever (51) 2. Slide the Table Support (52) over the Column. SAFETY Table Support (52) SETUP 3. Tighten the Pivot Lever to secure the Table Support in place. Figure B: Installing Table Support Headstock and Feed Handles Headstock (39) 2. With assistance, lift the Headstock above the Column, and gently slide it down the Column as far as it will go. Make sure the Headstock slides completely onto the Column. Set Screws (9) 3. Align the Headstock with the Base, and tighten the two Set Screws to secure the Headstock in place. 4. Thread the Feed Handles (6) into the Feed Seat (7) and tighten them. Feed Seat (7) Feed Handle (6) OPERATION 1. Loosen the two Set Screws (9) on the right side of the Headstock (39) so they will stay clear while installing it. Figure C: Installing Headstock and Feed Handles 1. Loosen the Pivot Lever and slide the Table up the Column to within 6" of the Spindle (73). Tighten the Pivot Lever. 5. Use the Feed Handles to gently lower the Spindle so it is just entering the opening in the top of the Chuck. 2. Open the jaws of the Chuck (74) to their maximum, using the supplied Chuck Key. 6. Examine the Chuck from all sides to be sure that it is properly aligned with the Spindle. 3. Put a piece of scrap wood on the table to protect the Chuck nose. 7. Using the Feed Handles, insert the Spindle all the way into the Chuck, pressing the Chuck nose hard against the piece of scrap wood on the Table to secure the Chuck into place. 4. Ensuring all parts are thoroughly clean, dry and burr free, place the Chuck with its open jaws on the scrap wood, directly under the Spindle. Item 62520 For technical questions, please call 1-888-866-5797. Page 7 MAINTENANCE Installing the Chuck Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED. Moving guards must move freely and close instantly. Table Adjustment SETUP 1. Adjust the Table (54) by loosening the Pivot Lever (51), moving the Table, and tightening the Pivot Lever. Table (54) Column 2. Tilt the Table by loosening the Angle Bolt (55) and tilting to the required angle. The angle can be read using the Angle Scale (53). 3. TO ENSURE THAT THE DRILL IS ENTIRELY PERPENDICULAR TO THE TABLE, insert a straight round bar (not included) in the Chuck (72), place a square on the Table and bring it up to the round bar. Adjust the angle as needed. Pivot Lever (51) Angle Bolt (55) under Table OPERATION CAUTION! To prevent injury from unexpected Table movement, tighten Angle Bolt and Pivot Lever after adjustment. Figure D: Table Adjustment Setting a Drilling Depth Located on the left side of the Headstock (39) is the depth feed adjustment assembly, which allows drilling a series of holes to the same depth using one setting. Lock Nut (57B) Pointer (56) 1. Lower the drill (with the power OFF) so that it contacts the material and hold in that position. Adjustment Nut (57A) Scale MAINTENANCE 2. Screw down the Adjustment Nut (57A) on the Stop Rod (58) until the gap between the underside of the Nut and the Drill Stop face equals the depth of the hole required. Refer to Figure E: Drill Depth Adjustment. depth gap Drill Stop Stop Rod (58) 3. Screw down the Lock Nut (57B) against the Adjustment Nut to lock setting. Note: Alternatively, drilling depth for a one-time procedure can be determined by lowering the drill (with the power OFF) until it contacts the work, noting the position of the Pointer (56) on the Scale, turning the drill ON, and drilling to the required depth using the Scale as a guide. Page 8 Figure E: Drill Depth Adjustment For technical questions, please call 1-888-866-5797. Item 62520 Changing Drill Speed 3. Consult the chart below and position the V-Belt on the Pulleys (16, 62) according to the desired drill speed. 1. Open the Pulley Cover. 2. Loosen the Motor Tension Knob (10) on the Headstock (39), and move the Motor (14) towards the Headstock to relieve tension on the V-Belt (60). 4. When the Belt has been correctly positioned, tighten it by pushing the Motor away from the Headstock until the Belt deflects by approximately 1/2" at its center when using reasonable thumb pressure. Lock this position in with the Motor Tension Knob. SAFETY Before changing drill speeds, make sure the machine is switched OFF and UNPLUGGED. Deflection Distance Lamp (33) Motor Tension Knob (10) SETUP Figure G: Belt Deflection Note: If the belt is too long to be properly tensioned, it must be replaced. Light Bulb (40) Figure F: Motor Tension Knob location Spindle Motor 1100 RPM Spindle 1720 RPM Motor Spindle Motor 2340 RPM Spindle Motor 3100 RPM Spindle Motor Figure H: Drill Speed Table The table above shows the belt arrangements for given drill speeds. A full chart is also located on the inside of the pulley cover. Light Bulb Installation 3. Install a new Light Bulb of the same type and rating. (EDVH9: 2. Remove the old Light Bulb from the Lamp (33) and dispose of it properly. WARNING! TO PREVENT SERIOUS INJURY FROM FIRE: Do not install a different style Light Bulb or a Light Bulb with a higher wattage rating. MAINTENANCE 1. To prevent injury, allow the old Light Bulb (40) to cool completely first. Drill Bit Installation 1. Insert the drill bit into the jaws of the Chuck approximately 1", ensuring that the jaws do not touch the flutes of the drill bit. Item 62520 2. Before tightening the Chuck, ensure that the drill bit is centered within the jaws. 3. Tighten the Chuck securely with the included Chuck Key. For technical questions, please call 1-888-866-5797. OPERATION 620 RPM Page 9 Workpiece and Work Area Set Up SAFETY 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 9. FOR SMALL MATERIALS that cannot be clamped to the table, use a drill press vise. Make sure the vise is clamped or bolted to the table. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working. 10. WHEN DRILLING COMPLETELY THROUGH WOOD, position a piece of scrap wood between the material and the table to prevent splintering on the underside of the material as the drill breaks through. The scrap piece of wood must make contact with the left side of the column. Securely clamp the other end of the scrap wood to the table. Also, set the depth of the drill so that the drill will not come in contact with the table - or align the table so that the hole in its center is in line with the drill bit. 3. Secure loose workpieces using a vise or clamps (not included) to prevent movement while working. 4. There must not be objects, such as utility lines, nearby that will present a hazard while working. 5. Make sure the table height and position is set so that the drill travel range is sufficient for the material to be drilled. SETUP 6. Make sure the work is securely clamped. That is, held in a drill vise, or bolted to the table. Never hold the material with your bare hands while drilling. Severe personal injury may be caused if the material is flung out of the operator’s hand. 7. IF THE MATERIAL IS IRREGULARLY SHAPED and cannot be laid flat on the table, it should be securely blocked and clamped. Any tilting, twisting or shifting will result not only in a roughly drilled hole but also increases the chances of damage to the drill. OPERATION 8. FOR FLAT WORK, lay the piece on to a wooden base and clamp it down firmly against the table to prevent it from turning. Figure I: Bracing workpiece against column MAINTENANCE Page 10 For technical questions, please call 1-888-866-5797. Item 62520 General Operating Instructions 2. Plug the Power Cord into an electrical outlet. 3. Turn the Drill Press on. 5. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. MAINTENANCE OPERATION SETUP 4. Pull down on the Feed Handles and slowly drill the hole into the workpiece. WARNING! If the drill bit grabs and spins the workpiece, do not attempt to stop the spinning with your hands. Step back, and turn the drill press off. Wait for the spindle to stop turning before dislodging the workpiece. SAFETY 1. Bring the drill bit down with the Feed Handle to where the hole is to be drilled. Make minor workpiece alignment adjustments. Item 62520 For technical questions, please call 1-888-866-5797. Page 11 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETY TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the tool. Check for: SETUP • loose hardware • misalignment or binding of moving parts • cracked or broken part 2. AFTER USE, wipe external surfaces of the tool with clean cloth. 3. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. • damaged electrical wiring • any other condition that may affect its safe operation. Belt Inspection and Tensioning 1. Examine V-Belt for cracks, tears in the backing, and other damage. OPERATION 2. Replace V-Belt if damaged, following the instructions under Changing Drill Speed on page 9. MAINTENANCE Page 12 For technical questions, please call 1-888-866-5797. Item 62520 Troubleshooting Tool will not start. 1. Cord not connected. 2. No power at outlet. Tool operates slowly. 3. Tool’s thermal reset breaker tripped (if equipped). 4. Internal damage or wear. (Carbon brushes or switch, for example.) Extension cord too long or wire size too small. Performance 1. Accessory dull or damaged. decreases 2. Carbon brushes worn or damaged. over time. Excessive noise 1. Internal damage or wear. (Carbon or rattling. brushes or bearings, for example.) 2. Belt too loose (slipping) or too tight (bearing damage). Overheating. 1. Forcing machine to work too fast. 2. Accessory dull or damaged. 3. Blocked motor housing vents. 4. Motor being strained by long or small diameter extension cord. Likely Solutions 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Turn off tool and allow to cool. Press reset button on tool. 4. Have technician service tool. SAFETY Possible Causes Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Table A on page 3. 1. Keep cutting accessories sharp. Replace as needed. 2. Have qualified technician replace brushes. 1. Have technician service tool. 2. Properly tension belt. 1. Allow machine to work at its own rate. 2. Keep cutting accessories sharp. Replace as needed. 3. Wear ANSI-approved safety goggles and NIOSH-approved dust mask/respirator while blowing dust out of motor using compressed air. 4. Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Table A on page 3. MAINTENANCE OPERATION Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SETUP Problem Item 62520 For technical questions, please call 1-888-866-5797. Page 13 Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY SAFETY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts List Part SETUP OPERATION MAINTENANCE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Description Base Column Support Flat Washer 8 Spring Washer 8 %ROW0[ Feed Handle Feed Seat Column 6HW6FUHZ0[ Motor Tension Knob Spring Slide Bar Rubber Pad Motor 6HW6FUHZ0[ Motor Pulley %ROW0[ Lock Nut M8 Rubber Pad Nut M5 Rubber Ring Pulley Cover %ROW0[ Flat Washer 5 )ODQJH+HDG6FUHZ0[ Wire Clamp Rubber Ring Knob Wire Clamp Nut M10 Flat Washer 10 Spring Washer 10 Lamp Nut M5 Power Cord Hex Nut 3/8-24 Spring Cap Depth Spring Qty Part Description 1 1 5 3 3 3 1 1 2 1 1 1 1 1 1 1 2 2 4 1 1 1 3 1 4 1 1 1 2 1 2 2 1 1 1 2 1 1 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57A 57B 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Headstock Light Bulb Lock Washer 5 mm 3DQ+HDG6FUHZ0[ Switch Box %ROW0[ Switch Panel 6FUHZ6W[ Power Switch Lamp Switch Nut M8 Set Screw Pivot Lever Table Support Angle Scale Table $QJOH%ROW0[ Pointer Adjustment Nut M10 Lock Nut M10 Stop Rod Washer 6 V-Belt K26 Pulley Nut Spindle Pulley Pulley Insert Ball Bearing 17 mm Spacer Retaining Ring Retaining Ring 11 Ball Bearing 6201 Gasket Spindle Sleeve %ROW0[ Bracket Spindle Chuck Nut M6 Qty 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-888-866-5797. Item 62520 23 29 60 31 33 32 61 28 27 23 SAFETY Assembly Diagram 26 25 24 30 23 62 16 22 63 57B 65 17 36 57A 64 20 36 40 19 37 38 58 41 43 42 44 46 45 64 59 66 21 35 34 3 15 18 39 SETUP 56 13 49 48 50 67 68 69 55 54 53 52 51 70 9 10 11 14 8 7 OPERATION 47 12 6 5 68 4 71 3 72 75 73 2 74 MAINTENANCE 1 Item 62520 For technical questions, please call 1-888-866-5797. Page 15 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797 ">

Public link updated
The public link to your chat has been updated.
Advertisement