Dji | Go | Guide | dji Go User guide

dji Go User guide
Firmware Update Guide
V1.4
INSPIRE 1 Series
PHANTOM 3 Series
Firmware Update Guide
V1.4
PHANTOM 3
STANDARD
Using the DJI GO App to Update All Firmware
Always use the latest version of the DJI GO app to update your
firmware.
Notes:
●
●
●
●
●
●
Ensure your Micro SD card is inserted into the gimbal and has at
least 100 MB of free space. Do not remove the Micro SD card from
the gimbal during the firmware update.
The firmware update process takes around 30 minutes. We
recommend finding a comfortable environment to carry out the
update.
Check, in the DJI GO app, that you have the latest firmware installed
before every flight.
The firmware update requires an internet connection. Connect your
mobile device to a Wi-Fi network whenever possible.
Wait for the progress bar to reach 100% to ensure the firmware
update is complete.
The camera status indicator will blink red and green to show that the
update is in progress.
D
DD
D
The camera status indicator will
become solid green and the
aircraft will sound ‘D
DD’
when the update is complete.
The camera status indicator
will become solid red and the
aircraft will sound ‘D
’ if
the update has failed.
Update Successful
Power off the aircraft.
Updated Failed
Restart the aircraft and try again.
Updating Multiple Intelligent Flight Batteries
Insert the remaining batteries into the aircraft and
power them on to update their firmware.
●
If you failed to update the firmware after multiple
attempts, contact your local dealer or DJI Support:
http://www.dji.com/support
1
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Overview
Using the DJI GO app to update the remote controller *
Page 3
* If your INSPIRE 1 remote controller firmware is below v1.3.00 or
PHANTOM 3 Advanced or Professional remote controller firmware
is below v1.3.20, use a Micro SD card to update the firmware
instead.
●
To check your current firmware version, launch the DJI GO app and
tap through Camera View > System Status Bar > Overall Status.
Using a Micro SD card to update the aircraft and
Intelligent Flight Battery
Pages 4-6
Using a Micro SD card to update older remote
controller firmware below v1.3.00 (Inspire 1) or below
v1.3.20 (Phantom)
Pages 8-9
2
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using the DJI GO app to update the remote
controller
Always use the latest version of the DJI GO app to update your
firmware.
Notes:
●
●
●
●
●
●
●
If you failed to update the firmware after multiple
attempts, contact your local dealer or DJI Support:
http://www.dji.com/support
Only the INSPIRE 1 remote controller firmware v1.3.00 or
PHANTOM 3 Professional or Advanced remote controller firmware
v1.3.20 or later support updating through the DJI GO app. If
necessary, update your remote controller using a Micro SD card.
To check your current firmware version, launch the DJI GO app and
tap through Camera View > System Status Bar > Overall Status.
The firmware update process takes around 10 minutes. We
recommend finding a comfortable environment to carry out the
update.
Check, in the DJI GO app, that you have the latest firmware installed
before every flight.
The firmware update requires an internet connection. Connect your
mobile device to a Wi-Fi network whenever possible.
Wait for the progress bar to reach 100% to ensure the firmware
update is complete.
The remote controller status indicator glows solid blue during the
update.
The remote controller status
indicator becomes solid green
when the update is complete.
The remote controller status
indicator becomes solid red if
the update has failed.
Update Successful
Power off the remote controller.
Updated Failed
Restart the remote controller
and try again.
3
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update the aircraft and
Intelligent Flight Battery
Ensure your Micro SD card has at least 100 MB of free space.
Notes:
●
●
This method does not apply to the Phantom 3 Standard.
If your INSPIRE 1 remote controller firmware is v1.3.00 or above, or
PHANTOM 3 Professional or Advanced remote controller firmware
is v1.3.20 or above, you must use the DJI GO app to update the
firmware.
To check your current firmware version, launch the DJI GO app and
tap through Camera View > System Status Bar > Overall Status.
●
●
The firmware update process takes around 30 minutes. We
recommend finding a comfortable environment to carry out the
update.
Check, in the DJI GO app, that you have the latest firmware installed
before every flight.
4
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update the aircraft and
Intelligent Flight Battery
Ensure your Micro SD card has at least 100 MB of free space.
1
Prepare the Firmware Update Files
Only download the update package from the official DJI website.
INSPIRE 1
www.dji.com/product/inspire-1/download
PHANTOM 3 www.dji.com/product/phantom-3/download
Download the firmware update package.
.bin
Unzip and copy the downloaded files into
the root directory of your Micro SD card.
.bin
Insert your Micro SD card into the SD card
slot on the aircraft.
5
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update the aircraft and
Intelligent Flight Battery
Ensure your Micro SD card has at least 100 MB of free space.
2
Update the Aircraft and Intelligent Flight Battery
Ensure the Intelligent Flight Battery has at least 50% power.
Power on the aircraft to begin the firmware update. Do not power
on the remote controller.
The camera status indicator will blink red and green to show that the
update is in progress.
D
Updating Multiple Intelligent Flight Batteries
DD
D
The camera status indicator will
become solid green and the
aircraft will sound ‘D
DD’
when the update is complete.
The camera status indicator
will become solid red and the
aircraft will sound ‘D
’ if
the update has failed.
Update Successful
Power off the aircraft.
Update Failed
Restart the aircraft and try again.
Insert the remaining batteries into the aircraft and
power them on to update their firmware.
●
●
The Zenmuse X3 on the INSPIRE 1 does not
have a camera status indicator. Use the beeping
sounds to determine the update status.
If you failed to update the firmware after multiple
attempts, contact your local dealer or DJI Support:
http://www.dji.com/support
6
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update older remote
controller firmware
INSPIRE 1 remote controller firmware below v1.3.00
PHANTOM 3 remote controller firmware below v1.3.20
Ensure your Micro SD card has at least 100 MB of free space.
Notes:
●
●
This method does not apply to the Phantom 3 Standard.
If your INSPIRE 1 remote controller firmware is v1.3.00 or above, or
PHANTOM 3 Professional or Advanced remote controller firmware
is v1.3.20 or above, you must use the DJI GO app to update the
firmware.
To check your current firmware version, launch the DJI GO app and
tap through Camera View > System Status Bar > Overall Status.
●
The firmware update process takes around 10 minutes. We
recommend finding a comfortable environment to carry out the
update.
7
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update older remote
controller firmware
INSPIRE 1 remote controller firmware below v1.3.00
PHANTOM 3 remote controller firmware below v1.3.20
Ensure your Micro SD card has at least 100 MB of free space.
1
Prepare the Remote Controller Firmware Update Files
Card reader
or
USB
Flash Drive
If neither a card reader or
USB flash drive is available:
or
.bin
.bin
.bin
Insert your card
reader,
containing your
Micro SD card,
into the rear
USB port.
Insert your USB
flash drive,
containing the
firmware update
files, into the
rear USB port.
Insert the Micro SD card
into the SD card slot on the
aircraft and connect the
Micro USB port on the
camera to the USB port on
the remote controller.
8
Firmware Update Guide
V1.4
INSPIRE 1
PRO
INSPIRE 1
PHANTOM 3
PROFESSIONAL
PHANTOM 3
ADVANCED
Using a Micro SD card to update older remote
controller firmware
INSPIRE 1 remote controller firmware below v1.3.00
PHANTOM 3 remote controller firmware below v1.3.20
Ensure your Micro SD card has at least 100 MB of free space.
2
Update the Remote Controller
Ensure the remote controller has at least 50% power.
Power on the remote controller and wait about a minute for the update
to start.
The remote controller status indicator glows solid blue during the update.
The firmware update process takes around 10 minutes.
●
If you failed to update the firmware after multiple
attempts, contact your local dealer or DJI Support:
http://www.dji.com/support
The remote controller status
indicator becomes solid green
when the update is complete.
The remote controller status
indicator becomes solid red if
the update has failed.
Update Successful
Power off the remote controller.
Updated Failed
Restart the remote controller
and try again.
9
Firmware Update Guide
V1.4
FAQ
10
Q: Can I use the DJI GO app to update the aircraft and Intelligent
Flight Battery firmware for my Phantom 3 Professional or
Advanced?
A: No, this feature is not supported yet.
Q: Why can’t I use the DJI GO app to update the remote controller
firmware?
A: If your remote controller firmware is below v1.3.00 (Inspire 1) or
below v1.3.20 (Phantom), you can only use a Micro SD card or
USB flash drive to update the firmware. You will be able to use the
DJI GO app for your next update.
Q: Why can’t I connect the remote controller to the aircraft?
A: The remote controller may become unlinked from the aircraft after
the firmware update. Refer to the user manual on how to re-link the
remote controller to the aircraft.
Q: Can I receive incoming calls or hide the DJI GO app in the
background during the firmware update?
A: Avoid leaving the app while an update is in progress, or else it may
be disrupted.
Q: How long does it take to update the Intelligent Flight Battery?
A: It takes up to 5 minutes per battery.
Q: How do I know when the firmware update is complete?
A: The camera status indicator will become solid green and the aircraft
will make a ‘D-DD’ sound when the update is complete. Also, the
text ‘result: success’ will appear in the ‘.txt’ file that is automatically
generated in the root directory of your Micro SD card.
This content is subject to change.
If you have any questions about this document,
please contact DJI by sending a message to DocSupport@dji.com.
© 2015 DJI. All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising