ONKYO | TX-NR474 | Owner Manual | ONKYO TX-NR474 User manual

ONKYO TX-NR474 User manual
TX-NR474
AV RECEIVER
Instruction Manual
En
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Table of Contents
Before Start
Before Start ............................................................ 2
What's in the box ..................................................... 3
Part Names ............................................................ 4
Part Names ............................................................. 4
Install ...................................................................... 8
Installation procedure .............................................. 8
Step1: Speaker Layout ............................................ 9
Step2: Connect the Speakers ............................... 14
Step3: Connect the TV & AV Components ............ 15
Initial Setup .......................................................... 20
Initial Setup with Auto Start-up Wizard .................. 20
Playback .............................................................. 22
AV Component Playback ...................................... 22
BLUETOOTH® Playback ...................................... 23
Internet Radio ....................................................... 24
Spotify ................................................................... 26
AirPlay® ................................................................. 27
USB Storage Device ............................................. 28
Listening To the AM/FM Radio .............................. 29
Music Server ......................................................... 32
Supplementary information for player functions .... 34
Listening Mode ...................................................... 35
Advanced Setup .................................................. 52
Setup Menu ........................................................... 52
Quick Menu ........................................................... 66
Web Setup ............................................................ 68
Firmware Update .................................................. 69
Supplementary Information ............................... 72
Supplementary Information ................................... 72
Others .................................................................. 73
Troubleshooting .................................................... 73
General Specifications .......................................... 78
Reference Information .......................................... 80
2
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
What's in the box
1. Main unit (1)
2. Remote controller (RC-956R) (1), batteries (AAA/R03)
(2)
3. Speaker setup microphone (1)
0 Used during Initial Setup.
4. Indoor FM antenna (1)
5. AM loop antenna (1)
1
0 Quick Start Guide (1)
* This document is an online instruction manual. It is not
included as an accessory.
2
3
4
5
0 Connect speakers with 4 ≠ to 16 ≠ impedance.
0 The power cord must be connected only after all other
cable connections are completed.
0 We will not accept responsibility for damage arising from
the connection of equipment manufactured by other
companies.
0 Functionality may be introduced by firmware updates
and service providers may cease services, meaning that
some network services and content may become
unavailable in the future. Furthermore, available services
may vary depending on your area of residence.
0 Details on the firmware update will be posted on our
website and through other means at a later date.
0 Specifications and appearance are subject to change
without prior notice.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this product. Refer
to our website for more information.
En
3
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Part Names
Part Names





 

Front Panel
1. Í ON/STANDBY button
2. PURE AUDIO button/indicator: Switches the unit to Pure Audio mode (P38).
3. HYBRID STANDBY indicator: Lights if the unit enters standby mode when the features
are enabled that continue to work when this unit is in standby, such as HDMI Standby
Through and Network Standby.
4. Remote control sensor: Receives signals from the remote controller.
0 The signal range of the remote controller is within about 16y/5 m, at an angle of 20° on
the perpendicular axis and 30° to either side.
5. TUNING MODE button: Switches tuning to an AM/FM station between automatic tuning
and manual tuning.
6. DIMMER button: You can adjust the brightness of the display in three steps. It cannot be
turned off completely.
4

  



 
7. Display(P5)
8. SETUP button: You can show advanced setting items on the TV and display to provide
you with an even better experience (P52).
9. Cursors (S / T / W / X), ENTER button: Select the item with the cursors and press
ENTER to confirm. Use them to tune to stations when using TUNER (P29).
10.RETURN button: Returns the display to the previous state during setting.
11. MASTER VOLUME
12.PHONES jack: Connect stereo headphones with a standard plug (Ø 1/4z/6.3 mm
diameter).
13.TONE and Tone Level buttons: You can adjust the sound quality of the front speakers.
Press TONE to select the desired setting from "Bass" and "Treble", and adjust with the
Tone Level buttons (-/+).
14.MEMORY button: Used to register AM/FM radio stations.
15.Input selector buttons: Switches the input to be played.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
16.LISTENING MODE buttons: Select listening modes
(P35).
17.SETUP MIC jacks: Connect the supplied speaker
setup microphone.
18.AUX INPUT jacks:
Connect a video camera, etc., using a stereo mini plug
cable (Ø 1/8z/3.5 mm).








Display
1. Speaker/Channel display: Displays the output channel that
corresponds to the selected listening mode.
2. Lights in the following conditions.
Ë: When headphones are connected
: When connected via BLUETOOTH
: When connected by Wi-Fi
NET: When "NET" is selected with the input selector and the unit is
connected to the network. It will flash if the connection to the network is
not correct.
USB: When "NET" is selected with the input selector and the unit is
connected by USB and the USB device is selected. Flashes if the USB
is not properly connected.
HDMI: HDMI signals are input and the HDMI input selector is selected.
DIGITAL: Digital signals are input and the digital input selector is
selected.
3. Lights according to the type of input digital audio signals and the
listening mode.
4. Lights in the following conditions.
RDS: Receiving RDS broadcasting.
TUNED: Receiving AM/FM radio.
FM ST: Receiving FM stereo.
SLEEP: Sleep timer has been set.
AUTO STBY: Auto Standby has been set.
5. Flashes when muting is on.
6. Displays various information of the input signals.
7. This may light when performing operations with the "NET" input
selector.
En
5
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others








90°

180°



Rear Panel
1. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV component digital audio signals
with a digital optical cable or digital coaxial cable.
2. VIDEO IN jacks: Input the video signals of an AV component with an analog video cable.
3. ETHERNET jack: Connect to the network with an Ethernet cable.
4. USB jack: A USB storage device is connected so that music files stored in it can be
played. You can also supply power (5 V/1 A) to USB devices with a USB cable.
5. Wireless antenna: Raise for Wi-Fi connection or when using a BLUETOOTH wireless
technology enabled device. Adjust their angles according to the connection status.
6. HDMI OUT jack: Connect a HDMI cable to transfer video signals and audio signals to a
TV.
7. HDMI IN jacks: Input video signals and audio signals with a HDMI cable connected to an
AV component.
6

8. Power cord
9. AUDIO IN jacks: Input AV component audio signals with an analog audio cable.
10.TUNER AM/FM 75≠ jacks: Connect the supplied antenna.
11. SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a subwoofer cable.
12.SPEAKERS jacks: Connect speakers with speaker cables.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Remote Controller


1. Í ON/STANDBY button
2. Input selector buttons: Switches the input to be played.
3. Q (QUICK MENU) button: Settings such as "Tone" and
"Level" can be made quickly during play on the TV screen
(P66).
4. Cursors, ENTER button: Select the item with the cursors and
press ENTER to confirm. When the folder or file lists are not
shown on one screen on the TV, press W/X to change the
screen.
5.
button: You can show advanced setting items on the TV
and display to provide you with an even better experience
(P52).
6. Volume buttons
7.
button: Temporarily mutes audio. Press again to cancel
muting.
8. LISTENING MODE buttons: Select listening modes (P35).
9. Play button: Used for play operations when playing Music
Server or USB.
10.
button: Used for repeat or random play operations
when playing Music Server or USB. Each time you press the
button, the mode switches from
(1-track repeat), to
(folder repeat), to
(random).
CLEAR button: Deletes all characters you have entered
when entering text on the TV screen.
11. DIMMER button: You can adjust the brightness of the display
in three steps. It cannot be turned off completely.
12. button: Switches the information on the display and is
used to operate RDS (P30).
13. button: Returns the display to the previous state during
setting.
14.MODE button: Switches tuning to an AM/FM station between
automatic tuning and manual tuning.
15.MEMORY button: Used to register AM/FM radio stations.

0 MAIN and ZONE buttons are not used.












En
7
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Installation procedure
Install
This unit can be used in a number of ways, depending on
the layout of the speakers you are installing, and the
connections made to external devices. Read the following
to help make the installation process smoother.
1
Step1: Speaker Layout
Select the speaker layout that suits the types of speakers
you have and the conditions they will be used in from the
choices presented on pages P9 to P12, then install the
speakers by referring to the illustrations and explanations
on the relevant page. Speaker layouts include systems that
use surround speakers and systems that use height
speakers. Also refer to the combinations available in
"Speaker combinations" on P13.
Step2: Connect the Speakers
2
3
Connect the speaker system to this unit. The connection
process will be smoother if you refer to the illustrations and
explanations and prepare the required cables before hand.
Step3: Connect the TV & AV Components
Refer to P15 to P19 to connect your external devices such
as your TV, Blu-Ray Disc Player, and also supplied
accessories such as the antennas. The connection process
will be smoother if you refer to the illustrations and
explanations, confirm the connection types on the external
devices, and prepare the required cables before hand.
8
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Step1: Speaker Layout
5.1 Channel System
Front speakers output front stereo sound and the center
speaker outputs sounds emanating from the center of the
screen, such as dialog and vocals. Surround speakers
create the sound field at the rear. The powered subwoofer
reproduces bass sounds and enriches the sound field. The
optimal positioning for front speakers is at ear height, and
for surround speakers it is just above ear height. The center
speaker should be set up at an angle to face the listening
position. Placing the powered subwoofer between the
center speaker and a front speaker gives you a natural
sound even when playing music.
*1
*2
1,2
3
4,5
6
Front Speakers
Center Speaker
Surround Speakers
Powered Subwoofer
¢1: 22° to 30°, ¢2: 120°
En
9
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
3.1.2 Channel System-1
(Front High Speakers)
3´ (0.9 m)
or more
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of front high speakers, a type of height speaker. Front high
speakers should be situated at least 3y/0.9 m higher than
the front speakers. They should also be put directly above
the front speakers, angled to face the listening position.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes
the most up-to-date 3D sound including overhead
sounds, when the input format is Dolby Atmos. Visit our
website for details about firmware updates.
1,2
3
4,5
6
¢1: 22e to 30e
10
Front Speakers
Center Speaker
Front High Speakers
Powered Subwoofer
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
3.1.2 Channel System-2
(Ceiling Speakers)
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of top middle speakers, a type of height speaker. Fit top
middle speakers on the ceiling directly above the listening
position. The distance between each pair should match the
distance between the two front speakers.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes
the most up-to-date 3D sound including overhead
sounds, when the input format is Dolby Atmos. Visit our
website for details about firmware updates.
0 Dolby Laboratories recommends placing this type of
height speakers to obtain the best Dolby Atmos effect.
1,2
3
4,5
6
Front Speakers
Center Speaker
Top Middle Speakers
Powered Subwoofer
¢1: 65° to 100°
En 11
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
3.1.2 Channel System-3
(Dolby Enabled Speakers (Dolby Speakers))
*1
This is a 3.1-channel system consisting of front speakers, a
center speaker, and a powered subwoofer, with the addition
of Dolby enabled speakers (front), a type of height speaker.
Dolby enabled speakers are special speakers designed to
face the ceiling so that sound is heard after bouncing off the
ceiling so that sound appears to be coming from overhead.
Place Dolby enabled speakers (front) above the front
speakers.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. After this
firmware update, by installing height speakers, you can
select the Dolby Atmos listening mode, which realizes
the most up-to-date 3D sound including overhead
sounds, when the input format is Dolby Atmos. Visit our
website for details about firmware updates.
1,2
3
4,5
6
¢1: 22° to 30°
12
Front Speakers
Center Speaker
Dolby Enabled Speakers (Front)
Powered Subwoofer
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Speaker combinations
Speaker Channels
FRONT
CENTER
SURROUND
HEIGHT
2.1 ch
3.1 ch
4.1 ch
5.1 ch
2.1.2 ch
3.1.2 ch
En 13
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Step2: Connect the Speakers
Make correct connection between the unit's jacks and
speaker's jacks (+ to + and - to -) for each channel. If
connection is wrong, reverse phase may make bass output
poor.
1/2˝
(12 mm)
b
a
Setup
0 Settings for the speaker configuration you have
connected need to be made in "1. AccuEQ Room
Calibration" in Initial Setup (P20).
0 If any of the connected speakers have an
impedance of 4 ≠ or more to less than 6 ≠, after
completing Initial Setup, you need to make some
settings in the Setup menu. Press
on the
remote controller, select "2. Speaker" "Configuration" and set "Speaker Impedance" to
"4ohms".
Connect the speaker cable so the wires do not protrude from the
speaker jacks.
If the exposed wires of the speakers touch the rear panel or the +
and - wires touch each other, the protection circuit will be
activated.
a Speaker cable, b Subwoofer cable
14
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Step3: Connect the TV & AV Components
1. Connect the TV
To ARC TV
For a TV that supports the ARC (Audio Return Channel)
feature, use an HDMI cable and connect according to
illustration "a". Choose an HDMI IN jack on the TV that
supports ARC when connecting.
Setup
0 Settings are required to use the ARC function.
For "4. Audio Return Channel" (P21) in Initial
Setup, select "Yes".
0 Refer to the instruction manual for the TV for TV
connections and instructions regarding settings
for CEC features and audio output.
To Non-ARC TV
For a TV that does not support the ARC (Audio Return
Channel) feature (*), connect both the HDMI cable in
illustration "a" and the digital optical cable in "b".
0 Connection with a digital optical cable is not necessary if
you will watch TV through a device such as a cable settop box (that is, not use a tuner built into the TV) that you
have connected to the input jack on this unit.
a
(*) The ARC feature: This feature transfers TV audio signals via
HDMI cable so that you can play the audio from the TV through
this unit. Connection to an ARC compatible TV is complete with
one HDMI cable. Refer to the instruction manual for your TV to
see if it supports ARC.
b
TV
a HDMI cable, b Digital optical cable
En 15
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
2. Connect the HDMI AV Component
This is an example of connection with an AV component
that has an HDMI jack. With connection to an AV
component that conforms with the CEC (Consumer
Electronics Control) standard, you can use features such as
the HDMI CEC feature (*) that links with the input selector,
and the HDMI Standby Through feature which allows you to
play video and audio from AV components on the TV even
when this unit is in standby mode.
0 To play 4K or 1080p video, use the high speed HDMI
cable.
Setup
0 When "Yes" is selected for "4. Audio Return
Channel" in Initial Setup (P21), the HDMI CEC
function and HDMI Standby Through function are
automatically enabled. If "No, Skip" is selected,
settings are required in the Setup menu after
Initial Setup is complete. Press
on the remote
controller and make the settings in "5. Hardware"
- "HDMI".
0 To enjoy digital surround sound including Dolby
Digital, audio output should be set to "Bitstream
output" on the connected Blu-ray Disc player or
other device.
a
(*) The HDMI CEC feature: You can control features such as linking
input switching with the input selector and players conforming to
the CEC standard, switching audio to output it from the TV or
from this unit, and adjusting the volume using the remote
controller of a CEC-compliant TV, and automatically switching
this unit to standby when the TV is turned off.
BD/DVD
Cable/Satellite set-top
box
a HDMI cable
16
Streaming media
player
GAME
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
3. Connect the Non-HDMI AV Component
This is an example of connection with an AV component
that does not have an HDMI jack. Select the cables to make
the connections to the AV component to match the jacks it
has. When video input connection is to the CBL/SAT jack,
the audio input connection should also be to the CBL/SAT
jacks, and so on, so that you connect the video input jacks
to the jacks with the same name as the audio input jacks.
Note that video signals input to the VIDEO IN jack will be
converted to HDMI video signals and then output from the
HDMI OUT output jack.
0 To enjoy digital surround playback, such as Dolby Digital,
the audio signals need to pass through a connection via
digital coaxial cable or digital optical cable.
0 It is possible to change assignment of the input jacks you
see in the illustration at left, so you can also connect to
any jack other than CBL/SAT (P53, 54).
Setup
0 To enjoy digital surround sound including Dolby
Digital, audio output should be set to "Bitstream
output" on the connected Cable/Satellite set-top
box or other device.
a
b
Cable/Satellite set-top
box
a Analog video cable, b Digital coaxial cable
En 17
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
4. Connect the Audio Component
Example of a connection with an Audio component.
Connect a CD player using a digital optical cable or analog
audio cable.
a
OR
b
CD
a Digital optical cable, b Analog audio cable
18
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
5. Connect Other Cables
Antenna Hookup
Move the antenna around while playing the radio to find the
position with the best reception. Use a thumb tack or similar
to attach the FM indoor antenna to a wall.
b
2
Network Hookup
a
d
Connect this unit to the network using wired LAN or Wi-Fi
(wireless LAN). You can enjoy Network Functions such as
internet radio by connecting to the network. If you connect
by wired LAN, connect to the router with an Ethernet cable
to the ETHERNET port as shown in the illustration. To
connect by Wi-Fi, after selecting "Wireless" in "3. Network
Connection" (P21) in Initial Setup, select the desired setting
method and follow the onscreen instructions to configure
the connection.
Power Cord Hookup
The power cord must be connected only after all other
connections are completed.
c
a FM indoor antenna, b AM indoor antenna, c Ethernet cable, d Power cord
En 19
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Initial Setup with Auto Start-up Wizard
Initial Setup
Initial Setup starts automatically
1
INPUT
TV
When you turn the unit on for the first time after purchasing
it, Initial Setup is automatically shown on the TV to enable
you to make settings required for startup using simple
operations following onscreen guidance.
1. Switch the input on the TV to that assigned to the unit.
2. Put batteries into the remote controller of this unit.
3. Press Í on the remote controller to turn the unit on.
4. Select the item with the cursors of the remote controller
and press ENTER (a) to confirm your selection. To return
to the previous screen, press
(b).
a
2
3
b
0 If you terminate the procedure on the way or want to
change a setting made during Initial Setup, press
on
the remote controller, and select "6. Miscellaneous" "Initial Setup" and press ENTER. To select the language
displayed again, change "OSD Language" (P52).
∫ 1. AccuEQ Room Calibration
Place the supplied speaker setup microphone in the
listening position, measure the test tones emitted by the
speakers, then the unit automatically sets the optimum
volume level for each speaker, the crossover frequencies,
and the distance from the listening position. This also
automatically adjusts the equalizers for the speakers and
enables correction of distortion caused by the acoustic
environment of the room.
20
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
0 Calibration takes between 3 and 12 minutes to be
completed. The speakers emit the test tone at high
volume during measurement, so be careful of your
surroundings. Also, keep the room as quiet as possible
during measurement.
0 If you have connected a subwoofer, check the power and
volume of the subwoofer. Set the subwoofer volume to
more than halfway.
0 If the power of this unit suddenly turns off, the wires in
the speaker cables may have touched the rear panel or
other wires and tripped the protection circuit. Twist the
wires again properly and make sure they do not stick out
of the speaker terminals when connecting.
1. Place the supplied speaker setup microphone in the
listening position, and connect to the SETUP MIC jack on
the main unit.
SETUP MIC
When putting the speaker setup microphone on a tripod,
refer to the illustration when putting it in place.
2. Select the connected speaker configuration.
∫ 3. Network Connection
AccuEQ Room Calibration
Speaker Channels 5.1 ch < >
Subwoofer
Height Speaker
Yes
---
Select how many speakers you have.
Next
The image on the screen changes as you choose the
number of channels in "Speaker Channels", so refer to it
when performing the settings.
3. Test tones are emitted by the speakers, and firstly the
unit detects the speakers connected and the noise in the
environment.
4. After the results of the measurements in step 3 above
are displayed, select "Next", press ENTER on the remote
controller, and the test tones are emitted again, and the
unit automatically makes settings such as the optimum
volume level and the crossover frequency.
5. When the measurement is completed, the measurement
result is displayed. Press the cursors W / X on the
remote controller to check the settings. Select "Save"
and press ENTER to save the settings.
6. Select whether to enable or disable the equalizer
function that corrects for distortion caused by the
acoustic environment of the room.
If this is to be enabled, then normally you should select
"On (All Channels)", and to disable just the front
speakers you should select "On (Except Front Left /
Right)".
7. Disconnect the speaker setup microphone.
∫ 2. Source Connection
Check that each input source is connected correctly. Follow
the guidance, select the input you want to confirm, start
play of the selected player, and confirm that the images
appear on the TV and that sound is played.
Set up Wi-Fi connection with an access point such as a
wireless LAN router. There are the following two methods of
connecting by Wi-Fi:
"Scan Networks": Search for an access point from this
unit. Find out the SSID of the access point beforehand.
"Use iOS Device (iOS7 or later)": Connect by sharing the
iOS device's Wi-Fi settings with this unit.
If you select "Scan Networks", there are a further two
choices of connection method. Check the following.
"Enter Password": Enter the password (or key) of the
access point to connect.
"Push Button": If the access point has an automatic
connection button, you can connect without entering a
password.
0 If the SSID of the access point is not displayed, then in
the screen listing the SSIDs, select "Other..." with the X
cursor on the remote controller and press ENTER, then
follow the onscreen instructions.
Keyboard input
To switch between upper and lower case, select "A/a" on
the screen and press ENTER. To select whether to mask
the password with "¢" or display it in plain text, press
MEMORY on the remote control. Pressing CLEAR will
delete all the input characters.
0 A confirmation screen asking you to agree to the privacy
policy is displayed during network setting. Select
"Accept" and press ENTER to indicate agreement.
∫ 4. Audio Return Channel
If you have connected a TV that supports ARC, select
"Yes". This unit's ARC setting turns on and you can listen to
the TV's audio through this unit.
En 21
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
AV Component Playback
Playback
2
1
INPUT
TV
Basic operations
3. Start play on the AV component.
You can play the audio from AV
components such as Blu-ray Disc players
through this unit.
Perform the following procedure when the
unit is on.
1. Switch the input on the TV to that
assigned to the unit.
2. Press the input selector (a) on the
remote controller with the same name as
the jack to which you connected the
player to switch the input.
For example, press the BD/DVD button
to play the player connected to the BD/
DVD jack. Press TV to listen the TV's
sound. To play a device connected to the
AUX INPUT jack on the front panel,
press AUX.
0 When the CEC link function works,
the input switches automatically when
you have connected a CEC compliant
TV and player to this unit using HDMI
connection.
22
a
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
BLUETOOTH® Playback
1
2
3
Onkyo TX-NR474 XXX
You can wirelessly play music on a
smartphone or other BLUETOOTH
wireless technology enabled device.
Perform the following procedure when the
unit is on.
Pairing
1. When you press the
button, "Now
Pairing..." is displayed on this unit's
display, and the pairing mode is enabled.
2. Enable (turn on) the BLUETOOTH
function of the BLUETOOTH wireless
technology enabled device, then select
this unit from amongst the devices
displayed. If a password is requested,
enter "0000".
0 This unit is displayed as "Onkyo TXNR474 XXXXXX".
0 To connect another BLUETOOTH
wireless technology enabled device,
press and hold
until "Now
Pairing..." is displayed, then perform
step 2. This unit can store the data of
up to eight paired devices.
0 The coverage area is 48y/15 meters.
Note that connection is not always
guaranteed with all BLUETOOTH
wireless technology enabled devices.
Playing Back
1. Perform the connection procedure on
the BLUETOOTH wireless technology
enabled device.
The input on this unit automatically
switches to "BLUETOOTH".
2. Play the music files. Increase the volume
of the BLUETOOTH wireless technology
enabled device to an appropriate level.
0 Due to the characteristics of
BLUETOOTH wireless technology, the
sound produced on this unit may slightly
be behind the sound played on the
BLUETOOTH wireless technology
enabled device.
En 23
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Internet Radio
1
2
3
INPUT
TV
You can use internet radio services such as
TuneIn Radio, Pandora, Deezer, and
TIDAL by connecting this unit to a network
that has an internet connection.
0 The network needs to be connected to
the internet in order to play internet radio
services.
0 Depending on the internet radio service,
the user may need to register from their
computer first. Refer to the websites for
each of the services for details about
them.
0 Functionality may be introduced by
firmware updates and service providers
may cease services, meaning that some
network services and content may
become unavailable in the future.
24
to display a list of Network Functions on
the TV.
3. Select the internet radio service you
want with the cursors of the remote
controller and press ENTER (b) to
confirm your selection.
4. Follow the on-screen instructions, using
the cursors to select radio stations and
programs, then press ENTER to play.
Play starts when 100% is displayed for
buffering.
0 To return to the previous screen, press
(c).
Internet radio service menus
a
b
c
You can register certain stations as your
favorites or delete stations you have
registered from your favorites. The menu
displayed depends on the service currently
selected.
Menu icons
are displayed at the
bottom right of the screen while playing a
station. When just this icon is displayed,
you can display the menu on the screen
just by pressing ENTER on the remote
controller. When multiple icons are
displayed, select an
icon with the
cursors of the remote controller and press
ENTER.
Playing Back
Regarding the TuneIn Radio
Account
Perform the following procedure when the
unit is on.
1. Switch the input on the TV to that
assigned to the unit.
2. Press NET (a) on the remote controller
Creating an account on the TuneIn Radio
website (tunein.com) and logging in it from
the unit allows you to automatically add
your favorite radio stations and programs
to your "My Presets" on the unit as you
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
follow them on the website. "My Presets"
are displayed in the level under TuneIn
Radio.
To display a radio station registered in "My
Presets", you must log into TuneIn Radio
from the unit. To log in, select "Login" - "I
have a TuneIn account" in the "TuneIn
Radio" top list on the unit, and then enter
your user name and password.
0 If you select "Login" on this unit, you can
use the displayed registration code to
associate this device on the My Page
section of the TuneIn Radio website so
that you can login to "Login" - "Login with
a registration code" without having to
enter your user name and password.
En 25
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Spotify
1
2
3
4
Wi-Fi
Device
Devices Available
Spotify Connect play is possible by
connecting this unit to the same network as
a smart phone or tablet.
0 To play Spotify Connect, you need to
install the Spotify application on your
smartphone or tablet. You also need to
create a Spotify premium account.
– Refer to the following for Spotify
settings: www.spotify.com/connect/
Playing Back
1. Connect the smartphone to the access
point that this unit is connected to.
2. Start the Spotify app.
3. Play the track in the Spotify app, then
after switching to the screen for
controlling play, tap "Devices Available"
at the bottom of the screen.
4. Select this unit.
5. This unit turns on automatically and the
input selector changes to NET and
streaming of Spotify starts.
0 If "5. Hardware" - "Power Management"
- "Network Standby" is set to "Off" in the
26
Setup menu, manually turn the unit on
and then press NET on the remote
controller.
Onkyo TX-NR474 XXX
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
AirPlay®
1
2
Wi-Fi
3
2
4
iPhone
Onkyo TX-NR474 XXXXXX
e.g., iOS 10
Basic operations
You can wirelessly enjoy the music files on
an iPhone®, iPod touch®, or iPad®
connected to the same access point as this
unit.
0 Update the OS version on your iOS
device to the latest version.
0 There may be some differences in the
operations screens and how operations
are performed on the iOS device
depending on the iOS version. For
details, see the operating instructions for
the iOS device.
1. Connect the iOS device to the access
point.
2. Press NET.
3. Tap the AirPlay icon
in the play
screen of the music app on the iOS
device and select this unit from the list of
devices displayed.
4. Play the music files on the iOS device.
0 The default status is for the Network
Standby feature to be on, so when you
do steps 3 and 4 above, this unit
automatically comes on and input
switches to "NET". To reduce the
amount of power consumed in standby
mode, press the
button on the remote
controller, then in the Setup menu
displayed set "5. Hardware" -"Power
Management" -"Network Standby" to
"Off".
0 Due to the characteristics of AirPlay
wireless technology, the sound produced
on this unit may slightly be behind the
sound played on the AirPlay-enabled
device.
You can also play the music files on a
computer with iTunes (Ver. 10.2 or later).
Before operation, make sure this unit and
the PC are connected to the same network,
then press NET on this unit. Next, click the
AirPlay icon
in iTunes, select this unit
from the list of devices displayed, and start
play of a music file.
En 27
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
USB Storage Device
1
2
3
4
INPUT
TV
Basic operations
You can play music files stored on a USB
storage device.
Perform the following procedure when the
unit is on.
1. Switch the input on the TV to that
assigned to the unit.
2. Plug your USB storage device with the
music files into the USB port of this unit’s
rear panel.
3. Press NET (a) on the remote controller
to display the network service list
screen.
4. With the cursors on the remote
controller, select "USB", and then press
ENTER (b).
0 If the "USB" indicator flashes on the
display, check whether the USB
storage device is plugged in properly.
0 Do not unplug the USB storage
device while "Connecting···" is on the
display. This may cause data
corruption or malfunction.
28
5. Press ENTER on the remote controller
again in the next screen. The list of
folders and music files on the USB
storage device are displayed. Select the
folder with the cursors and press ENTER
to confirm your selection.
6. With the cursors on the remote
controller, select the music file, and then
press ENTER to start playback.
0 To return to the previous screen, press
(c).
0 The USB port of this unit conforms with
the USB 2.0 standard. The transfer
speed may be insufficient for some
content you play, which may cause
some interruption in sound.
0 Note that operation is not guaranteed
with all USB storage devices.
0 This unit can use USB storage devices
that comply with the USB mass storage
device class standard. The unit is also
compatible with USB storage devices
using the FAT16 or FAT32 file system
formats.
a
b
c
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Listening To the AM/FM Radio
1
You can receive FM and AM radio stations
on this unit with the built-in tuner. Perform
the following procedure when the unit is on.
∫ Tuning into a Radio Station
Tuning Automatically
1. Repeatedly press TUNER (a) on the
remote controller and select "AM" or
"FM".
2. Press MODE (e) on the remote
controller so that "TunMode:Auto"
appears on the display.
3. When you press the cursor S/T buttons
(b) on the remote controller, automatic
tuning starts, and searching stops when
a station is found. When tuned into a
radio station, the "TUNED" indicator on
the display lights. When tuned into an
FM radio station, the "FM ST" indicator
2
lights.
When FM broadcasts reception is poor:
Perform the procedure for "Tuning
Manually" in the following section. Note
that if you tune manually, the reception for
FM broadcasts will be monaural rather than
stereo, irrespective of the sensitivity of the
reception.
Tuning Manually
If you tune manually, the reception for FM
broadcasts will be monaural rather than
stereo, irrespective of the sensitivity of the
reception.
1. Repeatedly press TUNER (a) on the
remote controller and select "AM" or
"FM".
2. Press MODE (e) on the remote
controller so that "TunMode:Manual"
appears on the display.
3
3. While pressing the cursor S/T buttons
(b) on the remote controller, select the
desired radio station.
0 The frequency changes by 1 step
each time you press S/T. The
frequency changes continuously if the
button is held down and stops when
the button is released.
a
b
Frequency step setting
Press
on the remote controller, then use
the cursor buttons and ENTER on the
remote controller to select "6.
Miscellaneous" - "Tuner" - "AM Frequency
Step", and select the frequency step for
your region. Note that when this setting is
changed, all radio presets are deleted.
c
d
e
En 29
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
1
2
∫ Registering a station
You can register up to 40 of your favorite
AM/FM radio stations.
Registering
After tuning into the AM/FM radio station
you want to register, perform the following
procedure.
1. Press MEMORY (d) on the remote
controller so that the preset number on
the display flashes.
2. While the preset number is flashing
(about 8 seconds), repeatedly press the
cursor W/X buttons (b) on the remote
controller to select a number between 1
and 40.
3. Press MEMORY on the remote
controller again to register the station.
When the station is registered, the
30
3
preset number stops flashing. Repeat
this procedure for all of your favorite AM/
FM radio stations.
Selecting a Preset Radio Station
1. Press TUNER (a) on the remote
controller.
2. Press the cursor W/X buttons (b) on the
remote controller to select a preset
number.
Deleting a Preset Radio Station
1. Press TUNER (a) on the remote
controller.
2. Press the cursor W/X buttons (b) on the
remote controller to select the preset
number to delete.
3. After pressing MEMORY (d) on the
remote controller, press CLEAR (c) while
the preset number is flashing to delete
the preset number. When deleted, the
number on the display goes off.
∫ Using RDS
RDS stands for Radio Data System and is
a method of transmitting data in FM radio
signals. In regions using RDS, the radio
station name is displayed when you tune
into a radio station broadcasting program
information. Further, when you press
on
the remote controller in this state, you can
use the following functions.
Displaying text information (Radio
Text)
1. While the name of the station is being
displayed on the display, press
on the
remote controller once.
Text information broadcast by the station
(Radio Text) is displayed scrolling across
the display. "No Text Data" is displayed
when no text information is available.
Search for stations by Program
Type
1. While the name of the station is being
displayed on the display, press
on the
remote controller twice.
2. Press the cursors W/X on the remote
controller to select the Program Type
you want to find, then press ENTER to
start the search.
0 The Program Types displayed are as
follows: None / News (News reports) /
Affairs (Current affairs) / Info
(Information) / Sport / Educate
(Education) / Drama / Culture /
Science (Science and technology) /
Varied / Pop M (Pop music) / Rock M
(Rock music) / Easy M (Middle of the
road music) / Light M (Light classics) /
Classics (Serious classics) / Other M
(Other music) / Weather / Finance /
Children (Children’s programmes) /
Social (Social affairs) / Religion /
Phone In / Travel / Leisure / Jazz
(Jazz music) / Country (Country
music) / Nation M (National music) /
Oldies (Oldies music) / Folk M (Folk
music) / Document (Documentary)
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
0 The information displayed may
sometimes not match the content
being broadcast by the station.
3. When a station is found, the station
flashes on the display. Press ENTER
while this is happening to start receiving
that station. If you don't press ENTER,
the unit continues to search for another
station.
0 If no stations are found, the message
"Not Found" is displayed.
0 Unusual characters may be displayed
when the unit receives unsupported
characters. However, this is not a
malfunction. Also, if the signal from a
station is weak, information may not be
displayed.
En 31
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Music Server
1
2
3
INPUT
TV
It is possible to stream music files stored
on PCs or NAS devices connected to the
same network as this unit.
0 The network servers compatible with the
Music Server feature are those PCs with
players installed that have the server
functionality of Windows Media® Player
11 or 12, or NAS that are compatible
with home network functionality. Note
that with PCs, only music files registered
in the library of Windows Media® Player
can be played.
0 You may need to make some settings on
the PC in advance to use Windows
Media® Player 11 or 12 with the Music
Server feature.
∫ Windows Media® Player
settings
On Windows
Media®
Player 11
1. Turn on your PC and start Windows
Media® Player 11.
2. In the "Library" menu, select "Media
Sharing" to display a dialog box.
3. Select the "Share my media" check box,
and then click "OK" to display the
compatible devices.
4. Select this unit, click "Allow" and put a
check mark next to the icon for this unit.
5. Click "OK" to close the dialog.
0 Depending of the version of Windows
Media® Player, there may be differences
in the names of items you can select.
On Windows Media® Player 12
1. Turn on your PC and start Windows
Media® Player 12.
2. In the "Stream" menu, select "Turn on
media streaming" to display a dialog
box.
32
0 If media streaming is already turned on,
select "More streaming options..." in the
"Stream" menu to list players in the
network, and then go to step 4.
3. Click "Turn on media streaming" to list
players in the network.
4. Select this unit in "Media streaming
options" and check that it is set to
"Allow".
5. Click "OK" to close the dialog.
0 Depending of the version of Windows
Media® Player, there may be differences
in the names of items you can select.
∫ Playing Back
Before performing the operations below,
start the server (Windows Media® Player
11, Windows Media® Player 12, or NAS
device) containing the music files to play,
and make sure that the PCs and/or NASs
are properly connected to the same
network as this unit.
Perform the following procedure when the
unit is on.
1. Switch the input on the TV to that
assigned to the unit.
2. Press NET (a) on the remote controller
to display a list of Network Functions on
the TV.
3. Select "Music Server" with the cursors of
the remote controller and press ENTER
(b) to confirm your selection.
4. Select the target server with the cursors
on the remote controller and press
ENTER to display the items list screen.
5. With the cursors on the remote
controller, select the music file to play,
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
and then press ENTER to start playback.
0 To return to the previous screen, press
(c).
0 If "No Item." is displayed, check whether
the network is properly connected.
0 Depending on the server and share
settings, the unit may not recognize it, or
may not be able to play its music files.
Furthermore, the unit cannot access
pictures and videos stored on servers.
0 For music files on a server, there can be
up to 20,000 tracks per folder, and
folders may be nested up to 16 levels
deep.
a
b
c
∫ Controlling Remote Playback
from a PC
You can use this unit to play music files
stored on your PC by operating the PC
inside your home network. The unit
supports remote playback with Windows
Media® Player 12.
1. Turn on your PC and start Windows
Media® Player 12.
2. Open the "Stream" menu and check that
"Allow remote control of my Player..." is
checked. Click "Turn on media
streaming" to list players in the network.
3. Switch the input on the TV to that
assigned to the unit.
4. Select and right-click the music file to
play with Windows Media® Player 12. To
remotely play a music file on another
server, open the target server from
"Other Libraries" and select the music
file to play.
5. Select this unit in "Play to" to open the
"Play to" window of Windows Media®
Player 12 and start playback on the unit.
If your PC is running on Windows® 8.1,
click "Play to", and then select this unit. If
your PC is running on Windows® 10,
click "Cast to Device", and select this
unit. Operations during remote playback
are possible from the "Play to" window
on the PC. The playback screen is
displayed on the TV connected to the
HDMI output of the unit.
6. Adjust the volume using the volume bar
on the "Play to" window.
0 Sometimes, the volume displayed on the
remote playback window may differ from
that appeared on the display of the unit.
Also, when the volume is adjusted from
this unit, this is not reflected in the "Play
to" window.
0 Remote playback is not possible when
using a network service or playing music
files on a USB storage device.
0 Depending of the version of Windows®,
there may be differences in the names of
items you can select.
En 33
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Supplementary information for player functions
Due to firmware (the software for the system) updates after
you make your purchase or firmware changes during
production of the product, there may be additions or
changes to the features available compared to what is in
the instruction manual.
For information about player functions that have been
added or changed, see the following references. Refer to
"Supplementary Information" (P72) for information about
changes to settings, etc., other than player functions.
Supplementary information for player functions
>>> Click here <<<
34
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Listening Mode
Selecting Listening Modes
Checking the input format and listening mode
This unit is equipped with a variety of listening modes, and
you can select the optimum listening mode for movies, TV,
music, and games using the MOVIE/TV, MUSIC, and
GAME buttons (b).
1. During play, press one of the three buttons (b) on the
remote controller.
2. Press the selected button repeatedly to switch the
modes displayed on the display of the unit.
Press
(a) on the remote controller several times to
switch the display of the main unit as follows.
0 For details on the effects of each of the listening modes
see "Listening Mode Effects" (P36). For listening modes
selectable for each of the audio formats in the input
signals, refer to "Selectable listening modes" (P38).
0 The listening mode last selected for the source is
remembered for each of the MOVIE/TV, MUSIC, and
GAME buttons. If content you play is not supported by
the listening mode you selected last, the listening mode
that is standard for that content is selected automatically.
0 The Pure Audio listening mode (P38) can also be
selected by pressing PURE AUDIO on the front of the
main unit. Selecting this mode lights the PURE AUDIO
indicator on the unit. Pressing PURE AUDIO again
reselects the previous listening mode.
a
Input source and volume
Listening mode
b
Input format
The display changes in a
few seconds.
Sampling frequency
Input resolution
En 35
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Listening Mode Effects
Updating of listening modes
We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. This means
that the selectable listening modes depend on the version
of firmware.
On firmware version before Dolby Atmos support
0 Dolby Pro Logic II-related modes can be selected.
On firmware versions supporting Dolby Atmos
0 You can select Dolby Atmos, Dolby Surround, and
Surround Enhancer. (Dolby Pro Logic II-related modes
cannot be selected after updating.) Also, when Surround
Enhancer can be selected, T-D (Theater-Dimensional)
cannot be selected.
In alphabetical order
AllCh Stereo
Ideal for background music, this mode fills the entire
listening area with stereo sound from the front, surround,
and surround back speakers.
Direct
This listening mode can be selected for all input signals.
Processing that affects sound quality is shut down so sound
closer to the original is reproduced. Speakers play the
sound field according to the number of channels in the input
signal, so there would be output from only the front
speakers for a two-channel signal, for example.
Dolby Atmos
This mode faithfully reproduces the sound design recorded
in the Dolby Atmos format.
The Dolby Atmos audio format has been implemented in
movie theaters equipped with the latest facilities and
enables a revolutionary sound experience in home
theaters. Unlike existing surround systems, Dolby Atmos
doesn't rely on channels, but rather enables the accurate
36
placement of sound objects that have independent motion
in a three-dimensional space with even greater clarity.
Dolby Atmos is an optional audio format on Blu-ray Discs
and achieves a three-dimensional sound field by
introducing a sound field above the listener.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
signal to 5.1 channels to suit the connected speaker
configuration when the input signal is 2 channel.
Broadening the sound field provides you with a seamless
sound with more depth and realism. Along with CD and
movie sources, games can also benefit from the vivid
sound localization. Choose from a mode ideal for movies
(Movie), a mode ideal for music (Music), and a mode ideal
for gaming (Game).
Dolby D (Dolby Digital)
This mode faithfully reproduces the sound design recorded
in the Dolby Digital format.
Dolby Digital is a multi-channel digital format developed by
Dolby Laboratories, Inc. widely adopted for use in movie
production. It is also a standard audio format on DVD-Video
and Blu-ray Discs. It is possible to record a maximum of 5.1
channels on a DVD-Video or Blu-ray Disc; two front
channels, a center channel, two surround channels, and
the LFE channel dedicated to the bass region (sound
elements for the subwoofer).
0 To enable transfer of this audio format, connect via digital
cable and set audio output on the player to bitstream
output.
Dolby Surround
This listening mode allows you to expand input signals with
2 channels, etc., to multiple channels to suit the
configuration of connected speakers. Along with past
speaker setups, this is also compatible with playback
systems for Dolby Atmos that include Dolby speaker
technology.
Dolby D+ (Dolby Digital Plus)
This mode faithfully reproduces the sound design recorded
in the Dolby Digital Plus format.
The Dolby Digital Plus format is a revision based on Dolby
Digital, increasing the number of channels and endeavoring
to improve sound quality by giving more flexibility in data bit
rates. Dolby Digital Plus is used as an optional audio format
on Blu-ray Discs, based on 5.1 channels, but with additional
channels such as the surround back channel added for a
maximum of 7.1 channels.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
Dolby PL II (Dolby Pro Logic II)
This listening mode allows you to expand the playback
Dolby TrueHD
This mode faithfully reproduces the sound design recorded
in the Dolby TrueHD format.
The Dolby TrueHD audio format is a reversible format
expanded based on the lossless compression technology
referred to as MLP, and it makes it possible to faithfully
reproduce the master audio recorded in the studio. Dolby
TrueHD is used as an optional audio format on Blu-ray
Discs, based on 5.1 channels, but with additional channels
such as the surround back channel added for a maximum
of 7.1 channels. 7.1 channels can be recorded using
96 kHz/24 bit, and 5.1 channels can be recorded using
192 kHz/24 bit.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DSD
Mode suitable for playing sources recorded in DSD.
0 This unit supports DSD signals input through HDMI IN.
However, depending on the connected player, better
sound is possible when output from the PCM output of
the player.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
0 This listening mode cannot be selected if the output
setting on your Blu-ray Disc/DVD player is not set to
DSD.
DTS
This mode faithfully reproduces the sound design recorded
in the DTS format.
The DTS audio format is a multi-channel digital format
developed by DTS, Inc.. This format is an optional audio
format on DVD-Video and a standard on Blu-ray Discs. It
enables recording of 5.1 channels; two front channels, a
center channel, two surround channels, and the LFE
channel dedicated to the bass region (sound elements for
the subwoofer). The content is recorded with a rich volume
of data, with maximum sampling rate of 48 kHz at a
resolution of 24 bits and a bit rate of 1.5 Mbps.
0 To enable transfer of this audio format, connect via digital
cable and set audio output on the player to bitstream
output.
DTS 96/24
This mode faithfully reproduces the sound design recorded
in the DTS 96/24 format.
DTS 96/24 is an optional audio format on DVD-Video and
Blu-ray Discs. It enables recording of 5.1 channels; two
front channels, a center channel, two surround channels,
and the LFE channel dedicated to the bass region (sound
elements for the subwoofer). Detailed reproduction is
achieved by recording the content at a sampling rate of 96
kHz at a resolution of 24 bits.
0 To enable transfer of this audio format, connect via digital
cable and set audio output on the player to bitstream
output.
DTS Express
This mode faithfully reproduces the sound design recorded
in the DTS Express format.
DTS Express is used as an optional audio format on Blu-ray
Discs, based on 5.1ch, but with channels such as the
surround back channel added for a maximum of 7.1ch. It
also supports low bit rates.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DTS-HD HR (DTS-HD High Resolution Audio)
This mode faithfully reproduces the sound design recorded
in the DTS-HD High Resolution Audio format.
DTS-HD High Resolution Audio is used as an optional
audio format on Blu-ray Discs, based on 5.1ch, but with
additional channels such as the surround back channel
added for a maximum of 7.1ch. It can be recorded at a
sampling rate of 96 kHz with a resolution of 24 bits.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
DTS-HD MSTR (DTS-HD Master Audio)
This mode faithfully reproduces the sound design recorded
in the DTS-HD Master Audio format.
DTS-HD Master Audio is used as an optional audio format
on Blu-ray Discs, based on 5.1ch, but with additional
channels such as the surround back channel added for a
maximum of 7.1ch, recorded using lossless audio
reproduction technology. 96 kHz/24bit is supported with 7.1
channel, and 192 kHz/24bit is supported with 5.1 channel.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
methodology based on past channel based formats and
object based dynamic audio mixing, and it is characterized
by the precise positioning of sounds and the ability to
express movement.
0 To enable transfer of this audio format, connect via HDMI
cable and set audio output on the player to bitstream
output.
Full Mono
In this mode, all speakers output the same sound in mono,
so the sound you hear is the same regardless of where you
are within the listening room.
Game-Action
In this mode, sound localization is distinct with emphasis on
bass.
Game-Rock
In this mode, sound pressure is emphasized to heighten
live feel.
Game-RPG
In this mode, the sound has a dramatic feel with a similar
atmosphere to Orchestra mode.
Game-Sports
Suitable for audio source with much reverberation.
Mono
In this mode, when the input signal is analog or PCM, the
left and right front speakers output the sound in monaural.
DTS Neural:X
This listening mode allows you to expand input signals with
2 channels, etc., to multiple channels to suit the
configuration of connected speakers.
Multich (Multichannel)
Mode suitable for playing sources recorded in multichannel
PCM.
DTS:X
This mode faithfully reproduces the sound design recorded
in the DTS:X format.
The DTS:X audio format is a combination of the mixing
Orchestra
Suitable for classical or operatic music, This mode
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of a
large hall.
En 37
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Pure Audio
This mode reproduces the original sound more faithfully.
The display and analog video circuit are turned off to
provide purer sound.
0 Selecting this mode turns off the analog video circuitry,
so the video signals input through the jacks other than
the HDMI IN jack cannot be displayed on the TV.
Stereo
In this mode, sound is output from the front left and right
speakers and subwoofer.
Studio-Mix
Suitable for rock or pop music, Listening to music in this
mode creates a lively sound field with a powerful acoustic
image, like being at a club or rock concert.
Surround Enhancer
This mode allows you to enjoy sound with a rich sound
field, enveloping you naturally without relying on reflections
from walls. A virtual surround channel is created to give you
a broader sound field.
T-D (Theater-Dimensional)
In this mode, you can enjoy a virtual playback of
multichannel surround sound even when surround
speakers have not been installed. This works by controlling
how sounds reach the listener’s left and right ears.
TV Logic
Suitable for TV shows broadcast from TV studios. This
mode enhances the surround effects to the entire sound to
give clarity to voices and create a realistic acoustic image.
Unplugged
Suitable for acoustic instruments, vocals and jazz, This
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
38
Selectable listening modes
MOVIE/TV
You can select a variety of listening modes to suit the audio
format of the signal being input.
0 Listening modes available when headphones are
connected are Pure Audio, Mono, Direct, and Stereo
only.
This is a list of listening modes you can select according to
the audio format of the input signal.
Input format
Analog
Listening Mode
Direct
Updating of listening modes
We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit. This means
that the selectable listening modes depend on the version
of firmware.
Mono
On firmware version before Dolby Atmos support
0 Dolby Pro Logic II-related modes can be selected.
DTS Neural:X
On firmware versions supporting Dolby Atmos
0 You can select Dolby Atmos, Dolby Surround, and
Surround Enhancer. (Dolby Pro Logic II-related modes
cannot be selected after updating.) Also, when Surround
Enhancer can be selected, T-D (Theater-Dimensional)
cannot be selected.
AllCh Stereo*3
Dolby Surround
Surround Enhancer
PL II Movie*1
TV Logic*2
Full Mono*3
T-D
*1:
*2:
*3:
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Listening Mode
Input format
PCM
Music files (except DSD/
Dolby TrueHD)
Direct
Multich PCM
Direct
DSD
Direct
Mono
Multich*1
DSD*1*2
Dolby Surround
Dolby Surround
Dolby Surround
Surround Enhancer
Surround Enhancer
Surround Enhancer
DTS Neural:X
PL II Movie*3
Logic*2
DTS Neural:X
PL II
Movie*1
TV
DTS Neural:X
TV
Logic*2
AllCh
AllCh
Stereo*3
Full
Full Mono*3
T-D
*1:
*2:
*3:
Listening Mode
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Stereo*3
TV Logic*4
Mono*3
AllCh Stereo*5
Full Mono*5
T-D
*1:
*2:
*3:
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
T-D
*1:
*2:
*3:
*4:
*5:
Cannot be selected when the input format is monaural or 2
ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 39
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Dolby Atmos
Direct
Dolby D+
Listening Mode
Input format
Direct
Dolby TrueHD
Dolby D+*1*2*3
Dolby TrueHD*1*2
Surround Enhancer
Dolby Surround
Dolby Surround
TV Logic
Surround Enhancer
Surround Enhancer
PL II
Movie*4
PL II Movie*3
Logic*5
Full Mono
TV
T-D
AllCh Stereo*6
Full
TV Logic*4
AllCh Stereo*5
Mono*6
Full Mono*5
T-D
Input format
Listening Mode
Dolby D
Direct
Dolby D*1*2
Dolby Surround
Surround Enhancer
PL II Movie*3
TV Logic*4
AllCh Stereo*5
Full Mono*5
T-D
*4:
*5:
40
Direct
Dolby Atmos
AllCh Stereo
*1:
*2:
*3:
Listening Mode
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
*1:
*2:
*3:
*4:
*5:
*6:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Dolby D+ cannot be selected if the input source is Blu-ray
Disc. You can select the Dolby D listening mode instead.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
T-D
*1:
*2:
*3:
*4:
*5:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
DTS
Direct
DTS 96/24
Input format
Direct
DTS Express
Listening Mode
Direct
DTS*1*2
DTS 96/24*1*2
DTS Express*1*2
DTS Neural:X
DTS Neural:X
DTS Neural:X
TV Logic*3
TV Logic*3
TV Logic*3
AllCh Stereo*4
AllCh Stereo*4
AllCh Stereo*4
Full
Mono*4
Full
T-D
*1:
*2:
*3:
*4:
Listening Mode
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Mono*4
Full Mono*4
T-D
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
T-D
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 41
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Listening Mode
MUSIC
DTS-HD HR
Direct
DTS-HD MSTR
Direct
This is a list of listening modes you can select according to
the audio format of the input signal.
DTS-HD
HR*1*2
DTS-HD
DTS Neural:X
DTS Neural:X
Logic*3
Logic*3
TV
AllCh
Full
TV
Stereo*4
AllCh
Mono*4
Full
T-D
*1:
*2:
*3:
*4:
MSTR*1*2
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Input format
Listening Mode
Analog
Pure Audio
Direct
Stereo*4
Stereo
Mono*4
Dolby Surround
T-D
*1:
*2:
*3:
*4:
Surround Enhancer
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
PL II Music*1
DTS Neural:X
Orchestra*2
Unplugged*2
Input format
Listening Mode
Studio-Mix*2
DTS:X
Direct
AllCh Stereo*3
DTS:X
Full Mono*3
TV
Logic*1
AllCh Stereo*2
Full Mono*2
T-D
*1:
*2:
42
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
*1:
*2:
*3:
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
PCM
Music files (except DSD/
Dolby TrueHD)
Pure Audio
Multich PCM
Input format
Listening Mode
Pure Audio
DSD
Pure Audio
Direct
Direct
Direct
Stereo
Stereo
Stereo
Dolby Surround
Multich*1
DSD*1*2
Surround Enhancer
Dolby Surround
Dolby Surround
PL II Music*1
Surround Enhancer
Surround Enhancer
DTS Neural:X
DTS Neural:X
PL II Music*3
Orchestra*2
Orchestra*2
DTS Neural:X
Unplugged*2
Unplugged*2
Orchestra*4
Studio-Mix*2
Studio-Mix*2
Unplugged*4
AllCh Stereo*3
AllCh Stereo*3
Studio-Mix*4
Full
*1:
*2:
*3:
Listening Mode
Mono*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full
*1:
*2:
*3:
Mono*3
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
AllCh Stereo*5
Full Mono*5
*1:
*2:
*3:
*4:
*5:
Cannot be selected when the input format is monaural or 2
ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 43
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Dolby Atmos
Pure Audio
Dolby D
Listening Mode
Input format
Listening Mode
Pure Audio
Dolby D+
Pure Audio
Direct
Direct
Direct
Stereo
Stereo
Stereo
Dolby Atmos
Dolby D*1*2
Dolby D+*1*2*3
Surround Enhancer
Dolby Surround
Dolby Surround
Orchestra
Surround Enhancer
Surround Enhancer
Unplugged
PL II
Music*3
Studio-Mix
Orchestra*4
Orchestra*5
AllCh Stereo
Unplugged*4
Unplugged*5
Full Mono
Studio-Mix*4
Studio-Mix*5
AllCh Stereo*5
AllCh Stereo*6
Full
*1:
*2:
*3:
*4:
*5:
44
PL II Music*4
Mono*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full Mono*6
*1:
*2:
*3:
*4:
*5:
*6:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Dolby D+ cannot be selected if the input source is Blu-ray
Disc. You can select the Dolby D listening mode instead.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Dolby TrueHD
Pure Audio
DTS
Pure Audio
DTS 96/24
Listening Mode
Pure Audio
Direct
Direct
Stereo
Stereo
Stereo
Dolby TrueHD*1*2
DTS*1*2
DTS 96/24*1*2
Dolby Surround
DTS Neural:X
DTS Neural:X
Surround Enhancer
Orchestra*3
Orchestra*3
PL II Music*3
Unplugged*3
Unplugged*3
Orchestra*4
Studio-Mix*3
Studio-Mix*3
Unplugged*4
AllCh Stereo*4
AllCh Stereo*4
AllCh Stereo*5
Full
*4:
*5:
Input format
Direct
Studio-Mix*4
*1:
*2:
*3:
Listening Mode
Mono*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full
*1:
*2:
*3:
*4:
Mono*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full Mono*4
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 45
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
DTS Express
Listening Mode
Input format
Pure Audio
DTS-HD HR
46
Input format
Listening Mode
Pure Audio
DTS-HD MSTR
Pure Audio
Direct
Direct
Direct
Stereo
Stereo
Stereo
DTS Express*1*2
DTS-HD HR*1*2
DTS-HD MSTR*1*2
DTS Neural:X
DTS Neural:X
DTS Neural:X
Orchestra*3
Orchestra*3
Orchestra*3
Unplugged*3
Unplugged*3
Unplugged*3
Studio-Mix*3
Studio-Mix*3
Studio-Mix*3
AllCh Stereo*4
AllCh Stereo*4
AllCh Stereo*4
Full
*1:
*2:
*3:
*4:
Listening Mode
Mono*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full
*1:
*2:
*3:
*4:
Mono*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full Mono*4
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
DTS:X
Listening Mode
GAME
Input format
Listening Mode
Pure Audio
This is a list of listening modes you can select according to
the audio format of the input signal.
PCM
Music files (except DSD/
Dolby TrueHD)
Direct
Direct
Stereo
Listening Mode
DTS:X
Analog
Direct
PL II Game*1
Orchestra*1
Dolby Surround
DTS Neural:X
Unplugged*1
Surround Enhancer
Game-RPG*2
Studio-Mix*1
PL II Game*1
Game-Action*2
DTS Neural:X
Game-Rock*2
Game-RPG*2
Game-Sports*2
Game-Action*2
AllCh Stereo*3
Game-Rock*2
Full Mono*3
AllCh
Stereo*2
Full Mono*2
*1:
*2:
Dolby Surround
Input format
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Surround Enhancer
Game-Sports*2
AllCh Stereo*3
Full Mono*3
T-D
*1:
*2:
*3:
T-D
*1:
*2:
*3:
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 47
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Listening Mode
Input format
Multich PCM
Direct
DSD
Direct
Dolby Atmos
DSD*1*2
Dolby Atmos
Dolby Surround
Dolby Surround
Surround Enhancer
Surround Enhancer
Surround Enhancer
Game-RPG
Game*3
Game-Action
DTS Neural:X
PL II
Game-RPG*2
DTS Neural:X
Game-Rock
Game-Action*2
Game-RPG*4
Game-Sports
Game-Rock*2
Game-Action*4
AllCh Stereo
Game-Sports*2
Game-Rock*4
Full Mono
AllCh Stereo*3
Game-Sports*4
T-D
Mono*3
AllCh
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Stereo*5
Full Mono*5
T-D
T-D
*1:
*2:
*3:
*4:
*5:
48
Direct
Multich*1
Full
*1:
*2:
*3:
Listening Mode
Cannot be selected when the input format is monaural or 2
ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Dolby D
Direct
Dolby D+
Direct
Dolby TrueHD
Listening Mode
Direct
Dolby D+*1*2*3
Dolby TrueHD*1*2
Dolby Surround
Dolby Surround
Dolby Surround
Surround Enhancer
Surround Enhancer
Surround Enhancer
Game*3
Game*4
PL II Game*3
Game-RPG*4
Game-RPG*5
Game-RPG*4
Game-Action*4
Game-Action*5
Game-Action*4
Game-Rock*4
Game-Rock*5
Game-Rock*4
Game-Sports*4
Game-Sports*5
Game-Sports*4
AllCh
PL II
Stereo*5
AllCh
Full Mono*5
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Stereo*6
AllCh Stereo*5
Full Mono*6
T-D
*4:
*5:
Input format
Dolby D*1*2
PL II
*1:
*2:
*3:
Listening Mode
Full Mono*5
T-D
*1:
*2:
*3:
*4:
*5:
*6:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Dolby D+ cannot be selected if the input source is Blu-ray
Disc. You can select the Dolby D listening mode instead.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
T-D
*1:
*2:
*3:
*4:
*5:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Can only be selected when the input format is 2 ch and a
center speaker or surround speakers are installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 49
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
DTS
Direct
DTS 96/24
Direct
DTS Express
Listening Mode
Direct
DTS 96/24*1*2
DTS Express*1*2
DTS Neural:X
DTS Neural:X
DTS Neural:X
Game-RPG*3
Game-RPG*3
Game-RPG*3
Game-Action*3
Game-Action*3
Game-Action*3
Game-Rock*3
Game-Rock*3
Game-Rock*3
Game-Sports*3
Game-Sports*3
Game-Sports*3
Stereo*4
AllCh
Full Mono*4
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Stereo*4
AllCh Stereo*4
Full Mono*4
T-D
50
Input format
DTS*1*2
AllCh
*1:
*2:
*3:
*4:
Listening Mode
Full Mono*4
T-D
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
T-D
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Input format
Listening Mode
Input format
Listening Mode
Input format
DTS-HD HR
Direct
DTS-HD MSTR
Direct
DTS:X
Direct
DTS-HD HR*1*2
DTS-HD MSTR*1*2
DTS:X
DTS Neural:X
DTS Neural:X
Game-RPG*1
Game-RPG*3
Game-RPG*3
Game-Action*1
Game-Action*3
Game-Action*3
Game-Rock*1
Game-Rock*3
Game-Rock*3
Game-Sports*1
Game-Sports*3
Game-Sports*3
AllCh Stereo*2
AllCh
*1:
*2:
*3:
*4:
Listening Mode
Stereo*4
AllCh
Stereo*4
Full Mono*4
Full Mono*4
T-D
T-D
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
*1:
*2:
*3:
*4:
Cannot be selected when the input format is 2 ch.
A center speaker or surround speakers need to be installed.
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
Full Mono*2
T-D
*1:
*2:
Surround speakers or height speakers need to be installed.
A center speaker, surround speakers, or height speakers
need to be installed.
En 51
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Setup Menu
Advanced Setup
The unit allows you to configure advanced settings to provide you with an even better
experience.
1. Switch the input on the TV to that assigned to the unit.
2. Press
on the remote controller to display the Setup menu screen.
1
INPUT
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Video Input
4. Source
4. Digital Audio Input
5. Hardware
5. Analog Audio Input
6. Miscellaneous
TV
2
3. Select the item with S / T on the remote controller and press ENTER to confirm your
selection.
0 Change the initial values for each of the settings with the cursors W / X.
0 To return to the previous screen, press
.
4. To exit the settings, press .
1. Input/Output Assign
∫ 1. TV Out / OSD
52
OSD Language
Select the on-screen display language.
English, German, French, Spanish, Italian, Dutch, Swedish,
Russian, Chinese
Impose OSD
Set whether or not to display the information on the TV when the
volume is adjusted or input is changed, for example.
"On (default value)": Display OSD on the TV
"Off": Do not display OSD on the TV
0 OSD may not be displayed depending on the input signal
even if "On" is selected. If the operation screen is not
displayed, change the resolution of the connected device.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Mini Player OSD
Screen Saver
You can play on the TV the images from another input selected
immediately prior while you are playing the audio from NET or
BLUETOOTH input. After switching to NET or BLUETOOTH,
play the images and audio, then when you press MODE on the
remote controller, the image is displayed in full-screen mode,
and the audio information (Mini Player) for NET or BLUETOOTH
is displayed in the corner of the screen. You can set whether to
display this Mini Player on the screen all the time.
"Always On (default value)": The Mini Player is displayed all the
time.
"Auto Off": The Mini Player turns off automatically 30 seconds
after being displayed. It is displayed for 30 seconds after
operations such as changing the volume.
0 Each press of the MODE button displays or turns off the
video.
0 This cannot be selected if "Impose OSD" is set to "Off".
0 The Mini Player display feature is not available when Chinese
is selected as the OSD language.
GAME
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the GAME input selector. If you do not assign a
jack, select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "HDMI 4 (HDCP 2.2)")
STRM BOX
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the STRM BOX input selector. If you do not
assign a jack, select "---". To select an HDMI IN jack already
assigned to another input selector, change the input selector
setting to "---" first. (Default Value is "HDMI 3 (HDCP 2.2)")
PC
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the PC input selector. If you do not assign a
jack, select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "---")
CD
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the CD input selector. If you do not assign a
jack, select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "---")
TV
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the TV input selector. If you do not assign a jack,
select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "---")
Set the time to start the screen saver.
Select "3 minutes (default value)", "5 minutes", "10 minutes", or
"Off".
∫ 2. HDMI Input
You can change input assignment between the input selectors and HDMI IN jacks.
BD/DVD
CBL/SAT
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the BD/DVD input selector. If you do not assign
a jack, select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "HDMI 1 (HDCP 2.2)")
"HDMI 1 (HDCP 2.2)" to "HDMI 4 (HDCP 2.2)": Assign a desired
HDMI IN jack to the CBL/SAT input selector. If you do not assign
a jack, select "---". To select an HDMI IN jack already assigned to
another input selector, change the input selector setting to "---"
first. (Default Value is "HDMI 2 (HDCP 2.2)")
∫ 3. Video Input
You can change input assignment between the input selectors and VIDEO IN jacks. If you
do not assign a jack, select "---".
BD/DVD
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
BD/DVD input selector. (Default Value is "---")
CBL/SAT
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
CBL/SAT input selector. (Default Value is "VIDEO 2")
En 53
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
GAME
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
GAME input selector. (Default Value is "VIDEO 1")
STRM BOX
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
STRM BOX input selector. (Default Value is "---")
PC
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
PC input selector. (Default Value is "---")
CD
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
CD input selector. (Default Value is "---")
TV
"VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the
TV input selector. (Default Value is "---")
∫ 4. Digital Audio Input
You can change input assignment between the input selectors and DIGITAL IN COAXIAL/
OPTICAL jacks. If you do not assign a jack, select "---".
BD/DVD
CBL/SAT
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the CBL/SAT input selector. (Default Value is
"COAXIAL")
GAME
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the GAME input selector. (Default Value is "--")
STRM BOX
54
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the BD/DVD input selector. (Default Value is
"---")
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the STRM BOX input selector. (Default Value
is "---")
PC
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the PC input selector. (Default Value is "---")
CD
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the CD input selector. (Default Value is
"OPTICAL 1")
TV
"COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the TV input selector. (Default Value is
"OPTICAL 2")
0 Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32 kHz,
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 20 bit, 24 bit.
∫ 5. Analog Audio Input
You can change input assignment between the input selectors and AUDIO IN jacks. If you
do not assign a jack, select "---".
BD/DVD
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the BD/DVD input selector. (Default Value is "---")
CBL/SAT
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the CBL/SAT input selector. (Default Value is "---")
GAME
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the GAME input selector. (Default Value is "AUDIO 1")
STRM BOX
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the STRM BOX input selector. (Default Value is "---")
PC
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the PC input selector. (Default Value is "AUDIO 2")
CD
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the CD input selector. (Default Value is "AUDIO 3")
TV
"AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the TV input selector. (Default Value is "---")
2. Speaker
You can make changes to the connection environment of the speakers and change the
volume level. Settings are automatically configured if you use AccuEQ Room Calibration.
This setting cannot be selected if headphones are connected or if "5. Hardware" - "HDMI" "Audio TV Out" is set to "On" so audio is output from the speakers of the TV.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
∫ 1. Configuration
Speaker Channels
Select from "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch (default value)",
"2.1.2 ch", or "3.1.2 ch" to suit the number of speaker channels
connected.
Subwoofer
Set whether a subwoofer is connected or not.
"Yes (default value)": When subwoofer is connected
"No": When subwoofer is not connected
Height Speaker
Set the speaker type if height speakers are connected to the
SURROUND or HEIGHT terminals. Select from "Front High",
"Top Middle (default value)", or "Dolby Speaker (Front)" to suit
the type and layout of the connected speakers.
0 If an item cannot be selected even though connection is
correct, check that the settings in "Speaker Channels"
matches the number of connected channels.
Speaker Impedance
Set the impedance of the connected speakers.
"4ohms": When any of the connected speakers have 4 ≠ or
more to less than 6 ≠ impedance
"6ohms (default value)": When the connected speakers all have
6 ≠ or more impedance
0 For impedance, check the indications on the back of the
speakers or their instruction manual.
Center
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Height
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Surround
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
LPF of LFE
Set the low-pass filter for LFE (low-frequency effect) signals in
order to pass lower frequency signals than the set value and
thus cancel unwanted noises. The low-pass filter will be effective
only on sources with LFE channel.
The value from "80Hz" to "120Hz (default value)" can be set.
"Off": When this function is not to be used
∫ 2. Crossover
Front
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 If "Configuration" - "Subwoofer" is set to "No", "Front" will be
fixed to "Full Band" and the bass range of the other channels
will be output from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
En 55
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Double Bass
This can be selected when the "Configuration" - "Subwoofer"
setting is "Yes" and the "Front" setting is "Full Band".
Boost bass output by sending the bass of the front speakers and
center speaker to the subwoofer.
"On": Bass output will be boosted.
"Off": Bass output will not be boosted.
0 The setting will not automatically be configured even if you
performed AccuEQ Room Calibration.
∫ 3. Distance
∫ 4. Level Calibration
Front Left
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Center
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Front Right
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Left
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Right
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Surround Right
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Surround Left
Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Subwoofer
Select a value between "-15 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Set the distance from each speaker to the listening position.
Front Left
Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Center
Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Front Right
Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Height Left
Specify the distance between each speaker and the listening
position. (Default Value is "2.70 m")
Height Right
Specify the distance between each speaker and the listening
position. (Default Value is "2.70 m")
Surround Right
Specify the distance between each speaker and the listening
position. (Default Value is "2.10 m")
Surround Left
Specify the distance between each speaker and the listening
position. (Default Value is "2.10 m")
Subwoofer
Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
0 Distance units can be switched by pressing MODE on the remote controller. When the
unit is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1 ft. When the
unit is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
56
∫ 5. Dolby Enabled Speaker
Dolby Enabled
Speaker to Ceiling
Set the distance between the Dolby enabled speaker and the
ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/
4.50 m" (in 0.1 ft/0.03 m increments, default value is "1.80 m")
0 The unit of distance (feet/meters) shown is the unit selected
for use in "Distance".
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
AccuReflex
You can enhance the reflection effect of Dolby enabled speaker
from the ceiling.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 The function is not effective if the listening mode is Pure Audio
or Direct.
0 This setting can only be selected when you have set "Configuration" - "Height Speaker" to
"Dolby Speaker".
Subwoofer
0 The result may not be as expected depending on the input source and listening mode
setting.
∫ 6. Equalizer Settings
3. Audio Adjust
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
nine bands for all other speakers. To use the set equalizer effects, select the preset number
in "Quick Menu" - "AccuEQ" - "Equalizer"(P66).
∫ 1. Multiplex/Mono
Front
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors W/X, adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with S/T. (Default
Value is "0.0 dB")
Center
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors W/X, adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with S/T. (Default
Value is "0.0 dB")
Height
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors W/X, adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with S/T. (Default
Value is "0.0 dB")
Surround
After selecting the speaker frequency from between "25 Hz" and
"16 kHz" with the cursors W/X, adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with S/T. (Default
Value is "0.0 dB")
After selecting the speaker frequency from between "25 Hz" and
"160 Hz" with the cursors W/X, adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with S/T. (Default
Value is "0.0 dB")
0 This cannot be selected if "No" is set in "Configuration" "Subwoofer".
Multiplex Input
Channel
Set the audio channel or language to be output when playing
multiplex audio or multilingual TV broadcasts etc.
"Main (default value)": Main channel only
"Sub": Sub channel only
"Main / Sub": Main and sub channels will be output at the same
time.
0 If multiplex audio is being played, "1+1" will be displayed
when
on the remote controller is pressed.
Mono Input Channel
Set the input channel to use for playing any 2 channel digital
source such as Dolby Digital, or analog/PCM source in the Mono
listening mode.
"Left": Left channel only
"Right": Right channel only
"Left + Right (default value)" : Left and right channels
∫ 2. Dolby
Loudness
Management
When playing Dolby TrueHD, enable the dialog normalization
function which keeps the volume of dialog at a certain level. Note
that when this setting is Off while playing Dolby Digital Plus/
Dolby TrueHD, the Late Night function that allows you to enjoy
surround at low volumes is fixed to Off.
"On (default value)": When this function is to be used
"Off": When this function is not to be used
En 57
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
4. Source
∫ 3. DTS
DTS Auto Surround
When inputting DTS signals that include extended channel
information, the optimum listening mode is automatically
selected according to the extended information contained in the
input signal and the speaker configuration of this unit when
playing in the straight decoding listening mode.
"On (default value)": When this function is to be used
"Off": Audio is played using the same amount of channels in the
input signal according to the speaker configuration of this unit.
∫ 1. IntelliVolume
Adjust the volume level difference between the devices connected to the unit. Select the
input selector to configure.
IntelliVolume
Select a value between "-12 dB" and "+12 dB". Set a negative
(j) value if the volume of the target device is larger than the
others and a positive (i) value if smaller. To check the audio,
start playback of the connected device. (Default Value is "0dB")
∫ 4. LFE Level
∫ 2. Name Edit
Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel
PCM, and DSD signals.
Set an easy name to each input. The set name will be shown on the main unit display. Select
the input selector to configure.
LFE Level
Select the low-frequency effect (LFE) level of each type of signal
from "0dB (default value)" to "-¶dB". If the low-frequency effect
sound is too strong, select "-20dB" or "-¶dB".
Name Edit
∫ 5. Volume
1. Select a character or symbol with the cursors and press
ENTER.
Repeat it to input 10 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
MODE on the remote controller also toggles between upper
and lower cases.)
"" "": Moves the cursor to the arrow direction.
"
": Removes a character on the left of the cursor.
" ": Enters a space.
0 Pressing CLEAR on the remote controller will remove all
the input characters.
2. After inputting, select "OK" with the cursors and press
ENTER.
The input name will be saved.
Mute Level
Set the volume lowered from the listening volume when muting
is on. Select a value from "-¶dB (default value)", "-40dB", and "20dB".
Maximum Volume
Set the maximum value to avoid too high volume. Select "Off
(default value)" or a value between "50" to "99".
Power On Volume
Set the volume level of when the power is turned on. Select
"Last (default value)" (volume level before entering standby
mode), "Min", "1" to "99" and "Max".
0 You cannot set a higher value than that of "Maximum
Volume".
0 To name a preset radio station, press TUNER on the remote controller, select AM/FM and
select the preset number.
0 It cannot be set if the "NET" or "BLUETOOTH" input is selected.
Adjust the output level of the headphones. Select a value
between "-12 dB" and "+12 dB". (Default Value is "0dB")
∫ Audio Select
Headphone Level
Select the priority for input selection when multiple audio sources are connected to one input
selector, such as connections to both the "GAME" HDMI IN jack and the "GAME" AUDIO IN
jack. The setting can be separately set to each input selector. Select the input selector to
58
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
configure. Note that there are some default values you cannot change.
Audio Select
PCM Fixed Mode
"ARC": When giving priority to input signal from ARC compatible
TV.
0 The setting can be selected only when "5. Hardware" - "HDMI"
- "Audio Return Channel" is set to "Auto" and also the "TV"
input is selected.
"HDMI": When giving priority to input signal from HDMI IN jacks.
0 The setting can be selected only when the input is assigned to
the HDMI jack in the "1. Input/Output Assign" - "HDMI Input"
setting.
"COAXIAL": When giving priority to input signal from DIGITAL IN
COAXIAL jacks.
0 The setting can be selected only when the input is assigned to
the COAXIAL jack in the "1. Input/Output Assign" - "Digital
Audio Input" setting.
"OPTICAL": When giving priority to input signal from DIGITAL IN
OPTICAL jacks.
0 The setting can be selected only when the input is assigned to
the OPTICAL jack in the "1. Input/Output Assign" - "Digital
Audio Input" setting.
"Analog": To always output analog audio independently of the
input signal
0 The setting can be selected only when the input is assigned to
the AUDIO jack in the "1. Input/Output Assign" - "Analog
Audio Input" setting.
(Default value: BD/DVD: HDMI, CBL/SAT: HDMI, GAME: HDMI,
STRM BOX: HDMI, PC: Analog, AUX: Analog, CD: OPTICAL,
TV: OPTICAL)
0 This setting cannot be changed if the "TUNER", "NET" or "BLUETOOTH" input is
selected.
∫ Video Select
When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from
which video is displayed on the TV.
Video Select
"Last (default value)": Select the video input played immediately
prior.
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "CD",
"TV": Play the video from the selected input.
0 This setting is effective for input selectors assigned in "1.
Input/Output Assign" - "HDMI Input" and "Video Input".
0 If the OSD language is set to Chinese, you can only select this setting when "TUNER" is
selected as input.
Select whether to fix input signals to PCM (except multi-channel
PCM) when you have selected "HDMI", "COAXIAL", or
"OPTICAL" in the "Audio Select" setting. Set this item to "On" if
noise is produced or truncation occurs at the beginning of a track
when playing PCM sources. Select "Off (default value)" normally.
0 The setting to changes to "Off" each time the "Audio Select"
setting is changed.
En 59
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
5. Hardware
HDMI Standby
Through
∫ 1. HDMI
HDMI CEC
60
Setting to "On" enables the input selection link and other link
functions with HDMI connected CEC compliant device.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
When changing this setting, turn off and then on again the power
of all connected components.
0 Depending on the TV you have, link settings may be needed
on the TV.
0 Setting to "On" and closing the on-screen menu displays the
name of the CEC-compatible components and "CEC On" on
the display.
0 Power consumption in standby mode may increase if "On" is
set. (Depending on the TV status, the unit will enter the
normal standby mode.)
0 If you operate the volume dial on this unit when this setting is
"On" and audio is output from the TV speakers, audio will be
output also from the speakers connected to the unit. If you
want to output from only one of them, change the unit or TV
settings, or reduce the volume of the unit.
0 If abnormal operation occurs when you set the setting to "On",
set it to "Off".
0 When connecting a non-CEC compatible component, or when
you are not sure whether it is compatible, set the setting to
"Off".
When this is set to anything other than "Off", you can play the
video and audio of an HDMI connected player on the TV even if
the unit is in standby mode. Only "Auto" and "Auto (Eco)" can be
selected if "HDMI CEC" is set to "On". If you select anything
else, set "HDMI CEC" to "Off". (Default Value is "Off")
0 Power consumption when this unit is in standby mode
increases if set to anything other than "Off".
"BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "CD",
"TV": For example, if you select "BD/DVD", you can play the
equipment connected to the "BD/DVD" jack on the TV even if the
unit is in standby mode. Select this setting if you have decided
which player to use with this function.
"Last": You can play the video and audio of the input selected
immediately prior to the unit being switched to standby on the
TV. When "Last" is selected, you can switch the input of the unit
with the remote controller even in the standby mode.
"Auto", "Auto (Eco)": Select one of these settings when you have
connected equipment that conforms to the CEC standard. You
can play the video and audio of the input selected on the TV,
irrespective of what input was selected immediately prior to the
unit being switched to standby, using the CEC link function.
0 To play players on the TV that do not conform to the CEC
standard, you will need to turn the unit on and switch to the
relevant input.
0 When using a TV that conforms to the CEC standard, you can
reduce the power consumption in standby mode by selecting
"Auto (Eco)".
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Audio TV Out
Audio Return Channel
Auto Lip Sync
You can enjoy audio through the speakers of the TV while this
unit is on.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 The setting is fixed to "Auto" if "HDMI CEC" is set to "On". If
you change this setting, set "HDMI CEC" to "Off"
0 The listening mode cannot be changed while "Audio TV Out"
is set to "On" and audio is being output through the speakers
of the TV.
0 Depending on your TV set or input signal of the component,
audio may not output through the speakers of the TV even if
this setting is set to "On". In such case, audio is output from
the speakers of the unit.
0 If you operate the volume dial on this unit when audio that is
being input through this unit for output from the TV speakers,
audio is output from this unit. If you do not want to output
audio from the unit, change the unit or TV settings, or reduce
the volume of the unit.
You can enjoy sound of the HDMI connected ARC compatible
TV through the speakers connected to the unit.
To use this function, set "HDMI CEC" to "On" in advance.
"Auto": To enjoy the TV sound through the speakers connected
to this unit
"Off": When not using the ARC function
This setting automatically corrects any desynchronization
between the video and audio signals based on data from the
HDMI LipSync compatible TV.
"On (default value)": Automatic correction will be enabled.
"Off": Automatic correction will be disabled.
Wi-Fi
Connect the unit to network via wireless LAN router.
"On": Wireless LAN connection
"Off (Wired) (default value)": To connect via wired LAN
Wi-Fi Setup
You can configure wireless LAN settings by pressing ENTER
when "Start" is displayed.
0 Refer to "3. Network Connection" (P21) in Initial Setup for WiFi settings.
Wi-Fi Status
The information for the connected access point is displayed.
"SSID": The SSID of the connected access point
"Signal": The signal strength of the connected access point
"Status": The status of the connected access point
MAC Address
This is the MAC address of the AV receiver.
This value is specific to the component and cannot be changed.
DHCP
"Enable (default value)": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
If "Disable" is selected, you must set "IP Address", "Subnet
Mask", "Gateway", and "DNS Server" manually.
IP Address
Displays/Sets the IP address.
Subnet Mask
Displays/Sets the subnet mask.
Gateway
Displays/Sets the gateway.
DNS Server
Displays/Sets the primary DNS server.
Proxy URL
Displays/Sets the proxy server URL.
Proxy Port
Displays/Sets the proxy server port number when you enter
"Proxy URL".
∫ 2. Network
0 When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting
automatically. Further, to assign fixed IP addresses to each component, you must set
"DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set
information related to your LAN, such as Subnet Mask and Gateway.
En 61
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Friendly Name
AirPlay Password
62
Change the device name for this unit which is shown on other
devices connected to the network to an easily recognized name.
This is set to Onkyo TX-NR474****** at the time of purchase. (*
stand for alphanumeric characters identifying each unit)
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors and press
ENTER.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
MODE on the remote controller also toggles between upper
and lower cases.)
"" "": Moves the cursor to the arrow direction.
"
": Removes a character on the left of the cursor.
" ": Enters a space.
0 Pressing CLEAR on the remote controller will remove all the
input characters.
3. After inputting, select "OK" with the cursors and press
ENTER.
The input name will be saved.
You can set a password of up to 31 characters so that only
registered users can use AirPlay.
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors and press
ENTER.
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing
MODE on the remote controller also toggles between upper
and lower cases.)
"" "": Moves the cursor to the arrow direction.
"
": Removes a character on the left of the cursor.
" ": Enters a space.
0 To select whether to mask the password with "¢" or display it
in plain text, press MEMORY on the remote control.
0 Pressing CLEAR on the remote controller will remove all the
input characters.
3. After inputting, select "OK" with the cursors and press
ENTER.
The input password will be saved.
Usage Data
As a means of improving the quality of our products and
services, we may collect information about your usage over the
network. Select "Yes" if you agree to our collecting this
information. Select "No" if you do not want us to collect this
information. (Default Value is "No")
You can set this after confirming the Privacy Policy. When you
select "Usage Data" and press ENTER, the Privacy Policy is
displayed. (The same screen is displayed once also when
setting up the network connection.) If you agree to the collection
of the information, this setting also becomes "Yes". Note that if
you agree to the Privacy Policy but select "No" for this setting,
the information will not be collected.
Network Check
You can check the network connection.
Press ENTER when "Start" is displayed.
0 Wait for a while if "Network" cannot be selected. It will appear when the network feature is
started.
∫ 3. Bluetooth
Bluetooth
Select whether or not to use the BLUETOOTH function.
"On (default value)": Enables connection with a BLUETOOTH
wireless technology enabled device by using the BLUETOOTH
function. Select "On" also when making various BLUETOOTH
settings.
"Off": When the BLUETOOTH function is not to be used
Auto Input Change
The input of the unit will automatically be switched to
"BLUETOOTH" when connection is made from a BLUETOOTH
wireless technology enabled device to the unit.
"On (default value)": The input will automatically become
"BLUETOOTH" when a BLUETOOTH wireless technology
enabled device is connected.
"Off": The function is disabled.
0 If the input is not switched automatically, set to "Off" and
change the input manually.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Auto Reconnect
This function automatically reconnects to the BLUETOOTH
wireless technology enabled device connected last when you
change the input to "BLUETOOTH".
"On (default value)": When this function is to be used
"Off": When this function is not to be used
0 This may not work with some BLUETOOTH wireless
technology enabled devices.
Pairing Information
You can initialize the pairing information saved on this unit.
Pressing ENTER when "Clear" is displayed initializes the pairing
information stored in this unit.
0 This function does not initialize the pairing information on the
BLUETOOTH wireless technology enabled device. When
pairing the unit again with the device, be sure to clear the
pairing information on the BLUETOOTH wireless technology
enabled device in advance. For information on how to clear
the pairing information, refer to the BLUETOOTH wireless
technology enabled device's instruction manual.
Device
Displays the name of the BLUETOOTH wireless technology
enabled device connected to the unit.
0 The name is not displayed when "Status" is "Ready" or
"Pairing".
Status
Displays the status of the BLUETOOTH wireless technology
enabled device connected to the unit.
"Ready": Not paired
"Pairing": Pairing
"Connected": Successfully connected
Auto Standby
This setting places the unit on standby automatically after 20
minutes of inactivity without any video or audio input. (When
"USB Power Out at Standby" or "Network Standby" is on, this
becomes the HYBRID STANDBY mode which reduces the
increase in power consumption to a minimum.)
"On (default value)": The unit will automatically enter standby
mode. "AUTO STBY" lights on the display.
"Off": The unit will not automatically enter standby mode.
0 "Auto Standby" is displayed on the display and TV screen 30
seconds before the Auto Standby comes on.
Auto Standby in HDMI
Standby Through
Enable or disable "Auto Standby" while "HDMI Standby Through"
is on.
"On": Enable this function
"Off": The setting will be disabled.
0 This setting cannot be set to "On" if "Auto Standby" and
"HDMI" - "HDMI Standby Through" are set to "Off".
USB Power Out at
Standby
Devices connected to the USB port are supplied with electricity
even when this unit is in standby mode when this function is
"On".
(Default Value is "Off")
0 When using this feature, power consumption increases even
when this unit is on standby, however, the increase in power
consumption is kept to a minimum by automatically entering
the HYBRID STANDBY mode, where only essential circuits
are operating.
0 Wait for a while if "Bluetooth" cannot be selected. It will appear when the BLUETOOTH
function is started up.
∫ 4. Power Management
Sleep Timer
Allows the unit to enter standby automatically when the specified
time elapses. Select "30 minutes", "60 minutes", or "90 minutes".
"Off (default value)": Does not turn the unit to standby
automatically.
En 63
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Network Standby
Bluetooth Wakeup
When this feature is turned "On (default value)", you can turn on
the power of the unit via the network using an application that
can control this unit.
0 When using "Network Standby", power consumption
increases even when this unit is on standby, however, the
increase in power consumption is kept to a minimum by
automatically entering the HYBRID STANDBY mode, where
only essential circuits are operating.
0 When the connection to the network is lost, "Network
Standby" is disabled to reduce power consumption. Use the
power button on the remote controller or main unit to turn the
unit on if this happens.
This function wakes up the unit on standby by connecting a
BLUETOOTH wireless technology enabled device.
"On": When this function is to be used
"Off (default value)": When this function is not to be used
0 When this setting is turned "On", power consumption
increases even when this unit is on standby, however, the
increase in power consumption is kept to a minimum by
automatically entering the HYBRID STANDBY mode, where
only essential circuits are operating.
0 The setting is fixed to "Off" if "5. Hardware" - "Bluetooth" "Auto Input Change" is set to "Off".
0 Wait for a while if "Network Standby" or "Bluetooth Wakeup" cannot be selected. It will
appear when the network feature is started.
∫ 2. Remote ID
Remote ID
∫ 3. Firmware Update
Update Notice
Availability of a firmware update will be notified via network.
"Enable (default value)": Notify updates
"Disable": Disable notifications
Version
The current firmware version will be displayed.
Update via NET
Press ENTER to select when you want to update the firmware
via network.
0 You will not be able to select this setting if you do not have
Internet access or there is nothing to update.
Update via USB
Press ENTER to select when you want to update the firmware
via USB.
0 You will not be able to select this setting if a USB storage
device is not connected or there is nothing to update in the
USB storage device.
6. Miscellaneous
∫ 1. Tuner
AM Frequency Step
Select a frequency step depending on your area of residence.
Select "10 kHz" or "9 kHz (default value)".
0 When this setting is changed, all radio presets are deleted.
Select an ID for the unit's remote controller from "1 (default
value)", "2", and "3" to prevent interference between the unit and
other ONKYO components that are installed in the same room.
After changing the ID on the main unit, change the ID on the
remote controller accordingly with the following procedure.
While holding down MODE, press the following buttons for about
3 seconds.
0 To change the remote controller ID to "1": :
(The remote indicator flashes once.)
0 To change the remote controller ID to "2": X/h
(The remote indicator flashes twice.)
0 To change the remote controller ID to "3": 9
(The remote indicator flashes three times.)
0 Wait for a while if "Firmware Update" cannot be selected. It will appear when the network
feature is started.
∫ 4. Initial Setup
You can make the Initial Setup from the Setup menu.
0 Wait for a while if "Initial Setup" cannot be selected. It will appear when the network
64
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
feature is started.
∫ 5. Lock
Setup Parameter
Lock the Setup menu to protect the settings.
"Locked": The menu is locked.
"Unlocked (default value)": Unlocked
En 65
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Quick Menu
1
By pressing the Q button on the remote controller during play, you can adjust frequently
used settings, such as the sound quality, using on-screen menus.
1. Press Q on the remote controller to display the Quick Menu.
Quick Menu
BD/DVD
Tone
Bass
Level
Treble
AccuEQ
Other
2. Select the item with S / T on the remote controller and press ENTER to confirm your
selection.
0 Change the initial values for each of the settings with the cursors W / X.
0 To return to the previous screen, press
.
3. To exit the settings, press Q.
∫ Tone
Bass: Enhance or moderate the bass range of the front speakers.
Treble: Enhance or moderate the treble range of the front speakers.
0 It cannot be set if the listening mode is Pure Audio or Direct.
∫ Level
Center: Adjust the speaker level of the center speaker while listening to some sound.
Subwoofer: Adjust the speaker level of the subwoofer while listening to some sound.
0 The adjustment you made will be reset to the previous status when you turn the unit to
standby mode.
∫ AccuEQ
AccuEQ Room Calibration: Enable or disable the equalizer function that corrects for
distortion caused by the acoustic environment of the room. If this is to be enabled, then
normally you should select "On (All Ch)", and to disable just the front speakers you should
select "On (ex. L/R)". The setting can be separately set to each input selector.
0 This setting cannot be selected if AccuEQ Room Calibration has not been performed.
Equalizer: Select "Preset 1" to "Preset 3" configured in "2. Speaker" - "Equalizer Settings"
66
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
(P57) in the Setup menu. The same sound field setting is applied all ranges when set to
"Off".
Cinema Filter: Adjust the soundtrack that was processed to enhance its high pitch range, in
order to make it suitable for home theater. This function can be used in the following
listening modes: Dolby Digital, Dolby Digital Plus, Dolby PL II Movie, Dolby Surround, Dolby
TrueHD, Multichannel, DTS, DTS 96/24, DTS-HD High Resolution Audio, DTS-HD Master
Audio, DTS Neural:X, DTS Express and DSD.
0 It cannot be set if the listening mode is Pure Audio or Direct.
∫ Other
A/V Sync: If the video is behind the audio, you can delay the audio to offset the gap.
Different settings can be set for each input selector.
0 It cannot be set if the listening mode is Pure Audio or Direct.
Dialog Control: You can increase volume of the dialog portion of the audio in 1 dB steps up
to 6 dB so that you can make dialog easier to hear over background noise.
0 This cannot be set for content other than DTS:X.
0 The effect may not be selectable with some content.
We plan to provide support for the Dolby Atmos audio format through firmware updates for
this unit. This means that the settings available depend on the version of firmware.
On firmware version before Dolby Atmos support
0 Panorama, Dimension, and Center Width can be set.
On firmware versions supporting Dolby Atmos
0 Panorama, Dimension, and Center Width cannot be set after updating.
Music Optimizer: Improve the quality of the compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The setting can be separately set to each
input selector. The setting is effective in the signals of 48 kHz or less. The setting is not
effective in the bitstream signals.
0 It cannot be set if the listening mode is Pure Audio or Direct.
Late Night: Make small sounds easily heard. It is useful when you need to reduce the
volume while watching a movie late night. You can enjoy the effect only when playing Dolby
series and DTS series input signals.
0 The setting cannot be used in the following cases.
– When "3. Audio Adjust" - "Dolby" - "Loudness Management" (P57) in the Setup menu
is set to "Off" and Dolby Digital Plus or Dolby TrueHD is being played
– When the input signal is DTS:X and "Dialog Control" is other than 0 dB
Panorama: Broaden the sound field laterally when playing in the Dolby Pro Logic II Music
listening mode.
Dimension: Adjust the depth of the sound field in the front to back direction when playing in
the Dolby Pro Logic II Music listening mode. Set a small number to move the sound towards
the front. Set a large number to move the sound back.
Center Width: Adjust the width of the sound field of the front channel when playing in the
Dolby Pro Logic II Music listening mode. Set a small number to concentrate sound in the
middle. Set a large number to distribute the central sound out to the left and right.
En 67
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Web Setup
You can make the settings for network features for this unit in an internet browser on a PC,
smartphone, etc.
1. Press
on the remote controller to display the Setup menu.
2. Select "5. Hardware" - "Network" with the cursors, then take a note of the IP address
displayed in "IP Address".
3. Start the internet browser on your PC or smartphone and enter the IP address of the unit
in the URL field.
4. Information for the unit (Web Setup screen) is displayed in the internet browser.
5. After changing the settings, select "Save" to save the settings.
Device Information
You can change the Friendly Name, set an AirPlay Password, etc.
Control4: Register this unit if you are using a Control4 system.
Firmware Update: Select the firmware update you have downloaded to your PC so you can
update this unit.
Network Setting
Status: You can see information for the network such as the MAC address and IP address
for this unit.
Network Connection: You can select how to connect to the network. If you select "Wireless",
select an access point from "Wi-Fi Setup" to connect.
DHCP: You can change DHCP settings. If you select "Off", set "IP Address", "Subnet Mask",
"Gateway", and "DNS Server" manually.
Proxy: Display and set the URL for the proxy server.
68
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Firmware Update
The updating function on this unit
How to update
Updating the Firmware via Network
This unit has functionality to update the firmware (the
system software) over a network or by the USB port. This
enables us to make improvements to a variety of operations
and to add features.
There are two methods for updating the firmware: via
network and via USB. The update may take about 20
minutes to complete for either method: via network or via
USB. Furthermore, settings you have changed are
maintained regardless of the method used for update.
Note that when this unit is connected to a network, you may
see notifications about firmware updates on the display. To
execute updating, select "Update Now" with the cursors of
the remote controller and press ENTER. "Completed!" is
displayed when the update is complete.
0 For the latest information on updates, visit our website.
There is no need to update the firmware on this unit if
there is no update available.
0 Before updating, make sure that the speaker setup
microphone is not connected.
0 During an update, do not
– Disconnect and reconnect any cable, USB storage
device, speaker setup microphone or headphones, or
perform any operation on the component such as turn
off its power
– Accessing this unit from a PC or smartphone using an
application
0 Check that the unit is turned on, and the connection to
the Internet is secured.
0 Turn off the controller component (PC etc.) connected to
the network.
0 Stop any playing Internet radio, USB storage device, or
server content.
0 When "5. Hardware" - "HDMI" - "HDMI CEC" is set to
"On" in the Setup menu, set to "Off".
0 The description may differ from the on-screen display but
that will not change operations or functionality.
1. Switch the input on the TV to that assigned to the unit.
2. Press
on the remote controller.
Disclaimer: The program and accompanying online
documentation are furnished to you for use at your own
risk.
We will not be liable and you will have no remedy for
damages for any claim of any kind whatsoever concerning
your use of the program or the accompanying online
documentation, regardless of legal theory, and whether
arising in tort or contract.
In no event will we be liable to you or any third party for any
special, indirect, incidental, or consequential damages of
any kind, including, but not limited to, compensation,
reimbursement or damages on account of the loss of
present or prospective profits, loss of data, or for any other
reason whatsoever.
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Video Input
4. Source
4. Digital Audio Input
5. Hardware
5. Analog Audio Input
6. Miscellaneous
3. Select "6. Miscellaneous" - "Firmware Update" -"Update
via NET" with the cursors in order and press ENTER.
Setup
1. Input/Output Assign
1. Tuner
2. Speaker
2. Remote ID
3. Audio Adjust
3. Firmware Update
4. Source
4. Initial Setup
5. Hardware
5. Lock
6. Miscellaneous
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via NET" if there
is no firmware update.
4. Press ENTER with "Update" selected to start update.
En 69
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
0 During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of the unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0 "Completed!" is displayed when the update is
complete.
5. Press Í ON/STANDBY on the main unit to switch the
unit to standby. The process is completed and your
firmware is updated to the latest version.
0 Do not use Í on the remote controller.
If an Error Message is Displayed: When an error occurs,
"¢-¢¢Error!" is displayed on the display of the unit. ("¢"
represents an alphanumeric character.) Check the
following:
0 ¢-01, ¢-10: Cannot recognize Ethernet cable. Connect
the Ethernet cable properly.
0 ¢-02, ¢-03, ¢-04, ¢-05, ¢-06, ¢-11, ¢-13, ¢-14, ¢-16,
¢-17, ¢-18, ¢-20, ¢-21: Internet connection error.
Check the following:
– Whether the router is turned on
– Whether this unit and router are connected to the
network
Try to disconnect and then connect again the power to
the unit and router. This may solve the problem. If you
are still unable to connect to the Internet, the DNS server
or proxy server may be temporarily down. Check the
service status with your ISP provider.
0 Others: Disconnect then reconnect the power cord, then
repeat from the beginning.
0
0
0
0
0
0
0
1.
2.
3.
4.
Updating via USB
0 Prepare a 128MB or larger USB storage device. FAT16
or FAT32 file system format.
– Media inserted in a USB card reader may not be used
for this function.
– USB storage devices with security function are not
70
5.
6.
supported.
– USB hubs and USB devices with hub function are not
supported. Do not connect these devices to the unit.
Delete any data stored on the USB storage device.
Turn off the controller component (PC etc.) connected to
the network.
Stop any playing Internet radio, USB storage device, or
server content.
When "5. Hardware" - "HDMI" - "HDMI CEC" is set to
"On" in the Setup menu, set to "Off".
Some USB storage devices may take long to load, may
not be loaded correctly, or may not be correctly fed
depending on the device or their content.
We will not be liable whatsoever for any loss or damage
of data, or storage failure arising from the use of the USB
storage device with this AV receiver. Thank you for your
understanding.
The description may differ from the on-screen display but
that will not change the way to operate or the function.
Connect the USB storage device to your PC.
Download the firmware file from the our website to your
PC and unzip.
Firmware files are named in the following way:
ONKAVR¢¢¢¢_¢¢¢¢¢¢¢¢¢¢¢¢.zip
Unzip the file on your PC. The number of unzipped files
and folders varies depending on the model.
Copy all unzipped files and folders to the root folder of
the USB storage device.
0 Make sure to copy the unzipped files.
Connect the USB storage device to the USB port on the
main unit.
0 If you connect a USB hard disk drive to the USB port
of the unit, we recommend that you use its AC adapter
to power it.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
Switch the input on the TV to that assigned to the unit.
Press
on the remote controller.
Setup
1. Input/Output Assign
1. TV Out / OSD
2. Speaker
2. HDMI Input
3. Audio Adjust
3. Video Input
4. Source
4. Digital Audio Input
5. Hardware
5. Analog Audio Input
6. Miscellaneous
7. Select "6. Miscellaneous" - "Firmware Update" -"Update
via USB" with the cursors in order and press ENTER.
Setup
1. Input/Output Assign
1. Tuner
2. Speaker
2. Remote ID
3. Audio Adjust
3. Firmware Update
4. Source
4. Initial Setup
5. Hardware
5. Lock
6. Miscellaneous
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via USB" if there
is no firmware update.
8. Press ENTER with "Update" selected to start update.
0 During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of the unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0 During the update, do not turn off, or disconnect then
reconnect the USB storage device.
0 "Completed!" is displayed when the update is
complete.
9. Disconnect the USB storage device from the main unit.
10.Press Í ON/STANDBY on the main unit to switch the
unit to standby. The process is completed and your
firmware is updated to the latest version.
0 Do not use Í on the remote controller.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
If an Error Message is Displayed: When an error occurs,
"¢-¢¢ Error!" is displayed on the display of the unit. ("¢"
represents an alphanumeric character.) Check the
following:
0 ¢-01, ¢-10: USB storage device not found. Check
whether the USB storage device or USB cable is
correctly inserted to the USB port of this unit.
Connect the USB storage device to an external power
source if it has its own power supply.
0 ¢-05, ¢-13, ¢-20, ¢-21: The firmware file is not present
in the root folder of the USB storage device, or the
firmware file is for another model. Retry from the
download of the firmware file.
0 Others: Disconnect then reconnect the power cord, then
repeat from the beginning.
En 71
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Supplementary Information
Supplementary Information
Due to firmware (the software for the system) updates after
you make your purchase or firmware changes during
production of the product, there may be additions or
changes to the settings and operation available compared
to what is in the instruction manual.
For information about the settings and operations that have
been added or changed, see the following references.
Refer to "Supplementary information for player functions"
(P34) for information about changes to player functions.
Supplementary Information
>>> Click here <<<
72
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Troubleshooting
Others
Before starting the procedure
Problems may be solved by simply turning the power on/off
or disconnecting/connecting the power cord, which is easier
than working on the connection, setting and operating
procedure. Try the simple measures on both the unit and
the connected device. If the problem is that the video or
audio is not output or the HDMI linked operation does not
work, disconnecting/connecting the HDMI cable may solve
it. Turn off the device connected to this unit, then
disconnect and reconnect the cable. When reconnecting,
be careful not to wind the HDMI cable since if wound the
HDMI cable may not fit well.
0 The AV receiver contains a microPC for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least 5 seconds, and then plug it back
in.
0 We are not responsible for reparations for damages
(such as CD rental fees) due to unsuccessful recordings
caused by the unit’s malfunction. Before you record
important data, make sure that the material will be
recorded correctly.
If operation becomes unstable
Try restarting the unit
The issue may be fixed by restarting this unit. After
switching this unit to standby, press and hold Í ON/
STANDBY on this unit for 5 or more seconds to restart the
unit. (The settings in the unit are maintained.) If the issue is
not fixed by restarting, try unplugging the power cords of
the unit and connected devices, and then plugging them in
again.
Resetting the unit (this resets the unit settings to the
default)
If restarting the unit doesn't fix the problem, resetting the
unit to the status at the time of shipment may solve the
problem. Your settings will also be initialized when you
reset, so note down your settings before doing the
following.
1. While holding down CBL/SAT on the main unit, press
Í ON/STANDBY.
2. The unit switches to standby and the settings are reset.
To reset the remote control, while holding down MODE,
press
until the remote indicator flashes twice (3
seconds or more).
∫ Power
Cannot turn on the unit
0 Make sure that the power cord is properly plugged into
the wall outlet.
0 Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The unit turns off unexpectedly
0 The unit automatically switches to standby when the "5.
Hardware" - "Power Management" - "Auto Standby"
setting in the Setup menu functions.
0 The protective circuit function may have been activated.
If this has occurred, "AMP Diag Mode" appears on the
display when the unit is turned on again, and the unit
enters diagnostic mode. If the results of the diagnosis is
that there is no problem, the "AMP Diag Mode" display
disappears and you can use the unit normally again. If
“CHECK SP WIRE” appears on the display, the speaker
cables may be short-circuited. Make sure bare speaker
wires are not touching each other or the back panel of
the unit, then turn the unit on again. If "NG" is displayed,
immediately unplug the power cord from the wall outlet
and contact your dealer.
0 The protective circuit function may have been activated
because the temperature of the unit rose abnormally. If
this happens, then the power will continue to turn off after
you have turned the unit on again. Make sure the unit
has plenty of space for ventilation around it, wait for the
unit to cool down sufficiently, and then try turning it on
again.
WARNING: If smoke, smell or abnormal noise is produced
by the unit, unplug the power cord from the wall outlet
immediately and contact the dealer or customer support.
∫ Audio
0 Make sure that the speaker setup microphone is not still
connected.
En 73
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 If the MUTE indicator on the display flashes, press
on
the remote controller to cancel muting.
0 While headphones are connected to the PHONES jack,
no sound is output from the speakers.
0 When "4. Source" - "Audio Select" - "PCM Fixed Mode"
in the Setup menu is set to "On", no sound is played
when signals other than PCM are input. Change the
setting to "Off".
Check the following if the above does not fix the problem:
There is no sound from the TV
0 Change the input selector on this unit to the position of
the terminal to which the TV is connected.
0 If the TV doesn't support the ARC function, along with
connection by HDMI, connect the TV and this unit using
a digital optical cable, digital coaxial cable, or analog
audio cable.
No sound from a connected player
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
0 Check the digital audio output setting on the connected
component. On some game consoles, such as those that
support DVD, the default setting is off.
0 With some DVD-Video discs, you need to select an audio
output format from a menu.
A speaker produces no sound
0 Make sure that the polarity of the speaker cables (+/-) is
correct, and that no bare wires are in contact with the
metal part of speaker terminals.
0 Make sure that the speaker cables have not shorted.
0 Make sure the speakers are connected correctly (P14).
Settings for the speaker connection environment need to
be made in "1. AccuEQ Room Calibration" (P20) in Initial
74
Setup.
0 Depending on the source and current listening mode, not
much sound may be produced. Select another listening
mode to see if sound is output.
The subwoofer produces no sound
If the setting of the front speakers is "Full Band" and during
2ch input such as from the TV or music, the low range
elements will be output from the front speakers rather than
from the subwoofer. If you would rather output from the
subwoofer, make one of the following settings.
1. Change the front speakers settings to a setting other
than "Full Band" for the crossover frequency value.
The range below the frequency you specify will be output
from the subwoofer rather than the front speakers. We
do not recommend changing this if your front speakers
have good low range reproduction capabilities.
2. Change "Double Bass" to "On".
The low range elements will be output from both the front
speakers and the subwoofer. This may mean that there
is too much bass. Do not change if this happens, or
choose option 1.
0 Refer to "2. Speaker" - "Crossover" (P55) in the Setup
menu for details.
0 When you play source material that contains no
information in the LFE channel, the subwoofer produces
no sound.
Noise can be heard
0 Using cable ties to bundle analog audio cables, power
cords, speaker cables, etc. may degrade the audio
performance, so refrain from doing it.
0 An audio cable may be picking up interference. Try
repositioning your cables.
The beginning of audio received by an HDMI IN cannot
be heard
0 Since it takes longer to identify the format of an HDMI
signal than it does for other digital audio signals, audio
output may not start immediately.
Sound suddenly reduces
0 When the temperature inside the unit exceeds a certain
temperature for extended periods, the volume may be
reduced automatically to protect the circuits.
∫ Listening mode
0 To enjoy digital surround playback, such as Dolby Digital,
the audio signals need to pass through a connection via
HDMI cable, digital coaxial cable, or digital optical cable.
Audio output should be also set to bitstream output on
the connected Blu-ray disc player or other device.
0 Press
on the remote controller several times to switch
the display of the main unit to check the input format.
Check the following if the above does not fix the problem:
Cannot select a desired listening mode
0 Depending on the connecting status of the speaker,
some listening modes may not be selected (P38).
There is no sound with Dolby TrueHD, Dolby Atmos,
DTS-HD Master Audio, or DTS:X
0 If you cannot output formats such as Dolby TrueHD,
Dolby Atmos, DTS-HD Master Audio, or DTS:X
according to the format of the source, in the Blu-ray Disc
player settings try setting "BD video supplementary
sound" (or re-encode, secondary sound, video additional
audio, etc.) to "Off". Change the listening mode for each
source after changing the setting to confirm.
0 We plan to provide support for the Dolby Atmos audio
format through firmware updates for this unit.
About DTS signals
0 With media that switches suddenly from DTS to PCM,
PCM playback may not start immediately. In such cases,
you should stop your player for about 3 seconds and
then resume playback.
0 With some CD and LD players, you will not be able to
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
playback DTS material properly even though your player
is digitally connected to this unit. This is usually because
the DTS signal has been processed (e.g., output level,
sampling rate, or frequency response changed) and the
unit does not recognize it as a genuine DTS signal. In
such cases, you may hear noise.
0 When playing DTS program material, if you use
operations such as pause or skip on your player, you
may notice a short audible noise. This is not a
malfunction.
∫ Video
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 There may be interference from the power cords or other
connection cables to this unit if the picture on the TV is
poor. Try separating the TV antenna cable and other
cables of the unit.
0 Check the screen input on the monitor, such as the TV.
Check the following if the above does not fix the problem:
There is no video
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
0 While the Pure Audio listening mode is selected, the
analog video circuitry is turned off and only video signals
input through HDMI input jacks can be output.
There is no picture from a source connected to an
HDMI IN terminal.
0 To display video from the connected player on the TV
screen while the unit is in standby, you need to enable "5.
Hardware"- "HDMI" - "HDMI Standby Through" in the
Setup menu. Refer to (P60) for information about HDMI
Standby Through.
0 Check if "Resolution Error" is displayed on the main unit
display when video input via HDMI IN jack is not
displayed. In this case, the TV does not support the
resolution of the video input from the player. Change the
setting on the player.
0 Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
supported.
0 Concrete walls weaken radio signals.
0 Listen to the station in mono.
0 When listening to an AM station, operating the remote
controller may cause noise.
0 FM reception may become clearer if you use the antenna
jack on the wall used for the TV.
Images flicker
0 It is possible that the resolution of the player is not
compatible with the TV's resolution. If you have
connected the player to this unit with an HDMI cable, try
changing the output resolution on the player. There also
may be an improvement if you change the screen mode
on the TV.
∫ The BLUETOOTH feature
Video and audio are out of sync
0 Video may be delayed relative to audio depending on the
settings and connections with your TV. To adjust, press
Q on the remote controller, and adjust in "Other" - "A/V
Sync" in "Quick Menu".
∫ Linked operation
There is no linked operation with CEC compliant
devices, such as a TV.
0 The "5. Hardware" - "HDMI" - "HDMI CEC" setting in the
Setup menu needs to be set to "On".
0 It is also necessary to set HDMI linking on the CEC
compliant device. Check the instruction manual.
∫ Tuner
Radio reception is poor or there is a lot of noise.
0 Re-check the antenna connection.
0 Separate the antenna from speaker cables and the
power cord.
0 Move the unit away from your TV or PC.
0 Passing cars and airplanes can cause interference.
0 Try plugging/unplugging the power of the unit and try
turning on/off the BLUETOOTH wireless technology
enabled device. Restarting the BLUETOOTH wireless
technology enabled device may be effective.
0 The BLUETOOTH wireless technology enabled devices
must support the A2DP profile.
0 Radio wave interference may occur in the vicinity of
components, such as microwave ovens or cordless
phones, which use radio waves in the 2.4 GHz range.
This interference may render this unit unusable.
0 If there is a metallic object near the unit, BLUETOOTH
connection may not be possible as the metal can effect
on the radio waves.
Check the following if the above does not fix the problem:
Cannot connect with this unit
0 Check that the BLUETOOTH function of the
BLUETOOTH wireless technology enabled device is
enabled.
Music playback is unavailable on the unit even after
successful BLUETOOTH connection
0 When the audio volume of your BLUETOOTH wireless
technology enabled device is set low, the playback of
audio may be unavailable. Turn up the volume on the
BLUETOOTH wireless technology enabled device.
0 Some BLUETOOTH wireless technology enabled
devices may be equipped with a Send/Receive selector
switch. Select Send mode.
0 Depending on the characteristics or specifications of
En 75
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
your BLUETOOTH wireless technology enabled device,
playback on this unit may not be possible.
Sound is interrupted
0 There may be a problem with the BLUETOOTH wireless
technology enabled device. Check the information on the
Internet.
The audio quality is poor after connection with a
BLUETOOTH wireless technology enabled device
0 The BLUETOOTH reception is poor. Move the
BLUETOOTH wireless technology enabled device closer
to the unit or remove any obstacle between the
BLUETOOTH wireless technology enabled device and
this unit.
∫ Network Functions
0 If you cannot select a network service, it will become
selectable when the network function is started. It may
take about a minute to start up.
0 When NET is blinking, the AV receiver is not properly
connected to the home network.
0 Try plugging/unplugging the power supply of this unit and
the router, and try rebooting the router.
0 If the desired wireless LAN router is not in the access
point list, it may be set to hide SSID or the ANY
connection may be off. Change the setting and try again.
Check the following if the above does not fix the problem:
Cannot access the Internet radio
0 Certain network service or contents available through the
unit may not be accessible in case the service provider
terminates its service.
0 Make sure that your modem and router are properly
connected, and make sure they are both turned on.
0 Make sure that the LAN side port on the router is
properly connected to the AV receiver.
0 Make sure that connecting to Internet from other
76
components is possible. If connecting is not possible,
turn off all components connected to the network, wait for
a while, and then turn on the components again.
0 If a specific radio station is unavailable for listening,
make sure the registered URL is correct, or whether the
format distributed from the radio station is supported by
the AV receiver.
0 Depending on ISP, setting the proxy server is necessary.
0 Make sure that the router and/or modem you are using is
supported by your ISP.
Cannot access the network server
0 This unit needs to be connected to the same router as
the network server.
0 This unit is compatible with Windows Media® Player 11
or 12 network servers or NAS that are compatible with
home network functionality.
0 You may need to make some settings on Windows
Media® Player (P32).
0 When using a PC, only music files registered in the
Windows Media® Player library can be played.
Playback stops while listening to music files on the
network server
0 Make sure the network server is compatible with this unit.
0 When the PC is serving as the network server, try
quitting any application software other than the server
software (Windows Media® Player 12 etc.).
0 If the PC is downloading or copying large files, the
playback may be interrupted.
∫ USB storage device
USB storage device is not displayed
0 Check whether the USB storage device or USB cable is
correctly inserted to the USB port of the unit.
0 Disconnect the USB storage device from the unit, and
then try reconnecting.
0 Performance of hard disks that receive power from the
USB port of the unit is not guaranteed.
0 Depending on the type of format, the playback may not
be performed normally. Check the type of the file formats
that is supported.
0 USB storage devices with security functions may not be
played.
∫ Wireless LAN Network
0 Try plugging/unplugging the power supply of wireless
LAN router and the unit, check the wireless LAN router
power-on status, and try reboot of the wireless LAN
router.
Check the following if the above does not fix the problem:
Cannot access wireless LAN network
0 The wireless LAN router setting may be switched to
Manual. Return the setting to Auto.
0 Try the manual set-up. The connection may succeed.
0 When the wireless LAN router setting is at stealth mode
(mode to hide the SSID key) or when ANY connection is
off, the SSID is not displayed. Change the setting and try
again.
0 Check that the setting of SSID and encryption (WEP,
etc.) is correct. Make sure the network settings of the unit
is properly set.
0 Connection to an SSID that includes multi-byte
characters is not supported. Name the SSID of the
wireless LAN router using single-byte alphanumeric
characters only and try again.
Connected to an SSID different to the SSID selected
0 Some wireless LAN routers allow you to set multiple
SSIDs for one unit. If you use the automatic setting
button on such a router, you may end up connecting with
a different SSID from the SSID you wanted to connect to.
Use the connection method requiring you to enter a
password if this happens.
Playback is interrupted and communication does not
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
work
0 You may not receive radio waves due to bad radio wave
conditions. Shorten the distance from the wireless LAN
router or remove obstacles to improve visibility, and try
again. Place the unit away from microwave ovens or
other access points. It is recommended to place the
wireless LAN router and the unit in the same room.
0 If there is a metallic object near the unit, wireless LAN
connection may not be possible as the metal can effect
on the radio wave.
0 When other wireless LAN devices are used near the unit,
several issues such as interrupted playback and
communication may occur. You can avoid these issues
by changing the channel of your wireless LAN router. For
instructions on changing channels, see the instruction
manual provided with your wireless LAN router.
0 There may not be enough bandwidth available in the
band for wireless LAN. Connect using an Ethernet cable.
∫ Remote Controller
0 Make sure that the batteries are installed with the correct
polarity.
0 Install new batteries. Do not mix different types of
batteries, or old and new batteries.
0 Make sure that the unit is not subjected to direct
sunshine or inverter-type fluorescent lights. Relocate if
necessary.
0 If the unit is installed in a rack or cabinet with coloredglass doors or if the doors are closed, the remote
controller may not work reliably.
mode is selected.
∫ Others
Strange noises can be heard from the unit
0 If you have connected another unit to the same wall
outlet as this unit, this noise may be an effect from the
other unit. If the symptoms improve by unplugging the
power cord of the other unit, use different wall outlets for
this unit and the other unit.
The message "Noise Error" is displayed during
AccuEQ Room Calibration
0 This can be caused by a malfunction in your speaker
unit. Check if the speakers produce normal sounds.
The results of AccuEQ Room Calibration give a
different distance to the speakers than the actual
distance
0 There may be some discrepancies in the results
depending on the speakers you are using. If this is the
case, make the settings in "2. Speaker" - "Distance" in
the Setup menu.
∫ Display
The display doesn't light
0 The display may go dim while the Dimmer is working.
Press DIMMER to change the brightness level of the
display.
0 The display is turned off when the Pure Audio listening
En 77
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
General Specifications
Amplifier (Audio) section
Rated Output Power (IEC)
5 ch k 135 W at 6 ohms, 1 kHz, 1 ch driven of 1% THD
Maximum Effective Output Power (JEITA) (Australian)
5 ch k 160 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD
Dynamic Power (*)
(*)IEC60268-Short-term maximum output power
160 W (3 ≠, Front)
125 W (4 ≠, Front)
85 W (8 ≠, Front)
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20,000 Hz, half power)
Input Sensitivity and Impedance (1 kHz, 100 W/8 ≠)
200 mV/47 k≠ (LINE (Unbalance))
Rated RCA Output Level and Impedance
1 V/470 ≠ (SUBWOOFER PRE OUT)
Frequency Response
10 Hz - 100 kHz/i1 dB, j3 dB (Direct/Pure Audio)
Tone Control Characteristics
n10 dB, 90 Hz (BASS)
n10 dB, 7.5 kHz (TREBLE)
Signal to Noise Ratio
106 dB (IHF-A, LINE IN, SP OUT)
Speaker Impedance
4 ≠ - 16 ≠
Headphone Output Impedance
330 ≠
Headphone Rated Output
80 mW (32 ≠, 1 kHz, 10% THD)
Video Section
Signal level
1 Vp-p/75 ≠ (Composite Video)
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 108.0 MHz, RDS
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
78
Preset Channel
40
Network Section
Ethernet LAN
10BASE-T/100BASE-TX
Wireless LAN
IEEE 802.11 a/b/g/n standard
(Wi-Fi® standard)
5 GHz/2.4 GHz band
BLUETOOTH Section
Communication system
BLUETOOTH Specification version 4.1+LE
Frequency band
2.4 GHz band
Modulation method
FHSS (Frequency Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
A2DP 1.2
AVRCP 1.3
HOGP-Host (Client)
HOGP-HID Device (Server)
HID Service (HIDS)
Supported Codecs
SBC
AAC
Transmission range (A2DP)
20 Hz - 20 kHz (Sampling frequency 44.1 kHz)
Maximum communication range
Line of sight approx. 15 m (*)
(*)The actual range will vary depending on factors such as
obstacles between devices, magnetic fields around a
microwave oven, static electricity, cordless phone,
reception sensitivity, antenna’s performance, operating
system, software application, etc.
General
Power Supply
AC 220 - 240 V, 50/60 Hz
Power Consumption
400 W
0.15 W (Stand-by)
40 W (No-sound)
4.5 W (HDMI Standby Through)
2.8 W (Network Standby)
Dimensions (W k H k D)
435 mm k 160 mm k 328 mm
Weight
8.6 kg
HDMI
Input
IN1 (BD/DVD), IN2 (CBL/SAT), IN3 (STRM BOX), IN4
(GAME)
Output
OUT (HDCP2.2)
Supported
Deep Color, x.v.ColorTM, LipSync, Audio Return
Channel, 3D, 4K 60Hz, CEC, Extended Colorimetry
(sYCC601, Adobe RGB, Adobe YCC601), Content Type,
HDR
Audio Format
Dolby Atmos (to be supported in a future update), Dolby
TrueHD, Dolby Digital, Dolby Digital Plus, DTS, DTS:X,
DTS-HD Master Audio, DTS-HD High Resolution Audio,
DTS 96/24, DTS-HD Express, DSD, PCM
Maximum Video Resolution
4k 60 Hz (YCbCr 4:4:4)
Video Inputs
Composite
IN1 (GAME), IN2 (CBL/SAT)
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Compatible input resolutions
HDMI input
4K, 1080p/24, 1080p, 1080i, 720p, 480p/576p
Composite input
480i/576i
0 The output from the HDMI OUT jack to the TV is the
same resolution as the input.
Audio Inputs
Digital
OPTICAL IN1 (CD), IN2 (TV)
COAXIAL IN (CBL/SAT)
Analog
IN1 (GAME), IN2 (PC), IN3 (CD), AUX (Front, Ø 3.5 mm)
Audio Outputs
Analog
SUBWOOFER PRE OUT
Speaker Outputs
FRONT L/R, CENTER, SURROUND or HEIGHT L/R
Phones
PHONES (Front, Ø 6.3 mm)
Others
USB: 1 (Rear, Ver.2.0, 5 V/1 A)
Ethernet: 1
Setup Mic: 1 (Front)
Power consumption in standby mode
In the following cases, the power consumption in standby
mode may reach up to a maximum of 12 W:
– When "Network Standby" is set to "On"
– When "HDMI CEC" is set to "On"
– When "HDMI Standby Through" is set to other than "Off"
– When "Bluetooth Wakeup" is set to "On"
– When "USB Power Out at Standby" is set to "On"
En 79
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
Reference Information
About HDMI
input the audio from the TV to this unit.
Copyright protection technology: HDCP1.4/HDCP2.2
Compatible functions
HDMI Standby Through: Even if this unit is in standby, the
input signals from AV components are transmitted to the
TV.
x.v.ColorTM: This technology realizes even more realistic
colors by broadening the color gamut.
Color Depth: 720k480i 60Hz, 720k576i 50Hz, 720k480p
60Hz, 720k576p 50Hz, 1920k1080i 50/60Hz, 1280k720p
24/25/30/50/60Hz, 1680k720p 24/25/30/50/60Hz,
1920k1080p 24/25/30/50/60Hz, 2560k1080p 24/25/30/50/
60Hz, 4K (3840k2160p) 24/25/30Hz, 4K SMPTE
(4096k2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8/10/12 bit),
YCbCr4:2:2 (12 bit)
4K (3840k2160p) 50/60Hz, 4K SMPTE (4096k2160p) 50/
60Hz : RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit),
YCbCr4:2:0 (8/10/12 bit)
3D: You can transmit 3D video signals from AV components
to the TV.
Supported Audio Formats
HDMI (High Definition Multimedia Interface) is a digital
interface standard for connecting TVs, projectors, Blu-ray
Disc/DVD players, set-top boxes, and other video
components. Until now, several separate video and audio
cables have been required to connect AV components.
With HDMI, a single cable can carry control signals, digital
video, and digital audio (2-channel PCM, multichannel
digital audio, and multichannel PCM).
HDMI CEC feature: By connecting devices and HDMI
cables that comply with the CEC (Consumer Electronics
Control) specification of the HDMI standard, a variety of
linked operation become possible between devices. You
can enjoy features such as linking input switching with input
and players, control volume using the remote controller of
the TV, and automatically switching this unit to standby
when the TV is turned off. The unit is designed to link with
products that comply with the CEC standard, and that
linked operation is not always guaranteed with all CEC
devices. For linked functions to work properly, do not
connect more CEC-compliant components than the
quantities specified below, to the HDMI jack.
0 Blu-ray Disc/DVD players: up to 3 units.
0 Blu-ray Disc/DVD recorders: up to 3 units.
0 Cable TV tuner, terrestrial digital tuner, and satellite
broadcasting tuner: up to 4 units.
Operation has been confirmed on the following devices: (As
of April 2017)
Toshiba brand televisions; Sharp brand televisions; Onkyo
and Integra brand RIHD-compatible players; Toshiba brand
players and recorders; Sharp brand players and recorders
(when used with a Sharp brand television)
ARC (Audio Return Channel): By connecting a TV that
supports ARC with a single HDMI cable, you can not only
output the audio and video from this unit to the TV, but also
80
Deep Color: By connecting devices supporting Deep Color,
video signals input from the devices can be reproduced on
the TV with even more colors.
4K: This unit supports 4K (3840k2160p) and 4K SMPTE
(4096k2160p) video signals.
LipSync: This setting automatically corrects any
desynchronization between the video and audio signals
based on data from the HDMI Lip-Sync compatible TV.
Supported Audio Formats
2-channel linear PCM: 32 kHz, 44.1 kHz, 48 kHz, 88.2
kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit
Multi-channel linear PCM: Maximum 5.1 channels, 32
kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192
kHz, 16/20/24 bit
Bitstream: Dolby Atmos (to be supported in a future
update), Dolby Digital, Dolby Digital Plus, Dolby TrueHD,
DTS, DTS:X, DTS-HD High Resolution Audio, DTS-HD
Master Audio
DSD: Supported sampling rates: 2.8 MHz
Your Blu-ray Disc/DVD player must also support HDMI
output of the above audio formats.
Supported resolutions
USB Storage
This unit supports the following music file formats. Note that
sound files that are protected by copyright cannot be played
on this unit.
MP3 (.mp3/.MP3):
0 Supported formats: MPEG-1/MPEG-2 Audio Layer 3
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR
WMA (.wma/.WMA):
0 Supported sampling rates: 44.1 kHz and 48 kHz
0 Supported bitrates: Between 5 kbps and 320 kbps and
VBR
0 WMA Pro/Voice/WMA Lossless formats are not
supported
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
AIFF (.aiff/.aif/.AIFF/.AIF):
AIFF files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/
.3G2):
0 Supported formats: MPEG-2/MPEG-4 Audio
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR
FLAC (.flac/.FLAC):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
0 Supported formats: DSF/DSDIFF
0 Supported sampling rates: 2.8 MHz and 5.6 MHz
Dolby TrueHD (.vr/.mlp/.VR/.MLP):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Variable bit-rate (VBR) files are supported. However,
playback times may not be displayed correctly.
0 This unit supports the gapless playback of the USB
storage device in the following conditions.
When playing WAV, FLAC and Apple Lossless, and the
same format, sampling frequency, channels and
quantization bit rate are played continuously
Music Server
This unit supports the following music file formats. Remote
play of FLAC, DSD, and Dolby TrueHD is not supported.
MP3 (.mp3/.MP3):
0 Supported formats: MPEG-1/MPEG-2 Audio Layer 3
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR
WMA (.wma/.WMA):
0 Supported sampling rates: 44.1 kHz, 48 kHz
0 Supported bitrates: Between 5 kbps and 320 kbps and
VBR
0 WMA Pro/Voice/WMA Lossless formats are not
supported
WAV (.wav/.WAV):
WAV files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AIFF (.aiff/.aif/.AIFF/.AIF):
AIFF files include uncompressed PCM digital audio.
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/.3GP/
.3G2):
0 Supported formats: MPEG-2/MPEG-4 Audio
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz
0 Supported bitrates: Between 8 kbps and 320 kbps and
VBR
FLAC (.flac/.FLAC):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, 192 kHz
0 Quantization bit: 8 bit, 16 bit, 24 bit
LPCM (Linear PCM):
0 Supported sampling rates: 44.1 kHz and 48 kHz
0 Quantization bit: 16 bit
Apple Lossless (.m4a/.mp4/.M4A/.MP4):
0 Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz
0 Quantization bit: 16 bit, 24 bit
DSD (.dsf/.dff/.DSF/.DFF):
0 Supported formats: DSF/DSDIFF
0 Supported sampling rates: 2.8 MHz, 5.6 MHz
0 Variable bit-rate (VBR) files are supported. However,
playback times may not be displayed correctly.
0 Remote playback does not support the gapless
playback.
Device Requirements
USB Storage
0 Note that operation is not guaranteed with all USB
storage devices.
0 This unit can use USB storage devices that comply with
the USB mass storage device class standard. The unit is
also compatible with USB storage devices using the
FAT16 or FAT32 file system formats.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
0 Up to 20,000 tracks per folder can be displayed, and
folders may be nested up to 16 levels deep.
0 USB hubs and USB storage devices with hub functions
are not supported. Do not connect these devices to the
unit.
0 USB storage devices with security function are not
supported on this unit.
0 If you connect a USB hard disk drive to the USB port of
the unit, we recommend that you use its AC adapter to
power it.
0 Media inserted to the USB card reader may not be
En 81
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
available in this function. Furthermore, depending on the
USB storage device, proper reading of the contents may
not be possible.
0 We accepts no responsibility whatsoever for the loss or
damage to data stored on a USB storage device when
that device is used with this unit. We recommend that
you back up your important music files beforehand.
82
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Advanced Setup | Supplementary Information | Others
License and Trademark
PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks
or registered trademarks of Pandora Media, Inc. Used with permission.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Pro
Logic, Dolby Surround, Dolby Vision and the double-D symbol are trademarks
of Dolby Laboratories.
The BLUETOOTH® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc.
The Spotify software is subject to third party licenses found here:
https://developer.spotify.com/esdk-third-party-licenses/
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, DTS:X, and
the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the
United States and/or other countries. © DTS, Inc. All Rights Reserved.
®
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi Alliance®.
AirPlay, iPad, iPhone, iPod, iPod classic, iPod nano and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other countries.
This product is protected by certain intellectual property rights of Microsoft. Use
or distribution of such technology outside of this product is prohibited without a
license from Microsoft.
Windows 7, Windows Media, and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation in the United States and/or
other countries.
"x.v.Color" and "x.v.Color" logo are trademarks of Sony Corporation.
DSD and the Direct Stream Digital logo are trademarks of Sony Corporation.
"Theater-Dimensional" and "Theater-Dimensional (logo)" are trademarks of
Onkyo Corporation.
All other trademarks are the property of their respective owners. / Toutes les
autres marques commerciales sont la propriété de leurs détenteurs respectifs. /
El resto de marcas comerciales son propiedad de sus respectivos propietarios.
/ Tutti gli altri marchi di fabbrica sono di proprietà dei rispettivi proprietari. / Alle
anderen Warenzeichen sind das Eigentum ihrer jeweiligen Eigentümer. / Alle
andere handelsmerken zijn eigendom van de desbetreffende rechthebbenden.
/ Alla andra varumärken tillhör deras respektive ägare. / Kaikki muut tuotemerkit
ovat omistajiensa omaisuutta. / 所有其他商標為各自所有者所有。
iPad Air and iPad mini are trademarks of Apple Inc.
"Made for iPod", "Made for iPhone" and "Made for iPad" mean that an
electronic accessory has been designed to connect specifically to iPod, iPhone,
or iPad, respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone or iPad may affect
wireless performance.
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac
with OS X Mountain Lion or later, and PC with iTunes 10.2.2 or later.
En 83
1-10-5 Yokoami, Sumida-ku, Tokyo 130-0015 JAPAN
http://www.onkyo.com/
<U.S.A.>
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
http://www.us.onkyo.com/
<Germany>
Gutenbergstrasse 3, 82178 Puchheim, Germany
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
<UK>
Anteros Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex,
HA4 6QQ United Kingdom
Tel: +44 (0)871-200-1996 Fax: +44 (0)871-200-1995
For Product Support only: +44 (0)208-836-3510
http://www.uk.onkyo.com/en/
<Hong Kong>
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: +852-2429-3118 Fax: +852-2428-9039
http://www.hk.onkyo.com/
<PRC>
302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032,
Tel: +86-21-52131366 Fax: +86-21-52130396
http://www.cn.onkyo.com/
<Asia, Oceania, Middle East, Africa>
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
<France>
6, Avenue de Marais F - 95816 Argenteuil Cedex FRANCE
For Product Support only: +33 969 368 138
http://www.fr.onkyo.com/fr/
F1711-1
(C) Copyright 2017 Onkyo & Pioneer Corporation Japan. All rights reserved.
SN 29402944A
http://www.onkyo.com/privacy/
* 2 9 4 0 2 9 4 4 A *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising