ONKYO | C-755 | Owner Manual | ONKYO C-755 User manual

ONKYO C-755 User manual
SN29402439_C-755_En.book
1 ページ
2016年8月9日
火曜日
午後2時14分
COMPACT DISC PLAYER
C-755
Getting Started ............................En-2
Connections .............................. En-13
Instruction Manual
Basic Operation ....................... En-15
Disc Playback ........................... En-16
Various Playback Modes ..... En-21
Setting for MP3 ........................ En-24
Thank you for purchasing an Onkyo product. Please read
this manual carefully before making any connections or
using this product. By following these instructions, you’ll get
the best audio performance and the most listening pleasure
from your Onkyo product. Keep this manual for future
reference.
Troubleshooting ...................... En-26
Specifications ........................... En-27
En
SN29402439_C-755_En.book
2 ページ
2016年8月9日
火曜日
午後2時14分
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
PORTABLE CART WARNING
12. Use only with the cart,
stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is
used, use caution when
moving the cart/apparatus
combination to avoid injury S3125A
from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
En-2
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have
fallen into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in any way, and
F. When the apparatus exhibits a distinct
change in performance this indicates a need
for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock.
The apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases shall be placed on the apparatus.
Don’t put candles or other burning objects on
top of this unit.
17. Batteries
Always consider the environmental issues and
follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that
there is adequate ventilation.
Leave 20 cm (8") of free space at the top and
sides and 10 cm (4") at the rear. The rear edge
of the shelf or board above the apparatus shall
be set 10 cm (4") away from the rear panel or
wall, creating a flue-like gap for warm air to
escape.
SN29402439_C-755_En.book
3 ページ
2016年8月9日
火曜日
午後2時14分
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal
without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
the dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 220-240 V, 50/60 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
5.
6.
7.
8.
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from
the mains. If you do not intend to use the unit
for an extended period, remove the power cord
from the AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat as sunshine, fire or the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by the dealer from
whom you purchased this unit.
Handling Notes
• If you need to transport this unit, use the
original packaging to pack it how it was when
you originally bought it.
• Do not leave rubber or plastic items on this
unit for a long time, because they may leave
marks on the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it
may not work properly the next time you turn
it on, so be sure to use it occasionally.
• When you’ve finished using this unit, remove
all discs and turn off the power.
9. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on
its side or on a sloping surface, because it
may cause a malfunction.
• If you install this unit near a TV, radio, or
VCR, the picture and sound quality may be
affected. If this occurs, move this unit away
from the TV, radio, or VCR.
10. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical pickup, one of the most important parts
inside this unit.
• Moisture condensation can occur in the following situations:
– The unit is moved from a cold place to a
warm place.
– A heater is turned on, or cold air from an
air conditioner is hitting the unit.
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility of moisture condensation occurring. Doing
so may damage your discs and certain parts
inside this unit.
If condensation does occur, unplug the power
cord and leave the unit for two to three hours in
the room temperature.
This unit contains a semiconductor laser system and
is classified as a “CLASS 1 LASER PRODUCT”. So,
to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact
the store where you purchased the unit.
To prevent being exposed to the laser beam, do
not try to open the enclosure.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
En-3
SN29402439_C-755_En.book
4 ページ
2016年8月9日
火曜日
午後2時14分
Precautions-Continued
The label on the right is
applied on the rear panel.
1. This unit is a CLASS 1
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove
the cover. Refer servicing to qualified personnel.
For British models
Replacement and mounting of an AC plug on the
power supply cord of this unit should be performed
only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the
fuse needs to be replaced, the replacement fuse
must approved by ASTA or BSI to BS1362 and
have the same ampere rating as that indicated on
the plug. Check for the ASTA mark or the BSI mark
on the body of the fuse.
If the power cord’s plug is not suitable for your
socket outlets, cut it off and fit a suitable plug. Fit a
suitable fuse in the plug.
For European Models
We declare, under our sole responsibility, that this
product complies with the standards:
– Safety
– Limits and methods of measurement of radio
disturbance characteristics
– Limits for harmonic current emissions
– Limitation of voltage changes, voltage fluctuations and flicker
– RoHS Directive, 2011/65/EU
WEEE
http://www.onkyo.com/manual/weee/weee.pdf
En-4
SN29402439_C-755_En.book
5 ページ
2016年8月9日
火曜日
午後2時14分
Supplied Accessories
Features
Make sure you have the following accessories
•
•
•
•
•
•
•
•
•
DIMMER
DISPLA
Y
RANDOM
REPEAT
ENTER
SETUP
SEARC
H
1
4
RC-822
2
8
0
MEMOR
Y
3
5
7
>10
6
9
CLEAR
C
Remote controller RC-822C and two batteries
(R03/AAA)
Batteries are not supplied with products for China.
24bit 192kHz D/A converter
VLSC*1 (Vector Linear Shaping Circuitry)
MP3 playback
25-track memory playback
RI-Compatible Remote Control
Auto standby
Coaxial digital audio output
Random playback
Random repeat playback
*1 VLSC and the VLSC logo are registered trademarks of
Onkyo Corporation.
Coaxial cable
cable (80 cm)
• To use , the CD Player must be connected with
a
cable.
Power cord
* In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications
and operations are the same regardless of color.
En-5
SN29402439_C-755_En.book
6 ページ
2016年8月9日
火曜日
午後2時14分
Contents
Important Safety Instructions ........................... 2
Precautions......................................................... 3
Supplied Accessories........................................ 5
Features .............................................................. 5
Getting to Know the CD Player ......................... 7
Front Panel ....................................................... 7
Display .............................................................. 8
Rear Panel........................................................ 8
Remote Controller............................................. 9
Installing the Batteries .................................... 10
Aiming the Remote Controller......................... 10
Disc Notes......................................................... 11
Connecting the CD Player ............................... 13
Audio Connections.......................................... 13
Connections ............................................... 14
Connecting the Power Cord............................ 15
Basic Operation................................................ 15
Turning On CD Player .................................... 15
Setting Auto Standby (ASb)............................ 15
Changing the Display Brightness.................... 15
Disc Playback ................................................... 16
Using the Remote Controller .......................... 17
Displaying CD Information .............................. 17
Selecting Files (MP3 CDs).............................. 18
Selecting Files in Navigation Mode................. 18
Selecting Files in All Folder Mode .................. 19
Selecting a Folder during Playback
(Search Mode).............................................. 19
Displaying MP3 Information............................ 20
Various Playback Modes ................................. 21
Random Playback........................................... 21
Memory Playback (For Audio CDs) ................ 21
Memory Playback (For MP3 CDs) .................. 22
Repeat Playback............................................. 23
Setting for MP3................................................. 24
Setting MP3 Preferences................................ 24
Troubleshooting............................................... 26
Specifications................................................... 27
En-6
SN29402439_C-755_En.book
7 ページ
2016年8月9日
火曜日
午後2時14分
Getting to Know the CD Player
Front Panel
1
6
2
3
7
1. Í ON/STANDBY button (15)
Press to turn on or standby the C-755.
2. Disc tray (16)
The CD is loaded here.
3. Open/Close [<] button (16)
Press to open and close the disc tray.
4. Stop [∫] button (16 , 18, 19, 25)
Press to stop playback.
5. Play/Pause [1/;] button (16, 18, 19, 21, 22,
26)
Press to start/pause playback.
5
4
8
6. Remote control sensor (10)
Receives control signals from the remote
controller.
7. Display (8)
See next page.
8. [:]/[9] buttons (16, 26)
Press to select the previous or next track.
Hold down the buttons to fast-reverse or fastforward during playback.
En-7
SN29402439_C-755_En.book
8 ページ
2016年8月9日
火曜日
午後2時14分
Getting to Know the CD Player-Continued
Display
1
2
4
3
6
5
7
1.
indicators
The 1 indicator lights up for playback.
The ; indicator lights up while playback is
paused.
8
9
10
REPEAT 1 lights up when repeat playback is
selected for one track.
1;
7. Message area
Various information is displayed here.
2. MP3 indicator
Lights up when an MP3 CD is loaded.
8. TITLE, ARTIST, and ALBUM indicators
TITLE lights up when the title (ID3 tag) of an
MP3 track is being displayed.
3. FOLDER indicator
Lights up when folder playback is selected.
ARTIST lights up when the artist name from an
MP3 track (ID3 tag) is being displayed.
ALBUM lights up when the album name from
an MP3 track (ID3 tag) is being displayed.
4. FILE indicator
Lights up when an MP3 file number is being
displayed.
5. TRACK indicator
Lights up when a CD track number is being
displayed.
6. Playback mode indicators
MEMORY lights up when memory playback is selected.
RANDOM lights up when random playback is selected.
REPEAT lights up when repeat playback is
selected for all tracks.
9. DISC, TOTAL indicators
These indicators light up when the total disc
time or track time is being displayed.
10. REMAIN indicator
This indicator lights up when the remaining disc
time or track time is being displayed.
Rear Panel
1
2
1. AC INLET (15)
The supplied power cord is connected.
2. ANALOG AUDIO OUTPUT jacks (13, 14)
These analog audio outputs can be connected
to an amplifier’s analog inputs by using the
audio cable (not supplied).
3. DIGITAL AUDIO OUTPUT COAXIAL jacks
Digital audio outputs can be connected to a
digital audio input on an amplifier or recorder.
En-8
3
4.
4
REMOTE CONTROL jacks (14)
These two identical
(Remote Interactive)
jacks can be connected to the
jacks on your
other Onkyo components for interactive
control. To use , the C-755 must be
cable and an audio
connected with an
cable.
SN29402439_C-755_En.book
9 ページ
2016年8月9日
火曜日
午後2時14分
Getting to Know the CD Player-Continued
Remote Controller
The page numbers in parentheses show where you can find the main explanation for each item.
5. Play [1] button (16 – 19, 21, 22)
Press to start playback.
13
1
DIMMER
DISPLAY
14
2
6. [:]/[9] buttons (16, 17, 19, 21)
Press to select the previous or next track.
7. Stop [∫] button (16, 18, 19, 24)
Press to stop playback.
8.
3
4
5
6
RANDOM
REPEAT
15
16
7
/ /</> buttons (15, 18, 19, 21, 22, 24)
Press the Arrow buttons to configure various
settings, and then press the ENTER button to
set them.
These buttons can be also used to select a
track.
9. ENTER button (15, 19, 21 – 24)
Press to set a selected preference.
10. SEARCH button (19)
For MP3 CDs, this button is used to search and
select a file number or a folder number.
11. SETUP button (24)
Press to access various settings.
8
ENTER
12. Number buttons (17, 19)
Use to enter track numbers.
13. Open/Close [<] button (16)
Press to open and close the disc tray.
9
14. DISPLAY button (17, 20)
Press to change the displayed information.
10
11
12
SETUP
SEARCH
MEMORY
1
2
3
4
5
6
7
8
9
>10
0
CLEAR
17
15. REPEAT button (23)
Select the repeat playback or 1-repeat
playback mode.
16. [22]/[11] buttons (17, 21)
Hold down to fast-reverse or fast-forward
during playback.
17. MEMORY button (21, 22)
Select the Memory playback mode.
18
18. CLEAR button (21)
Use to clear any numbers that have been
entered during numeric input. When making a
memory setting, the selected track is erased.
RC-822C
1. [Í] button (15)
Press to turn on or standby the C-755.
2. DIMMER button (15)
Press to adjust the display brightness.
3. Pause [;] button (16, 17)
Press to pause playback.
4. RANDOM button (21)
Select the Random playback mode.
En-9
SN29402439_C-755_En.book
10 ページ
2016年8月9日
火曜日
午後2時14分
Getting to Know the CD Player-Continued
Installing the Batteries
1
To open the battery compartment, press the
small hollow and slide open the cover.
Aiming the Remote Controller
When you operate the remote controller, point it at the CD
Player’s remote control sensor, as shown below.
Remote control sensor
x. 5
p ro
Ap ft.)
(1 6
m
DIMM
ER
DISPL
AY
RANDO
M
REPEA
T
ENTER
SETUP
SEAR
1
CH
MEMO
4
2
7
RY
5
>10
3
8
6
0
CLEA
9
R
RC-82
2C
2
Insert two batteries (R03/AAA) into the
compartment.
Carefully follow the polarity diagram (positive
(+) and negative (–) symbols) inside the
battery compartment.
Batteries are not supplied with products for China.
3
Replace the cover and slide it shut.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types
of batteries.
• If you intend not to use the remote controller for a
long time, remove the batteries to prevent
damage from leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or
corrosion.
En-10
Notes:
• The remote controller may not work reliably if the
CD Player is subjected to bright light, such as
direct sunlight or inverter-type fluorescent lights.
Keep this in mind when installing.
• If another remote controller of the same type is
used in the same room, or the CD Player is
installed close to equipment that uses infrared
rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote
controller because the buttons may be pressed
inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the
CD Player is installed in a rack behind colored
glass doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and CD Player’s remote
control sensor.
SN29402439_C-755_En.book
11 ページ
2016年8月9日
火曜日
午後2時14分
Disc Notes
Precautions for Playback
Playback of MP3 Discs
Compact discs (CDs) with the following logo on the label
surface can be used.
Do not use discs designed for purposes other than audio,
such as CD-ROMs for PC use. Abnormal noise could
damage the speakers or amplifier.
• Only MP3 files with the extension “.MP3” or “.
mp3” are supported.
• This CD player supports files recorded in MPEG
1 Audio Layer 3 (32-320kbps), with a sampling
frequency of 32/44.1/48 kHz.
• Variable bitrates (VBR) between 32kbps and
320kbps are supported. The time information
during VBR playback may not display correctly.
* This CD player supports CD-R and CD-RW discs.
Note that some discs may not play back because of the
disc characteristics, scratches, contamination or the
recording state. A disc recorded with an audio CD
recorder will not play back unless it is finalized.
Never use discs which have an unusual shape (such as
hearts or octagons). These types of discs could jam and
damage the CD player.
Handling Discs
Hold discs by the edge, or by the center hole and edge.
Avoid touching the playback surface (surface with nothing
printed on it).
Label surface
(printed surface)
Playback surface
CD Playback with Copy-control Function
Do not attach paper or stickers, or write on the playback
or label surface of the disc. Take care not to scratch or
damage the disc.
Some audio CDs with copy-control functionality do not
comply with official CD standards. These are special discs
and cannot be played with this CD player.
Playback of MP3 Discs
MP3 files recorded on a CD-R/CD-RW can be played with
this CD player.
• Use discs which have been recorded following the
ISO9660 Level 2 file system. (The supported
directory depth is eight levels, the same as
ISO9660 Level 1)
• Discs recorded with the hierarchical file system
(HFS) cannot be played.
• Up to 99 folders (including the root folder), and up
to 499 files (including root) and files can be
recognized and played.
Notes:
• A disc recorded with a recorder or personal
computer may not play in some cases. (Cause:
Disc’s characteristics, damaged or dirty disc, dirt
on player’s lens, dew condensation, etc.)
• A disc recorded on a personal computer may not
play because of the application settings or
environment. Record the disc with the proper
format. (Contact the application maker for
details.)
• A disc with insufficient storage capacity may not
play back properly.
En-11
SN29402439_C-755_En.book
12 ページ
2016年8月9日
火曜日
Disc Notes-Continued
Precautions for Rental Discs
Do not use discs with residue from cellophane tape, rental
discs with labels which are peeling off, or discs with
decorative labels. This type of disc could get stuck in the
CD player, or could damage the CD player.
Precautions for Inkjet Printable Discs
Do not leave a CD-R/CD-RW having a label printed with
an inkjet printer in the CD player for a long time. The disc
could get stuck in the CD player, or could damage the CD
player.
Remove the disc from the CD player when not being
played, and store it in a case. A freshly printed disc will
stick easily, and should not be played immediately.
Caring for Discs
If the disc is dirty, the C-755 will have a hard time reading
signals, and the audio quality may drop. If the disc is dirty,
gently wipe off fingerprints and dust with a soft cloth.
Lightly wipe from the center outwards.
To remove stubborn dust or dirt,
wipe the disc with a soft cloth
dampened with water, and then
dry it with a dry cloth. Do not use
cleaning spray for analog
records or antistatic agents, etc.
Never use volatile chemicals
such as benzine or paint thinner
as they can impregnate the disc
surface.
En-12
午後2時14分
SN29402439_C-755_En.book
13 ページ
2016年8月9日
火曜日
午後2時14分
Connecting the CD Player
Audio Connections
• Before making any connections, read the manuals supplied with your other components.
• Don’t connect the power cord until you’ve completed and double-checked all connections.
• We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies.
Connection Color Coding
RCA-type audio connections are usually colorcoded: red and white. Use red plugs to connect
right-channel audio inputs and outputs (typically
labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”).
Left (white)
Analog audio
cable
Right (red)
• To prevent interference, keep audio cables away
from power cords and speaker cables.
Coaxial Digital Jack
The unit supports 16 bit, 44.1 kHz PCM signal digital output.
Note:
Do not put anything on top of the C-755, as it may
interfere with proper ventilation.
Left (white)
Right (red)
• Push plugs in all the way to
make good connections
(loose connections can
cause noise or malfunctions).
Right!
Wrong!
Disconnect the power
cord before making
any connections!
RCA/phono
audio cable
(not supplied)
Coaxial cable
(supplied)
CD
Coaxial IN
Hi-fi amp, AV receiver
Coaxial cable
(supplied)
Coaxial IN
CD-R, MiniDisc, DAT recorder
En-13
SN29402439_C-755_En.book
14 ページ
2016年8月9日
火曜日
午後2時14分
Connecting the CD Player-Continued
Connections
With
(Remote Interactive) you can control the
-compatible
C-755 together with your other
Onkyo AV components. With some Onkyo AV
receivers you can use one remote controller to control all your Onkyo components and use the followfunctions:
ing special
Direct Change
If your C-755 is connected to an
-compatible
Onkyo hi-fi amp or AV receiver, when you start playback on the C-755, the AV receiver will select the
C-755 as the input source.
Remote Control Operation
You can control the C-755 by using your Onkyo
amplifier’s remote controller. See the amplifier’s
instruction manual for details.
To use the functions, you need to connect one of
connectors to an
connector on
the C-755’s
another AV component in your system by using the
supplied
cable.
See the manuals supplied with your other -compatible AV components for more information.
Notes:
• Use only
cables for
connections.
• The C-755 has two
connectors. You can connect either one to your Onkyo hi-fi amp or AV
receiver. The other connector is for connecting
-compatible components.
additional
• Connect the C-755’s
connector only to Onkyo
AV components. Connecting to other manufacturer’s AV components may cause them to malfunction.
• Some Onkyo
-compatible AV components
may not support the special functions described
here.
To use
you must make an analog audio connection
(RCA/phono) between the C-755 and your other Onkyo
component even if they are connected digitally.
Coaxial cable (supplied)
RCA/phono audio cable (not supplied)
L
CD
R
Coaxial IN
Onkyo Hi-fi amp, AV receiver
En-14
Disconnect the power
cord before making any
connections!
cable (supplied)
SN29402439_C-755_En.book
15 ページ
2016年8月9日
火曜日
午後2時14分
Connecting the Power Cord
Before connecting the power cord, connect all of the other components.
Plug the power cord into a
suitable electrical outlet
Basic Operation
Make settings for this function while playback is
stopped.
Turning On CD Player
ON/STANDBY
DIMMER
DISPLAY
To turn on the CD Player, press the
[Í ON/STANDBY] button on the unit or the remote
controller. Press the
[Í ON/STANDBY] button again to set the CD
Player to Standby.
Setting Auto Standby (ASb)
1
Press the [SETUP] button.
2
Use the [<] or [>] button to display “ASb”;
then press the [ ENTER ] button.
3
Use the [<] or [>] button to switch “Off” or
“On”; then press the [ ENTER ] button.
4
“COMPLETE” appears on the display.
Note:
If playback is paused, the power will remain on
even after 30 minutes have elapsed; the Auto
Standby function will not operate.
Changing the Display Brightness
Press the remote controller’s [DIMMER]
button repeatedly to select the following
options:
DIMMER
ENTER
ENTER
Normal
SETUP
SEARCH
MEMORY
1
2
3
Dim
Dimmer
SETUP
You can specify that if the CD Player is left stopped
for 30 minutes, the power will automatically turn off,
placing the unit in Standby mode (Auto Standby
function).
On the European model:
The default setting is “On”.
On the China model:
The default setting is “Off”.
En-15
SN29402439_C-755_En.book
16 ページ
2016年8月9日
火曜日
午後2時14分
Disc Playback
Disc tray
DIMMER
DISPLAY
RANDOM
REPEAT
ENTER
1
Press the Open/Close [<] button to open
the disc tray.
2
Place the CD on the tray with the label-side
facing up.
If you're playing an 8 cm CD, place it in the
center of the tray.
3
To start playback, press the Play/Pause [1/
;] button. (Remote controller: [1])
The disc tray closes and playback starts.
The contents of the disc are displayed when you use the
Open/Close [<] button to load a disc and when you press
the Stop [∫] button during playback.
Example displays:
• Audio CD
“DISC TOTAL” lights up.
Selecting Tracks
To return to the beginning of the track that’s currently playing or paused, press the Previous [:] button.
Press the Previous [:] button repeatedly to select earlier tracks.
Press the Next [9] button repeatedly to select subsequent tracks.
• To Fast-Forward or Fast-Reverse
During playback or while playback is paused,
hold down the [9] button on the CD Player to
fast-forward or the [:] button on the CD Player
to fast-reverse.
If you use the remote controller, use the [22]/
[11] buttons.
On MP3 CDs, fast-reverse only works within the
MP3 file that’s currently playing.
• To Pause Playback
Press the Play/Pause [1/;] button. The Pause
[;] indicator appears.
To resume playback, press the Play/Pause [1/;]
button again. (Remote controller: [1])
• To Stop Playback
Total number
of tracks
Total playing time
• MP3 Discs
Disc name or Format
Press the Stop [∫] button.
• To Eject the CD
Press the Open/Close [<] button to open the
disc tray.
Notes:
- MP3 CDs -
Total number
of folders
En-16
Total number
of files
If you press the [:] button during playback or while
playback is paused, the beginning of the current file is
selected.
If you select a file while playback is stopped, press the
Play/Pause [1/;] button to start playback. (Remote
controller: [1])
You can select MP3 files in other folders by using the
[:]/[9] buttons.
SN29402439_C-755_En.book
17 ページ
2016年8月9日
火曜日
午後2時14分
Disc Playback-Continued
Using the Remote Controller
DIMMER
[DISPLAY]
Press repeatedly to display
CD information
See below for details.
DISPLAY
[;]
Press to pause playback
[1]
Press to start playback
RANDOM
REPEAT
[22]/[11]
Press to fast-forward or fastreverse
[:]/[9]
Press to select tracks
• Press the Previous [:] button to
locate the beginning of the currently playing or paused track. Press it repeatedly
to select earlier tracks.
• Press the Next [9] button repeatedly
to select subsequent tracks.
During playback or while playback is
paused, press and hold the Fast Forward [11] button to fast-forward, or the
Fast Reverse [22] button to fastreverse.
SETUP
SEARCH
MEMORY
1
2
3
4
5
6
For MP3 files, you can select files in other
folders.
[∫]
Press to stop playback
Use the number buttons as
shown in the examples below to
select tracks.
To select:
Track #8
7
>10
8
0
8
9
Track #10
>10
1
0
CLEAR
Track #34
>10
3
4
>10
RC-822C
Press:
Used to enter numbers over 9.
With MP3 CDs, you can select files in
the current folder using these buttons.
Displaying CD Information
Press the remote controller’s [DISPLAY] button (repeatedly) to show the following CD information.
During Playback or While Playback is Paused
DIMMER
No
indicator.
DISPLAY
DISPLAY
The elapsed time is normally
displayed.
“REMAIN”
While Playback is Stopped
Lights up while the remaining
track time is being displayed.
“TOTAL
REMAIN”
Total number of tracks
Total playing time
Lights up while the remaining disc time is
being displayed.
If the total time is more than 99 minutes
and 59 seconds, “– –:– –” is displayed.
See page 20 for details on displaying MP3 information.
En-17
SN29402439_C-755_En.book
18 ページ
2016年8月9日
火曜日
午後2時14分
Disc Playback-Continued
Selecting Files (MP3 CDs)
Selecting Files in Navigation Mode
For MP3 CDs, files (MP3 files) may be organized in a
hierarchy, with folders containing files and subfolders, as
shown below.
In Navigation mode, you can select files by navigating
through the folder hierarchy. This mode can only be used
while playback is stopped.
• In this manual, MP3 files are referred to as
files. Likewise, folders (directories) are
referred to as folders.
Root
Folder #1
File #1
DIMMER
DISPLAY
File #10
Folder #2
Folder #3
Folder #4
RANDOM
File #11
REPEAT
File #14
File #12
ENTER
ENTER
File #13
File #18
If you don’t select a specific MP3 file or folder for
playback, all of the MP3 files on the CD will be played in
numerical order starting with file #1.
On this CD Player, there are two modes for selecting files
(MP3 files): Navigation mode and All Folder mode.
In Navigation mode, you can select files (MP3 files) by
navigating through the folder hierarchy, moving in and out
of folders and subfolders.
In All Folder mode, all folders appear at the same level,
making it easy to select folders regardless of the
hierarchy.
While playback is stopped, press the remote
controller’s [∫] or [ ] button to enter Navigation
mode, the [;] or [ ] button to enter All Folder mode.
If you use the CD Player’s button, press the [∫] button
to enter Navigation mode, press and hold the [∫]
button to enter All Folder mode.
You can change the way in which these buttons change
the playback mode. This lets you disable the file selection
methods described in Navigation mode or All Folder
mode. (See “STOP KEY” in “Setting MP3 Preferences” on
page 25.)
En-18
1
While playback is stopped, press the [ ] or
[∫] button.
The compact disc player enters Navigation
mode and “[ROOT]” appears on the display.
2
Press the [ ] or [ENTER] button (front
panel: [1/;]).
The first folder name in ROOT appears on the
display.
If the disc contains no folders, the first file
name appears.
3
Use the [<]/[>] or [:]/[9] buttons to
select other folders and files at the same
level.
To move up a level, press the [ ] or [;] button
(front panel: [∫]).
Folders that don’t contain files or subfolders
can’t be selected.
4
Press the [ENTER] or [ ] button to move
down a level (front panel: [1/;]).
5
Use the [<]/[>] or [:]/[9] buttons to
select a file in the folder.
SN29402439_C-755_En.book
19 ページ
2016年8月9日
火曜日
午後2時14分
Disc Playback-Continued
6
Press the [ENTER] or [1] button. (front
panel: [1/;])
Playback will start with the specified file or
folder and continue until all of the files on the
disc have been played.
To select another folder, press the [;] button
again (front panel: [∫]), and then use the [:]/
[9] buttons to select it.
4
To cancel the procedure at any point, press the [∫].
Note:
• The behavior of the [∫] on the CD Player can be
set from “STOP KEY” preference (page 25).
Selecting Files in All Folder Mode
In All Folder mode, you don’t have to navigate the folder
hierarchy because all folders that contain files appear at
the same level. This mode can only be used while
playback is stopped.
Press the [ENTER] or [1] button to start
playback.
Playback will start with the specified file or
folder and continue until all of the file on the
disc have been played.
To cancel the procedure at any point, press the [∫].
∫ To Select Folders and Files by Number
1. Use the number buttons as shown in the
examples below to enter folder/file numbers.
To select:
Folder/File #8
>10
1
0
Folder/File #34
>10
3
4
Used to enter numbers over 9.
2. Playback starts. When you enter folder number,
playback will start from the first file in the selected
folder. If a folder contains more than 99 files, single
and double-digit file numbers must be preceded by
zeros. For example, to specify file #8, press >10, 0, 0,
and 8. To specify file #34, press >10, 0, 3, and 4. To
specify file #134, press >10, 1, 3, and 4.
DISPLAY
RANDOM
8
Folder/File #10
>10
DIMMER
Press:
REPEAT
Note:
• The behavior of [∫] on the CD Player can be set
from “STOP KEY” preference (page 25).
Selecting a Folder during Playback
(Search Mode)
ENTER
ENTER
RANDOM
1
While playback is stopped, press the [ ] or
[;] button (front panel: press and hold the
[∫]).
The CD Player enters All Folder mode, and “1” appears on the display.
REPEAT
ENTER
ENTER
SEARCH
2
3
Use the [<]/[>] or [:]/[9] buttons to
select the other folders.
You can select any folder that contains files.
Press the [ ] button (front panel: [1/;]).
The first file name inside the folder appears.
Use the [<]/[>] or [:]/[9] buttons to select
the files within the folder.
1
SETUP
SEARCH
MEMORY
1
2
3
4
5
6
Press the [SEARCH] button.
The display blinks.
En-19
SN29402439_C-755_En.book
20 ページ
2016年8月9日
火曜日
午後2時14分
Disc Playback-Continued
2
To select the previous folder, press the
Previous [<] button.
To select the next folder, press the Next [>]
button.
3
Press the [ENTER] button to display the file
name, and start playback the selected file.
When there is no ID3 tag, “ARTIST-NO DATA” appears.
Album name: Name of the album (if ID3 tag is present).
When there is no ID3 tag, “ALBUM-NO DATA” appears.
4
Use the Previous [:] and Next [9]
buttons to select the previous or next file,
and start playback.
Note:
Sampling rate and bit rate: Sampling rate and bit rate of
the current file.
The [SEARCH] button cannot be used during “Random
Playback” or “Memory Playback”.
Displaying MP3 Information
DIMMER
DISPLAY
DISPLAY
You can display various information about the MP3 file
currently playing, including ID3 tags such as title name,
artist name, and album name.
During playback, press the [DISPLAY] button
repeatedly to display the following MP3
information.
Elapsed file time: The length of time that the current file
has been playing (default display). If the elapsed time is
more than 99 minutes and 59 seconds, “– –:– –” is displayed.
File name: Name of the current file.
Folder name: Name of the current folder.
Title: Title of the current file (if ID3 tag is present). When
there is no ID3 tag, “TITLE-NO DATA” appears.
Artist name: Name of the artist (if ID3 tag is present).
En-20
Notes:
• To display the disc name, press the [DISPLAY]
button while playback is stopped.
• If a file or folder name contains any characters
that cannot be displayed, an underscore will
appear in place of those characters. Alternatively,
you can set the CD Player so that names
containing such characters are displayed as
“FILE n” or “FOLDER n,” “n” being the file or
folder number (see “BAD NAME” on page 24).
SN29402439_C-755_En.book
21 ページ
2016年8月9日
火曜日
午後2時14分
Various Playback Modes
You can select the following playback modes:
• Random playback
• Memory playback
• Repeat playback
Memory Playback (For Audio CDs)
In memory playback, you can create a playlist of up
to 25 files.
Random Playback
DIMMER
With random playback, all of the files on the disc
are played in random order.
DISPLAY
DISPLAY
RANDOM
RANDOM
RANDOM
REPEAT
REPEAT
ENTER
ENTER
ENTER
1
While playback is stopped, press the [RANDOM] button; the RANDOM indicator
appears.
SETUP
SEARCH
MEMORY
1
2
3
4
5
6
MEMORY
RANDOM indicator
7
8
>10
0
9
CLEAR
CLEAR
RC-822C
2
To start random playback, press the Play
[1] button. (front panel: [1/;])
Track currently playing
Memory playback can be set only when playback is
stopped.
1
Press the [MEMORY] button; the MEMORY
indicator appears.
MEMORY indicator
∫To Cancel Random Playback
• Stop playback, then press the [RANDOM] button
to change the playback mode. The RANDOM
indicator disappears, and random playback is
cancelled.
• Random playback is cancelled when the disc is
ejected.
Playlist number
En-21
SN29402439_C-755_En.book
22 ページ
2016年8月9日
火曜日
午後2時14分
Various Playback Modes-Continued
2
Use the Previous and Next [<]/[>] buttons to
select the first file you want to add to the
playlist, and then press [ENTER] button.
∫To Cancel Memory Playback
• Stop playback, then press the [MEMORY] button to
change the playback mode. The MEMORY indicator disappears, and memory playback is cancelled.
• Memory playback is cancelled when the disc is
ejected.
Memory Playback (For MP3 CDs)
Track to be added
to the playlist
Total time of
playlist
RANDOM
Repeat this step to add additional files to the playlist.
Alternatively, you can use the number buttons on the
remote controller to select files instead of the Previous and Next [<]/[>] and the [ENTER] buttons.
Notes:
• If the total playing time is more than 99 minutes and 59 seconds, “– –:– –” appears.
• You can add up to 25 files to the playlist. If you try
to add more, the message “MEM FULL” appears.
3
To start memory playback, press the
[ENTER] button. Memory playback starts.
Alternatively, you can start playback with the
Play [1] button.
REPEAT
ENTER
ENTER
SETUP
SEARCH
MEMORY
1
2
3
MEMORY
Memory Playback in Navigation Mode
Memory playback can be set only when playback is
stopped.
Track currently playing
∫To Change the Display
While creating a playlist for memory playback, you
can press the [DISPLAY] button to change the display information as follows:
Total playback
time of the
memorized files
Memory
number
Press the [MEMORY] button; the MEMORY
indicator appears.
MEMORY indicator
Current playback time of the
selected file
∫To Select Other Files During Memory
Playback
Use the Previous and Next [:]/[9] buttons.
∫To Check What’s on the Playlist
While playback is stopped, use the Fast Reverse
and Fast Forward [22]/[11] buttons to scroll
through the playlist.
∫To Remove Files from the Playlist
• While memory playback is stopped, press the
[CLEAR] button. Each press removes the last file
from the playlist.
• The playlist is deleted when you change the playback mode (i.e., when you press the [MEMORY]
button after stopping playback).
En-22
1
2
Press the [∫] or [ ] button.
The CD Player enters Navigation mode and
“ROOT” appears on the display.
3
Press the [ENTER] button.
The first folder name in ROOT appears on the
display.
4
Use the [<]/[>] buttons to select other folders and files at the same level.
Folders that don’t contain files or subfolders
can’t be selected. Repeat steps 3 and 4 to
select the files and subfolders in that folder.
5
Press the [ENTER] button.
The first item is memorized in the playlist.
SN29402439_C-755_En.book
23 ページ
2016年8月9日
火曜日
午後2時14分
Various Playback Modes-Continued
6
Use the [ ]/[<]/[>] buttons to continue
selecting other items for memory playback.
To move up a level, press the [ ] button.
To continue selecting items for memory playback, repeat steps 4 and 5.
To memorize other items of the same folder in
the playlist, use the [<]/[>] buttons to select
items, then press the [ENTER] button.
7
Press the Play [1] button. (front panel: [1/
;])
Memory playback starts.
Repeat Playback
In repeat playback, you can play an entire CD
repeatedly, play one track repeatedly, or combine it
with memory playback to play the playlist repeatedly, or random playback to play all of the tracks on
the disc in random order repeatedly.
REPEAT
RANDOM
REPEAT
Memory Playback in All Folder Mode
Memory playback can be set only when playback is
stopped.
1
Press the [MEMORY] button; the MEMORY
indicator appears.
2
Press the [;] or [ ] button. (front panel: [1/
;])
The CD Player enters All Folder mode and “1-”
appears on the display.
3
4
5
6
Use the [<]/[>] buttons to select the folder.
7
Press the [ ] button, then repeat steps 3 to
6.
To memorize other files of the same folder in the
playlist, repeat steps 5 to 6.
8
Press the Play [1] button. (front panel: [1/
;])
Memory playback starts.
Press the [ENTER] button.
Use the [<]/[>] buttons to select the file.
Press the [ENTER] button.
The first file is memorized in the playlist.
ENTER
Press the [REPEAT] button; the “REPEAT ALL”
or “REPEAT1” indicator appears.
Repeat-1 playback can’t be combined with memory
playback or random playback.
∫To Cancel Repeat Playback
• Press the [REPEAT] button repeatedly until
“REPEAT OFF” appears. (The REPEAT indicator
disappears.)
• Repeat playback is cancelled when the disc is
ejected.
∫To Change the Display
While creating a playlist for memory playback, you
can press the [DISPLAY] button to change the display information as follows:
File name
Folder name
Memory
number
En-23
SN29402439_C-755_En.book
24 ページ
2016年8月9日
火曜日
午後2時14分
Setting for MP3
Setting MP3 Preferences
The MP3 preferences let you change the way MP3
file information is displayed and the way MP3 CDs
are played.
RANDOM
REPEAT
ENTER
ENTER
SETUP
SEARCH
MEMORY
1
2
3
SETUP
The MP3 preferences can be set only when
playback is stopped.
1
2
Press the [SETUP] button.
Use the [<]/[>] buttons to select the
preference you want to change.
The preferences are explained in the next column.
3
4
5
Press the [ENTER] button.
Use the [<]/[>] buttons to select the
preference’s options.
To cancel the procedure at any point, press
the [∫] button.
Press the [ENTER] button.
When the preference has been set, “COMPLETE” appears on the display.
Preferences
Below, the name of each preference is followed by
its options in parentheses, with the default option in
bold.
∫ DISC NAME (Display/Not)
This preference determines whether the disc name
is displayed when an MP3 disc is loaded.
∫ FILE NAME (Scroll/Not)
This preference determines whether the file name
scrolls across the display when an MP3 file is
selected.
En-24
∫ FOLDER NAME (Scroll/Not)
This preference determines whether the folder
name scrolls across the display when an MP3
folder is selected.
In Navigation mode (see page 18), the folder name
scrolls across the display regardless of this setting.
∫ BAD NAME (Replace/Not)
This preference determines whether file and folder
names that contain undisplayable characters are
replaced with “File n” or “Folder n,” “n” being the file or
folder number. When set to Not Replace, displayable
characters are displayed and underscore characters
are used in place of any undisplayable characters.
For ID3 tags, underscore characters are used in place of
undisplayable characters regardless of this preference.
Note:
File and folder names are scrolled in Navigation
mode (page 18) regardless of the FILE NAME and
FOLDER NAME preferences.
∫ ID3 VER. 1 (Read/Not Read)
This preference determines whether version 1.0/
1.1 tags are read and displayed. When set to Not
Read, version 1.0/1.1 tags are not displayed.
∫ ID3 VER. 2 (Read/Not Read)
This preference determines whether version 2.2/
2.3/2.4 tags are read and displayed. When set to
Not Read, version 2.2/2.3/2.4 ID3 tags are not
displayed.
∫ CD EXTRA (Audio/MP3)
This preference applies to CD Extra discs and
determines whether music in the audio session or
MP3 files in the data session are played.
∫ JOLIET (Use SVD/ISO9660)
This preference applies to MP3 discs in Joliet format
and determines whether the CD-Player reads the SVD
data or treats the disc as an ISO 9660 disc. Normally,
this preference doesn’t need to be changed.
SVD (Supplementary Volume Descriptor) supports
long file and folder names and characters other than
letters and numbers. Some CD burning software
refers to the Joliet format as “Windows format.”
∫ HIDE NUMBER (Disable/Enable)
This preference determines whether the numbers at
the beginning of file and folder names are hidden.
When you create an MP3 CD on a personal computer, you cannot normally determine the playback
order of the files. However, if you number the MP3
files in order, starting with 01, 02, 03, and so on,
they will play in that order. If you don’t want these
numbers to appear on the display, choose Enable.
The following table shows a few examples of
numbered file and folder names and how they will
appear with the Disable and Enable options.
SN29402439_C-755_En.book
25 ページ
2016年8月9日
火曜日
午後2時14分
Setting for MP3-Continued
File/folder name
Disable
Enable
01 Pops
01 Pops
Pops
10-Rock
10-Rock
Rock
16_Jazz
16_Jazz
Jazz
21st Century
21st Century
21st Century
05-07-20 Album
05-07-20 Album
Album
∫ STOP KEY (All Folder/Navigation/Disable)
This preference determines how the Stop [∫] button
on the CD Player works.
When the ALL Folder option is selected, pressing
the Stop [∫] button once selects All Folder mode.
When the Navigation option is selected, pressing
the Stop [∫] button once selects Navigation mode.
When the Disable option is selected, the CD Player
does not enter Navigation or All Folder mode when
you press the Stop [∫] button.
∫ ASb (On/Off)
Please refer to “Setting Auto Standby (ASb)”
(page 15) for details of the procedure.
On the European model:
The default setting is “On”.
On the China model:
The default setting is “Off”.
En-25
SN29402439_C-755_En.book
26 ページ
2016年8月9日
火曜日
午後2時14分
Troubleshooting
If you have any trouble using the CD Player, look for a solution in this section.
If you can’t resolve the issue yourself, try resetting the CD Player before contacting the dealer from whom
you purchased this unit.
To reset the CD Player to its factory defaults, turn it on and, while holding down the [9] button,
press the [1/;] button. “Clear” will appear on the display.
Note that resetting the CD Player will delete your custom settings.
Power
Can’t turn on the C-755.
• Make sure that the power cord is properly plugged into the wall outlet (page 15).
• Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.
Audio
There’s no sound.
• The C-755 is not connected properly. Check all connections and correct as necessary.
• The wrong input source is selected on your amplifier. Check your amplifier’s input source setting. Refer to
your amplifier’s manual.
CD
Can’t play a CD.
• The disc is upside down. Load the disc with the label-side facing up (page 16).
• The disc is dirty. Remove the disc and clean it (page 12).
• Condensation has formed inside the C-755. Unplug the power cord and leave the unit for two to three hours
in the room temperature unitl the condensation has evaporated.
• The disc is nonstandard. See “Disc Notes” on page 11.
CD playback skips.
• Install the C-755 in a location that is free of vibration.
• The disc is dirty. Remove the disc and clean it (page 12).
• The disc is very scratched. Replace the disc.
Can’t enter track numbers for memory playback.
• No such track on the CD. Enter another number (page 22).
It takes a long time to locate certain tracks.
• The disc is dirty. Remove the disc and clean it (page 12).
• The disc is very scratched. Replace the disc.
SETUP
Can’t access the SETUP menu.
• If any track has been selected even when the C-755 is stopped, you must place it into the full stop state by
pressing the [∫] button before you can view all the SETUP menus.
Remote Controller
The remote controller does not work.
• There are no batteries in the remote controller. Install new batteries (page 10).
• The batteries are expired. Replace with new batteries (page 10).
• The batteries are installed incorrectly. Check the batteries and correct as necessary (page 10).
En-26
SN29402439_C-755_En.book
27 ページ
2016年8月9日
火曜日
午後2時14分
Troubleshooting-Continued
• You’re not pointing the remote controller at the C-755’s remote sensor. Point the remote controller at the
C-755’s remote sensor (page 10).
• You’re too far away from the C-755. Move the remote controller closer to the C-755 (page 10). The remote
controller has a range of approximately 5 meters (16 ft.).
• A strong light source is interfering with the C-755’s remote sensor. Make sure that the C-755 is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.
• If the C-755 is installed in a cabinet with colored glass doors, the remote controller may not work reliably
when the doors are closed. Open the doors, or use a cabinet without colored glass.
does not work.
There’s no analog audio connection. To use
you must make an analog audio connection between the
C-755 and your Onkyo AV receiver, even if they are connected digitally.
Company is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused
by malfunctions of the unit. Before you record important data, make sure that the material will be recorded
correctly.
The C-755 contains a microcomputer for signal processing and control functions. In very rare situations,
severe interference, noise from an external source, or static electricity may cause it to lockup. In the
unlikely event that this should happen, unplug the power cord, wait at least 10 seconds, and then plug it
again.
Specifications
Frequency Response:
5 Hz – 20 kHz
∫Audio Outputs
Audio Dynamic Range:
100 dB
Digital Outputs:
1 (COAXIAL)
Analog Outputs:
1
THD (Total Harmonic
Distortion):
0.003 %
Signal to Noise Ratio:
105 dB
Rated RCA Output Level and
Impedance:
2.0 V (rms) / 540 Ω
Audio Output/Impedance
(Digital/Coaxial):
0.5 V p-p / 75 Ω
Operation Condition
Temperature/Humidity:
5 °C–35 °C/ 5 %–85 %
Power Supply
AC 220–230 V, 50/60 Hz
Power Consumption:
9W
∫Others
RI:
2
Specifications and features are subject to change
without notice.
Stand-by Power Consumption 0.3 W
275 × 87.7 × 283.2 mm
Dimensions:
(10 13/16 × 3 7/16 ×
(W × H × D)
11 1/8 inches)
Weight:
3.8 kg (8.4 lbs)
Disc Compatibility:*
Audio CD, CD-R,
CD-RW, MP3 (CD-R,
CD-RW)
* Discs that have not been properly finalized may only be
partially playable or not playable at all
En-27
SN29402439_C-755_En.book
28 ページ
2016年8月9日
火曜日
午後2時14分
2-3-12 Yaesu, Chuo-ku, Tokyo 104-0028 JAPAN
http://www.onkyo.com/
<U.S.A.>
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
http://www.us.onkyo.com/
<Germany>
Gutenbergstrasse 3, 82178 Puchheim, Germany
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
<UK>
Anteros Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex, HA4 6QQ United Kingdom
Tel: +44 (0)871-200-1996 Fax: +44 (0)871-200-1995
<Hong Kong>
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: +852-2429-3118 Fax: +852-2428-9039
http://www.hk.onkyo.com/
<PRC>
302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032,
Tel: +86-21-52131366 Fax: +86-21-52130396
http://www.cn.onkyo.com/
<Asia, Oceania, Middle East, Africa>
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
Корпорация О энд Пи
2-3-12, Яэсу, Чуо-ку, г. Токио, 104-0028, ЯПОНИЯ
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved.
Printed in Malaysia / Imprimé en Malaisie / Напечатано в Малайзии
F1608-0
SN 29402439
* 2 9 4 0 2 4 3 9 *
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising