NAD CI 980 Datasheet

NAD CI 980 Datasheet
CI 980 Multi-Channel Amplifier
Top-of-the-line, eight channel amplification for custom installation and distributed audio
systems. Outfitted with the latest high-efficiency switching technology, the component
is smaller and lighter, while maintaining low distortion and impedance, even with long
wire runs.
RELIABLE, FLEXIBLE, EASY q
FEATURES & DETAILS
u
u
Reliability, flexibility, and ease of installation of the CI 980 is unsurpassed. Its design is
space-efficient and will fit into standard racking units with rack ears and Phoenix speaker
connection blocks. The amplifier is fully protected from short circuit and overheating, and
automatically restores operation after a condition is rectified. The CI 980 is incredibly
flexible, with selectable local or global inputs and the ability to bridge channels to create
a single high-power channel.
u
Universal voltage to accommodate
marine or avionics installations
Compact 2U rack height with rack ears
u
Phoenix speaker connection blocks
q
Choose between a DC trigger or a signal-sensing turn on with auto shut-off to make
integration easy. The signal sensing circuit employs a sophisticated music sensing circuit
to prevent the false triggers common with noisy source components or other types of
interference noise like RF leakage or ground loops.
50 W x 8 @ 8 Ohms; 60W x 8 @ 4 Ohms;
120W @ 8 Ohms in Bridge Mode
u
u
EFFICIENT WITH LOW NOISE AND DISTORTION
Eight channels of clean,
low distortion power set up in
four stereo zone configuration
u
Detachable power cable for
easy service and upgrades
Indicator lamps for each zone that show
protection status and amplifier clipping
u
<0.5 W standby consumption
u
<0.03% THD; <0.04% IMD (SMPTE, CCIR)
u
>86dBA referenced to 1W
CI 980 Rear Panel q
Specifications CI 980
q
Continuous Output Power
8 Ohms
4 Ohms
8 Ohms (Mono, Bridge Mode)
8 x 50W (ref. rated THD, 20Hz-20Hz, all channels driven)
8 x 60W
120W
Rated THD
(250mW to rated power, CCIF IMD, DIM 100)
<0.03% (ref. 20Hz-20kHz)
Clipping Power
>155W (ref. 1kHz, 8 Ohms, 0.1% THD)
Damping Factor
>150 (ref. 8 Ohms, 50Hz and 1kHz)
Input Sensativity
1.1V (ref. rated power)
Voltage Gain
33dB
Frequency Response
±1dB (ref. 20Hz-20kHz)
Signal/Noise Ratio, A-Weighted
>80dB (ref. 1W)
>100dB (ref. 50W)
Minimum Input Signal to trigger (auto sense mode)
>20mV
Time to Automatic Standby
(without signal at input sense mode)
10 minutes
GENERAL
Rated Power
600W (120V 60Hz, 230V 50Hz)
Idle Power
<26W
Standby Power
<0.5W
Dimensions (W x H x D)*
483 x 105 x 323mm (19 x 4 3/16 x 12 3/4”)**
Net Weight
5.72kg (12.6lb)
Shipping Weight
7.1kg (15.65lb)
* Gross dimensions include feet, extended buttons and rear panel terminals. ** Non-metric measurements are approximate. NAD Electronics will not assume any liability for errors being made by retailers, custom
installers, cabinet makers, or other end users based on information contained in this document. Note: Installers should allow a minimum clearance of 55mm for wire/cable management.
NAD Electronics International reserves the right to change specifications or features without notice. NAD is a registered trademark of NAD Electronics International.
All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form whatsoever without the written permission of NAD Electronics
International. © 11/17 <!-- Generator: Adobe Illustrator 22.0.1, SVG Export Plug-In -->
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement