ESAB | SR-B 9 | Instruction manual | ESAB SR-B 9 User manual

ESAB SR-B 9 User manual
SR-B 9, SR-B 17, SR-B 26,
SR-B 26-HD, SR-B 18, SR-B 20,
SR-B 21, SR-B 400, XCT-B 400W
Instruction manual
0463 697 001 GB 20190827
TABLE OF CONTENTS
1
SAFETY .......................................................................................................
4
2
INTRODUCTION ..........................................................................................
8
2.1
Overview .................................................................................................
8
3
TECHNICAL DATA ......................................................................................
9
4
OPERATION ................................................................................................
11
4.1
General ....................................................................................................
11
4.2
Connections............................................................................................
11
4.3
Choice of electrode ................................................................................
11
4.4
Grinding...................................................................................................
12
4.5
Bending of the flexible torch .................................................................
12
MAINTENANCE ...........................................................................................
13
5.1
Daily .........................................................................................................
13
TROUBLESHOOTING .................................................................................
14
ORDERING SPARE PARTS ........................................................................
ORDERING NUMBERS .......................................................................................
WEAR PARTS......................................................................................................
15
16
18
5
6
7
Rights reserved to alter specifications without notice.
0463 697 001
© ESAB AB 2019
1 SAFETY
1
SAFETY
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and
Safety Data Sheets (SDSs).
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1.
2.
3.
Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
The workplace must:
○ be suitable for the purpose
○ be free from drafts
0463 697 001
-4-
© ESAB AB 2019
1 SAFETY
4.
5.
Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
•
•
•
•
Install and ground the unit in accordance with instruction manual.
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
Insulate yourself from work and ground.
Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
•
•
•
Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
Exposure to EMF may have other health effects which are unknown.
Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or work
cable around your body. Keep welding power source and cables as
far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
•
•
Keep your head out of the fumes.
Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
•
•
Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
0463 697 001
-5-
© ESAB AB 2019
1 SAFETY
MOVING PARTS - Can cause injuries
•
•
•
Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
Stop engine before installing or connecting unit.
Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
•
•
Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
Do not use on closed containers.
HOT SURFACE - Parts can burn
•
•
•
Do not touch parts bare handed.
Allow cooling period before working on equipment.
To handle hot parts, use proper tools and/or insulated welding gloves to
prevent burns.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be
potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations,
due to conducted as well as radiated disturbances.
0463 697 001
-6-
© ESAB AB 2019
1 SAFETY
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law,
electrical and/or electronic equipment that has reached
the end of its life must be disposed of at a recycling
facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved
collection stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
0463 697 001
-7-
© ESAB AB 2019
2 INTRODUCTION
2
INTRODUCTION
2.1
Overview
TIG torches SR-B 9, SR-B 17, SR-B 26, SR-B 26-HD, SR-B 18, SR-B 20, SR-B 21,
SR-B 400 and XCT-B 400W are intended for manual TIG welding and available with water or
air cooled versions.
Certain models are available with flex heads for unlimited movement in confined spaces.
Accessories for the product can be found in the "ACCESSORIES" chapter of this
manual.
The TIG torch is supplied with:
•
•
wear parts (except electrodes):
○ Ø 1.6 mm (0.063 in.) SR-B 9
○ Ø 2.4 mm (0.094 in.) SR-B 17
○ Ø 2.4 mm (0.094 in.) SR-B 26
○ Ø 2.4 mm (0.094 in.) SR-B 26-HD
○ Ø 2.4 mm (0.094 in.) SR-B 20
○ Ø 2.4 mm (0.094 in.) SR-B 21
○ Ø 2.4 mm (0.094 in.) SR-B 400
○ Ø 2.4 mm (0.094 in.) XCT-B 400W
instruction manual
0463 697 001
-8-
© ESAB AB 2019
3 TECHNICAL DATA
3
TECHNICAL DATA
Operating temperature range:
-10 to +40 °C (+14 to +104 °F)
Transportation temperature range:
-20 to +55 °C (+4 to +131 °F)
SR-B
SR-B
SR-B
SR-B
SR-B
SR-B
9
9V
17
17V
26
26V
9FX
17FX
26FX
AC [A] / %
80/60
100/60
140/60
DC [A] / %
110/60
140/60
200/60
0.5–1.6 mm
0.5–2.4 mm
0.5–4.0 mm
(0.02– 0.063 in.)
(0.02– 0.094 in.)
(0.02– 0.157 in.)
Ar
Ar/He
4&8m
(13 & 26 ft)
X
-
X
-
X
-
12 kV
113 V
SR-B
SR-B
SR-B
SR-B
SR-B
SR-B
XCT-B
26-HD
26V-HD
18
20
21
400
400W
18FX
20FX
21FX
X
X
X
X
X
26FX-HD
-
-
70 °C
-
(158 °F)
AC [A] / %
160/60
225/100
160/100
240/100
315/100
DC [A] / %
230/60
320/100
220/100
340/100
450/100
1.0–4.8
0.5–4.0 mm
0.5–3.2
(0.02– 0.157 in.)
(0.02– 0.126 in.)
1.0–4.0
(0.039–
(0.039–
0.189 in.) 0.157 in.)
Ar
Ar/He
4&8m
(13 & 26 ft)
X
0463 697 001
-
X
X
-9-
X
X
X
© ESAB AB 2019
3 TECHNICAL DATA
12 kV
113 V
Specification of the torch cooling circuit
(for water cooled torches only)
•
•
min. water pressure: 2.5 bar
max. water pressure: 4.0 bar
The necessary cooling power is dependent of the application, the welding parameters and
the length of the torch. Sufficiency of available cooling power can be verified by measuring
the return temperature of the cooling fluid. If the return temperature is above 60 °C (140 °F),
the cooling power should be increased or the welding current should be reduced.
Recommended minimum values for cooling power and coolant flow rate
Welding current /
Up to 300 A DC /
210 A AC
Up to 450 A DC /
315 A AC
Up to 500 A DC /
350 A AC
4m
1.0 kW / 1.0 l/min
1.2 kW / 1.2 l/min
1.6 kW / 1.4 l/min
8m
1.6 kW / 1.2 l/min
2.0 kW / 1.4 l/min
2.5 kW / 1.7 l/min
Torch length
For other application parameters or longer cables, refer to additional documents that may
have been included with your torch.
CAUTION!
Return temperatures of more than 60 °C can cause damage or destruction of the
torch. The cooler must always be filled with sufficient cooling liquid, refer the user
manual of the cooling unit. In case of a high thermal load on the torch, use a cooler
with sufficient capacity. Use only special cooling fluid containing corrosion inhibitors
for welding torches. We recommend using ESAB CoolingFluid.
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40 °C (104 °F), or below.
Protection class
The torches protection class machine side (EN 60 529)
IP3X
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects of 2.5 mm Ø and greater. Omitting second characteristic numeral.
0463 697 001
- 10 -
© ESAB AB 2019
4 OPERATION
4
OPERATION
4.1
General
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
Read the operating instructions for the welding components, e.g. power source and connect
accordingly.
4.2
Connections
Tighten the connections for the torch carefully to avoid overheating the connection,
connection interference, mechanical damage or leakage of liquid or gas.
Connect water connections to the torch so that the red terminal is always connected to the
corresponding red terminal and the blue terminals are always connected to the
corresponding blue terminals.
4.3
Choice of electrode
By alloying the tungsten electrode with 1% to 2% lanthanum or cerium the electron discharge
is increased, which gives better striking and restriking and therefore increased arc stability.
Alloyed tungsten electrodes have a longer service life, tolerate higher currents and are less
likely to leave tungsten residue in the weld.
Pure tungsten electrode (AC)
Green
WP
Used for welding light metal
alloys.
Cerium alloyed tungsten electrode Grey
(AC/DC)
WC20
Used for welding light metals
such as aluminium and
magnesium. Electrode tip must
be rounded when welding.
Lanthanum alloyed tungsten
electrode (DC)
Gold
WL15
Usually used for welding
stainless steel, steel, copper,
titanium etc.
Lanthanum alloyed tungsten
electrode (AC/DC)
Black
WL10
Used for welding light metal
alloys, stainless steel, steel,
copper, titanium etc.
Selection table
A / AC
A / DC
W
CeO2
La2O3
CeO2
La2O3
1.0 mm
(0.039 in.)
6.4/8.0 mm
(0.252/0.315 in.)
10–60
-
15–100
70–80
20–100
1.6 mm
(0.063 in.)
6.4/8.0/9.8 mm
(0.252/0.315/0.386 in.)
50–100
60–90
70–160
80–140
80–160
2.4 mm
(0.094 in.)
9.8/11.2/12.7 mm
100–160
(0.386/0.441/0.500 in.)
90–130
110–200
150–210 120–230
3.2 mm
(0.126 in.)
11.2/12.7 mm
(0.441/0.500 in.)
130–180 140–190 150–205 220–320 200–305
4.0 mm
(0.157 in.)
12.7 mm (0.500 in.)
180–230 200–250 180–270 330–420 250–420
0463 697 001
- 11 -
© ESAB AB 2019
4 OPERATION
4.4
Grinding
Grind tungsten electrodes according to the following table:
NOTE!
Tungsten electrodes must be grounded lengthways. If they are incorrectly grounded,
the arc may be unstable. When the welding current is increased, the angle must
also be increased.
When welding with alternating current (AC), the electrode end must be gently rounded.
Grinding the electrode is then unnecessary. Light grading of the edge is sufficient. The
electrode forms itself if it is carefully overloaded. If the tip becomes ball shaped while welding
using alternating current, this is a sign that the current is too high for the diameter of
electrode being used.
Welding current
Electrode angle
20 A
30°
20–100 A
30°–90°
100–200 A
90°–120°
over 200 A
120°
4.5
Bending of the flexible torch
The life of the flexible torch is limited. The
maximum bending angle should be
45 degrees.
The life of the torch head can be prolonged by
proper technique.
Always make sure that the torch head is
supported by the thumb when you bend. This
prevents damages at sharp bendings.
0463 697 001
- 12 -
© ESAB AB 2019
5 MAINTENANCE
5
MAINTENANCE
NOTE!
Regular maintenance is important for safe and reliable operation.
WARNING!
The mains supply must be disconnected before cleaning.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer attempts
any work to rectify any faults in the product during the warranty period.
5.1
•
•
•
•
•
Daily
Check that all cables and hoses are undamaged and that there are no kinks in them.
Check that the gas nozzle is free from defects and suitable for the work in question.
Check that the shielding gas flows evenly and without restriction.
Check that the electrode is undamaged and that the electrode has been ground to the
correct angle.
Check the water flow at the unit's return line.
0463 697 001
- 13 -
© ESAB AB 2019
6 TROUBLESHOOTING
6
TROUBLESHOOTING
Read the operating instructions for the welding components, e.g. power source.
If the measures described below are not successful, consult your dealer or the manufacturer.
Problem
The arc does not
strike
Cause
•
•
Solution
Cable or contact is poor.
Torch electrode is badly
oxidised.
There are impurities in the
shielding gas (moisture, air).
The electrode used is too
large or stubby at low current.
•
•
•
Replace with a smaller
electrode.
No trigger function •
Control cable
interrupted/faulty.
•
Check/repair.
Gas shielding is
poor
There are impurities in the
shielding gas (moisture, air).
There are impurities in the
base material (rust, lubricant).
Insufficient or total lack of
shielding
gas.
It is too draughty at the
welding site.
Welding spray has fastened
on the gas lens or the gas
hood.
•
Flush clean with
gas.
Clean the base
material.
Check contents of the gas
bottle/hoses and the pressure
setting.
Shield the welding area with
protective screens.
Clean or replace.
•
•
•
•
•
•
•
0463 697 001
- 14 -
•
•
•
•
•
Check the cable and contact.
Regrind along the length of
the electrode.
Flush clean with gas.
© ESAB AB 2019
7 ORDERING SPARE PARTS
7
ORDERING SPARE PARTS
CAUTION!
Repair and electrical work should be performed by an authorised service technician.
Use only original spare and wear parts.
SR-B 9, SR-B 17, SR-B 26, SR-B 26-HD, SR-B 18, SR-B 20, SR-B 21, SR-B 400,
XCT-B 400W is designed and tested in accordance with the international and European
standards IEC-/ EN 60974-7. On completion of service or repair work, it is the responsibility
of the person(s) performing the work to ensure that the product still complies with the
requirements of the above standard.
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see
esab.com. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
0463 697 001
- 15 -
© ESAB AB 2019
ORDERING NUMBERS
ORDERING NUMBERS
FX = flexible body, V = valve, HD = heavy duty, W = water cooled
Ordering no.
Type
Torch head
TSB 1025
TSB 3550
W
Switch Valve F head 4 m 8 m 4 m 8 m 12 m 16 m
13 ft 26 ft 13 ft 26 ft 39 ft 52 ft
0700025500
SR-B 9
X
0700025501
SR-B 9
X
0700025502
SR-B 9
X
0700025503
SR-B 9
X
0700025504
SR-B 9V
X
0700025505
SR-B 9V
X
0700025506
SR-B 9FX
X
X
0700025507
SR-B 9FX
X
X
0700025508
SR-B 17
X
0700025509
SR-B 17
X
0700025510
SR-B 17
X
0700025511
SR-B 17
X
0700025512
SR-B 17V
X
0700025513
SR-B 17V
X
0700025514
SR-B 17V
X
0700025515
SR-B 17V
X
0700025516
SR-B 17FX
X
X
0700025517
SR-B 17FX
X
X
0700025518
SR-B 26
X
0700025519
SR-B 26
X
0700025520
SR-B 26
X
0700025521
SR-B 26
X
0700025522
SR-B 26V
X
0700025523
SR-B 26V
X
0700025524
SR-B 26FX
X
X
0700025525
SR-B 26FX
X
X
0700025526
SR-B 26-HD
X
0700025527
SR-B 26-HD
X
0700025528
SR-B 26-HD
X
0700025529
SR-B 26-HD
X
0700025530
SR-B 26V-HD
X
0700025531
SR-B 26V-HD
X
0700025532
SR-B 26FXHD
0463 697 001
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
- 16 -
X
© ESAB AB 2019
ORDERING NUMBERS
0700025533
SR-B 26FXHD
X
0700025550
SR-B 18
X
0700025551
SR-B 18
X
0700025552
SR-B 18
X
0700025553
SR-B 18
X
0700025554
SR-B 18FX
X
X
0700025555
SR-B 18FX
X
X
0700025534
SR-B 20
X
0700025535
SR-B 20
X
0700025536
SR-B 20FX
X
X
0700025537
SR-B 20FX
X
X
0700025544
SR-B 21
X
0700025545
SR-B 21
X
0700025546
SR-B 21
X
0700025547
SR-B 21
X
0700025548
SR-B 21FX
X
X
0700025549
SR-B 21FX
X
X
0700025538
SR-B 400
X
0700025539
SR-B 400
X
0700025540
XCT-B 400W
X
0700025541
XCT-B 400W
X
0700025542
XCT-B 400W
X
0700025543
XCT-B 400W
X
0463698001
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Spare parts list
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see
esab.com. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Technical documentation is available on the Internet at www.esab.com.
0463 697 001
- 17 -
© ESAB AB 2019
WEAR PARTS
WEAR PARTS
Tungsten electrodes Eco
Ordering no.
150 mm
Ordering no.
175 mm
Diameter Colour
Code
Current
-
0151 574 009 Wolfram, pure
Ø 1.6
Green
WP
AC
Wolfram, pure
Ø 2.0
Green
WP
AC
0151 574 210 0151 574 010 Wolfram, pure
Ø 2.4
Green
WP
AC
0151 574 211
0151 574 011
Wolfram, pure
Ø 3.2
Green
WP
AC
-
0151 574 012 Wolfram, pure
Ø 4.0
Green
WP
AC
0151 574 237 0151 574 037 Cerium 2%
Ø 1.6
Grey
WC20
AC/DC
0151 574 242 -
Cerium 2%
Ø 2.0
Grey
WC20
AC/DC
0151 574 238 0151 574 038 Cerium 2%
Ø 2.4
Grey
WC20
AC/DC
0151 574 239 0151 574 039 Cerium 2%
Ø 3.2
Grey
WC20
AC/DC
0151 574 240 0151 574 040 Cerium 2%
Ø 4.0
Grey
WC20
AC/DC
0151 574 230 0151 574 050 Lanthanum 1.5% Ø 1.0
Gold
WL15
AC/DC
0151 574 231 0151 574 051 Lanthanum 1.5% Ø 1.6
Gold
WL15
AC/DC
0151 574 232 -
Lanthanum 1.5% Ø 2.0
Gold
WL15
AC/DC
0151 574 233 0151 574 052 Lanthanum 1.5% Ø 2.4
Gold
WL15
AC/DC
0151 574 234 0151 574 053 Lanthanum 1.5% Ø 3.2
Gold
WL15
AC/DC
0151 574 235 0151 574 054 Lanthanum 1.5% Ø 4.0
Gold
WL15
AC/DC
-
Gold
WL15
AC/DC
0151 574 245 -
Tungsten
electrodes Eco
0151 574 055 Lanthanum 1.5% Ø 4.8
SR-B 9, SR-B 20, SR-B 21
Nozzles, collets, collet bodies and gas lenses:
Bold = standard delivery
Item
Size
Description
Ordering no.
1
Long
Back cap
0365 310 051
Medium
0365 310 050
Short
0365 310 049
2
Heat shield
0366 960 017
3
Adaptor Jumbo gas lens
0157 123 026
Collet standard
0365 310 027
4
Ø 0.5
Ø 1.0
Ø 1.6
0365 310 028
Std. for SR-B 9
Ø 2.0
Ø 2.4
0463 697 001
0365 310 029
0700 025 662
Std. for SR-B 20/21
0365 310 030
Ø 3.0
0700 025 663
Ø 3.2
0365 310 091
- 18 -
© ESAB AB 2019
WEAR PARTS
5
Ø 1.0
Collet body standard
0365 310 037
Ø 1.6
Std. for SR-B 9
0365 310 038
Ø 2.4
Std. for SR-B 20/21
0365 310 039
Ø 3.2
6
7
not illustrated
Ø 1.0
not illustrated
9
0463 697 001
Collet body with gas lens
0157 121 016
Ø 1.6
0157 121 017
Ø 2.4
0157 121 018
Ø 3.2
0157 121 041
Ø 6.4 (No. 4)
Gas nozzle standard
0365 310 044
Ø 8.0 (No. 5)
L=30 mm
0365 310 045
Ø 9.8 (No. 6)
Std. for SR-B 9
0365 310 046
Ø 11.2 (No.7)
Std. for SR-B 20/21
0365 310 047
Ø 12.7 (No. 8)
0365 310 048
Ø 15.9 (No. 10)
0588 000 440
Ø 5.0 (No. 3)
Gas nozzle standard
0700 025 664
Ø 6.4 (No. 4)
L=48 mm
0700 025 665
Ø 8.0 (No. 5)
0700 025 666
Ø 9.5 (No. 6)
0700 025 667
Ø 6.5 (No. 4)
8
0365 310 090
L=63 mm
0700 025 668
Ø 8.0 (No. 5)
0700 025 669
Ø 9.5 (No. 6)
0700 025 670
Ø 6.5 (No. 4)
L=89 mm
0700 025 671
Ø 6.4 (No.4)
Gas nozzle for gas lens
0157 121 032
Ø 8.0 (No.5)
L=25.5 mm
0157 121 033
Ø 9.8 (No.6)
0157 121 034
Ø 11.2 (No.7)
0157 121 039
Ø 12.7 (No.8)
0157 121 040
Ø 6.4 (No. 4)
Gas nozzle for gas lens
0700 025 658
Ø 8.0 (No. 5)
L=35 mm
0700 025 659
Ø 9.8 (No. 6)
0700 025 660
Ø 11.2 (No.7)
0700 025 661
Ø 1.0
Collet for Jumbo gas lens
0700 025 672
Ø 1.6
0700 025 673
Ø 2.4
0700 025 674
Ø 3.2
0700 025 675
- 19 -
© ESAB AB 2019
WEAR PARTS
10
11
Ø 1.0-1.6
0700 025 676
Ø 2.4
0700 025 677
Ø 3.2
0700 025 678
Ø 9.8 (No. 6)
Collet for Jumbo gas lens
0157 123 088
Ø 12.7 (No. 8)
0157 123 089
Ø 15.9 (No. 10) L=48 mm
0588 000 438
Ø 19.0 (No. 12)
0157 123 098
Ø 24.0
0588 000 437
Ø 24.0
0463 697 001
Gas lens, Jumbo
L=34 mm
0700 025 679
- 20 -
© ESAB AB 2019
WEAR PARTS
SR-B 17, SR-B 26, SR-B 18
Nozzles, collets, collet bodies and gas lenses:
Bold = standard delivery
Item
Size
Description
Ordering no.
1
Long
Back cap
0157 123 029
Medium
0588 000 591
Short
0157 123 028
2
Heat shield small
0700 025 680
3
Heat shield
0366 960 016
4
Heat shield gas lens
0366 960 020
5
Heat shield large gas lens
0366 960 021
Collet standard and for gas lens,
short
0349 501 216
6
Ø 1.0
Ø 1.6
7
8
9
10
11
Ø 2.4
0349 501 218
Ø 3.2
0349 501 219
Ø 0.5
Collet standard and for gas lens
0157 123 009
Ø 1.0
0157 123 010
Ø 1.6
0157 123 011
Ø 2.0
0700 025 681
Ø 2.4
0157 123 012
Ø 3.0
0700 025 682
Ø 3.2
0157 123 013
Ø 4.0
0157 123 014
Ø 1.0-1.6
Collet body short
0700 025 683
Ø 2.0-2.4
0700 025 684
Ø 3.2
0700 025 685
Ø 1.0-1.6
Collet body with gas lens, short
0700 025 686
Ø 2.4
0700 025 687
Ø 3.2
0700 025 688
Ø 0.5-1.6
Collet body standard
0157 123 016
Ø 2.0-2.4
0157 123 017
Ø 3.0-3.2
0157 123 018
Ø 4.0
0157 123 019
Ø 1.0
Ø 1.6
0463 697 001
0349 501 217
Collet body with gas lens,
standard
0157 123 021
0157 123 022
Ø 2.0-2.4
0157 123 023
Ø 3.0-3.2
0157 123 024
Ø 4.0
0157 123 025
- 21 -
© ESAB AB 2019
WEAR PARTS
12
Ø 1.0
Ø 1.6
13
14
15
16
17
18
0463 697 001
Collet body with extra large gas
lens
0157 123 083
0157 123 084
Ø 2.0-2.4
0157 123 085
Ø 3.0-3.2
0157 123 086
Ø 4.0
0588 000 087
Ø 6.4 (No. 4)
Gas nozzle
0365 310 044
Ø 8.0 (No. 5)
L=30 mm
0365 310 045
Ø 9.8 (No. 6)
0365 310 046
Ø 11.2 (No. 7)
0365 310 047
Ø 12.7 (No. 8)
0365 310 048
Ø 15.9 (No. 10)
0588 000 440
Ø 6.4 (No. 4)
Gas nozzle for gas lens, short
0157 121 032
Ø 8.0 (No. 5)
L=25.5 mm
0157 121 033
Ø 9.8 (No. 6)
0157 121 034
Ø 11.2 (No. 7)
0157 121 039
Ø 12.7 (No. 8)
0157 121 040
Ø 6.4 (No. 4)
Gas nozzle standard
0157 123 052
Ø 8.0 (No. 5)
L=47 mm
0157 123 053
Ø 9.8 (No. 6)
0157 123 054
Ø 11.2 (No. 7)
0157 123 055
Ø 12.7 (No. 8)
0157 123 056
Ø 15.9 (No. 10)
0588 000 442
Ø 19 (No. 12)
0588 000 441
Ø 6.4 (No. 4)
Gas nozzle standard
0700 025 689
Ø 8.0 (No. 5)
L=76 mm
0700 025 690
Ø 9.8 (No. 6)
0700 025 691
Ø 11.2 (No. 7)
0700 025 692
Ø 6.4 (No. 4)
Gas nozzle for gas lens
0157 123 057
Ø 8.0 (No. 5)
L=42 mm
0157 123 058
Ø 9.8 (No. 6)
0157 123 059
Ø 11.2 (No. 7)
0157 123 060
Ø 12.7 (No. 8)
0157 123 061
Ø 17.5 (No. 11)
0588 000 439
Ø 6.4 (No. 4)
Gas nozzle for gas lens
0700 025 693
Ø 8.0 (No. 5)
L=76 mm
0700 025 694
Ø 9.8 (No. 6)
0700 025 695
Ø 11.2 (No. 7)
0700 025 696
Ø 12.7 (No. 8)
0700 025 697
- 22 -
© ESAB AB 2019
WEAR PARTS
19
20
Ø 9.8 (No. 6)
Gas nozzle for gas lens, large
0157 123 088
Ø 12.5 (No. 8)
L=48 mm
0157 123 089
Ø 15.9 (No. 10)
0588 000 438
Ø 19 (No. 12)
0157 123 098
Ø 24
0588 000 437
Ø 24
Gas nozzle for gas lens, short
0700 025 679
L=34 mm
0463 697 001
- 23 -
© ESAB AB 2019
WEAR PARTS
SR-B 400
Nozzles, collets, collet bodies and gas lenses:
Bold = standard delivery
Item
Size
Description
Ordering no.
1
Long
Back cap
0157 123 029
Medium
0588 000 591
Short
0157 123 028
2
3
4
5
Ø 1.0
Heat shield
0366 960 018
Collet standard and for gas lens
0157 123 010
Ø 1.6
0157 123 011
Ø 2.4
0157 123 012
Ø 3.2
0157 123 013
Ø 4.0
0157 123 014
Ø 2.4
Collet, heavy duty
Ø 3.2
0157 123 078
Ø 4.0
0157 123 079
Ø 4.8
0157 123 074
Ø 1.0-3.2
Collet body standard
Ø 3.2-4.8
6
7
Ø 1.0
0157 123 082
Collet body with gas lens
0157 123 091
0157 123 092
Ø 2.4
0157 123 093
Ø 3.2
0157 123 094
Ø 4.0
0157 123 095
Ø 4.8
0157 123 075
Ø 6.4 (No. 4)
Ø 9.8 (No. 6)
Gas nozzle standard and for gas
lens
L=42 mm
0157 123 057
0157 123 058
0157 123 059
Ø 11.2 (No. 7)
0157 123 060
Ø 12.7 (No. 8)
0157 123 061
Ø 17.5
0588 000 439
Ø 6.4 (No. 4)
Ø 8.0 (No. 5)
Ø 9.8 (No. 6)
0463 697 001
0157 123 081
Ø 1.6
Ø 8.0 (No. 5)
7
0157 123 077
Gas nozzle standard and for gas
lens
L=76 mm
0700 025 693
0700 025 694
0700 025 695
Ø 11.2 (No. 7)
0700 025 696
Ø 12.7 (No. 8)
0700 025 697
- 24 -
© ESAB AB 2019
WEAR PARTS
0463 697 001
- 25 -
© ESAB AB 2019
WEAR PARTS
XCT-B 400W
Nozzles, collets, collet bodies and gas lenses:
Bold = standard delivery
Item
Size
Description
Ordering no.
1
Long
Back cap
0700 025 650
Medium
0700 025 651
Short
0700 025 652
2
3
4
5
0463 697 001
Ø 1.6
Heat shield
0700 025 653
Collet standard
0700 025 654
Ø 2.4
0700 025 655
Ø 3.2
0700 025 656
Ø 4.0
0700 025 657
Ø 6.4 (No. 4)
Gas nozzle standard
0157 121 032
Ø 8.0 (No. 5)
L=25.5 mm
0157 121 033
Ø 9.8 (No. 6)
0157 121 034
Ø 11.2 (No. 7)
0157 121 039
Ø 12.7 (No. 8)
0157 121 040
Ø 6.4 (No. 4)
Gas nozzle standard
0700 025 658
Ø 8.0 (No. 5)
L=35.0 mm
0700 025 659
Ø 9.8 (No. 6)
0700 025 660
Ø 11.2 (No. 7)
0700 025 661
- 26 -
© ESAB AB 2019
WEAR PARTS
0463 697 001
- 27 -
© ESAB AB 2019
For contact information visit esab.com
ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00
http://manuals.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising