ESAB | WeldCloud™ Universal Connector | Instruction manual | ESAB WeldCloud™ Universal Connector User manual

ESAB WeldCloud™ Universal Connector User manual
WeldCloud™ Universal
Connector
Instruction manual
0463 601 001 US 20190328
Valid for: serial no. 849-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY .......................................................................................................
4
1.1
Meaning of symbols ...............................................................................
4
1.2
Safety precautions .................................................................................
4
INTRODUCTION ..........................................................................................
7
2.1
Equipment ...............................................................................................
7
2.2
Before setup of your WeldCloud™ Universal Connector...................
7
Charging the lithium-ion battery ...........................................................
7
3
TECHNICAL DATA ......................................................................................
8
4
INSTALLATION............................................................................................
9
4.1
Main components ...................................................................................
9
4.2
Inserting the lithium-ion battery into the electronics box ..................
9
4.3
Installing WeldCloud™ Universal Connector ......................................
10
Replacing the OKC connector ..............................................................
11
Setup of WeldCloud™ Universal Connector........................................
12
4.4.1
Downloading and installing the UCMon application .............................
12
4.4.2
Powering up the WeldCloud™ Universal Connector............................
13
4.4.3
Pairing the Android device to the WeldCloud™ Universal Connector..
13
4.4.4
14
4.4.6
Connecting the WeldCloud™ Universal Connector to a local Wi-Fi
network .................................................................................................
Connecting the WeldCloud™ Universal Connector to WeldCloud™
Cloud Platform......................................................................................
Changing the default name of the WeldCloud™ Universal Connector.
4.4.7
Setup additional weld parameters ........................................................
16
OPERATION ................................................................................................
18
5.1
Power supply ..........................................................................................
18
5.2
Operation modes ....................................................................................
18
5.3
Status indication LEDs ..........................................................................
18
5.4
Measuring and storing data...................................................................
20
MAINTENANCE ...........................................................................................
21
6.1
Inspection and cleaning.........................................................................
21
6.2
Validation ................................................................................................
21
6.3
Charging the lithium-ion battery ...........................................................
21
TROUBLESHOOTING .................................................................................
22
ORDERING SPARE PARTS ........................................................................
DIAGRAM ............................................................................................................
ORDERING NUMBERS .......................................................................................
WEAR PARTS......................................................................................................
ACCESSORIES ...................................................................................................
23
24
25
26
27
2
2.2.1
4.3.1
4.4
4.4.5
5
6
7
8
15
16
Rights reserved to alter specifications without notice.
0463 601 001
© ESAB AB 2019
1 SAFETY
1
SAFETY
1.1
Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer's safety practices and
Safety Data Sheets (SDSs).
1.2
Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed, in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations, which
could result in injury to the operator and damage to the equipment.
1.
2.
3.
Anyone who uses the equipment must be familiar with:
○ its operation
○ the location of emergency stops
○ its function
○ the relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
The operator must ensure that:
○ no unauthorized person is within the working area of the equipment when it is
started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
The workplace must:
○ be suitable for the purpose
○ be free from drafts
0463 601 001
-4-
© ESAB AB 2019
1 SAFETY
4.
5.
Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
• WeldCloud™ Universal Connector contains a lithium-ion battery (located in
the electronics box). Charging of the battery occurs during welding. If charging
of the battery is needed when no welding is performed, use the included
battery charger. Charging using any other type of charger may create a risk of
fire.
• When replacing the battery, only use a lithium-ion battery of the type specified
in the WEAR PARTS chapter of this manual. Using any other type of battery
may create a risk of injury and fire.
• If the battery is removed from the electronics box, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws or other small metal
objects that can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery. Avoid
contact with any liquid! If contact accidentally occurs, flush with water. If liquid
comes into contact with the eyes, seek additional medical help. Liquid ejected
from the battery may cause irritation or burns.
• Do not use a battery that is damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior resulting in fire, explosion or risk
of injury.
• Do not expose a battery to fire or excessive temperature. Exposure to fire or
temperature above +130 °C (+266 °F) may cause an explosion.
WARNING!
Do not connect the WeldCloud™ Universal Connector to a welding power source
used in MMA mode. It can trigger or activate welding mode.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be
potential difficulties in ensuring electromagnetic
compatibility of class A equipment in such locations,
due to conducted as well as radiated disturbances.
0463 601 001
-5-
© ESAB AB 2019
1 SAFETY
NOTE!
WeldCloud™ Universal Connector is intended for maximum 15 kV HF peak ignition
voltage in TIG welding. 15 kV is maximum peak ignition voltage in standard welding
power sources of today. In older welding power sources, the maximum peak ignition
voltage sometimes can be higher.
NOTE!
Dispose of electronic equipment at a recycling
facility!
To conform with the European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law,
electrical and/or electronic equipment that has reached
the end of its life must be disposed of at a recycling
facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved
collection stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information, contact your local ESAB dealer or visit us on
our website.
0463 601 001
-6-
© ESAB AB 2019
2 INTRODUCTION
2
INTRODUCTION
WeldCloud™ Universal Connector is a brand-agnostic welding measurement system used to
enable data collection of any welding power source (ESAB made or numerous other welding
power sources on the market). The welding current and welding voltage are measured and
the collected data is sent to the WeldCloud™ cloud via Wi-Fi and the local network.
To install WeldCloud™ Universal Connector, access to WeldCloud™ web service is required.
Register for a username and password to be able to access your WeldCloud™ account.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1
Equipment
WeldCloud™ Universal Connector is supplied with:
•
•
•
•
•
Instruction manual
Ratchet straps for attachment of the sensor box
Two additional OKC connectors (95 mm)
Lithium-ion battery
Battery charger for lithium-ion battery
2.2
Before setup of your WeldCloud™ Universal Connector
In order to complete the setup of the WeldCloud™ Universal Connector, the following is
needed:
•
•
•
•
An Android device with operating system 6.0 or greater (recommended minimum
screen size 4.7")
A torx screwdriver size T10
Installed WeldCloud™ software
A fully charged lithium-ion battery (see below)
2.2.1
1.
2.
Charging the lithium-ion battery
Insert the lithium-ion battery into the battery charger included in the delivery.
Charge the lithium-ion battery for at least 24 hours.
0463 601 001
-7-
© ESAB AB 2019
3 TECHNICAL DATA
3
TECHNICAL DATA
WeldCloud™ Universal Connector, Valid from serial no. 849-xxx-xxxx
Permissible load (I2):
60% duty cycle
500 A
100% duty cycle
400 A
MIG
15 A / 14.8 V to 500 A / 39 V
TIG HF
15 A / 10.6 V to 500 A / 30 V
U1
10-100 V
Current and power at U1 = 30 V:
I1
0.3 A
Pmax
9W
Measurement accuracy (regarding measured
current and voltage)
±2%
Operating temperature
-10 to +40 °C (+14 to +104 °F)
Battery data:
Technology
Lithium-ion battery
Nominal voltage
3.7 V (±0.1 V)
Rated Capacity
2200 mAh
Storage temperature
-4 to +140 °F (-20 to +60 °C)
Charging temperature
+5 to +40 °C (+41 to +104 °F)
Dimensions (l × w × h):
Sensor box
12.5 × 9.2 × 2.9 in (318 × 234 × 74 mm)
Electronics box
9.4 × 5.8 × 1.6 in (238 × 147 × 40 mm)
Weight:
Sensor box
4.4 lb (2.0 kg)
Electronics box
1.5 lb (0.7 kg)
Total including cables
15.4 lb (7 kg)
Enclosure class
IP43
Application class
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP43 is intended for indoor and outdoor use; however, should not be
operated in precipitation unless sheltered.
0463 601 001
-8-
© ESAB AB 2019
4 INSTALLATION
4
INSTALLATION
The installation must be carried out by a professional.
CAUTION!
This product is intended for industrial use. In a domestic environment, this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
WARNING!
Assure cables make full contact!
4.1
Main components
1. Sensor box
2. Electronics box
4. Connection to welding circuit
5. Push button (to power up, shut down and
restart the WeldCloud™ Universal
Connector)
3. Connection to welding output terminals
on the power source
4.2
1.
2.
Inserting the lithium-ion battery into the electronics box
Make sure the lithium-ion battery is fully charged.
Loosen the two screws at the back of the electronics box. Remove the battery lid.
0463 601 001
-9-
© ESAB AB 2019
4 INSTALLATION
3.
Insert the lithium-ion battery. Attach the battery lid and the screws in reverse order.
Tightening torque 0.6 Nm.
4.3
1.
Installing WeldCloud™ Universal Connector
Attach the electronics box in a suitable position on the welding equipment, using
Velcro® tape on the back of the electronics box.
NOTE!
The electronics box contains a radio transmitter and receiver. Position it as
high as possible on the welding equipment.
a)
b)
2.
Use alcohol to clean the area where the Velcro® tape is to be attached.
Remove the protection cover of the Velcro® tape and attach the electronics
box.
Once the adhesive tape on the back of the Velcro® tape is fastened to the welding
equipment, the electronics box can easily be attached and detached multiple times.
Connect the sensor box to the power source welding output terminals. It does not
matter which connector is connected to the + terminal and which is connected to the
- terminal of the power source.
If the power source doesn't have OKC connectors, disassemble the OKC connectors
from the sensor box cables and replace them with the appropriate type of connector.
WARNING!
The plugs may only be replaced by a specialist and must comply with the
applicable standards for welding current connections. The plugs and sockets
must be suitable for a 400-A continuous current or 500 A at 60% duty cycle.
Connecting non-permissible contact elements or improper installation can
lead to heating, cable fires and further consequential damage.
This will void the warranty.
3.
Connect the torch and the work lead to the sensor box, ensure the correct polarity
(with respect to the welding output terminals) depending on the welding method used.
Examples of how to position the electronics box and the sensor box on the welding
equipment. In the first case, the ratchet straps included in the delivery are used to attach the
sensor box to the trolley.
0463 601 001
- 10 -
© ESAB AB 2019
4 INSTALLATION
NOTE!
To ensure ingress protection (IP) of the WeldCloud™ Universal Connector, the
sensor box and the electronics box must be positioned according to one of the
alternatives below.
NOTE!
If the WeldCloud™ Universal Connector is used together with a power source with a
Voltage Reduction Device (VRD), check that VRD functionality is maintained after
the installation!
4.3.1
Replacing the OKC connector
CAUTION!
The connectors can cause burn injuries.
It is required to replace the non-ESAB cables with the provided OKC connectors if any of the
following conditions occur:
•
•
•
The connections to the welding output terminals on the power source are not secure.
The connector is damaged.
The rubber surface of the connector is very hot.
0463 601 001
- 11 -
© ESAB AB 2019
4 INSTALLATION
1.
2.
3.
4.
Pull the rubber housing (1) off the brass connector.
Remove the Allen screws from the brass connector (2).
Remove the brass connector from the cable wiring (3).
If the cable wire shroud (4) is damaged or missing, add the provided cable wire
shroud. Insert the cable wire with the cable wire shroud into the provided brass
connector (5).
Tighten the Allen screws to fasten the cable wire in the brass connector (6). Tighten
the Allen screws to be aligned with or below the surface of the brass connector.
Pull the rubber housing back (7) until it completely covers the brass connector (5).
5.
6.
4.4
Setup of WeldCloud™ Universal Connector
After the physical installation of WeldCloud™ Universal Connector is completed, software
setup of the system must be performed. The software setup includes the following main
activities:
•
•
•
•
•
Downloading and installing the UCMon application to the Android device. (Operating
system 6.0 or greater, recommended minimum screen size 4.7".)
Powering up the WeldCloud™ Universal Connector
Pairing the Android device to the WeldCloud™ Universal Connector
Connecting the WeldCloud™ Universal Connector to the local Wi-Fi network
Connecting the WeldCloud™ Universal Connector to WeldCloud™ Cloud Platform
Each activity is explained below.
4.4.1
1.
2.
Downloading and installing the UCMon application
Download the latest software version of the Android application "UCMon" from Google
Play.
Install the UCMon application on the preferred Android device.
0463 601 001
- 12 -
© ESAB AB 2019
4 INSTALLATION
4.4.2
1.
Powering up the WeldCloud™ Universal Connector
Initiate the WeldCloud™ Universal Connector by pressing the push
button on the right side of the signal cable inlet on the electronics
box.
A steady green power LED on the electronics box indicates that the
WeldCloud™ Universal Connector is on. This takes approximately 20
seconds.
4.4.3
1.
2.
Pairing the Android device to the WeldCloud™ Universal Connector
Enable Bluetooth on the Android device.
Start the UCMon application on the Android device.
On start up the application shows a list of all known WeldCloud™ Universal
Connectors. For each WeldCloud™ Universal Connector found, the name and the
MAC address is displayed.
If the correct WeldCloud™ Universal Connector is not present in the list, click
Discover beneath the list to perform a new search.
3.
Choose the desired device from the list and click Connect to connect to the
WeldCloud™ Universal Connector.
The Android device is now paired and connected to the WeldCloud™ Universal
Connector.
NOTE!
A device which has not been configured is named after its
Bluetooth MAC address, which can be found in the box.
On successful pairing, the application automatically displays the Measuring screen that
shows live data from the sensor. Click the cogwheel in the upper right corner to switch
between monitoring and configuration mode.
0463 601 001
- 13 -
© ESAB AB 2019
4 INSTALLATION
A steady blue Bluetooth LED on the electronics box confirms the connection
to the WeldCloud™ Universal Connector.
Previously paired devices will be shown separately in the list of devices.
4.4.4
1.
Connecting the WeldCloud™ Universal Connector to a local Wi-Fi
network
2.
Click Config at the bottom of the screen in the UCMon application.
If requested, enter the password to access the Config menu. The default password is
Esab.
Click in the edit box Name (SSID) or Password in the Wi-Fi section.
3.
Enter the local Wi-Fi name and password.
4.
5.
Click Send in the Wi-Fi section.
The Wi-Fi symbol in the header indicates that the local Wi-Fi connection has been
established. The Host IP of the WeldCloud™ Universal Connector is displayed. To
connect the WeldCloud™ Universal Connector to a local Wi-Fi takes approximately 15
seconds.
0463 601 001
- 14 -
© ESAB AB 2019
4 INSTALLATION
4.4.5
Connecting the WeldCloud™ Universal Connector to WeldCloud™ Cloud
Platform
NOTE!
Changes may apply. Refer to the WeldCloud™ manual for updated instructions.
1.
To create a new asset in the WeldCloud™ web portal select the Asset Type » Weld
Azure Power Source Thing template and define the Asset Name.
2.
Click Download certificates bundle to download the configuration file. Save the file in
the Android device Download folder.
3.
Pair the desired WeldCloud™ Universal Connector, see chapter "Pairing the Android
device to the WeldCloud™ Universal Connector".
Ensure that a Wi-Fi connection is established, see chapter "Connecting the
WeldCloud™ Universal Connector to a local Wi-Fi network".
Click Cloud.
Click File... in the next screen to select a provisioning file to connect to WeldCloud™
cloud.
4.
5.
6.
7.
Choose the downloaded provisioning file from the list and click Accept.
0463 601 001
- 15 -
© ESAB AB 2019
4 INSTALLATION
8.
Click Execute to establish the connection to WeldCloud™ cloud. The information in
the cloud is updated when the connection is established. The cloud symbol in the
header indicates the WeldCloud™ connection.
The name of the WeldCloud™ Universal Connector will automatically be set to the
name of the asset in WeldCloud™.
9.
For security reasons it is recommended to delete the configuration file from the
Android device when the procedure is complete.
4.4.6
Changing the default name of the WeldCloud™ Universal Connector
NOTE!
The name of the WeldCloud™ Universal Connector is taken from the asset when the
connection to WeldCloud™ cloud is configured.
The name of the WeldCloud™ Universal Connector is the same as the name of the
asset in the WeldCloud™. Renaming the WeldCloud™ Universal Connector only
affects the Bluetooth connection, the name in WeldCloud™ is retained.
1.
2.
3.
In the lower right part of the
screen click Config.
If requested, enter the
password to access the Config
menu. The default password is
Esab.
Click on the edit box of the
WeldCloud™ Universal
Connector name.
Enter a new name for the
device. Click Send.
4.4.7
Setup additional weld parameters
1.
To add/edit additional weld parameters (wire, gas or operator), click the scan button.
2.
Scan the parameter code (Code 128, QR-Code).
0463 601 001
- 16 -
© ESAB AB 2019
4 INSTALLATION
3.
4.
Click Apply next to the field of the type of parameter that has been scanned.
The additional weld parameters are bundled together with each weld seam and sent
to WeldCloud™.
0463 601 001
- 17 -
© ESAB AB 2019
5 OPERATION
5
OPERATION
5.1
Power supply
The WeldCloud™ Universal Connector is powered from the welding circuit during welding.
There is no need for external power supply to the unit.
The WeldCloud™ Universal Connector has a lithium-ion battery as backup power when no
welding is conducted. The lithium-ion battery is charged during welding.
5.2
Operation modes
The WeldCloud™ Universal Connector has three operation modes:
•
•
•
System off
Data collection is off. The system will start up at weld start or when the push button on
the sensor box is pressed. Start-up takes approximately 20 seconds, during this time
no welding data is collected.
Sleep mode
Battery saving mode. The system will reboot at weld start. The reboot takes
approximately 1 second, during this short time no welding data is collected. If no
welding is detected after 2 hours, the system will shut down automatically.
System on
The system is capable of data collection. Weld start detection takes approximately 1
second, during this short time no welding data is collected. If no welding is detected
after 60 seconds, the system goes to sleep.
The WeldCloud™ Universal Connector can always be turned on or off manually by the push
button on the sensor box.
5.3
Status indication LEDs
Four status indication LEDs (Light Emitting Diodes) are located on the electronics box.
1. Battery LED
2. Power LED
0463 601 001
3. Bluetooth LED
4. Wi-Fi LED
- 18 -
© ESAB AB 2019
5 OPERATION
1. Battery LED
Indication
Explanation
System is Off or in Sleep mode
Flashing green
Charging
Steady red
Low battery
Steady green
Charging complete
Steady orange
No longer charging
Quick red flashing
Battery missing or faulty, or battery has stopped
charging
2. Power LED
Indication
Explanation
Off
System off
Flashing green
Starting up
Steady green
System on or sleep mode
Steady orange
Welding ongoing
3. Bluetooth LED
Indication
Explanation
Off
Bluetooth off, no connection possible
Quick blue flash every 5 seconds
Ready for pairing
0463 601 001
- 19 -
© ESAB AB 2019
5 OPERATION
Indication
Explanation
Steady blue
Connected
Flashing blue
Connected and being configured. The time until the
system goes to sleep is extended
4. Wi-Fi LED
Indication
Explanation
Off
Wi-Fi off, no connection possible
Flashing white
System connected to the local Wi-Fi network but not to
WeldCloud™ cloud.
Quick white flash every 5 seconds System ready but not connected to the local Wi-Fi
network. (Configuration not correct or Wi-Fi point
unavailable.)
Steady white
5.4
System connected to the local Wi-Fi network and to
WeldCloud™ cloud.
Measuring and storing data
The WeldCloud™ Universal Connector measures the absolute average values of the welding
current and the welding voltage. The data is collected at high-speed sampling rate. The data
is averaged to limit the amount of data sent to the WeldCloud™ cloud.
The amount of data created and stored with each weld is dependent on:
•
•
The welding time
The amount of information entered into the system prior to welding
After each weld, the data is automatically sent to the WeldCloud™ cloud. If the connection to
the cloud is lost, the data is internally stored in the WeldCloud™ Universal Connector. The
capacity is up to 1000 weld seams of 10 seconds, i.e. longer weld seams will result in fewer
stored weld seams. If the system is reconnected, the internally stored data is automatically
sent to the WeldCloud™ cloud.
NOTE!
The current must drop below 15 A for at least 1 second to stop recording.
0463 601 001
- 20 -
© ESAB AB 2019
6 MAINTENANCE
6
MAINTENANCE
NOTE!
Regular maintenance is important for safe and reliable operation.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer attempts
any work to rectify any faults in the product during the warranty period.
6.1
Inspection and cleaning
When needed, clean the dust off boxes, cables and connectors included in the WeldCloud™
Universal Connector system using a dry cloth, according to standard workshop practices.
6.2
Validation
It is recommended to periodically validate the accuracy of the external sensor. The validation
can be coordinated with the user's validation of welding equipment in general. If accuracy is
found to be out of tolerance, contact an authorized ESAB distributor or service center for
further assistance.
6.3
Charging the lithium-ion battery
Normally charging of the lithium-ion battery in the electronics box occurs during welding. If
charging of the lithium-ion battery is needed when no welding is performed, it can be
removed from the electronics box and charged in a separate battery charger. Use a charger
of the L1 type intended for lithium-ion batteries of the 18650 type. Only use chargers with
CCCV (constant current, constant voltage) characteristics. Do not charge more than 4.2 V.
Charging using any other type of charger creates a risk of fire.
If the WeldCloud™ Universal Connector is to be stored, make sure that the lithium-ion
battery is fully charged. For a longer storage period, remove the lithium-ion battery from the
electronics box! Before reusing the WeldCloud™ Universal Connector, charge the lithium-ion
battery using the included battery charger.
0463 601 001
- 21 -
© ESAB AB 2019
7 TROUBLESHOOTING
7
TROUBLESHOOTING
Try these recommended checks and inspections before sending for an authorized service
technician.
Type of fault
Corrective action
The battery LED on the electronics box is not
lit or is flashing red, despite the fact that
welding is going on.
The WeldCloud™ Universal Connector has
got no power or the battery is low.
Use the charger included and charge the
lithium-ion battery for a minimum of 24 hours
or replace it with a fully charged spare
lithium-ion battery.
The welding power source is not turned on
and nothing happens when the push button
(on the electronics box) is pressed.
Use the included charger and charge the
lithium-ion battery or replace it with a fully
charged spare lithium-ion battery.
There is no data for the specific
WeldCloud™ Universal Connector visible in
the WeldCloud™ software.
Check the power LED on the electronics box.
The power LED should be on with a steady
green light. If the power LED is off or is
flashing green, power up the WeldCloud™
Universal Connector (by pushing the button)
and wait until it has entered ready mode
(steady green power LED).
Check the Wi-Fi LED on the electronics box.
The Wi-Fi LED should be on with a steady
white light. If the Wi-Fi LED is quickly flashing
white every 5 seconds, connect the
WeldCloud™ Universal Connector to the
local Wi-Fi network. If the Wi-Fi LED is
flashing steadily in white, connect the
WeldCloud™ Universal Connector to
WeldCloud™ cloud.
The welding power source shows
Contact your welding power source supplier
unexpected error messages or performs
and ask for advice.
unintended actions when it is connected to
the WeldCloud™ Universal Connector.
Some modern welding power sources
operating in MMA (stick) mode have sensitive
safety protection circuits that can be
disturbed by the WeldCloud™ Universal
Connector.
The OKC connector rubber surface is hot.
Check if the cable connection is tight. Make
sure that the cable connection makes full
contact. Twist the male and female OKC
connector ends until they lock together.
Replace the male connector with the male
OKC connector provided. See the Replacing
the OKC connector section in this manual.
0463 601 001
- 22 -
© ESAB AB 2019
8 ORDERING SPARE PARTS
8
ORDERING SPARE PARTS
WeldCloud™ Universal Connector is designed and tested in accordance with the
international and European standards IEC/EN 60974-1 and IEC/EN 60974-10 Class A. It is
the obligation of the service unit which has carried out the service or repair work to make
sure that the product still conforms to the mentioned standards.
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see the back
cover of this document. When ordering, please state product type, serial number, designation
and spare part number in accordance with the spare parts list. This facilitates dispatch and
ensures correct delivery.
0463 601 001
- 23 -
© ESAB AB 2019
DIAGRAM
DIAGRAM
0463 601 001
- 24 -
© ESAB AB 2019
ORDERING NUMBERS
ORDERING NUMBERS
Ordering number Denomination
Type
0445 690 880
WeldCloud™ Universal Connector
Basic
0463 602 001
Service manual
WeldCloud™ Universal Connector
0463 603 001
Spare parts list
WeldCloud™ Universal Connector
0463 601 001
- 25 -
© ESAB AB 2019
WEAR PARTS
WEAR PARTS
Ordering number Denomination
Notes
0194 008 101
Lithium Coin Cell Battery
3 V, 225 mAh
0445 670 001
Lithium-ion battery
Type 18650
0463 601 001
- 26 -
© ESAB AB 2019
ACCESSORIES
ACCESSORIES
0160 360 882
OKC 95 male cable connection (4 pieces)
0160 361 882
OKC 95 female cable connection (4 pieces)
0365 557 001
Angle connection, 1 male, 2 female
0365 558 001
Angle connection, 2 male, 1 female
0700 006 899
Return cable, 3 metres, OKC 50
0463 601 001
- 27 -
© ESAB AB 2019
For contact information visit esab.com
ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00
http://manuals.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising