ESAB | Mig U5000i | Instruction manual | ESAB Mig U5000i User manual

ESAB Mig U5000i User manual
Aristo®
Mig U5000i,
Mig U5000i WeldCloud™
400 V
Instruction manual
0459 291 601 GB 20181030
Valid for: serial no. 834-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY .......................................................................................................
5
1.1
Meaning of symbols ...............................................................................
5
1.2
Safety precautions .................................................................................
5
INTRODUCTION ..........................................................................................
8
2.1
Equipment ...............................................................................................
8
3
TECHNICAL DATA ......................................................................................
9
4
INSTALLATION............................................................................................
11
4.1
Lifting instructions .................................................................................
11
4.2
Placing.....................................................................................................
11
4.3
Mains power supply ...............................................................................
11
4.4
Terminating resistor ...............................................................................
12
4.5
Connection of multiple wire feed units ................................................
12
OPERATION ................................................................................................
14
5.1
Connections and control devices .........................................................
15
5.2
Turning on the power source ................................................................
16
5.3
Fan control ..............................................................................................
16
5.4
Overheating protection ..........................................................................
16
5.5
Cooling unit.............................................................................................
16
5.6
Remote control unit................................................................................
17
5.7
WeldCloud™ unit....................................................................................
17
MAINTENANCE ...........................................................................................
18
6.1
Daily .........................................................................................................
18
6.2
If necessary.............................................................................................
18
6.3
Every year ...............................................................................................
19
FAULT TRACING.........................................................................................
20
ORDERING SPARE PARTS ........................................................................
DIAGRAM ............................................................................................................
ORDERING NUMBERS .......................................................................................
SPARE PARTS LIST............................................................................................
ACCESSORIES ...................................................................................................
21
22
24
25
26
2
5
6
7
8
Rights reserved to alter specifications without notice.
0459 291 601
© ESAB AB 2018
1 SAFETY
1
SAFETY
1.1
Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2
Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1.
2.
3.
Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
The workplace must:
○ be suitable for the purpose
○ be free from drafts
0459 291 601
-5-
© ESAB AB 2018
1 SAFETY
4.
5.
Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
•
•
•
•
Install and ground the unit in accordance with instruction manual.
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
Insulate yourself from work and ground.
Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
•
•
•
Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
Exposure to EMF may have other health effects which are unknown.
Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or work
cable around your body. Keep welding power source and cables as
far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
•
•
Keep your head out of the fumes.
Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
•
•
Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
0459 291 601
-6-
© ESAB AB 2018
1 SAFETY
MOVING PARTS - Can cause injuries
•
•
•
Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
Stop engine before installing or connecting unit.
Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
•
•
Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment and its implementation
in accordance with national law, electrical and/or electronic
equipment that has reached the end of its life must be
disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
0459 291 601
-7-
© ESAB AB 2018
2 INTRODUCTION
2
INTRODUCTION
The Mig U5000i is a MIG/MAG and TIG welding power source, which can also be used for
MMA welding.
There are two variants of the power source:
•
•
Mig U5000iw with cooling unit
Mig U5000iw with cooling unit and WeldCloud™ unit
The power source is intended for use with the Feed 3004 or Feed 4804 wire feed units.
All the settings are made from the wire feed unit or control box.
The power source Mig U5000i WeldCloud™ is combined with U82 and provides a control
box which enables wireless monitoring.
For more information about the feed units and WeldCloud™, refer to the Instruction manuals.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1
Equipment
The power source is supplied complete with terminating resistor, 5m return cable and
instruction manual.
0459 291 601
-8-
© ESAB AB 2018
3 TECHNICAL DATA
3
TECHNICAL DATA
Mig U5000i
Mig U5000i WeldCloud™
Mains voltage
400 V ±10%, 3~ 50/60 Hz
400 V ±10%, 3~ 50/60 Hz
Mains supply
Sscmin 8.7 MVA
Zmax 0.018 Ω
Sscmin 8.7 MVA
Zmax 0.018 Ω
Imax MIG/MAG (GMAW)
33 A
33 A
Imax MMA (SMAW)
34 A
34 A
Imax TIG (GTAW)
26 A
26 A
Primary current
No-load power demand when in energy-saving mode, 6.5 min. after welding
TIG/MIG (GTAW/GMAW)
45 W
45 W
MMA (SMAW)
55 W
55 W
MIG/MAG (GMAW)
8 - 60 V / 16 - 500 A
8 - 60 V / 16 - 500 A
MMA (SMAW)
16 - 500 A
16 - 500 A
TIG (GTAW)
4 - 500 A
4 - 500 A
Voltage/current range
Permissible load at MIG/MAG (GMAW)
60 % duty cycle
500 A / 39 V
500 A / 39 V
100 % duty cycle
400 A / 34 V
400 A / 34 V
Permissible load at MMA (SMAW)
60 % duty cycle
500 A / 40 V
500 A / 40 V
100 % duty cycle
400 A / 36 V
400 A / 36 V
Permissible load at TIG (GTAW)
60 % duty cycle
500 A / 30 V
500 A / 30 V
100 % duty cycle
400 A / 26 V
400 A / 26 V
Power factor at maximum current (I2)
MMA
0.91
0.91
TIG
0.90
0.90
MIG
0.90
0.90
Efficiency at maximum current (I2)
MMA
87 %
87 %
TIG
82 %
82 %
MIG
83 %
83 %
1)
72 - 88 V
72 - 88 V
MMA (SMAW) without VRD
function 1)
68 - 80 V
68 - 80 V
Open-circuit voltage U0 max
MIG/MAG (GMAW), TIG
(GTAW) without VRD function
0459 291 601
-9-
© ESAB AB 2018
3 TECHNICAL DATA
Mig U5000i
U0L "Live TIG (GTAW)", VRD 79 V
function deactivated
Mig U5000i WeldCloud™
79 V
2)
MIG/MAG (GMAW), MMA
(SMAW), VRD function
deactivated 2)
59 V
59 V
VRD function activated 2)
< 35 V
< 35 V
Operating temperature
-10 to +40 °C
(14 to 104 °F)
-10 to +40 °C
(14 to 104 °F)
Transportation temperature -20 to +55 °C
(-4 to 131 °F)
-20 to +55 °C
(-4 to 131 °F)
Dimensions l × w × h
without cooling unit
625 × 394 × 496 mm
(24.6 × 15.5 × 19.5 in.)
625 × 394 × 496 mm
(24.6 × 15.5 × 19.5 in.)
with cooling unit
625 × 394 × 776 mm
(24.6 × 15.5 × 30.6 in.)
625 × 394 × 776 mm
(24.6 × 15.5 × 30.6 in.)
Continual sound pressure
at no-load
<70 db (A)
<70 db (A)
Weight
without cooling unit
71 kg (159 lb)
82 kg (183 lb)
91 kg (200 lb)
102 kg (225 lb)
with cooling unit
Insulation class transformer H
H
Enclosure class
IP23
IP23
Application class
1)
Valid for power sources without VRD specification on the rating plate.
2)
Valid for power sources with VRD specification on the rating plate. The VRD function is
explained in the instruction manual for the control panel.
0459 291 601
- 10 -
© ESAB AB 2018
4 INSTALLATION
4
INSTALLATION
The installation must be carried out by a professional.
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the user's
supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to Sscmin. Refer to the technical data in the
TECHNICAL DATA chapter.
4.1
Lifting instructions
Power source
4.2
Trolley and power source
Trolley 2 and power source
Placing
Position the welding power source such that its cooling air inlets and outlets are not
obstructed.
4.3
Mains power supply
Check that the unit is connected to the correct mains power supply
voltage, and that it is protected by the correct fuse sizes. A protective
earth connection must be made, in accordance with regulations.
Rating plate with supply connection data
0459 291 601
- 11 -
© ESAB AB 2018
4 INSTALLATION
Recommended fuse sizes and minimum cable areas
Mig U5000i
400 V 3~ 50 Hz
Mains voltage
400 V
Mains cable area, mm2
4G6
Phase current, I1eff
28 A
Fuse
Anti-surge
25 A
Type C MCB
32 A
NOTE!
The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. For other regions, supply cables must be suitable for the
application and meet local and national regulations.
4.4
Terminating resistor
In order to avoid communication interference, the ends of the
CAN bus must be fitted with terminating resistors.
One end of the CAN bus is at the control panel, which has an
integral terminating resistor. The other end at the power
source must be fitted with the terminating resistor, as shown
on the right.
4.5
Connection of multiple wire feed units
With control unit and wire feed units without control panel it is possible to manage up to 4
wire feed units from one power source.
It is possible to choose between the following connections:
•
•
•
•
1 TIG torch and 1 MIG gun (Universal power source required)
2 MIG/MAG guns
1 TIG torch and 3 MIG guns (Universal power source required)
4 MIG guns
When welding with water-cooled MIG gund on all wire feed units, it is recommended to
connect a separate cooling unit for the 2 extra guns.
We recommend connecting the guns in parallel.
Two wire feed units
A connection kit is required when connecting two wire feed units, see chapter
"ACCESSORIES".
0459 291 601
- 12 -
© ESAB AB 2018
4 INSTALLATION
A. Water connection
B. Welding current connection
C. Control box connection
Four wire feed units
Two connection kits and an extra cooling unit are required when connecting four wire feed
units, see chapter "ACCESSORIES".
A. Water connection
B. Welding current connection
C. Control box connection
0459 291 601
- 13 -
© ESAB AB 2018
5 OPERATION
5
OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
0459 291 601
- 14 -
© ESAB AB 2018
5 OPERATION
5.1
Connections and control devices
1
Orange indicating lamp - Overheating
14* *Only on WeldCloud™ version: Red
indicating lamp - Wi-Fi Connectivity
2
White indicating lamp - Power supply ON 15 Fuse for supply voltage for feeder unit,
42 V
3
Mains power supply switch, 0 / 1 /
START
4
Connection for start signal from the torch 17* *Only on WeldCloud™ version: Measure
outlet screw terminal Red (+)
5
Connection for gas to the TIG torch
6
Connection (-) for return cable at MMA or 19 Connection for control cable to the wire
for welding current cable at TIG welding
feed unit or to the terminating resistor
7
Connection for remote control
8
Connection (+) for welding current cable 21 Connection for gas hose
at MMA welding or for return cable at
TIG welding
9
Cooling water filler
16* *Only on WeldCloud™ version:
Connection for Ethernet
18* *Only on WeldCloud™ version: Measure
outlet screw terminal Black (-)
20 Connection for control cable to the wire
feed unit or for the terminating resistor
22 Connection (+) for welding current cable
to the wire feed unit (MIG/MAG)
10 Connection with ELP1 for cooling water
to the TIG torch - BLUE
23 Connection (-) for the return cable
(MIG/MAG)
11 Connection for cooling water from the
TIG torch - RED
24 Connection for cooling water to the wire
feed unit - BLUE
12* *Only on WeldCloud™ version: Antenna 25 Connection for cooling water from the
wire feed unit - RED
13* *Only on WeldCloud™ version: USB
Connectivity
1)
ELP = ESAB Logic Pump, see section "Cooling unit" in this chapter.
0459 291 601
- 15 -
© ESAB AB 2018
5 OPERATION
5.2
Turning on the power source
Turn on the mains power by turning switch (7) to the ”START” position. Release the switch,
and it will return to the ”1” position.
If the mains power supply should be interrupted while welding is in progress, and then be
restored, the power source will remain de-energised until the switch is again turned manually
to the ”START” position.
Turn the unit off by turning the switch to the ”0” position.
Whether in the event of a loss of power supply or of turning the power source off in the
normal manner, welding data will be stored so that it is available next time the unit is started.
5.3
Fan control
The power source fans continue to run for 6.5 minutes after welding has stopped, and the
unit switches to energy-saving mode. They start again when welding restarts.
The fans run at reduced speed for welding currents up to 180 A, and at full speed for higher
currents.
5.4
Overheating protection
The power source has two thermal overload trips which operate if the internal temperature
becomes too high, interrupting the welding current and lighting the orange indicating lamp on
the front of the unit. They reset automatically when the temperature has fallen.
5.5
Cooling unit
To ensure problem-free operation, the installation height from the cooling unit to the welding
torch must be max. 7 m. Heights in excess of this can cause problems, such as long starting
times, air bubbles, vacuums, etc.
If an installation height in excess of 7 m is required, we recommend an installation kit
comprising a non-return valve and a solenoid valve, refer to chapter "ACCESSORIES". Once
these valves have been installed, the hose package must be horizontal during the initial
startup so that everything fills with water. Then raise the wire feed unit and hose package to
the high height. Continued safe operation at installation heights of up to 12 m can now
commence.
Water connection (TIG welding)
The cooling unit is equipped with a detection system ELP (ESAB Logic Pump) which checks
that the water hoses are connected.
The power source On/Off switch must be in the “0” position (Off) when connecting a
water-cooled TIG torch.
If a water-cooled TIG torch is connected, the water pump starts automatically when the main
On/Off switch is turned to ”START” and/or when welding starts. After welding, the pump
continues to run for 6.5 minutes, and then switches to the energy-saving mode.
Function when welding
To start welding, the welder presses the welding torch trigger switch. The power source turns
on and starts the wire feed and the cooling water pump.
To stop welding, the welder releases the welding torch trigger switch. Welding ceases, but
the cooling water pump continues to run for 6.5 minutes, after which the unit switches to
energy-saving mode.
Water flow guard
The water flow guard interrupts the welding current in the event of loss of coolant, and
displays an error message on the control panel. The water flow guard is an accessory.
0459 291 601
- 16 -
© ESAB AB 2018
5 OPERATION
5.6
Remote control unit
When the remote control unit is connected, the power source and wire feed unit are in
remote control mode; the buttons and knobs are blocked. The functions can only be adjusted
via the remote unit.
If the remote control unit is not to be used, the remote control unit must be disconnected from
the power source / wire feed unit, as otherwise it will remain in remote control mode.
For more information about the operation of the remote control unit, see the operating
instructions for the control panel.
5.7
WeldCloud™ unit
The WeldCloud™ unit connects the welding power source with a local WeldCloud™ server
through Wi-Fi or Wired LAN. The WeldCloud™ unit is equipped with GPS to track the
location of the welding power source. It also has Bluetooth connectivity to enable connection
with 3rd party input devices, for example a Bluetooth enabled barcode/QR scanner.
The WeldCloud™ unit Wi-Fi is enabled at power up of the power source. It will start as a
hotspot that appears as an available Wi-Fi network. After establishing connection, it is
possible to access the web interface of the power source for a one-time set-up. After set-up
and restart, the power source will be visible in WeldCloud™. For more information about the
WeldCloud™ unit and features, see the WeldCloud™ instruction manual.
0459 291 601
- 17 -
© ESAB AB 2018
6 MAINTENANCE
6
MAINTENANCE
NOTE!
Regular maintenance is important for safe and reliable operation.
Only those persons who have appropriate electrical knowledge (authorised personnel) may
remove the safety plates to connect or carry out service, maintenance or repair work on
welding equipment.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.1
Daily
Carry out the following maintenance every day.
•
•
Check that all cables and connections are fault free. Tighten if necessary and replace
any defective parts.
Check the water level and water flow, top up with coolant if necessary.
6.2
•
•
If necessary
Regularly check that the power source is not clogged with dirt.
Clogged or blocked air inlets and outlets result in overheating.
Clean the dust filter.
•
•
•
•
•
•
•
Remove the fan grille with the dust
filter (1).
Swing out the grille (2).
Release the dust filter (3).
Blow the filter clean with
compressed air (reduced pressure).
Replace the filter with the finer mesh
on the side against the grille (2) (out
from the power source).
Replace the fan grille with the dust
filter.
Top up with coolant
ESAB's ready mixed coolant is recommended for use. See
chapter "ACCESSORIES".
•
Top up with coolant until it covers half the inlet pipe.
NOTE!
Coolant must be topped up if connecting a welding torch or
connection cables that are 5 m in length or longer. When
adjusting the water level by topping up, the coolant hose
does not need to be disconnected.
CAUTION!
The coolant must be handled as chemical waste.
0459 291 601
- 18 -
© ESAB AB 2018
6 MAINTENANCE
6.3
Every year
Carry out the following maintenance at least once a year.
•
•
•
Clean off any dirt and dust. Blow the power source clean with dry compressed air
(reduced pressure).
Change the coolant and clean the hoses and water reservoir with clean water.
Check seals, cables and connections. Tighten if necessary and replace any defective
parts.
0459 291 601
- 19 -
© ESAB AB 2018
7 FAULT TRACING
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised service
technician.
Type of fault
Action
No arc.
•
•
•
Welding current is interrupted during welding.
•
•
The thermal overload trips operate frequently. •
•
Poor welding performance.
•
•
•
•
0459 291 601
- 20 -
Check that the mains power supply
switch is turned on.
Check that the welding current supply
and return cables are correctly
connected.
Check that the correct current value is
set.
Check whether the thermal overload
trips have operated (indicated by the
orange lamp on the front panel).
Check the main power supply fuses.
Check to see whether the air filters are
clogged.
Make sure that you are not exceeding
the rated data for the power source (i.e.
that the unit is not being overloaded).
Check that the welding current supply
and return cables are correctly
connected.
Check that the correct current value is
set.
Check that the correct electrodes are
being used.
Check the main power supply fuses.
© ESAB AB 2018
8 ORDERING SPARE PARTS
8
ORDERING SPARE PARTS
Mig U5000iw and Mig U5000iw WeldCloud™ are designed and tested in accordance with
the international and European standards IEC/EN 60974-1/-2/-3 and EN 60974-10.
It is the obligation of the service unit which has carried out the service or repair work to
make sure that the product still conforms to the mentioned standards.
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see
esab.com. When ordering, please state product type, serial number, designation and spare
part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.
0459 291 601
- 21 -
© ESAB AB 2018
DIAGRAM
DIAGRAM
0459 291 601
- 22 -
© ESAB AB 2018
DIAGRAM
Cooling unit
0459 291 601
- 23 -
© ESAB AB 2018
ORDERING NUMBERS
ORDERING NUMBERS
Ordering no.
Denomination
Product
Notes
0459 230 883
Welding power source
Mig U5000iw
With cooling unit
0445 400 883
Welding power source
Mig U5000iw
WeldCloud™
With cooling unit and
WeldCloud™ unit
0459 839 018
Spare parts list
Mig 5000i, Mig
U5000i, Mig
5000i
WeldCloud™,
Mig U5000i
WeldCloud™
Technical documentation is available on the Internet at: www.esab.com
0459 291 601
- 24 -
© ESAB AB 2018
SPARE PARTS LIST
SPARE PARTS LIST
Item
Ordering no.
1
0458 398 001 Filter
2
0458 383 991 Front grill
0459 291 601
Denomination
- 25 -
© ESAB AB 2018
ACCESSORIES
ACCESSORIES
0458 530 880
Trolley
0458 603 880
Trolley 2 (for feeder with counterbalance
device and/or 2 gas bottles)
0458 731 880
0278 300 401
Guide pin
(B) Insulating bushing, included in guide pin
0459 145 880
Autotransformer TUA2
0459 291 601
- 26 -
© ESAB AB 2018
ACCESSORIES
0459 307 881
Handle (1 piece) with mounting screws
0459 491 910
Remote control adapter RA12 12 pole
For analogue remote controls to CAN based
equipment.
0459 491 880
Remote control unit MTA1 CAN
MIG/MAG: wire feed speed and voltage
MMA: current and arc force
TIG: current, pulse and background current
0459 491 882
Remote control unit M1 10Prog CAN
Choice of on of 10 programs
MIG/MAG: voltage deviation
TIG and MMA: current deviation
0459 491 883
Remote control unit AT1 CAN
MMA and TIG: current
0459 491 884
Remote control unit AT1 CF CAN
MMA and TIG: rough and fine setting of
current.
Remote control cable 12 pole - 4 pole
0459 554 880
5m
0459 554 881
10 m
0459 554 882
15 m
0459 554 883
25 m
0459 554 884
0.25 m
0459 291 601
- 27 -
© ESAB AB 2018
ACCESSORIES
Connection set 12 pole - 12 pole
0456 528 880
1.7 m
0456 528 890
5m
0456 528 881
10 m
0456 528 882
15 m
0456 528 883
25 m
0456 528 884
35 m
Connection set water 12 pole - 12 pole
0456 528 885
1.7 m
0456 528 895
5m
0456 528 886
10 m
0456 528 887
15 m
0456 528 888
25 m
0456 528 889
35 m
Connection set water
12 pole cable plug - 10 pole cable socket
0459 528 970
1.7 m
0459 528 971
5m
0459 528 972
10 m
0459 528 973
15 m
0459 528 974
25 m
0459 528 975
35 m
0700 006 897
Return cable 5 m 95 mm2
0456 855 880
Water flow guard 0.7 l/min
0461 203 880
Water return flow guard Mech 7 m
0459 291 601
- 28 -
© ESAB AB 2018
ACCESSORIES
0459 579 880
MMC kit for power source Mig
0459 546 880
Connection set for connection of two wire
feed units
0414 191 881
Cooling unit OCE2H
0465 720 002
ESAB ready mixed coolant (10 l / 2.64 gal)
Use of any other cooling liquid than the
prescribed one might damage the equipment.
In case of such damage, all warranty
undertakings from ESAB cease to apply.
0459 291 601
- 29 -
© ESAB AB 2018
For contact information visit esab.com
ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00
http://manuals.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising