ESAB | ES 300i | Instruction manual | ESAB ES 300i User manual

ESAB ES 300i User manual
ES 300i
Welding power source MMA 300 A
Instruction manual
0463 415 101 GB 20170608
Valid for: serial no. 719-xxx-xxxx
TABLE OF CONTENTS
SAFETY .........................................................................................................
4
1.1
Meaning of symbols .................................................................................
4
1.2
Safety precautions ...................................................................................
4
INTRODUCTION ...........................................................................................
7
2.1
Overview ...................................................................................................
7
2.2
Equipment .................................................................................................
7
3
TECHNICAL DATA ........................................................................................
8
4
INSTALLATION..............................................................................................
10
4.1
Location.....................................................................................................
10
4.2
Lifting instructions ...................................................................................
10
4.3
Mains supply.............................................................................................
11
OPERATION ..................................................................................................
15
5.1
Overview ...................................................................................................
15
5.2
Connections and control devices ...........................................................
15
5.3
Connection of welding and return cables ..............................................
15
5.4
Turning the mains power on/off ..............................................................
16
5.5
Fan control ................................................................................................
16
5.6
Thermal protection ...................................................................................
16
5.7
Functions and symbols ...........................................................................
16
5.8
Setting panel .............................................................................................
18
5.8.1
Navigation ..............................................................................................
18
5.8.2
Weld program .........................................................................................
19
5.9
Remote control .........................................................................................
19
5.10
USB connection........................................................................................
19
6
TROUBLESHOOTING ...................................................................................
20
7
ERROR CODES.............................................................................................
21
7.1
Error code descriptions ..........................................................................
21
ORDERING SPARE PARTS ..........................................................................
22
DIAGRAM .............................................................................................................
23
ORDERING NUMBERS ........................................................................................
24
ACCESSORIES ....................................................................................................
25
1
2
5
8
Rights reserved to alter specifications without notice.
0463 415 101
© ESAB AB 2017
1 SAFETY
1
SAFETY
1.1
Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2
Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1.
2.
3.
Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
The workplace must:
○ be suitable for the purpose
○ be free from drafts
0463 415 101
-4-
© ESAB AB 2017
1 SAFETY
4.
5.
Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Install and ground the unit in accordance with instruction manual.
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or
work cable around your body. Keep welding power source and
cables as far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes.
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
• Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
0463 415 101
-5-
© ESAB AB 2017
1 SAFETY
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
• Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
0463 415 101
-6-
© ESAB AB 2017
2 INTRODUCTION
2
INTRODUCTION
2.1
Overview
The ES 300i is a welding power source intended for welding with coated electrodes (MMA)
and TIG welding.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.2
Equipment
The power source is supplied with:
•
•
3 m mains cable with plug
instruction manual
0463 415 101
-7-
© ESAB AB 2017
3 TECHNICAL DATA
3
TECHNICAL DATA
ES 300i (0445 100 880)
Mains voltage
230-480 V±10%, 3~ 50/60 Hz 230 V±10%, 1~ 50/60 Hz
Mains supply Ssc min 2)
4.4 MVA
No demand
Zmax
0.04 Ohm
No demand
Imax MMA
30.0 A
29.0 A
Imax TIG
21.0 A
20.0 A
Primary current
No-load power demand when in the energy-saving mode
Uin 230 V
Uin 480 V
74 W
91 W
Setting range
MMA
5 A / 20 V - 300 A / 32 V
5A / 20 V - 200 A / 28 V
TIG
5 A / 10 V - 300 A / 22 V
5A / 10 V - 200 A / 18 V
Permissible load at MMA
40% duty cycle
300 A / 32.0 V
60% duty cycle
250 A / 30.0 V
100% duty cycle
200 A / 28.0 V
200 A / 28.0 V
Permissible load at TIG
40% duty cycle
300 A / 22.0 V
60% duty cycle
250 A / 20.0 V
100% duty cycle
200 A / 18.0 V
200 A / 18.0 V
Power factor at maximum current
TIG
0.96
0.99
MMA
0.96
0.98
Efficiency at maximum current
MMA
89%
86%
TIG
85%
83%
VRD 35 V deactivated
48 V
48 V
VRD 35 V activated
32 V
34 V
Open-circuit voltage U0 max
Operating temperature
Transportation temperature
-10 to +40 °C (+14 to +104 °F)
-20 to +55 °C (-4 to +131 °F)
Continual sound pressure
at no-load
Dimensions l × w × h
< 70 db (A)
460 × 200 × 320 mm (18.1 × 7.9 × 12.6 in.)
Weight
15 kg (33 lbs)
Insulation class transformer
0463 415 101
F
-8-
© ESAB AB 2017
3 TECHNICAL DATA
ES 300i (0445 100 880)
Enclosure class
IP23
Application class
Mains supply, Ssc min
Minimum short circuit power on the network in accordance with IEC 61000-3-12.
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40 °C / 104 °F, or below.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
0463 415 101
-9-
© ESAB AB 2017
4 INSTALLATION
4
INSTALLATION
The installation must be carried out by a professional.
CAUTION!
This product is intended for industrial use. In a domestic environment this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
4.1
Location
Position the power source so that its cooling air inlets and outlets are not obstructed.
A. Minimum 200 mm (8”)
B. Minimum 200 mm (8”)
WARNING!
Secure the equipment - particularly if
the ground is uneven or sloping.
4.2
Lifting instructions
Mechanical lifting must be done with both outer handles.
0463 415 101
- 10 -
© ESAB AB 2017
4 INSTALLATION
4.3
Mains supply
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the user's
supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to Sscmin. Refer to the technical data in the
TECHNICAL DATA chapter.
The power source will automatically adjust to the supplied input voltage; make sure it is
protected by the correct fuse rating. A protective earth connection must be made, in
accordance with regulations.
Rating plate with supply connection data
0463 415 101
- 11 -
© ESAB AB 2017
4 INSTALLATION
Recommended fuse sizes and minimum cable area ES 300i
Mains voltage
1~
50/60
Hz
3~ 50/60 Hz
Mains cable area
230 V
380 V
400 V
415 V
480 V
4×4 mm²
4×2.5 mm² 4×2.5 mm² 4×2.5 mm² 4×2.5 mm²
230 V
3×6
mm²
Maximal current rating
Imax
MMA
30 A
18 A
16 A
16 A
14 A
28.0
A
I1eff
MMA
18 A
11 A
10 A
10 A
9A
28.0
A
Fuse
anti-surge
20 A
16 A
10 A
10 A
10 A
35 A
type C MCB
20 A
16 A
16 A
16 A
10 A
35 A
Maximum
recommended
extension cord length
Minimum
recommended
extension cord size
100 m/
330 ft.
100 m/
330 ft.
100 m/
330 ft.
100 m/
330 ft.
100 m/
330 ft.
100
m/
330 ft
.
4×4 mm²
4×4 mm²
4×4 mm²
4×4 mm²
4×4 mm²
3×6
mm²
NOTE!
Different variants of ES 300i are certified for different mains voltage. Always refer
to the rating plate for the specification of the power source in use.
NOTE!
The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. Use the power source in accordance with the relevant
national regulations.
1-phase 230 V mains voltage with 16 A mains fuse
See table below for informative data for use at 1-phase 230 V mains voltage with 16 A mains
fuse. A 16 A mains fuse may enable the use of a 16 A mains plug in combination with a
3×2,5 mm2 mains cable.
MMA 1~ 230 V 16 A
25%
60%
100%
I2
200 A*
150 A
120 A
U2
28.0 V
26.0 V
24.8 V
Imax
28.2 A
20.2 A
15.3 A
Ieff
14.1 A
15.6 A
15.3 A
TIG 1~ 230 V 16 A
I2
0463 415 101
60%
100%
200 A*
170 A
- 12 -
© ESAB AB 2017
4 INSTALLATION
U2
18.0 V
16.8 V
Imax
19.1 A
15.3 A
Ieff
14.8 A
15.3 A
*) Porcelain fuses are recommended to achieve 200 A in MMA and TIG mode. MCB fuses
break the circuit faster than porcelain fuses.
Supply from power generators
The power source can be supplied from different types of generators. However, some
generators may not provide sufficient power for the welding power source to operate
correctly. Generators with Automatic Voltage Regulation (AVR) or with equivalent or better
type of regulation, with rated power 20 kW, are recommended.
Installation of mains cable
NOTE!
The power source is delivered with mains cable approved for 380-480 V and plug
for 380-415 V. If other mains voltage is required, the mains cable and plug may
be changed according to relevant national regulations.
1.
2.
3.
Remove the side panel.
If tightened, release the stopping block (A).
If a cable is connected, disconnect all wires, cut the cable tie (D), and remove the
cable.
4. Optional: The fan with foam can at this point be removed to simplify the installation.
Note the direction of the fan (the sticker towards the inside).
5. Strip the new wire according to specification (B).
6. Insert the cable with about 1 cm (0.4 in.) of isolation inside the stopping block. Tighten
the stopping block by using 1.5–2 Nm (13.3–17.7 in. lb) (A).
7. Use a cable tie to fasten the cables (D).
8. Optional: If the fan with foam has been removed it shall now be re-installed. A symbol
on the side of the fan (G) shows the air flow direction.
9. Install the ferrites and connect the earth wire (C). A toothed washer should be located
closest to the heat sink. Tighten the screw to a torque of 6.0 ±0.6 Nm (53.1 ±5.3 in. lb).
10. Connect all wires. Tighten the screw to a torque of 1.0 ±0.2 Nm (8.9 ±1.8 in. lb).
11. Ensure that the IP shield is correctly mounted on the inside of the side panel (E).
0463 415 101
- 13 -
© ESAB AB 2017
4 INSTALLATION
12. Reassemble the side panel (F).
13. Tighten the screws on the side panel with 3 ±0.3 Nm (26.6 ±2.7 in. lb).
0463 415 101
- 14 -
© ESAB AB 2017
5 OPERATION
5
OPERATION
5.1
Overview
General safety regulations for handling the equipment can be found in the chapter
"Safety". Read it through before you start the equipment.
WARNING!
Electric shock! Do not touch the workpiece or the welding head during operation!
5.2
1.
2.
3.
4.
Connections and control devices
Setting panel
Positive welding terminal
Negative welding terminal
Connection for remote control unit
5. Mains power supply switch, O/I
6. USB connection
7. Mains cable
NOTE!
Always use the cover when the USB connection is not in use.
5.3
Connection of welding and return cables
The power source has two outputs, a positive welding terminal (+) and a negative welding
terminal (-), for connecting welding and return cables. The output to which the welding cable
is connected depends on the welding method or type of electrode used.
Connect the return cable to the other output on the power source. Secure the return cable's
contact clamp to the work piece and ensure that there is good contact between the work
piece and the output for the return cable on the power source.
0463 415 101
- 15 -
© ESAB AB 2017
5 OPERATION
•
•
For TIG welding, the negative welding terminal (-) is used for the welding torch and the
positive welding terminal (+) is used for the return cable.
For MMA welding, the welding cable can be connected to the positive welding terminal
(+) or negative welding terminal (-) depending on the type of electrode used. The
connecting polarity is stated on the electrode packaging.
5.4
Turning the mains power on/off
Turn on the mains power by turning switch to the ”I” position.
Turn the unit off by turning the switch to the ”O” position.
Whether the mains power supply is interrupted or the power source is switched off in the
normal manner, weld programs will be stored so that it is available next time the unit is
started.
CAUTION!
Do not turn off the power source during welding (with load).
5.5
Fan control
The power source has an automatic thermal control. The fan continues to run during a few
minutes after welding has stopped while the power source switches to energy-saving mode.
The fan starts again when welding restarts.
During energy-saving mode the fan will start occasionally and run for a few minutes.
5.6
Thermal protection
The power source includes thermal protection against overheating. When
overheating occurs the welding is stopped and overheating indicator on the
panel will be lit and an error message shows in the display. The protection is
automatically reset when the temperature has been sufficiently reduced.
5.7
Functions and symbols
Hot start
The hot start function temporarily increases the current in the beginning of the
weld. Use this function to reduce risk of insufficient fusion and electrode sticking
and scratching.
Hot start only applies to MMA welding.
Cel 6010
Optimised arc characteristics for cellulosic electrodes such as 6010 and similar.
0463 415 101
- 16 -
© ESAB AB 2017
5 OPERATION
TIG welding
TIG welding melts the metal of the workpiece, using an arc struck from a
tungsten electrode that does not melt. The weld pool and electrode are
protected by shielding gas.
For TIG welding, the welding power source shall be supplemented with:
•
•
•
•
a TIG torch with gas valve
an argon gas cylinder
an argon gas regulator
tungsten electrode
This power source performs Live TIG start.
The tungsten electrode is placed against the workpiece. When lifted away from
workpiece the arc is struck at a limited current level.
Voltage Reduction Device (VRD)
The VRD function ensures that the open-circuit voltage does not exceed 35 V
when welding is not being carried out. This is indicated by a lit VRD indicator on
the panel. Contact an authorised ESAB service technician to activate this
function.
0463 415 101
- 17 -
© ESAB AB 2017
5 OPERATION
5.8
Setting panel
1. Buttons for weld program, see section
WELD PROGRAM.
2. Display, shows set or measured value.
3. Choice of welding method MMA or TIG.
7. Display parameter indicator.
8. Set indicator.
9. Select parameter to show in display,
indicated by (7).
10. Overheating indication.
4. Choice of electrode type "cellulose" for
MMA welding.
5. Activate/deactivate of remote control unit. 11. VRD function (reduced open-circuit
voltage) indicator.
6. Knob for setting data.
NOTE!
The described functionality is not affected by possible visual differences in the
setting panel image.
5.8.1
Navigation
Parameter selection
By pressing the button (9) different values can be shown and changed. Use the knob (6) to
change the values. The sequence is:
1.
2.
3.
4.
5.
Set current values.
Measured current values.
Measured voltage values.
Hot start, setting range: 0-100%, default: 0%. (only MMA)
Arc force, 0-100%. (only MMA)
Set parameter
0463 415 101
- 18 -
© ESAB AB 2017
5 OPERATION
The set indicator (8) will be lit when a value can be changed. It cannot be changed from the
panel when a remote control is activated. Trying to change a value while in measured value
mode will result in automatically move to set current value mode.
5.8.2
Weld program
For each welding process (MMA/TIG) three different weld programs can be stored in the
setting panel memory (1). Press selection button 1, 2 or 3 for 3 seconds to store a weld
program in the memory. The memory indicator will be lit when finished.
To switch between the different weld programs press button 1, 2 or 3.
5.9
Remote control
Connect the remote control on the rear side of the power source and activate the
remote control by pressing the remote control button on the panel (remote
control indicator being lit when activated). When the remote control is activated
the control panel is locked for interaction but displays welding data.
5.10
USB connection
Always use the USB cover when the USB connection is not in use.
Do not use for charging units such as mobile phones.
The welding process is blocked when a USB flash drive is connected. The USB
connection can be used to retrieve welding statistics. The statistics contains of
total number of welds performed, total welding time and average current.
Retrieving welding statistics
Always make sure that the power source is not used for welding when retrieving
welding statistics.
1.
2.
3.
4.
5.
0463 415 101
Insert an empty USB flash drive into the power source USB connector.
To confirm that the power source has read the USB flash drive, the text
"USB" flashes in the display for a moment, after which the text "USB" is
shown with fixed light.
When the text "USB" is shown with fixed light: Remove the USB flash drive
from the USB connector.
The USB flash will contain a text file (.txt) with the welding statistics.
Recommended program for opening the text file is Microsoft WordPad or
Microsoft Word.
- 19 -
© ESAB AB 2017
6 TROUBLESHOOTING
6
TROUBLESHOOTING
Perform these checks and inspections before sending for an authorised service technician.
Type of fault
Corrective action
MMA welding problems
• Check that the welding and return cables are correctly
connected on the power source.
• Make sure the return clamp has proper contact with the
work piece.
• Check that the correct electrodes and polarity are being
used. For polarity, check electrode packaging.
• Check that the correct current value is set.
• Adjust Arc Force and Hot start.
TIG welding problems
• Check that the welding and return cables are correctly
connected on power source.
• Make sure the return clamp has proper contact with the
work piece.
• Make sure the TIG torch lead is connected to negative
welding terminal.
• Make sure the correct shielding gas, gas flow, welding
current, filler rod placement, electrode diameter and
welding mode on power source is used.
• Make sure the gas valve on the TIG torch is on.
No arc
• Check that display is on to verify that the power source has
power.
• Check setting panel display correct values.
• Check that the mains power supply switch is turned on.
• Check that the mains, welding and return cables are
correctly connected.
• Check the mains power supply fuses.
Welding current is
interrupted during welding
• Check whether the overheating light (thermal protection) at
setting panel is on.
• Continue with fault type "No Arc".
The thermal protection
trips frequently
• Make sure the recommended duty cycle for the weld
current has not been exceeded.
See section "Duty cycle" in the TECHNICHAL DATA
chapter.
• Make sure the air inlets or outlets are not clogged.
• Clean inside machine according to routine mainteance.
0463 415 101
- 20 -
© ESAB AB 2017
7 ERROR CODES
7
ERROR CODES
The error code is used to indicate that a fault has occurred in the equipment. Errors are
indicated by the text "Err" followed by the error code number shown in the display.
If several errors have been detected only the code for the last occurring error is displayed.
7.1
Error code descriptions
Error codes that the user can handle are listed below. If any other error code appears,
contact an authorised ESAB service technician.
Error code Description
Err 1
Temperature fault
The temperature of the power source is too high. A LED indicating
temperature fault is also lit on the panel.
Action: The error code will automatically disappear and the LED indicating
temperature fault will be turned off when the power source has cooled off and
is ready for use again.
Err 3
Power supply fault
The power supply to the power source is too low or too high.
Action: Make sure the power supply is stable, all leads are connected, that
the mains voltage (all 3 phases) are OK and restart the system. If the error
persists, contact a service technician.
Err 4
Communication fault
The communication in the power source has been disrupted.
Action: Restart the power source. If the error persists, contact a service
technician.
Err 5
Memory fault
The program memory is damaged. This fault can disable preset functions or
other functions where values are stored.
Action: Remove the error indication from the display by pressing a button on
the panel. Restart the power source. If the error persists, contact a service
technician.
Err 6
Timing fault
The power source electronics are not able to execute all functions in a timely
fashion.
Action: Restart the power source. If the error persists, contact a service
technician.
Err 7
OCV fault
The OCV is too high or the electronic control of the OCV has been disrupted.
Action: Restart the power source. If the error persists, contact a service
technician.
0463 415 101
- 21 -
© ESAB AB 2017
8 ORDERING SPARE PARTS
8
ORDERING SPARE PARTS
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
The ES 300i is designed and tested in accordance with international and european
standards IEC/EN 60974-1 and IEC/EN 60974-10. On completion of service or repair work,
it is the responsibility of the person(s) performing the work to ensure that the product still
complies with the requirements of the above standard.
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see the back
cover of this document. When ordering, please state product type, serial number, designation
and spare part number in accordance with the spare parts list. This facilitates dispatch and
ensures correct delivery.
0463 415 101
- 22 -
© ESAB AB 2017
DIAGRAM
DIAGRAM
0463 415 101
- 23 -
© ESAB AB 2017
ORDERING NUMBERS
ORDERING NUMBERS
Ordering number
Denomination
Type
0445 100 880
Welding power source ES 300i
0463 423 001
Spare parts list
Notes
Europe
ES 300i
Technical documentation is available on the Internet at www.esab.com
0463 415 101
- 24 -
© ESAB AB 2017
ACCESSORIES
ACCESSORIES
TIG torches
0700 300 539
TXH™ 151 V, OKC 50, 4 m
0700 300 545
TXH™ 151 V, OKC 50, 8 m
0700 300 553
TXH™ 201 V, OKC 50, 4 m
0700 300 556
TXH™ 201 V, OKC 50, 8 m
0460 330 881
Trolley
0445 197 880
Shoulder strap kit
0700 006 902
Electrode holder OKC 50, 3 m
0700 006 888
Electrode holder OKC 50, 5 m
0700 006 903
Return cable OKC 50, 3 m
0700 006 889
Return cable OKC 50, 5 m
0160 360 881
OKC 50 male contact, pack 4 pcs
0445 536 881
ER 1 Remote control
(5 m (16.4 ft) interconnection cable, 6 pin,
included)
0445 280 880
Interconnection cable, 6 pin, 5 m (16.4 ft)
0445 280 881
Interconnection cable, 6 pin, 10 m (32.8 ft)
0445 280 882
Interconnection cable, 6 pin, 25 m (82 ft)
0463 415 101
- 25 -
© ESAB AB 2017
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Heist-op-den-Berg
Tel: +32 15 25 79 30
Fax: +32 15 25 79 44
BULGARIA
ESAB Kft Representative Office
Sofia
Tel: +359 2 974 42 88
Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
SOUTH AFRICA
ESAB Africa Welding & Cutting
Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
USA
ESAB Welding & Cutting
Products
Florence, SC
Tel: +1 843 669 4411
Fax: +1 843 664 5748
Asia/Pacific
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GERMANY
ESAB Welding & Cutting GmbH
Langenfeld
Tel: +49 2173 3945-0
Fax: +49 2173 3945-218
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
SWITZERLAND
ESAB Europe GmbH
Baar
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
www.esab.com
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 0220
Fax: +1 905 670 4879
SPAIN
ESAB Ibérica S.A.
San Fernando de Henares
(MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising