ESAB | Mig C420 PRO | Instruction manual | ESAB Mig C420 PRO User manual

ESAB Mig C420 PRO User manual
Origo™
Mig C420 PRO
Instruction manual
0463 272 001 GB 20170310
Valid for: serial no. 627-xxx-xxxx, 120-xxx-xxxx
TABLE OF CONTENTS
1
SAFETY .........................................................................................................
4
1.1
Meaning of symbols .................................................................................
4
1.2
Safety precautions ...................................................................................
4
INTRODUCTION ............................................................................................
7
2.1
Equipment .................................................................................................
7
3
TECHNICAL DATA ........................................................................................
8
4
INSTALLATION..............................................................................................
10
4.1
Location.....................................................................................................
10
4.2
Assembly of components........................................................................
10
4.3
Electrical installation ...............................................................................
11
4.4
Mains power supply .................................................................................
11
OPERATION ..................................................................................................
13
5.1
Connection and control devices .............................................................
14
5.2
Start ...........................................................................................................
14
5.3
Overheating protection ............................................................................
14
5.4
Water connection .....................................................................................
15
5.5
Water flow guard ......................................................................................
15
5.6
Idle mode...................................................................................................
15
5.7
Mig C420w PRO / Mig C420 PRO ............................................................
15
5.8
Polarity change.........................................................................................
16
5.9
Wire feed pressure ...................................................................................
16
5.10
Replacing and inserting wire...................................................................
16
MAINTENANCE .............................................................................................
18
6.1
Inspection and cleaning...........................................................................
18
6.2
Topping up the coolant ............................................................................
19
7
TROUBLESHOOTING ...................................................................................
20
8
ORDERING SPARE PARTS ..........................................................................
21
CLEANING............................................................................................................
22
DIAGRAM .............................................................................................................
23
ORDERING NUMBERS ........................................................................................
25
WEAR PARTS.......................................................................................................
26
ACCESSORIES ....................................................................................................
28
2
5
6
Rights reserved to alter specifications without notice.
0463 272 001
© ESAB AB 2017
1 SAFETY
1
SAFETY
1.1
Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2
Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1.
2.
3.
Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
The workplace must:
○ be suitable for the purpose
○ be free from drafts
0463 272 001
-4-
© ESAB AB 2017
1 SAFETY
4.
5.
Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Install and ground the unit in accordance with instruction manual.
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or
work cable around your body. Keep welding power source and
cables as far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes.
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
• Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.
0463 272 001
-5-
© ESAB AB 2017
1 SAFETY
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
• Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment and its implementation
in accordance with national law, electrical and/or electronic
equipment that has reached the end of its life must be
disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.
0463 272 001
-6-
© ESAB AB 2017
2 INTRODUCTION
2
INTRODUCTION
The Mig C420 PRO is a step-controlled compact welding power source incorporating wire
feed mechanism intended for MIG/MAG welding with solid wires of steel, stainless steel or
aluminium, and cored wires with or without shielding gas.
The Mig C420w PRO is equipped with a cooling liquid system for welding torches. The Mig
C420 PRO is not equipped with a cooling system and can operate only with appropriate gas
cooled torches.
The power units are fan-cooled and equipped with thermal overload protection.
The power sources can be fitted with a flow guard (Mig C420w PRO).
The power source comes in different variants, see "ORDERING NUMBERS" chapter.
ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.1
Equipment
The power source is supplied with:
•
•
•
•
Welding torch PSF 405/410w - 4.5 m
Return cable 5 m with return clamp
Shelf for gas cylinder
Instruction manual
0463 272 001
-7-
© ESAB AB 2017
3 TECHNICAL DATA
3
TECHNICAL DATA
Mig C420 PRO
Voltage
400 - 415 V, 3~ 50 Hz
Permissible load
at 100% duty cycle
315 A/30 V
at 60% duty cycle
400 A/34 V
at 50% duty cycle
420 A/35 V
Setting range (DC)
50 A/16.5 V - 420 A/35 V
Open circuit voltage
14 - 47 V
Open circuit power
520 W
with cooling unit
730 W
Efficiency
77%
Power factor
0.92
Control voltage
42 V, 50/60 Hz
Wire feed speed
1.9 - 25.0 m/min
Burnback time
0 - 0.5 s
Creep start
OFF / ON
2/4 stroke
2/4
Welding torch connection
EURO
Max diameter of wire bobbin
300 mm
Wire dimension range
0.6 - 1.6 mm
Dimensions LxWxH
935 x 640 x 800 mm
Weight
215 kg
with cooling unit
230 kg
Operating temperature
-10 to +40 °C
Transportation temperature
-20 to +55 °C
Enclosure class
IP 23
Application class
Cooling unit (100 % duty cycle)
P1l/min
1200 W at 25 °C
pmax
3.5 bar
Coolant
ESAB's ready mixed coolant
Coolant quantity
5.5 l
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40 °C / 104 °F, or below.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP23 is intended for indoor and outdoor use.
0463 272 001
-8-
© ESAB AB 2017
3 TECHNICAL DATA
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
0463 272 001
-9-
© ESAB AB 2017
4 INSTALLATION
4
INSTALLATION
The installation must be carried out by a professional.
NOTE!
Connect the power source to the electricity mains with a network impedance of
0.268 W or lower. If the network impedance is higher, there is a risk of flicker in
the illuminators.
CAUTION!
This product is intended for industrial use. In a domestic environment this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
4.1
Location
Position the welding power in source such a way that its cooling air inlets and outlets are not
obstructed.
WARNING!
Straps must be used when lifting the
power source. The handle is only
intended for pulling it.
4.2
0463 272 001
Assembly of components
- 10 -
© ESAB AB 2017
4 INSTALLATION
WARNING!
During transport, the rear wheels of the power source are in their forward
position. Before use, place the wheels in their rear position.
4.3
Electrical installation
4.4
Mains power supply
Check that the unit is connected to the correct mains power supply voltage, and that it is
protected by the correct fuse size. A protective earth connection must be made, in
accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable areas
Mig C420 PRO
3~ 50 Hz
Voltage V
400 - 415
Current A
at 100% duty cycle
19
at 60% duty cycle
27
at 50% duty cycle
30
Cable area mm2
4x4
Fuse, slow A
25
0463 272 001
- 11 -
© ESAB AB 2017
4 INSTALLATION
NOTE!
The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. For other regions, supply cables must be suitable for the
application and meet local and national regulations.
0463 272 001
- 12 -
© ESAB AB 2017
5 OPERATION
5
OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
WARNING!
Rotating parts can cause injury, take great care.
WARNING!
To prevent the reel from sliding off the
hub: Lock the reel in place by turning
the red knob as shown on the warning
label attached next to the hub.
WARNING!
Secure the equipment - particularly if
the ground is uneven or sloping.
0463 272 001
- 13 -
© ESAB AB 2017
5 OPERATION
5.1
Connection and control devices
1. Mains supply switch
2.
3.
4.
5.
6.
7.
8.
9.
10. Connection for return cable (-), medium
inductance
Switch, coarse control
11. Connection for return cable (-), low
inductance
Switch, precise control
12. Knob for wire speed setting
Indicator lamp, power supply ON
13. Knob for selecting 2/4-stroke control mode
Orange indicating lamp, overheating and 14. Knob for selecting - creep start - ON/OFF
loss of coolant*
EURO - connector (for welding torch)
15. Knob for burn-back time setting
Connection for cooling water to the
16. Digital instrument - V / A
welding torch (Blue - with ELP** switch)
Connection for cooling water from the
17. Water flow guard (option, see
welding torch (Red)
"ACCESSORIES" chapter)
Connection for return cable (-), high
inductance
* Indicating loss of coolant, only when water flow guard is used, see "Water flow guard"
section.
** ELP = ESAB Logic Pump, see "Water connection" section.
5.2
Start
When switched on, indicator lamps [4,5] are on for 2 seconds. Normally, if the power source
is not overheated, it should start to work in idle mode, which is indicated by blinking of the
supply ON lamp. The fan and the coolant pump are stopped. The fan starts at the first start of
welding. The coolant pump starts at the same moment, if it is switched on with ELP switch on
the water outlet [7].
5.3
Overheating protection
The power source has 2-step control of fan speed and overheating protection. If temperature
crosses the threshold point, the fan starts to run with increased speed. If the internal
0463 272 001
- 14 -
© ESAB AB 2017
5 OPERATION
temperature becomes too high, the welding is interrupted and disabled. This state is
indicated by permanent lighting of the orange indicating lamp on the front of the unit. It resets
automatically when the temperature falls down.
5.4
Water connection
The Mig C420w PRO has a sensor ELP, ESAB Logic Pump, which senses whether the water
hoses of the welding torch are connected. When a water-cooled welding torch is connected,
the water pump is active.
It is recommended to switch the power source off by means of the mains switch ON/OFF [1]
for connecting the cooling water hoses to/from the Mig C420w PRO.
5.5
Water flow guard
The power sources with cooling unit (Mig C420w PRO) can be fitted with a water flow guard
(option - see "ACCESSORIES" chapter).
The water flow guard interrupts and disables welding in event of loss of coolant. This state is
indicated by the orange indicating lamp on the front of the power source flashing. If there is a
lack of coolant flow, after 1 min the pump is switched off and locked in this state. The pump
restarts from that state along with start of welding.
5.6
Idle mode
The power source has an idle mode. The fan is switched off 5 min after the end of the last
welding, or after 5 min of work with decreased speed without welding. The pump is switched
off 3 min after the last welding. When both fan and pump are switched off the power supply
lamp [4] on the front panel flashes.
5.7
Mig C420w PRO / Mig C420 PRO
The Mig C420w PRO / Mig C420 PRO is equipped with a standard control unit. The welder
can manually select and adjust all welding parameters.
•
•
•
•
Wire speed (1.9 - 25 m/min) is set with knob [12].
The stroke control (2/4 stroke) is selected with switch [13].
Creep start i.e. start with 50% wire speed is toggled ON/OFF with switch [14].
Burn back time is set with knob [15].
Mig C420w PRO / Mig C420 PRO can be fitted with a digital instrument that displays current
and voltage. It incorporates a hold function (see "ACCESSORIES" chapter).
0463 272 001
- 15 -
© ESAB AB 2017
5 OPERATION
5.8
Polarity change
The power source is delivered with the welding wire connected to the plus pole. Some wires,
e.g self shielded cored wires, are recommended for welding with negative polarity. Negative
polarity means that the wire is connected to the minus pole and the return cabel to the plus
pole.
Check the recommended polarity for the welding wire you want to use.
5.9
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then set the
pressure of the wire feeder's pressure rollers. It is important that the pressure is not too
great.
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against an
insulated object, e.g. a piece of wood.
When you hold the torch approx. 5 mm from the piece of wood (fig. 1) the feed rollers should
slip.
If you hold the torch approx. 50 mm from the piece of wood, the wire should be fed out and
bend (fig. 2).
5.10
•
•
Replacing and inserting wire
Open the side panel.
Disconnect the pressure sensor by folding it backwards, the pressure rollers slide up.
0463 272 001
- 16 -
© ESAB AB 2017
5 OPERATION
•
•
•
•
Straighten out 10-20 cm of new wire. File off any burrs and sharp edges from the end
of the wire before inserting it into the wire feed unit.
Make sure that the wire goes properly into the feed roller track and into the outlet
nozzle and the wire guide.
Secure the pressure sensor.
Close the side panel.
0463 272 001
- 17 -
© ESAB AB 2017
6 MAINTENANCE
6
MAINTENANCE
NOTE!
Regular maintenance is important for safe and reliable operation.
CAUTION!
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
CAUTION!
All warranty undertakings from the supplier cease to apply if the customer
attempts any work to rectify any faults in the product during the warranty period.
6.1
Inspection and cleaning
Power source
Check regularly that the power source is free from dirt.
The power source should be regularly blown clean using dry compressed air at reduced
pressure, see "CLEANING" chapter. This should be done more frequently in dirty
environments.
Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid this you
can use an airfilter.
The airfilter is an accessory. Order number can be found in the "ACCESSORIES" chapter.
Welding torch
The welding torch's wear parts should be cleaned and replaced at regular intervals in order
to achieve trouble-free wire feed. Blow the wire guide clean regularly and clean the contact
tip.
The brake hub
The hub is adjusted when delivered, if readjustment is required, follow the instructions below.
Adjust the brake hub so that wire is slightly slack when wire feed stops.
• Adjusting the braking torque:
○ Turn the red handle to the locked
position.
○ Insert a screwdriver into the springs in
the hub.
Turn the springs clockwise to reduce the
braking torque.
Turn the springs counter-clockwise to
increase the braking torque.
Note: Make sure you turn both springs
the same amount.
0463 272 001
- 18 -
© ESAB AB 2017
6 MAINTENANCE
6.2
Topping up the coolant
ESAB's ready mixed coolant is recommended for use.
See accessories in the "ACCESSORIES" chapter.
NOTE!
Coolant must be topped up if connecting a Push-Pull
welding torch that is 6 meters in length or longer.
When adjusting the water level by topping up, the
coolant hose does not need to be disconnected.
CAUTION!
The coolant must be handled as chemical waste.
0463 272 001
- 19 -
© ESAB AB 2017
7 TROUBLESHOOTING
7
TROUBLESHOOTING
Try these recommended checks and inspections before sending for an authorised service
technican.
Type of fault
Actions
No arc
• Check that the mains power supply switch is turned on.
• Check that the welding current supply and return cables
are correctly connected.
• Check that correct current value is set.
Welding current is
interrupted during welding
• Check whether the thermal overload trip has operated
(indicated by the orange lamp on the front).
• Check the main power supply fuses.
Thermal overload trips
operate frequently
• Check to see whether the air filters are clogged.
• Make sure that you are not exceeding the rated data for
the power source (i.e. that the unit is not being
overloaded).
Poor welding performance
• Check that the welding current supply and return cables
are correctly connected.
• Check that the correct current value is set.
• Check that the correct welding wires are being used.
• Check the main power supply fuses.
• Check the wire feed unit - that proper rolls are applied and
properly set the pressure of the wire feeder's pressure
rollers.
0463 272 001
- 20 -
© ESAB AB 2017
8 ORDERING SPARE PARTS
8
ORDERING SPARE PARTS
CAUTION!
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Mig C420 PRO is designed and tested in accordance with the international and
European standards EN 60974-1, EN 60974-5 and EN 60974-10. It is the obligation of
the service unit which has carried out the service or repair work to make sure that the
product still conforms to the said standard.
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see the back
cover of this document. When ordering, please state product type, serial number, designation
and spare part number in accordance with the spare parts list. This facilitates dispatch and
ensures correct delivery.
0463 272 001
- 21 -
© ESAB AB 2017
CLEANING
CLEANING
0463 272 001
- 22 -
© ESAB AB 2017
DIAGRAM
DIAGRAM
0463 272 001
- 23 -
© ESAB AB 2017
DIAGRAM
0463 272 001
- 24 -
© ESAB AB 2017
ORDERING NUMBERS
ORDERING NUMBERS
Ordering no.
Type
Notes
0349 312 580
OrigoTM Mig C420 PRO
400−415V 3~ 50Hz, with digital instrument
0349 312 590
OrigoTM Mig C420w PRO
400−415V 3~ 50Hz; with water cooler and
digital instrument
0349 300 538
OrigoTM Mig C420 PRO
Spare parts list
Technical documentation is available on the Internet at: www.esab.com
0463 272 001
- 25 -
© ESAB AB 2017
WEAR PARTS
WEAR PARTS
Item Denomination
Ordering no. Notes
0459 052 001 Ø 0.6 & 0.8 mm; Fe, Ss & cored wire; V-groove
0459 052 002 Ø 0.8 & 1.0 mm; Fe, Ss & cored wire; V-groove
0459 052 003 Ø 0.9/1.0 & 1.2 mm; Fe, Ss & cored wire;
V-groove
A
Feed / pressure
roller
0459 052 013 Ø 1.4 & 1.6 mm; Fe, Ss & cored wire; V-groove
0458 825 001 Ø 0.9/1.0 & 1.2 mm; Cored wire; V-groove;
knurled
0458 825 002 Ø 1.2 & 1.4 mm; Cored wire; V-groove; knurled
0458 825 003 Ø 1.6 & 2.0 mm; Cored wire; V-groove; knurled
0458 824 001 Ø 0.8 & 0.9/1.0 mm; Al wire; U-groove
0458 824 003 Ø 1.2 & 1.6 mm; Al wire; U-groove
B
Gear adapter
0459 441 880 Replacing 0455 053 880
C
Inlet nozzle
0455 049 001
D
Drive gear
0459 440 001 Replacing 0455 052 001
E
Intermediate nozzle 0455 072 002 Fe, Ss & cored wire
0456 615 001 Al wire
F
Outlet nozzle
0469 837 880 Ø 2.0 mm steel for 0.6-1.6 mm Fe, Ss & cored
wire
0469 837 881 Ø 2.0 mm plastic for 0.8-1.6 mm Al wire
G
Liner
0349 303 018 Fe, Ss & cored wire
0455 894 001 Al wire
The rollers are marked with wire dimension in mm, some are also marked with inch.
Welding with aluminium wires
In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires
MUST be used. It is recommended to use 3 m long welding torch for aluminium wires,
equipped with appropriate wear parts.
0463 272 001
- 26 -
© ESAB AB 2017
WEAR PARTS
0463 272 001
- 27 -
© ESAB AB 2017
ACCESSORIES
ACCESSORIES
0349 302 451
Digital meter
0349 302 250
Transformer kit for CO2 heater
0349 302 251
Water flow guard
0465 720 002
ESAB ready mixed coolant (10 l / 2.64 gal)
Use of any other cooling liquid than the
prescribed one might damage the equipment.
In case of such damage, all warranty
undertakings from ESAB cease to apply.
0349 302 252
Filter
0463 272 001
- 28 -
© ESAB AB 2017
ACCESSORIES
0349 303 362
Cable holder
0349 308 337
Push-Pull connection kit
Push-Pull welding torches:
0700 200 015
MXH 400w PP - 6.0 m
0700 200 016
MXH 400w PP - 10.0 m
0463 272 001
- 29 -
© ESAB AB 2017
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Heist-op-den-Berg
Tel: +32 15 25 79 30
Fax: +32 15 25 79 44
BULGARIA
ESAB Kft Representative Office
Sofia
Tel: +359 2 974 42 88
Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
SOUTH AFRICA
ESAB Africa Welding & Cutting
Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
USA
ESAB Welding & Cutting
Products
Florence, SC
Tel: +1 843 669 4411
Fax: +1 843 664 5748
Asia/Pacific
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GERMANY
ESAB Welding & Cutting GmbH
Langenfeld
Tel: +49 2173 3945-0
Fax: +49 2173 3945-218
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
SWITZERLAND
ESAB Europe GmbH
Baar
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
www.esab.com
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 0220
Fax: +1 905 670 4879
SPAIN
ESAB Ibérica S.A.
San Fernando de Henares
(MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising